Professional Documents
Culture Documents
Lab 1
Lab 1
All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 1 of 26
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
Learning Objectives
To complete this lab: Cable a network according to the topology diagram. Erase the startup configuration and reload a router to the default state. Perform basic configuration tasks on a router. Configure and activate interfaces. Configure Spanning Tree Protocol. Configure VTP servers and client. Configure VLANS on the switches. Configure RIP routing on all the routers. Configure OSPF routing on all routers. Configure EIGRP routing on all the routers.
Scenario
In this lab, you will review basic routing and switching concepts. Try to do as much on your own as possible. Refer back to previous material when you cannot proceed on your own. Note: Configuring three separate routing protocolsRIP, OSPF, and EIGRPto route the same network is emphatically not a best practice. It should be considered a worst practice and is not something that would be done in a production network. It is done here so that you can review the major routing protocols before proceeding, and see a clear illustration of the concept of administrative distance.
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
Configure the following message-of-the-day banner: Unauthorized access strictly prohibited and prosecuted to the full extent of the law". Configure a password for console connections. Configure synchronous logging. Configure a password for vty connections. Save the running configuration to NVRAM. Router Configurations enable configure terminal no ip domain-lookup enable secret class banner motd ^CUnauthorized access strictly prohibited and prosecuted to the full extent of the law^C ! ! line con 0 exec-timeout 0 0 logging synchronous password cisco login ! line vty 0 4 password cisco login end copy running-config startup-config Switch Configurations enable configure terminal no ip domain-lookup enable secret class banner motd ^CUnauthorized access strictly prohibited and prosecuted to the full extent of the law^C ! ! line con 0 exec-timeout 0 0 logging synchronous password cisco login ! line vty 0 15 password cisco login end copy running-config startup-config
All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 3 of 26
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
interface FastEthernet0/1.13 encapsulation dot1Q 13 ip address 10.13.13.3 255.255.255.0 ! interface FastEthernet0/1.30 encapsulation dot1Q 30 ip address 192.168.30.1 255.255.255.0 ! interface Serial0/0/1 ip address 10.2.2.2 255.255.255.252 no shutdown ! Step 2: Verify IP addressing and interfaces. R1#show ip interface brief Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES unset up up FastEthernet0/1.10 192.168.10.1 YES manual up up FastEthernet0/1.12 10.12.12.1 YES manual up up FastEthernet0/1.13 10.13.13.1 YES manual up up Serial0/0/0 10.1.1.1 YES unset up up Serial0/0/1 unassigned YES unset administratively down down Serial0/1/0 unassigned YES unset administratively down down Serial0/1/1 unassigned YES unset administratively down down R2#show ip interface brief Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES manual up up FastEthernet0/1.12 10.12.12.2 YES manual up up FastEthernet0/1.20 192.168.20.1 YES manual up up Serial0/0/0 10.1.1.2 YES manual up up Serial0/0/1 10.2.2.1 YES manual up up R3#show ip interface brief Interface IP-Address OK? Method Status Protocol FastEthernet0/0 unassigned YES unset administratively down down FastEthernet0/1 unassigned YES manual up up FastEthernet0/1.13 10.13.13.3 YES manual up up FastEthernet0/1.30 192.168.30.1 YES manual up up Serial0/0/0 unassigned YES unset administratively down down Serial0/0/1 10.2.2.2 YES manual up up Step 3: Configure the Management VLAN interface on S1, S2, and S3. S1(config)#interface vlan10 S1(config-if)#ip address 192.168.10.2 255.255.255.0 S2(config)#interface vlan20 S2(config-if)#ip address 192.168.20.2 255.255.255.0 S3(config)#interface vlan30
All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 5 of 26
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
S3(config-if)#ip address 192.168.30.2 255.255.255.0 Step 4: Configure the PC1 and PC3 Ethernet interfaces. Step 5: Test connectivity between the PCs.
