Professional Documents
Culture Documents
Encardio Catalog
Encardio Catalog
HIGH RISE BUILDINGS, MONUMENTS, FOUNDATIONS (D-WALL, PILES, RAFTS, ETC.) SOIL CONSOLIDATION, SEAPORTS
INDEX
PREVIEW About Encardio-rite.........................................................2 SYSTEMS Web based data monitoring service (WDMS)................ 4 Vista data vision software............................................... 4 Multilogger software ...................................................... 4 Automatic data acquisition system................................. 4 Multiplexer based system............................................... 5 BusMux based system................................................... 5 SDI-12 sensor networking system..................................5 Vibrating wire minilogger - single channel logger........... 5 PIEZOMETER / WATER LEVEL MEASUREMENT Vibrating wire piezometer............................................... 6 Vibrating wire slim piezometer........................................6 Vibrating wire low pressure piezometer..........................6 Vibrating wire push-in piezometer...................................6 Vibrating wire uplift pressure sensor...............................7 Uplift pressure with bourdon gage..................................7 Casagrande piezometer..................................................7 Standpipe........................................................................7 Dipmeter/water level sounder..........................................7 Twin tube hydraulic piezometer.......................................8 SEEPAGE / SETTLEMENT MEASUREMENT Seepage measurement system......................................8 Settlement measurement system................................... 8 Hydraulic overflow settlement gage................................9 Hydrostatic settlement profile gage................................ 9 Liquid level settlement system........................................9 PRESSURE CELLS Earth/soil pressure cell ................................................ 10 Concrete pressure cell..................................................10 Soil-concrete interface pressure cell.............................10 Jackout pressure cell.................................................... 11 Shotcrete-concrete pressure cell (NATM) ....................11 LOAD CELLS Anchor load cell - resistive strain gage type................. 12 Anchor load cell - vibrating wire type............................12 Hydraulic center hole load cell......................................12 Compression load cell...................................................13 Compression load cell - high capacity...........................13 STRAIN GAGES / SISTER BAR Spot weldable strain gage............................................ 14 Arc weldable strain gage.............................................. 14 Embedment strain gage................................................14 Electron beam welded strain gage................................14 Shotcrete strain gage....................................................15 Sister bar.......................................................................15 TEMPERATURE SENSORS Vibrating wire temperature sensor ...............................15 Thermistor temperature probe .....................................15 RTD temperature probe................................................16 Thermocouple...............................................................16 DISPLACEMENT SENSORS Vibrating wire displacement sensor.....................................17 Potentiometric displacement sensor....................................17 CRACK / JOINT METERS Mechanical crack meter ..................................................... 17 Triaxial mechanical crack meter..........................................18 Vibrating wire surface crack / joint meter.............................18 Vibrating wire embedment crack/joint meter....................... 18 Triaxial vibrating wire crack /joint meter...............................18 EXTENSOMETERS / MEASURING ANCHOR Mechanical borehole extensometer system........................19 Electronic borehole extensometer system.......................... 19 Measuring anchor............................................................... 20 Magnetic extensometer system.......................................... 20 Soil extensometer system................................................... 20 Tape extensometer............................................................. 21 TILT METER / BEAM SENSOR Portable tilt meter (voltage output)...................................... 21 Tilt meter (voltage output) - Bracket Mounting.................... 22 Tilt meter (voltage output) - Box Mounting.......................... 22 Tilt meter (voltage output) - Rail track monitoring............... 22 EL Tilt meter........................................................................ 23 EL Beam sensor..................................................................23 INCLINOMETER / IN-PLACE INCLINOMETER Inclinometer - probe, datalogger, casings........................... 24 GTILT software for inclinometer.......................................... 25 In-place inclinometer........................................................... 26 Direct & inverted plumbline................................................. 26 READ-OUT UNITS / DATALOGGERS Vibrating wire read-out unit................................................. 27 Resistive strain gage read-out unit......................................27 Tilt meter read-out unit........................................................ 27 Potentiometric read-out unit................................................ 27 4-20 mA output read-out unit...............................................27 GEODETIC TARGETS & SURVEY MARKERS Reflective targets (bireflex and prism)................................ 28 Building settlement point..................................................... 28 Pavement settlement point..................................................28 Ground settlement point......................................................28 ACCESSORIES Cables................................................................................. 29 Junction boxes.................................................................... 30 Switch cum terminal boxes................................................. 30 Cable jointing kit..................................................................30 Cable splicing kit................................................................. 30 AUTOMATIC WEATHER STATION....................................30 AGENCIES Gralp Systems Ltd., UK.....................................................31 Geotech Instruments (UK) Ltd.............................................31 Amberg Technologies AG.................................................... 31
A
The Company
Encardio-rite Electronics Pvt. Ltd. was incorporated on June 14, 1966 in India. It is a world leader and operates extensively globally as well as in India. In India it has branch offices at Delhi, Mumbai, Chennai, Bangalore, Hyderabad, Kolkata and Reyasi (J&K). Encardio-rite exports to all major countries in the Americas, Europe, East Asia, Middle East, Africa and Australia through its marketing associates and dealers. Encardio-rite and its associate companies have an employment of around 250 personnel. In the Middle East, Encardio-rite operates through Encardio-rite Geosystems LLC, UAE and Encardio-rite Geosystems WLL, Bahrain.
