Professional Documents
Culture Documents
Bts Com Ru10
Bts Com Ru10
Bts Com Ru10
(WN5.0 RU10)
Commissioning overview
Commissioning Step
Select Commissioning Target BTS Site : to configure BTS and Transmission parameter BTS TRS : to configure BTS parameter only : to configure Transmission parameter only
Status Bar
Commissioning Target
BTS Create commissioning file for BTS only. TRS Create commissioning file for Transmission Sub-module (TRS) only. BTS Site - Create commissioning files for BTS and TRS
Commissioning Type
BTS Id is unique identifier in Radio Network Subsystem A2EA is disabled here as Flexi Transport mode configured is Iub IP. FHA Flexi High Speed Adapter (I-HSPA)
RNC Operation and Maintenance Unit (OMU) IP address NTP Server Network Time Protocol Server
PDH/SDH
RNC WCDMA BTS
Supported ATM interfaces are PDH and SDH interfaces, IMA groups, and pseudowires on a PSN tunnel The IUB Terminations via One Virtual Path option is disabled and cleared if the configuration contains more than one ATM interface or pseudowire
If the UBR+ is enabled, enter the minimum desired cell rate in the Min. Desired Cell Rate field and the UBR share in the UBR Share field
This page is available if the I-HSPA Adapter is selected to be in use and the ATM Iu-PS/Iur is selected to be in use
Configuring Iub Transport ATM over Ethernet, IP Iub, Dual Iub, DCN and IP Setting
Only one Ethernet interface can be selected to be in use, except for FTIB with Iub IP transport mode. When FTIB is using Iub IP mode, two Ethernet interfaces can be selected.
IP address/subnet of the enabled Ethernet Interface on TRS and the corresponding bandwidth. Select Include Ethernet Overhead to include Ethernet overhead in shaping.
This page is available if the FTIA, FTIB or FTJA unit is in the TRS and an Ethernet interface has been configured to be in use In Dual Iub traffic mode, the path is used for user plane traffic, and in Iub IP mode it is used for all traffic
Lowest priority
VLAN Priority and VLAN ID are contained in Ethernet Frame (IEEE802.1Q VLAN Tagging) VLAN Priority CFI VLAN ID (12 bits) Cannonical format indication (1 bit) VLAN/User priority (3 bits => values 07) 7 highest priority 0 lowest priority DSCP is a part of IP header Not used (2 bits) DSCP (DiffServ Code Points) 6 bits
DS Differentiated Service field in IP header 1 byte (former TOS Type of Service field)
You need to have a valid licence before the ATM Over Ethernet functionality can be activated
E1/T1
STM-1/ OC3
3G BTS
Ethernet
Packet Network
Ethernet
RNC
NBAP SCTP IP
RNC
BFD is a network protocol used to detect faults between two forwarding engines.
Ethernet
Packet Network
Router
3G BTS
For internal use 41 Nokia Siemens Networks Presentation / Author / Date
RNC
This page is available if the transmission submodule used is FTIB and an Ethernet interface has been configured to be in use
This page is not available if the Flexi HSPA Adapter (I-HSPA Adapter) is selected to be in use but the ATM IuPS/Iur is not in use
Defining IP Filtering
It is not recommended to set the restricted mode off. The restricted mode is a security feature for the DCN network
At least one of the synchronisation sources must be selected to be in use for BTS fault management
Local cell identifiers are determined at the network planning stage. It is essential that the value input matches the expected value in the radio network plan. You should not select the values arbitrarily
RX 1 M RX 2 M RX 1 D RX 2 D
ANT 1
RX switch Sector 2 PA
RX 3 M
ANT 3
ANT 4
RX 1 M RX 2 M RX 1 D RX 2 D
ANT 1
RX switch PA
RX 3 M
ANT 3
ANT 4
Note that if the System Module FSMB is used in the configuration, it is mandatory to use the Extension System Module to get the Local cell groups in use Local cells with the same UARFCN value must belong to the same local cell group.
HSDPA Shared Scheduler for BTS license overrides Minimum Baseband and 16 HSDPA Users per Cell Full Baseband HSDPA Resource Allocation overrides the HSDPA Shared Scheduler for BTS license
M-ECN related
Moderate delay region between Minimum and Middle. Severe delay region between Middle and Maximum.
Probability value for data rate reduction increases with increased delay rate.
Multilevel Explicit Congestion Notification Delay Reference Time Frame Sequence Number
In case of Default in Use is selected for HSUPA Resource Allocation, baseband resources for HSUPA are allocated dynamically. In case of user defined resource allocation baseband resources are allocated statically based on number of HSUPA users and Minimum Baseband Decoding Capacity in Mbps.
GBR - Guaranteed Bit Rate (GBR) to a SPI value selected for streaming NBR - Nominal Bit Rate (NBR) to Interactive traffic classes
For internal use 61 Nokia Siemens Networks
MHA type: Other the BTS doesnt provide DC power to MHA, nor generates MHA alarm MHA power supply has to be fed from an external source UL/DL Delay in the MHA can be user-defined
NOKIA MHAs: WMHA Single MHA WMHB 2 single MHAs, separate power feed WMHC Dual MHA, single power feed through its BTS2 port.
for WMHC/WMHD only the WMHC/WMHD requires power supply through its BTS2 port. This selection is made for the FRxx ANT port which is connected it.
for WMHC/WMHD only If an additional equipment behind the MHA requires power supply through antenna feeder, the voltage can be defined by the user or automatically set by the BTS.
for all MHA types the existence if Diplexers/Triplexers is to be defined for two reasons: - the additional loss is to be considered by the BTS for correct signal gain. - the additional delay affects the round trip time
for all MHA types - the number of Diplexers/Triplexers is to be defined: 1: X-plexer on BTS side only, wideband antenna 2: X-plexer on both sides, BTS and antenna 3: With broadband antenna and MHAs
TMA Support
FRGJ Dual Radio Module with Siemens TMA support FRGK Single Radio Module with Siemens TMA support FRGF Triple Radio Module with Siemens TMA support
For internal use 72 Nokia Siemens Networks Presentation / Author / Date
TMA Support
FSMD System Module with two FSPs: FSP1: 192.168.255.33 FSP3: 192.168.255.35
During the test the BTS transmits at nearly full power. Make sure that there is an antenna connected to the antenna connector
WCDMA Loop Tests are not executed on reserved DSPs. DSPs can be reserved for Common Channels or for HSPA. FSP1: DSP1 reserved for Common Channels FSP3: DSP1 and DSP2 reserved for HSDPA
For internal use 92 Nokia Siemens Networks Presentation / Author / Date
Number of Not Executed WCDMA Loop Tests is changed due to the changed HSPA configuration.
For internal use 93 Nokia Siemens Networks Presentation / Author / Date
Commissioning FTM for I-HSPA Commissioning FTM for I-HSPA (IP over ATM)
In the Commissioning - Site Properties page, define the identification information, IP addresses and common configuration options
Defining physical layer configuration physical interfaces, synchronization and IMA groups
At least five traffic descriptors are needed: one for each Iu-PS/Iur termination (Iu-PS Control Plane, Iu-PS User Plane, Iur Control Plane, and Iur User Plane) and one for the DCN interface.
The destination address is the IP address of the remote node to which the DCN interface is connected. The supported format is IPv4
2. Select the commissioning target by clicking the appropriate option: BTS Site, BTS Only or TRS Only. 3. Select the Template option. 4. Select the commissioning file. 5. Click the Next button.
For internal use 116 Nokia Siemens Networks Presentation / Author / Date