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
Setting device to VTP CLIENT mode S3(config)#vtp domain cisco Changing VTP domain name from NULL to cisco S3(config)#vtp password cisco Setting device VLAN database password to cisco Step 3: Verify the configuration. S1#show vtp status VTP Version : 2 Configuration Revision : 0 Maximum VLANs supported locally : 255 Number of existing VLANs : 5 VTP Operating Mode : Server VTP Domain Name : cisco VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0x97 0xB7 0xCF 0xD2 0xDD 0x77 0x88 0x34 Configuration last modified by 0.0.0.0 at 3-1-93 00:25:29 Local updater ID is 192.168.10.2 on interface Vl10 (lowest numbered VLAN interface found) S2#show vtp status VTP Version : 2 Configuration Revision : 0 Maximum VLANs supported locally : 255 Number of existing VLANs : 5 VTP Operating Mode : Client VTP Domain Name : cisco VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0xE7 0xD7 0x24 0xC0 0x33 0x80 0xF7 0xAA Configuration last modified by 0.0.0.0 at 3-1-93 00:19:03 S3#show vtp status VTP Version : 2 Configuration Revision : 0 Maximum VLANs supported locally : 255 Number of existing VLANs : 5 VTP Operating Mode : Client VTP Domain Name : cisco VTP Pruning Mode : Disabled VTP V2 Mode : Disabled VTP Traps Generation : Disabled MD5 digest : 0xE7 0xD7 0x24 0xC0 0x33 0x80 0xF7 0xAA Configuration last modified by 0.0.0.0 at 3-1-93 06:52:33
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
Step 2: Verify that S2 and S3 received VLAN configurations from S1. S1#show vlan brief VLAN Name Status Ports ---- -------------------------------1 default active Fa0/2, Fa0/3, Fa0/4, Fa0/6, Fa0/7, Fa0/8, Fa0/9 Fa0/10, Fa0/11, Fa0/12,Fa0/13 Fa0/14, Fa0/15, Fa0/16,Fa0/17 Fa0/18, Fa0/19, Fa0/20,Fa0/21 Fa0/22, Fa0/23, Fa0/24 10 VLAN0010 active 12 VLAN0012 active 13 VLAN0013 active 20 VLAN0020 active 30 VLAN0030 active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup S2#show vlan brief VLAN Name Status Ports ---- -------------------------------1 default active Fa0/2, Fa0/3, Fa0/4, Fa0/6, Fa0/7, Fa0/8, Fa0/9 Fa0/10, Fa0/11, Fa0/12,Fa0/13 Fa0/14, Fa0/15, Fa0/16,Fa0/17 Fa0/18, Fa0/19, Fa0/20,Fa0/21 Fa0/22, Fa0/23, Fa0/24, Gi0/2 10 VLAN0010 active 12 VLAN0012 active 13 VLAN0013 active 20 VLAN0020 active 30 VLAN0030 active 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup S3#show vlan brief VLAN Name Status Ports ---- -------------------------------1 default active Fa0/2, Fa0/3, Fa0/4, Fa0/6, Fa0/7, Fa0/8, Fa0/9 Fa0/10, Fa0/11, Fa0/12,Fa0/13 Fa0/14, Fa0/15, Fa0/16,Fa0/17 Fa0/18, Fa0/19, Fa0/20,Fa0/21 Fa0/22, Fa0/23, Fa0/24, Gi0/2 10 VLAN0010 active 12 VLAN0012 active 13 VLAN0013 active 20 VLAN0020 active 30 VLAN0030 active
--------- ----------------------------Fa0/5
--------- ----------------------------Fa0/5
--------- ----------------------------Fa0/5
All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 8 of 26
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
Step 3: Assign ports to the appropriate VLANs. S1: interface FastEthernet0/1 switchport trunk allowed vlan 10,12,13 switchport mode trunk ! interface FastEthernet0/2 switchport access vlan 10 switchport mode access ! interface GigabitEthernet0/1 switchport trunk allowed vlan 1,12 switchport mode trunk ! interface GigabitEthernet0/2 switchport trunk allowed vlan 1,13 switchport mode trunk ! S2: interface FastEthernet0/1 switchport trunk allowed vlan 12,20 switchport mode trunk ! interface FastEthernet0/2 switchport access vlan 20 switchport mode access ! interface GigabitEthernet0/1 switchport trunk allowed vlan 12 switchport mode trunk ! S3: interface FastEthernet0/1 switchport trunk allowed vlan 13,30 switchport mode trunk ! interface FastEthernet0/2 switchport access vlan 30 switchport mode access ! interface GigabitEthernet0/1 switchport trunk allowed vlan 13 switchport mode trunk !