Wide experience
Encardio-rite has facilities & technical capability to meet challenging demand of sophisticated instrumentation in the field of civil engineering: l Metros, Tunnels; large number of metros including Delhi and Dubai on a turnkey basis, several other
l
metros worldwide through its marketing associates Hydroelectric Projects; more than 300 concrete, RCC, concrete faced rock filled and earth/rock filled dams, underground cavities; tunnels; wye sections; pressure shafts; surge tanks etc. High rise buildings, Monuments, (diaphragm walls, pile, strut, etc) Airports; Seaports; Highways, Bridges.
Foundations
Complete
Product
range
and
Services
nder elding u beam w 01 Torr n Electro um of 0.0 ulting in a vacu sor, res side sen protection in IP-68
measurement of pressure, displacement, settlement, inclination, tilt, stress, load etc. Our instruments measure parameters that govern elements of design, construction monitoring and the safety of structures. Our services include: l Installation and Monitoring through our experienced
l
technical personnel Monitoring through our Web base Server (online through internet) Pre-construction and Post-construction building/
structure condition survey Surveying with total stations & digital level.
PREVIEW
from time of supply & installation to long term usage. With our sustained effort, this has gradually developed and resulted in the concept: Once our customer, always our customer.
www.encardio.com
Technology
Encardio-rite excels in both vibrating wire and resistive strain gage technology for sensors. The company ranks among the few organisations in the world manufacturing international quality vibrating wire instruments. Vibrating wire sensors manufactured by Encardio-rite are one of the finest being produced anywhere in the world. A large number of our sensors are of stainless steel construction, hermetically sealed by electron beam welding under a vacuum of 0.001 Torr inside them, resulting in IP-68 protection. This results in sensor being almost completely resistant to effect of corrosion and ingress of moisture and water.
R & D Division
The R & D Division is committed to excellence. This has motivated the organization to tackle challenging technological advancements with single minded devotion and with the objective of achieving excellence in instrumentation. New products with better manufacturing techniques are constantly being developed with updated technologies to take care of changing requirement of the construction industry.
m Environ ental ch amber
Quality assurance
Encardio-rite is an ISO 9001:2008 certified organization. It has an independent division for quality assurance and has built-up its reputation based on the quality and long term reliability of its products. Encardio-rite has in-house facilities for testing almost all the specifications listed in the products catalogue. Typical tests conducted on the products for assuring long term reliability are Ambient temperature test, Humidity test, Long term drift, Mechanical shock, Mechanical vibration test, Accelerated cyclic life test.
* SYSTEMS
Web based (WDMS) Data Monitoring Service Multilogger software
Multilogger software is a Windows based software for downloading and analysing data from CR-1000 based EDAS-10 data acquisition system. Each measurement channel can be configured for instrument type and programmed to output temperature corrected data in engineering units. Alarm limits can also be specified. The Multilogger uses the entered information to generate an appropriate datalogger program automatically. Multilogger includes a powerful data analysis tool comprised of a data editor, data selector, Excel compatible spreadsheet, report generator and carting tool.
