Professional Documents
Culture Documents
11ak36 Tech Bulletins
11ak36 Tech Bulletins
START DATE : 14.03.2002 REASONS OF CHANGE: FOR SMPS IC POSITION IC 841 OF CHASSIS 11AK36 , IC FROM DIFFERENT SUPPLIER ARE USED . TO SET THE SAME WORKING FREQUENCY OF APPROX. 50 KHZ FOR ALL SUPPLIERS , SOME VALUES OF SOME COMPONENTS ARE DIFFERENT . THE TABLE BELOW SHOWS ALL USED ICS WITH PRINT OF THEM AND THE VALUE OF THE OPTIONAL COMPONENTS .
COMPANY
HI30000531 RES CF 1/4W 15K J SINCERITY ON-SEMI KEC ST UTC HUA-JING 30000531 RES CF 1/4W 15K J N.C. 30000770 RES CF 1/4W 680R 30000770 RES CF 1/4W 680R 30000770 RES CF 1/4W 680R
H 3842 P
CAP MKT 2.2NF 63V J CAP MKT 27nF 100V J CAP MKT 33nF 100V J CAP MKT 33nF 100V J CAP MKT 33nF 100V J
NO 1 2 3 NO 1 2 3
PCB CODE
VESTEL CODE
COMPONENT NAME
POSITION NUMBER
QUANTITY
PCB CODE
VESTEL CODE
IN COMPONENT NAME
POSITION NUMBER
QUANTITY
QUALITY MANAGER
NO 1 2 3 4 5 6
PCB CODE
AK36
VESTEL CODE
30016654 30000345 30000531 30001158 30000088 30000673
POSITION NUMBER
C810 C811 R804 R810 C807 R807
QUANTITY
1 1 1 1 1 1
NO 1 2 3 4 5 6
PCB CODE
AK36
VESTEL CODE
30016126 30000387 30000770 30000096 30001173 30006754
IN COMPONENT NAME
CAP SMD 220NF 16V K R (0603) CAP EL 33 UF 50 V M RES CF 1/4 W 680R J CAP MKT 27NF 100V J RES MO 1W 0.47R J RES MO 2W 120K J
POSITION NUMBER
C810 C811 R804 C807 R810 R807
QUANTITY
1 1 1 1 1 1
Form Rev.No:00
Katod of D703
Smd 1k (note 1 )
Service Bulletin
Model:
with
AK36
Priority ( )S. All products. ( )A. Items in Customer / Dealer stock / Service return goods. ( )B. Customer stock / Units returned for Service. ( X)C. Sold items returned for Service. ( )D. Only Units returned to this bulletin. ( )E. Others
SUBJECT :
<Objective>
Please modify if following symptom occurs
<Symptom>
While TV is switching to st-by off, the st-by led is blinking in a short time.
<Cause>
The negative peaks between the anode and cathode of the Thyristor.
<Countermeasures>
Apply that modification: CHANGE Q601 THEN, Replace; R804: RES CF 1/4W 15K J RES CF 1/4W 1K J R805: RES CF 1/4W 1K J RES CF 1/4W 470R J C807: CAP MKP 2.2 NF 63V J CAP MKP 22 NF 100V J Connect a RES SMD 1/16W 22K J between the base and collector of q601.
Service Bulletin
Model:
with
AK36
Priority ( )S. All products. ( )A. Items in Customer / Dealer stock / Service return goods. ( )B. Customer stock / Units returned for Service. ( X)C. Sold items returned for Service. ( )D. Only Units returned to this bulletin. ( )E. Others
SUBJECT :
IC404 DEFECT
<Objective>
Please modify if following symptom occurs
<Symptom>
While TV is switching to ON, there is no audio.
<Cause>
The over voltage stress on the IC404.
<Countermeasures>
Apply that modification: CHANGE IC401 THEN, Replace; J188: JUMBER WIRE RES FUSE W 0.33R J
Service Bulletin
Model: AK36 and AK46 chassis with TP46I-3 CRT board
Priority ( )S. All product. ( )A. Items in Customer / Dealer stock / Service return goods. ( )B. Customer stock / Units returned for Service. ( X)C. Sold items returned for Service. ( )D. Only Units returned to this bulletin. ( )E. Others
SUBJECT :
IC403(STV224X) defects
<Objective>
Please modify if following symptom occurs.
