Professional Documents
Culture Documents
شرح عملي CCNA2 مع أل Troubleshooting التي واجهتنا فى LAB اليوم وطرق حلها
شرح عملي CCNA2 مع أل Troubleshooting التي واجهتنا فى LAB اليوم وطرق حلها
LAB
Router 0
1-
Router>ena
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface serial 2/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#exit
Ping 0 1
Router(config-if)#no shutdown
Router#show interfaces :
)Serial2/0 is administratively down, line protocol is down (disabled
show interface :
(Serial2/0 is down, line protocol is down (disabled
(line protocol is down (disabled
DCE DTE
DTE DCE
Router# show controllers serial 2/0
Troubleshooting
Interface Serial2/0
Hardware is PowerQUICC MPC860
DCE V.35, clock rate 64000
DTE DCE
R1
2-
R1
Router>ena
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface serial 2/0
Router(config-if)#ip address 192.168.1.2 255.255.255.0
Router(config-if)#no shutdown
DTE DCE
IP Ping
R0 :
Router(config)#hostname Gaza
Gaza(config)#
Gaza(config)#ip host W.B 192.168.1.2
Gaza#ping 192.168.1.2
Type escape sequence to abort.
R1:
W.B#
W.B#config t
Enter configuration commands, one per line. End with CNTL/Z.
W.B(config)#line vty 0 4
W.B(config-line)#password cisco
W.B(config-line)#login
W.B(config-line)#exit
W.B(config)#
Telnet
Gaza#
Gaza#telnet W.B
Trying 192.168.1.2 ...Open
User Access Verification
Password:
W.B>ena
% No password set.
W.B>
Telnet
% No password set.
W.B(config)#enable secret cisco
Gaza#telnet W.B
Trying 192.168.1.2 ...Open
User Access Verification
Password:
W.B>ena
Password:
W.B#
R2 R3
Lap
Rip
[summarization
-1
Ip Ip
192.168.1.0
192.168.2.0
192.168.3.0
Ip Rip IP
C
192.168.1.0
193.168.1.0
194.168.1.0
IP RIP
clock rate
-2
Show ip interface
RIP
-1
W.B#show ip route
C 180.16.0.0/16 is directly connected, Serial3/0
C 192.168.1.0/24 is directly connected, Serial2/0
W.B#
-2 RIP
W.B#
W.B#config t
Enter configuration commands, one per line. End with CNTL/Z.
W.B(config)#router rip
W.B(config-router)#network 180.16.0.0
W.B(config-router)#network 192.168.1.0
IP
W.B#show ip protocol
Routing Protocol is "rip"
Sending updates every 30 seconds, next due in 22 seconds
Invalid after 180 seconds, hold down 180, flushed after 240
Outgoing update filter list for all interfaces is not set
Incoming update filter list for all interfaces is not set
Redistributing: rip
Default version control: send version 1, receive any version
Interface
Send Recv Triggered RIP Key-chain
Serial3/0
1 21
Serial2/0
1 21
Automatic network summarization is in effect
Maximum path: 4
Routing for Networks:
180.16.0.0
192.168.1.0
Passive Interface(s):
Routing Information Sources:
Gateway
Distance
Last Update
Distance: (default is 120)
W.B#
W.B#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
C 180.16.0.0/16 is directly connected, Serial3/0
C 192.168.1.0/24 is directly connected, Serial2/0
W.B#
W.B#show ip interface serial 2/0
Serial2/0 is up, line protocol is up (connected)
Internet address is 192.168.1.2/24
Broadcast address is 255.255.255.255
Address determined by setup command
MTU is 1500