The web based data monitoring service (WDMS) is a webbased data-management and presentation tool for data collected by model EDAS-10 data acquisition system from a project site. The system handles all data processing requirement, starting with collection and storage of data, performing the required calculations on the data, presenting the results in graphical and numerical format and generating alarm messages. The monitoring software is server based. Users interact with the software using their web-browser, when connected to the Internet, from any location in the world. It also allows multiple authorized users at different locations to view any data or report from the same project site simultaneously. The graphs & reports can be viewed using popular web browsers like Microsoft internet explorer or Mozilla Fire fox amongst others. The server for the above WDMS services is located at the Encardio-rite premises and is maintained 24 x 7.
automatic
data
EDAS-10 delivers accurate and reliable measurement in a variety of applications. It is most suitable for unattended or network applications. Various options are available for connecting the data acquisition system to PC, like RS232C serial interface, short haul modems, RF modem etc. Built around the Campbell Scientific's middle level programmable measurement and control module, the Encardio-rite data acquisition system is available in multiple configurations depending upon the type, number
browsing, reporting and publishing to the web with the support of 3 modules i.e. db.robot.c for storing editing the data, db.data.browser that allows user to display data from multiple stations and db.web.browser that allows to publish and give web access to all data and advanced reports. Requirement: Operating System Windows 2000, Professional, Windows XP, Home or XP Professional 128 MB (minimum), 512 MB, or Memory requirement more (recommended) Hard disk requirement 90MB (minimum for installation)
of sensors used and their locations in a particular project. Few such system configurations are mentioned below along with brief description to give an idea on the type of systems/solutions available. Please contact us for any specific requirement giving details of the type, quantity and locations of sensors used in the particular project.
Specifications
Resolution Scan rate Power consumption Power requirement Storage capacity Temperature limit 0.66 micro Volt (analog) Few times/sec to once/hour 50 mA during measurement 9.6 to 16 V DC 2 MB data point, (expandable with peripherals) -25 to 500C
Surge protection is built into the BuxMux input and output lines; so an additional surge protection card is not required.
Datalogger with SDI-12 interface - CR-1000 or CR-200 Vibrating wire SDI-12 interface (with surge protection) model EVM-108 8 channel (8 x 4 wire, 16 x 2 wire) or model EVM-101 single-channel used with EAM-416 multiplexer to connect 16 x 4 wire or 32 x 2 wire sensors.
Sensors with SDI-12 interface - all sensors other than vw type like resistive strain gage type load voltage output, in-place sensors etc. cells, tilt meters with
Specifications
Frequency range Parameters Temperature measurement range 450 Hz to 6000 Hz Time, Frequency, engineering units -20 to 50 C
0
* PIEZOMETER
Model EPP-30V vibrating wire piezometer
EPP-30V is a vibrating wire piezometer used to measure pore water pressure in soil, earth/rockfills, foundations and concrete structures. EPP-30V is of stainless steel construction and hermetically sealed under a vacuum of 0.001 Torr. Each sensor has built-in thermistor for temperature measurement and surge arrestor for lightning protection. A glass to metal seal solder pin connector is provided for easy cable connection. The piezometers are very suitable for use as multi-level piezometers mounted at different levels in the borehole using the groutin technique.