All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 9 of 26
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
ms
ms
ms
ms
All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 10 of 26
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
R1#ping 10.13.13.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.13.13.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R1#ping 192.168.10.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.10.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R1#ping 192.168.10.10 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.10.10, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R1#ping 192.168.20.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.20.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R1#ping 192.168.20.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.20.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R1#ping 192.168.30.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.30.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R1#ping 192.168.30.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.30.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R1#ping 192.168.30.10 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.30.10, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R2: R2#ping 10.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.1.1., timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms
All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 11 of 26
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
R2#ping 10.2.2.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.2.2.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R2#ping 10.12.12.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.12.12.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R2#ping 10.13.13.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.13.13.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R2#ping 10.13.13.3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.13.13.3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R2#ping 192.168.10.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.10.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R2#ping 192.168.10.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.10.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R2#ping 192.168.10.10 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.10.10, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R3#ping 192.168.20.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.20.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R2#ping 192.168.30.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.30.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R2#ping 192.168.30.2 Type escape sequence to abort.
All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 12 of 26
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
Sending 5, 100-byte ICMP Echos to 192.168.30.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R2#ping 192.168.30.10 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.30.10, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R3: R3#ping 10.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.1.1.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R3#ping 10.1.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.1.1.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R3#ping 10.2.2.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.2.2.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R3#ping 10.12.12.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.12.12.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R3#ping 10.12.12.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.12.12.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R3#ping 10.13.13.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.13.13.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R3#ping 192.168.10.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.10.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R3#ping 192.168.10.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.10.2, timeout is 2 seconds:
All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 13 of 26
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
