STEREO POWER AMPLIFI R service MANUAL - parts LIST - MECHANISM / CHASSIS. CHECK that all exposed conductive surfaces are properly insulated from supply circuits. Meter impedanc e should be equivalent to 1500 ohm shunted by O.15.uF. Leakage current must not exceed O.5mA.
STEREO POWER AMPLIFI R service MANUAL - parts LIST - MECHANISM / CHASSIS. CHECK that all exposed conductive surfaces are properly insulated from supply circuits. Meter impedanc e should be equivalent to 1500 ohm shunted by O.15.uF. Leakage current must not exceed O.5mA.
STEREO POWER AMPLIFI R service MANUAL - parts LIST - MECHANISM / CHASSIS. CHECK that all exposed conductive surfaces are properly insulated from supply circuits. Meter impedanc e should be equivalent to 1500 ohm shunted by O.15.uF. Leakage current must not exceed O.5mA.
STEREO POWER AMPLIFIER
M-60
SERV NONE YE
WTO SERVICE PERSONNEL
1.Critieal Components Information,
Components having special characteristics are marked /\ and must be replaced with parts having
specifications equal to those originally installed
2, Leakage Current Measurement(For 120V Model Only).
When service has been completed, it is imperative that you verify that all exposed conductive su
rfaces are properly insulated from supply circuits
@Meter impedance should be equivalent to 1500 ohm shunted by 0.15.F
@ Leakage current must not exceed 0,5mA. EQUIPMENT. see TR
@Be sure to test for leakage with UNDER TEST Of EQUIVALENT
AC plug in both polarities O
A
Wal
Outer
CONTENTS
REAR PANEL 1 P.C. BOARD ~MAIN 6
BLOCK DIAGRAM 2 SCHEMATIC DIAGRAM~MAIN 8
SPECIFICATIONS 2 SCHEMATIC DIAGRAM~METER: g
INTERNAL VIEW: 3 WIRING DIAGRAM 9
DISASSEMBLY INSTRUCTIONS: 3. PARTS LIST~ ELECTRIC. 10
ADJUSTMENTS 4 EXPLOADED VIEW~MECHANISM/CHASSIS 14
P.C, BOARD ~METER 5 PARTS LIST~MECHANISM/CHASSIS 16
ras w= @ YAMAHA
2.64-781 @ Printod in Jepan 84.7M-60
INTERNAL VIEW
@® Power Transformer
@ Electrolytic Cap
@® Main P.C.B.
@ Meter P.C.B.
@ Heat Sink
ADJUSTMENTS
Before Adjustments
@ Wait 2 minutes after power-ON to stabilize ampli
@Make sure that the main volume is minimum and set Auto-A switch to OFF.
step] Adjustments | Location | E28 ene |
r operation.
Test point Value
| ‘Across emitter resistor(0.229) of
VR103{L-ch,) | D.C. V-meter | power transistor.
1 | Idling adjustment / ya194(R-ch.) | Digtal tester | R153,R155(L-ch.) ey
} R154,R156(R-ch.)
2. | Auto-A operation | Check that the voltage at each test point stated above
confirmation | increases when Auto-A switch is turned on. 10£10mv
Meter Level | VR501(L-ch.)
(1) Set the load level of the meter at 22 position.
3 (2) Adjust VR501 and VR502 so that OdB of the meter lights
|__ adjustment | VR502(R-ch.)| "Wp when the output is f=1KHz and V=34.5V.
Mower 6.8.
Main C8
_vrso1tu) vasoain)
Tost Point) Test Point ®)
@vatos — vmsosiF
MOF! oe S20 Ree
seri oe so eg om | |e
o.oe7
teh
25 o.atn
4
zaxaes | 2soia73 | aseseo | asarz0s | _asisss o5r820
zsezse1 | iStaes tseees
gscaiez | 152079
ee
i moagens
a , 2 Jarno 5"
oe ae te onl ae
zearsoe | 2saivas | asas7o zeciess | wane
ascezes | 2sczvos | aeators zscazse | wriea
Bate tetas
eatin deceese | HEEL goog
2 ae
oe .
Se . %
. = £ CATHODE= 1 = 1 =. 7
M84) E(SCHEMATIC DIAGRAM~MAIN)M-60
Hid
Components having special churectaristis are Marked. A,
tind munt be relaced with prt ving spctertone otal
{o tow erin tallod.|
+ Al votge ae manned with 2 OMI DC elec vl mete
Schematic dogam subject change without moiRP
Confirmation of the voltage switching operation. Output wave
Terminals output )W (load is 80).
Check that the LP and +RP
m below.
terminals chang
Weve form at-LP and—RP
~ ! 3 | £ i D
PRINTED CIRCUIT BOARD PATTERN SIDE~METER CIRCUIT BOARDight
Inpet
mato a
Speakers
M-60 M
PRINTED CIRCUT BOARD PATTERN SIDE~MAIN CIRCUIT BOARD
o oO
-
5 a i
TT
at
a as ea
OA | O Lo.
: ke
:
=
e
inOo
oO