Specifications
Range (MPa) Accuracy Non linearity Over range limit Temperature limit Thermistor Dimension (f x L) 0.2, 0.35, 0.5, 0.7, 1.0, 1.5, 2.0, 3.5, 5.0, 10.0, specify 0.25 % fs normal 0.1 % fs optional 0.5 % fs 150 % of range -20 to 80 C YSI 44005 or equivalent 42 x 185 mm
0
Specifications
Range (MPa) Accuracy Dimension (f x L) 0.35, 0.5, 0.7, 1.0, 2.0 0.2 % fs normal 0.1 % fs optional 19 x 155 mm
Specifications
Specifications
Range (MPa) Accuracy Non linearity Over range limit Temperature limit Thermistor Dimension (f x L) 0.35, 0.5, 0.7, 1.0, 2.0 0.2 % fs normal 0.1 % fs optional 0.5 % fs 150 % of range -20 to 80 C YSI 44005 or equivalent 35 x 166 mm
0
Specifications
Range (MPa) Accuracy Non linearity Over range limit Temperature limit Thermistor Dimension (f x L) 0.2, 0.35, 0.5, 1.0, specify 0.25 % fs normal 0.1 % fs optional 0.5 % fs 150 % of range -20 to 80 C YSI 44005 or equivalent 42 x 210 mm
0
Specifications
EPP-10 Casagrande tip Standpipe EPP-10SP Porous tip Standpipe 50 mm o.d. slotted pipe 50 mm o.d., 3 m long each 37 mm o.d., 25 mm i.d., 20, 40, 60 cm long 25 mm o.d., 3 m long each
Specifications
Length (m) Resolution Length (ft) Resolution 30, 50, 100, 150, 200, 300 1 mm standard 50, 100, 150, 300, 500 0.1 standard
Sensor Specifications
Range (MPa) Accuracy Over range limit Temperature limit Thermistor 0.2, 0.35, 0.5, specify 0.25 % fs normal 0.1 % fs optional 150 % of range -20 to 80 C YSI 44005 or equivalent
0
Specifications
Range (m) System accuracy Temperature limit Reservoir housing NOTE: Sensor accuracy Sensor non-linearity Thermistor 0.1 % fs 0.50 % fs YSI 44005 or equivalent 7, 20, 30, 50, 70 0.25 % fs to 1 % fs -20 to 80 C (sensor) 400 h x 300 w x 220 d mm
0
* SETTLEMENT
Model EHOS-35 hydraulic overflow settlement gage
The EHOS-35 settlement gage is suitable for monitoring settlement or heave in embankments, embankment foundations and earth dams. It consists of a graduated standpipe and a sealed settlement cell with three accesses - first for an overflow pipe which is connected by a nylon tubing to the standpipe, second allows drainage of excess water from the cell and the third access allows atmospheric pressure to be maintained inside the cell. The cell is installed in soil fill and the standpipe on firm ground outside the structure. De-aired water is filled in the standpipe and tubing connecting it to the cell. Comparing the water level in the standpipe with earlier readings taken gives the settlement/ heave to which the cell is subjected.
Specifications
Measured range (m) 1, 1.5, 2, 3, specify Resolution 1 mm
Specifications
Probe Measuring range Sensor accuracy Resolution Temperature limit Thermistor
1 1
2 mm
-20 to 80 C
0
Specifications
Range (mm) Resolution (mm) Accuracy Non-linearity Temperature limit Thermistor 150, 300, 600 specify 0.07, 0.15 0.1 % fs 0.5 % fs -20 to 800C YSI 44005 or equivalent
* PRESSURE CELL
Model EPS-30V-S earth/soil pressure cell
EPS-30V-S earth pressure cell is designed to measure total pressure in earth fills and embankments. The flexible, circular flat pressure pad is constructed from two stainless steel discs electron beam welded around the periphery. The pressure pad is connected to the vibrating wire pressure sensor through a 6 mm dia x 165 mm long stainless steel tube. The narrow cavity inside the pressure pad and tube is fluid filled. Pressure applied by earth on the capsule is transmitted through the fluid to the vibrating wire pressure sensor, which converts it into an electrical signal.
Specifications
Range (MPa) Accuracy1 Over range limit Temperature limit Thermistor Pressure pad size
1
0.5, 1.0, 2.0, 3.5, 5.0, 10.0, specify 0.5 % fs normal 0.1 % fs optional 150 % of range -20 to 800C YSI 44005 or equivalent 200 mm f x 7 mm thick
Specifications
Same as EPS-30V-S
Specifications
Pressure pad size 200 mm f x 10 mm thick Other specifications same as EPS-30V-S
10
* PRESSURE CELL
Model EPS-30V-J jackout pressure cell
EPS-30V-J jackout pressure cell is designed to measure stress on base slabs, diaphragm/slurry walls, etc. It consists of a thin flexible stainless steel round flat diaphragm electron beam welded to a thick, rigid back plate around the periphery leaving a narrow space between the two. A vibrating wire pressure sensor is electron beam welded concentric with the back plate. The cavity inside the sensor is filled with deaired fluid.