!!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R3#ping 192.168.10.10 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.10.10, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R3#ping 192.168.20.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.20.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R3#ping 192.168.20.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.20.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R3#ping 192.168.30.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.30.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms R3#ping 192.168.30.10 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.30.10, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 28/28/28 ms Step 3: Verify the routing table. R1#show ip route <output omitted> R 192.168.30.0/24 [120/1] via 10.13.13.3, 00:00:03, FastEthernet0/1.13 C 192.168.10.0/24 is directly connected, FastEthernet0/1.10 R 192.168.20.0/24 [120/1] via 10.12.12.2, 00:00:00, FastEthernet0/1.12 [120/1] via 10.1.1.2, 00:00:13, Serial0/0/0 10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks C 10.13.13.0/24 is directly connected, FastEthernet0/1.13 C 10.12.12.0/24 is directly connected, FastEthernet0/1.12 R 10.2.2.0/30 [120/1] via 10.13.13.3, 00:00:03, FastEthernet0/1.13 [120/1] via 10.12.12.2, 00:00:00, FastEthernet0/1.12 [120/1] via 10.1.1.2, 00:00:13, Serial0/0/0 C 10.1.1.0/30 is directly connected, Serial0/0/0 R2#show ip route <output omitted> Gateway of last resort is not set
All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 14 of 26
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
R 192.168.30.0/24 [120/1] via 10.2.2.2, 00:00:05, Serial0/0/1 R 192.168.10.0/24 [120/1] via 10.12.12.1, 00:00:17, FastEthernet0/1.12 [120/1] via 10.1.1.1, 00:00:17, Serial0/0/0 C 192.168.20.0/24 is directly connected, FastEthernet0/1.20 10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks R 10.13.13.0/24 [120/1] via 10.12.12.1, 00:00:17, FastEthernet0/1.12 [120/1] via 10.2.2.2, 00:00:05, Serial0/0/1 [120/1] via 10.1.1.1, 00:00:17, Serial0/0/0 C 10.12.12.0/24 is directly connected, FastEthernet0/1.12 C 10.2.2.0/30 is directly connected, Serial0/0/1 C 10.1.1.0/30 is directly connected, Serial0/0/0 R3#show ip route <output omitted> Gateway of last resort is not set C 192.168.30.0/24 is directly connected, FastEthernet0/1.30 R 192.168.10.0/24 [120/1] via 10.13.13.1, 00:00:08, FastEthernet0/1.13 R 192.168.20.0/24 [120/1] via 10.2.2.1, 00:00:10, Serial0/0/1 10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks C 10.13.13.0/24 is directly connected, FastEthernet0/1.13 R 10.12.12.0/24 [120/1] via 10.13.13.1, 00:00:08, FastEthernet0/1.13 [120/1] via 10.2.2.1, 00:00:10, Serial0/0/1 C 10.2.2.0/30 is directly connected, Serial0/0/1 R 10.1.1.0/30 [120/1] via 10.13.13.1, 00:00:08, FastEthernet0/1.13 [120/1] via 10.2.2.1, 00:00:10, Serial0/0/1
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
network 192.168.30.0 0.0.0.255 area 0 ! Step 2: Verify that OSPF routes have replaced RIP routes because of lower administrative distance. R1#show ip route <output omitted> O 192.168.30.0/24 [110/2] via 10.13.13.3, 00:00:13, FastEthernet0/1.13 C 192.168.10.0/24 is directly connected, FastEthernet0/1.10 O 192.168.20.0/24 [110/2] via 10.12.12.2, 00:00:13, FastEthernet0/1.12 10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks C 10.13.13.0/24 is directly connected, FastEthernet0/1.13 C 10.12.12.0/24 is directly connected, FastEthernet0/1.12 O 10.2.2.0/30 [110/782] via 10.13.13.3, 00:00:13, FastEthernet0/1.13 [110/782] via 10.12.12.2, 00:00:13, FastEthernet0/1.12 C 10.1.1.0/30 is directly connected, Serial0/0/0 R2#show ip route <output omitted> O 192.168.30.0/24 [110/3] via 10.12.12.1, 00:00:39, FastEthernet0/1.12 O 192.168.10.0/24 [110/2] via 10.12.12.1, 00:00:39, FastEthernet0/1.12 C 192.168.20.0/24 is directly connected, FastEthernet0/1.20 10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks O 10.13.13.0/24 [110/2] via 10.12.12.1, 00:00:39, FastEthernet0/1.12 C 10.12.12.0/24 is directly connected, FastEthernet0/1.12 C 10.2.2.0/30 is directly connected, Serial0/0/1 C 10.1.1.0/30 is directly connected, Serial0/0/0 R3#show ip route <output omitted> C 192.168.30.0/24 is directly connected, FastEthernet0/0.30 O 192.168.10.0/24 [110/2] via 10.13.13.1, 00:01:03, FastEthernet0/1.13 O 192.168.20.0/24 [110/3] via 10.13.13.1, 00:01:03, FastEthernet0/1.13 10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks C 10.13.13.0/24 is directly connected, FastEthernet0/1.13 O 10.12.12.0/24 [110/2] via 10.13.13.1, 00:01:03, FastEthernet0/1.13 C 10.2.2.0/30 is directly connected, Serial0/0/1 O 10.1.1.0/30 [110/782] via 10.13.13.1, 00:01:03, FastEthernet0/1.13 How are the routing decisions different now that OSPF is running?