<Symptom>
1. No picture after switching on due to the IC403 RGB outputs are defected. 2. When the picture is only green due to 20. Pin of IC403 CVBS SW pin) is defected. 3. When Picture is vertically shifted
<Cause>
1. Spark on CRT 2. No good grounding on Tuner 3. Base and emitter of Q603 is short circuit.
<Countermeasures>
After changing the defected IC403, the following modifications to repair chassis and prevent reoccurence of defects 1. Modifty TP46I-3 CRT board by insertion BA159 diode between 200V and RGB driver resistors as explain below. Solder the anode of Diode BA159 (VE-30001318) to cathode of D902; solder the cathode of Diode BA159 to Q909 collector (intersection point with R913). Solder the anode of Diode BA159 (VE-30001318) to cathode of D903; solder the cathode of Diode BA159 to Q908 collector (intersection point with R914). Solder the anode of Diode BA159 (VE-30001318) to cathode of D901; solder the cathode of Diode BA159 to Q907 collector (intersection point with R915). 2. Connect a Diode zener 8.2V (VE-30001347) between the Emitter of Q2 ( - point of C424) and point of C485 in order to good grounding on Tuner as explain below. Solder cathode of Diode Zener to the Emitter of Q2 (- point of C424), solder anode of Diode Zener to point of C485. 3. Connect a Diode zener 8.2V (VE-30001347) between the Collector of Q603 and ground for Vertical shift problem Solder cathode of Diode Zener to the Collectorr of Q603, solder anode of Diode Zener to Ground. Applied
<Parts order> VE-30001318: DIODE BA159 1A/800V 20A VE-30001347: DIODE ZENER 8.2V <Modification Start Date>
Service Bulletin
Model:
with
AK36
Priority ( )S. All product. ( )A. Items in Customer / Dealer stock / Service return goods. ( )B. Customer stock / Units returned for Service. ( )C. Sold items returned for Service. ( X )D. Only Units returned to this bulletin. ( )E. Others
SUBJECT :
Q 602 defect
<Objective>
Please modify if following symptom occurs
<Symptom>
TV does not work due to Q602 broke down
<Cause>
Hor. Transistor Driving Condition during switching ON/OFF.
<Countermeasures>
After changing the defected Q602, In order to improve Q602 resistant to sparks, modify the chassis as given below. Solder RES CF 1/4W 10K J BETWEEN BASE AND COLLECTOR OF Q601 (Hor.driver Transistor ) as shown in below.
Service Bulletin
Model:
with
AK36
Priority ( )S. All products. ( )A. Items in Customer / Dealer stock / Service return goods. ( )B. Customer stock / Units returned for Service. ( X)C. Sold items returned for Service. ( )D. Only Units returned to this bulletin. ( )E. Others
SUBJECT :
<Objective>
Please modify if following symptom occurs
<Symptom>
There is no picture on the TVs.
<Cause>
The spikes on the main supply are damaged to IC403 (Vertical output IC).
<Countermeasures>
Apply that modification: Remove D409 from the chassis, D409: DIODE 1N4148 ==> Not Connected
Service Bulletin
Model:
with
AK36
Priority ( )S. All products. ( )A. Items in Customer / Dealer stock / Service return goods. ( )B. Customer stock / Units returned for Service. ( X)C. Sold items returned for Service. ( )D. Only Units returned to this bulletin. ( )E. Others
SUBJECT :
<Objective>
Please modify if following symptom occurs
<Symptom>
After changing the CRT, Hor. Size range is not correct.
<Cause>
Some Component tolerances.
<Countermeasures>
Apply that modification: Replace;
R803: R801: RES SMD 1/10W 22K J ==> RES SMD 1/10W 22K F RES CF 1/4W 4.7K ==> RES MF 1/4W 4.7K