Sensor Specifications
Range (MPa) Accuracy1 Over range limit Temperature limit Thermistor Overall size (mm)
1
0.5, 1.0, 2.0, 3.5, 5.0, specify 0.5 % fs normal 0.1 % fs optional 150 % of range -20 to 80 C YSI 44005 or equivalent 125 f x 190 h 200 f x 190 h standard
0
Sensor Specifications
Range (MPa) Accuracy
1
1.0, 2.0, 3.5, 5.0, 10.0, 20.0, 30.0, specify 0.5 % fs normal 0.1 % fs optional 150 % of range -20 to 80 C YSI 44005 or equivalent 100 x 200 150 x 250 200 x 300 300 x 300
0
Over range limit Temperature limit Thermistor Pressure pad sizes l x b (mm)
11
* LOAD CELL
Model ELC-30S resistive strain gage type centre hole/anchor bolt load cell
ELC-30S is a resistive strain gage type center hole load cell used to determine load in rock bolts, tieback anchors, etc. It comprises of a cylinder of high strength steel with eight 350 Ohm resistance strain gages, wired to form a 700 Ohm bridge. To minimize the effect of uneven and eccentric loading, the eight gages are mounted around the circumference at 45 to each other. The load cell is hermetically sealed by electron beam welding making it immune to ingress of water and to most corrosive environments.
Specifications
Range (kN)/ID (mm) 200/40, 500/52, 1000/78, 1000/105, 1500/85, 1500/130, 2000/105, 2000/155, specify Over range capacity Calibration accuracy Non-linearity Output Excitation Temperature limit Cable connection 150 % 0.25 % fs 1 % fs 2 mV/V 10 % 10 V DC (max. 20 V DC) -20 to 80 C Six pin glass to metal seal
0
Model ELC-30S-H resistive strain gage type centre hole/anchor bolt load cell
ELC-30S-H high capacity center hole load cell is similar to model ELC-30S load cell. This high capacity load cell comprises of a high strength stainless steel element with sixteen 350 Ohm resistance strain gages, wired to form a 1400 Ohm bridge. The 3500/185 and 5000/202 load cells are electron beam welded.
Specifications
Range (kN)/ID (mm) 3500/185, 5000/202, 7500/226, 10000/210, specify Over range capacity Non-linearity Output Excitation Temperature limit Cable connection 120 % 1 % fs ( 0.5 % fs is available) 1.5 mV/V 20 % 10 V DC (max. 20 VDC) -20 to 80 C
Four core shielded 5m long, specify
0
Specifications
Range (kN)/ID (mm) 250/35, 500/52, 750/78, 1000/105, 1500/105, 2000/130, 2500/0 Overload Calibration accuracy Non-linearity Temperature limit Temperature effect on zero 110 % fs 0.25 % fs 2 % fs from 10% to full range -10 to 55 C 0.05% fs/ C YSI 44005 or equivalent
0 0
Thermistor
Specifications
Range (kN)/ID (mm) 250/35, 500/52, 750/78, 1000/105, 1500/105, 2000/130 Over range capacity Resolution Temperature limit 110 % fs 100 division fs -10 to 55 C
0
12
* LOAD CELL
Model ELC-32V vibrating wire center hole/ anchor bolt load cell
ELC-32V is vibrating wire type center hole load cell used to determine load in rock bolts, tieback anchors, etc. It comprises of a cylinder of high strength martensitic stainless steel with three vibrating wire strain gages mounted at 120 to each other to minimize the effect of uneven and eccentric loading. To determine the load, the average of the three readings is taken. Load cell with six vibrating wire strain gages and nine core cable is available on request. Solid load cell for stress measurement in tunnel supports and struts is also available on request.