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
Step 3: Verify that RIP is still running. R1#show ip rip database 10.0.0.0/8 auto-summary 10.1.1.0/30 directly connected, Serial0/0/0 10.12.12.0/24 directly connected, FastEthernet0/1.12 10.13.13.0/24 directly connected, FastEthernet0/1.13 192.168.10.0/24 auto-summary 192.168.10.0/24 directly connected, FastEthernet0/1.10 R2#show ip rip database 10.0.0.0/8 auto-summary 10.1.1.0/30 directly connected, Serial0/0/0 10.2.2.0/30 directly connected, Serial0/0/1 10.12.12.0/24 directly connected, FastEthernet0/1.12 192.168.20.0/24 auto-summary 192.168.20.0/24 directly connected, FastEthernet0/1.20 R3#show ip rip database 10.0.0.0/8 auto-summary 10.2.2.0/30 directly connected, Serial0/0/1 10.13.13.0/24 directly connected, FastEthernet0/1.13 192.168.30.0/24 auto-summary 192.168.30.0/24 directly connected, FastEthernet0/1.30
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
! Step 2: Verify that EIGRP routes have replaced OSPF routes because of lower administrative distance. R1#show ip route <output omitted> D 192.168.30.0/24 [90/30720] via 10.13.13.3, 00:00:24, FastEthernet0/1.13 C 192.168.10.0/24 is directly connected, FastEthernet0/1.10 D 192.168.20.0/24 [90/30720] via 10.12.12.2, 00:00:48, FastEthernet0/1.12 10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks C 10.13.13.0/24 is directly connected, FastEthernet0/1.13 C 10.12.12.0/24 is directly connected, FastEthernet0/1.12 D 10.2.2.0/30 [90/20514560] via 10.13.13.3, 00:00:24, FastEthernet0/1.13 [90/20514560] via 10.12.12.2, 00:00:24, FastEthernet0/1.12 C 10.1.1.0/30 is directly connected, Serial0/0/0 R2#show ip route <output omitted> D 192.168.30.0/24 [90/33280] via 10.12.12.1, 00:00:29, FastEthernet0/1.12 D 192.168.10.0/24 [90/30720] via 10.12.12.1, 00:00:30, FastEthernet0/1.12 C 192.168.20.0/24 is directly connected, FastEthernet0/1.20 10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks D 10.13.13.0/24 [90/30720] via 10.12.12.1, 00:00:30, FastEthernet0/1.12 C 10.12.12.0/24 is directly connected, FastEthernet0/1.12 C 10.2.2.0/30 is directly connected, Serial0/0/1 C 10.1.1.0/30 is directly connected, Serial0/0/0 R3#show ip route <output omitted> C 192.168.30.0/24 is directly connected, FastEthernet0/0.30 D 192.168.10.0/24 [90/30720] via 10.13.13.1, 00:00:08, FastEthernet0/1.13 D 192.168.20.0/24 [90/33280] via 10.13.13.1, 00:00:08, FastEthernet0/1.13 10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks C 10.13.13.0/24 is directly connected, FastEthernet0/1.13 D 10.12.12.0/24 [90/30720] via 10.13.13.1, 00:00:08, FastEthernet0/1.13 C 10.2.2.0/30 is directly connected, Serial0/0/1 D 10.1.1.0/30 [90/20514560] via 10.13.13.1, 00:00:08, FastEthernet0/0.13 Step 3: Verify that OSPF is still running. R1#show ip ospf database OSPF Router with ID (192.168.10.1) (Process ID 1) Router Link States (Area 0) Link ID ADV Router Age Seq# Checksum Link count 192.168.10.1 192.168.10.1 1038 0x80000005 0x0056F6 5 192.168.20.1 192.168.20.1 1039 0x80000004 0x00B9F7 6 192.168.30.1 192.168.30.1 1048 0x80000003 0x00C99A 4 Net Link States (Area 0)
All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 18 of 26
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