Specifications
Range (kN)/ID (mm) 250/27, 500/52, 1000/78, 1500/102, 2000/127, 2000/152, specify (solid load cell also available on request) Overload Calibration accuracy Non-linearity Temperature limit Thermistor Cable 150 %
0.25 % fs 1 % fs
Specifications
Range (kN) Rated output Enclosure 1000, 1500, 2000, 3000, 3500 1.5 mV/V 10 % IP 68, electron beam welded under a vacuum of 1/1000 Torr
Temperature limit -20 to 800C
Cable
Specifications
Range (kN) 5000, 6000, 7500, 10000 & 12500 Over range capacity 120 % with a maximum upto 14000 kN Rated output
Temperature limit
1.5 mV/V 10 %
-20 to 800C
Cable
13
* STRAIN GAGE
Model EDS-20V-SW vibrating wire spot weldable strain gage
EDS-20V-SW vibrating wire strain gage can be spot welded or epoxy bonded on steel structures and struts. It can also be epoxy bonded on concrete structures. A sensor coil housing mounted directly over the strain gage, completely encloses the sensor, forming a watertight enclosure. A pair of clamps are provided to aid in fixing the housing to the substrate using an epoxy adhesive.
Specifications
Range Sensitivity Active gage length Thermistor Temperature limit Cable 3000 strain 1 strain 50.8 mm YSI 44005 or equivalent -20 to 80 C Four-core shielded 1 m long; specify
0
Size l x b x h (mm) 87 x 22 x 18
Specifications
Range Sensitivity Active gage length Thermistor Temperature limit Cable 3000 strain 1 strain 150 mm YSI 44005 or equivalent -20 to 80 C Four-core shielded 1 m long; specify
0
Specifications
Size l x b x h (mm) 170 x 28.5 x 30 Other specifications same as EDS-20V-AW.
Specifications
Range Sensitivity Active gage length Thermistor Temperature limit Protection Cable connection 1500 strain 1 strain 140 mm YSI 44005 or equivalent -10 to 80 C IP 68 Glass to metal seal solder pin connector
0
14
Specifications
Range Effective gage length Overall diameter Protection class Temperature limit Cable 15,000 strain 166 mm 19 mm IP 68 -20 to 70 C Four-core shielded 1 m long; specify
0
Specifications
Range Sensitivity 2500 strain 1 strain 30 x 1400 (for 16 mm f nominal) Temperature limit Thermistor Cable -20 to 80 C YSI 44005 or equivalent Four-core shielded 1 m long; specify
0
Specifications
Range Accuracy Enclosure -20 to 80 C 0.5 % fs normal 0.1 % fs optional Stainless steel, IP 68 hermetically sealed by electron beam welding
0
Specifications
Sensor type R-T curve matched NTC thermistor, equivalent to YSI 44005 Range Accuracy Body material -20 to 80 C 1C Tin plated copper
0 0
15
* TEMPERATURE * THERMOCOUPLE
Model ETT-10PT RTD temperature probe
ETT-10PT can be used in similar applications as ETT-10TH. The probe has excellent stability and accuracy that makes it well suited for long-term installations where high accuracy and reliability is required. It consists of a ceramic resistance element (Pt 100) with DIN IEC 751 (formerly DIN 43760) European curve calibration. The resistance element is housed in a closedend robust stainless steel tubing that protects the element against moisture.
Specifications
Sensor type Range Accuracy Calibration Curve (European) Pt 100 -20 to 80 C (0.3 + 0.005*t) C value of temperature in C DIN IEC 751 0.00385 Ohms/ Ohm/ C
0 0 0 0
Thermocouple
Thermocouple measurement consists of a thermocouple wire with two dissimilar conductors (Copper-Constantan) joined at one end to form a hot junction. This end is sealed against corrosion and placed at the required locations of temperature measurement. The other end of the thermocouple wire is connected to a suitable thermocouple connector to form a cold junction. At the cold junction compensation (or reference end), the mV value provided by the thermocouple represents the difference in temperature of the sensing end as compared to the reference end. The thermocouple readout displays a direct reading of the temperature at the installed location and automatically compensates for the temperature at the cold junction.
Specifications
Thermocouple Wire Type Insulation Hot junction (Maximum) temperature Cold Junction Temperature Thermocouple Connector Type Service temperature Thermocouple handheld readout Sensor Type Input Display Range Accuracy Alarms T type thermocouple (Copper-Constantan) Two Two 4 digit + one 6 digit -2000C to 4000C 0.05 % High/Low (audible) Miniature type glass filled Nylon -200C to 1000C Up to 2600C Ambient T-Copper-Constantan PFA Teflon
16
Specifications
Transducer type Range (mm) Accuracy Sensitivity Non-linearity Temperature limit Thermistor Cable Vibrating wire 25, 50, 100 or 150 0.2 % fs normal 0.1 % fs optional 0.02 % fs 0.5 % fs -10 to 80 C YSI 44005 or equivalent Four-core shielded 1 m long; specify
0
Specifications
Transducer type Range (mm) Input Output Accuracy Sensitivity Temperature limit Cable Potentiometric 50, 100, 150 5 ~ 13 V DC 0 - 2 V DC (nominal) 0.1 % fs 0.02 mm -10 to 80 C Four-core shielded 1 m long; specify
0
Specifications
Range (mm) Resolution 50, 100 0.5 mm
17
* CRACK/JOINT METER
Model EDJ-40TJ triaxial crack/joint meter
EDJ-40TJ used for surface measurement consists of two-precision machined elements attached to re-inforced bar anchor stems. Measurement is made by anchoring the two element on either side of joint/crack and accurately measuring the distance between them over a period of time with a depth gage of 50 mm range and 0.01 mm resolution.
Specifications
Range (mm) Resolution Material 15 in X, Y, Z direction 0.01 mm Aluminium with stainless steel bushes and pins; epoxy painted Optional AISI 304 stainless steel construction
Specifications
Range (mm) 15, 25 specify Refer to EDE-VXX vibrating wire displacement sensor, for sensor specifications
Specifications
Range (mm) Accuracy Sensitivity Non-linearity Temperature limit Thermistor 15, 25, 50, specify
0.2 % fs normal 0.1 % fs optional 0.02 % fs 1.0 % fs
Specifications
Refer to EDE-VXX vibrating wire displacement sensor, for sensor specifications
18
* BOREHOLE EXTENSOMETER
Model EDS-63U/D mechanical borehole extensometer system
EDS-63U/D borehole extensometer mechanically measures deformation of rock mass and adjacent surrounding soil. It is available in 2-3 points suitable for a 76 mm borehole and 4-6 points suitable for a 102 mm borehole. The system comprises of anchors (groutable or packer), extension rods (stainless steel or fiber glass) in protective covering and a h e a d a s s e m b l y. A d i g i t a l caliper/micrometer depth gage with a resolution of 0.01 mm is used to take readings.
Specifications
Refer to EDE-VXX vibrating wire displacement sensor or EDE-PXX potentiometric displacement sensor for sensor specifications.
Specifications
Refer to EDE-VXX for vw displacement sensor and EDE-PXX for potentiometric displacement sensor
19
* EXTENSOMETER
Model EMA-11 measuring anchor
EMA-11 measuring anchor, also known as rock bolt extensometer, is a combination of rock bolt and extensometer. It is used to determine load exerted on rock bolts. It is a precision instrument designed to evaluate anchor system forces and their distribution within the bolt and hence its safety and effectiveness. A digital caliper/micrometer depth gage with a resolution of 0.01 mm is used to take readings. An electrical head assembly consisting of four potentiometric sensors is optionally available for electrical output.
Specifications
Length Fixed points Borehole diameter Anchor diameter Loading capacity Range Resolution Linearity Enclosure 3, 4, 6 m 4 51 mm 26.7 mm nominal 250 kN 5 mm 0.01 mm 0.2 % fs IP 65
Electrical measurement
Specifications
Range (m) Resolution Probe dimension Access tube 30, 50, 100, 150, 200, 300 1 mm 22 mm f, 150 mm long PVC, 25.5 mm i.d., 32.5 mm o.d., 3 m long, fitted at both ends, with telescopic couplings having dimensions 35 mm i.d., 31.5 mm o.d., length 1m, 2m, 3m Range (ft) Resolution 50, 100, 150, 300, 500 0.1 standard
Specifications
Refer to EDE-VXX vibrating wire displacement sensor for sensor specifications
* EXTENSOMETER * TILT
Model EDS-80 tape extensometer
EDS-80 tape extensometer is designed to measure small changes in distance between two reference points in any orientation, to give deformation of underground openings, excavations, tunnels, roof of a mine, movement of unstable slopes, etc. The readings are displayed on a 5 digit LCD display.