Link ID ADV Router Age Seq# Checksum 10.12.12.1 192.168.20.1 1039 0x80000001 0x004D5A 10.13.13.1 192.168.10.1 1052 0x80000001 0x003175 R2#show ip ospf database OSPF Router with ID (192.168.20.1) (Process ID 1) Router Link States (Area 0) Link ID ADV Router Age Seq# Checksum Link count 192.168.10.1 192.168.10.1 1084 0x80000005 0x0056F6 5 192.168.20.1 192.168.20.1 1083 0x80000004 0x00B9F7 6 192.168.30.1 192.168.30.1 1092 0x80000003 0x00C99A 4 Net Link States (Area 0) Link ID ADV Router Age Seq# Checksum 10.12.12.1 192.168.20.1 1083 0x80000001 0x004D5A 10.13.13.1 192.168.10.1 1098 0x80000001 0x003175 R3#show ip ospf database OSPF Router with ID (192.168.30.1) (Process ID 1) Router Link States (Area 0) Link ID ADV Router Age Seq# Checksum Link count 192.168.10.1 192.168.10.1 1135 0x80000005 0x0056F6 5 192.168.20.1 192.168.20.1 1135 0x80000004 0x00B9F7 6 192.168.30.1 192.168.30.1 1143 0x80000003 0x00C99A 4 Net Link States (Area 0) Link ID ADV Router Age Seq# Checksum 10.12.12.1 192.168.20.1 1136 0x80000001 0x004D5A 10.13.13.1 192.168.10.1 1149 0x80000001 0x003175
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
no ip address no shutdown ! interface FastEthernet0/1.10 encapsulation dot1Q 10 ip address 192.168.10.1 255.255.255.0 ! interface FastEthernet0/1.12 encapsulation dot1Q 12 ip address 10.12.12.1 255.255.255.0 ! interface FastEthernet0/1.13 encapsulation dot1Q 13 ip address 10.13.13.1 255.255.255.0 ! interface Serial0/0/0 ip address 10.1.1.1 255.255.255.0 no fair-queue clockrate 64000 no shutdown ! interface Serial0/0/1 no ip address shutdown ! router eigrp 10 network 10.1.1.0 0.0.0.3 network 10.12.12.0 0.0.0.255 network 10.13.13.0 0.0.0.255 network 192.168.10.0 no auto-summary ! router ospf 1 log-adjacency-changes network 10.1.1.0 0.0.0.3 area 0 network 10.12.12.0 0.0.0.255 area 0 network 10.13.13.0 0.0.0.255 area 0 network 192.168.10.0 0.0.0.255 area 0 ! router rip version 2 network 10.0.0.0 network 192.168.10.0 no auto-summary !! ! banner motd ^CUnauthorized access strictly prohibited and prosecuted to the full extent of the law^C !
All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 20 of 26
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
line con 0 exec-timeout 0 0 password cisco logging synchronous login line aux 0 line vty 0 4 password cisco login ! end R2 R2#show run !<output omitted> ! hostname R2 ! enable secret class ! no ip domain lookup ! interface FastEthernet0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address no shutdown ! interface FastEthernet0/1.20 encapsulation dot1Q 20 ip address 192.168.20.1 255.255.255.0 ! interface FastEthernet0/1.12 encapsulation dot1Q 12 ip address 10.12.12.2 255.255.255.0 ! interface Serial0/0/0 ip address 10.1.1.2 255.255.255.252 no shutdown ! interface Serial0/0/1 ip address 10.2.2.1 255.255.255.252 no shutdown ! router eigrp 10 network 10.1.1.0 0.0.0.3 network 10.2.2.0 0.0.0.3 network 10.12.12.0 0.0.0.255 network 192.168.20.0 no auto-summary !
All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 21 of 26
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
router ospf 1 log-adjacency-changes network 10.1.1.0 0.0.0.3 area 0 network 10.2.2.0 0.0.0.3 area 0 network 10.12.12.0 0.0.0.255 area 0 network 192.168.20.0 0.0.0.255 area 0 ! router rip version 2 network 10.0.0.0 network 192.168.20.0 no auto-summary ! banner motd ^CUnauthorized access strictly prohibited and prosecuted to the full extent of the law^C ! line con 0 exec-timeout 0 0 password cisco logging synchronous login line aux 0 line vty 0 4 password cisco login ! end R3 R3#show run !<output omitted> ! hostname R3 ! ! enable secret class ! no ip domain lookup ! ! interface FastEthernet0/0 no ip address shutdown ! interface FastEthernet0/1 no ip address no shutdown ! interface FastEthernet0/1.13 encapsulation dot1Q 13 ip address 10.13.13.3 255.255.255.0 !
All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 22 of 26
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
interface FastEthernet0/1.30 encapsulation dot1Q 30 ip address 192.168.30.1 255.255.255.0 ! interface Serial0/0/0 no ip address shutdown clockrate 125000 ! interface Serial0/0/1 ip address 10.2.2.2 255.255.255.252 no shutdown ! router eigrp 10 network 10.2.2.0 0.0.0.3 network 10.13.13.0 0.0.0.255 network 192.168.30.0 no auto-summary ! router ospf 1 network 10.2.2.0 0.0.0.3 area 0 network 10.13.13.0 0.0.0.255 area 0 network 192.168.30.0 0.0.0.255 area 0 ! router rip version 2 network 10.0.0.0 network 192.168.30.0 no auto-summary ! banner motd ^CCUnauthorized access strictly prohibited and prosecuted to the full extent of the law^C ! line con 0 exec-timeout 0 0 password cisco logging synchronous login line aux 0 line vty 0 4 password cisco login ! End S1 S1#show run !<output omitted> ! hostname S1 ! ! enable secret class !
All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 23 of 26
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
no ip domain lookup ! vlan 10,12,13,20,30 ! spanning-tree mode pvst spanning-tree extend system-id spanning-tree vlan 1-1000 priority 24576 ! vtp mode server vtp domain cisco vtp password cisco ! interface FastEthernet0/1 switchport trunk allowed vlan 10,12,13 switchport mode trunk ! interface FastEthernet0/2 switchport access vlan 10 swotchport mode access ! interface GigabitEthernet0/1 switchport trunk allowed vlan 12 switchport mode trunk ! interface GigabitEthernet0/2 switchport trunk allowed vlan 13 switchport mode trunk ! interface vlan10 ip address 192.168.10.2 255.255.255.0 ! banner motd ^CUnauthorized access strictly prohibited and prosecuted to the full extent of the law^C ! line con 0 exec-timeout 0 0 password cisco logging synchronous login line aux 0 line vty 0 15 password cisco login ! End S2 S2#show run !<output omitted> hostname S2 ! enable secret class !
All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 24 of 26
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
no ip domain lookup ! spanning-tree mode pvst spanning-tree extend system-id ! vtp mode client vtp domain cisco vtp password cisco ! interface FastEthernet0/1 switchport trunk allowed vlan 12,20 switchport mode trunk ! interface FastEthernet0/2 switchport access vlan 20 swotchport mode access ! interface GigabitEthernet0/1 switchport trunk allowed vlan 12 switchport mode trunk ! interface vlan20 ip address 192.168.20.2 255.255.255.0 ! banner motd ^CCUnauthorized access strictly prohibited and prosecuted to the full extent of the law^C ! line con 0 exec-timeout 0 0 password cisco logging synchronous login line aux 0 line vty 0 15 password cisco login ! End S3 S3#show run !<output omitted> ! hostname S3 ! enable secret class ! no ip domain lookup ! ! spanning-tree mode pvst spanning-tree extend system-id ! !
All contents are Copyright 19922007 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 25 of 26
CCNA Exploration Accessing the WAN: Introduction to WANs Lab 1.4.1: Challenge Review
vtp mode client vtp domain cisco vtp password cisco ! interface FastEthernet0/1 switchport trunk allowed vlan 13,30 switchport mode trunk ! interface FastEthernet0/2 switchport access vlan 30 swotchport mode access ! interface GigabitEthernet0/1 switchport trunk allowed vlan 13 switchport mode trunk interface vlan30 ip address 192.168.30.2 255.255.255.0 ! banner motd ^CCUnauthorized access strictly prohibited and prosecuted to the full extent of the law^C ! line con 0 exec-timeout 0 0 password cisco logging synchronous login line aux 0 line vty 0 15 password cisco login ! end