Specifications
Tape length 30 m or 50 m Precision in 0.2 mm measurement of change LCD resolution 0.01 mm Coefficient of linear 11 ppm/0C expansion (6.1 ppm/0F)
Specifications
Sensor Measuring range Sensitivity Accuracy Temperature limit Size l x b x h (mm) Dimension (tiltplate) Uniaxial 150 10 arc seconds 0.1 % fs -20 to 800C 162 x 90 x 145 142 mm f x 24 mm th
21
* TILT METER
Model EAN-90M tilt meter
EAN-90M tilt meter is suitable for monitoring inclination and vertical rotation in structures such as building, dams etc. It is a rugged, high resolution tilt meter. The tilt meter is fixed on a vertical or horizontal surface by means of an adjustable bracket and expandable anchor. The tilt meter can be supplied as a biaxial version in the same enclosure. It has a voltage output which can be read by any indicator that measures differential voltage output and can also be directly connected to Encardio-rite data acquisition system. The sensor is electron beam welded with a vacuum of 1/1000 Torr inside it. Model EAM-92m option is available with SDI-12 interface such that all sensors can be connected through single bus cable to the datalogger.
Uniaxial or biaxial 15
0
Specifications
Sensor Measuring range Output (nominal) Sensitivity Accuracy
1
Specifications
Sensor Measuring range Output Sensitivity Accuracy Beam Beam length
1
Temperature limit
22
Specifications
Sensor Measuring range** Linear range Resolution Repeatibility Temperature limit Dimension (mm) Electrolytic level type, Uniaxial 1 (60 arc minutes) 0.5 (30 arc minutes) 1 arc second 3 arc seconds -20 to 50 C 125 x 80 x 57
0 0 0
** Note: Polynomial-linearisation co-efficients are provided for utilising full measurement range of 10 .
Specifications
Sensor Measuring range ** Linear range Resolution Repeatibility Temperature limit Beam Electrolytic level type, Uniaxial 1 (60 arc minutes) 0.5 (30 arc minutes) 1 arc second 3 arc seconds -20 to 50 C 38 x 38 mm, aluminium with 1 m, 2 m and 3 m options
** Note: Polynomial-linearisation co-efficients are provided for utilising full measurement range of 10 .
0 0 0
Specifications
Sensor Measuring range ** Linear range Resolution Repeatibility Temperature limit Beam Electrolytic level type, Uniaxial 1 (60 arc minutes) 0.5 (30 arc minutes) 1 arc second 3 arc seconds -20 to 50 C 38 x 38 mm, aluminium with 1 m, 2 m and 3 m options
** Note: Polynomial-linearisation co-efficients are provided for utilising full measurement range of 10 .
0 0 0
23
* INCLINOMETER
Model EAN-25M inclinometer system
EAN-25M vertical inclinometer system is used to measure lateral movement and deformation of earth works or a structure. It provides magnitude of inclination or tilt and its variation with time in structures like retaining/ diaphragm walls, piles etc. EAN-25/M-H horizontal inclinometer system, provides significant quantitative data on magnitude of settlement/heave of foundations and its variation with time. It also provides the pattern of deformation, zones of potential danger and the effectiveness of construction control measures undertaken. The inclinometer system basically consists of inclinometer casings with couplings, probe with operating cable and datalogger. Accessories like dummy probe, calibration check jig, cable lowering bracket are available on demand.
Specifications
System accuracy 6 mm/30 m
Vertical probe
Measuring range Resolution Temperature limit Dimensions
0
Horizontal probe
Measuring range 150 to horizontal Other specifications are same as EAN-25/2M vertical inclinometer probe
24
* INCLINOMETER
Model EDI-53INS inclinometer datalogger
The data logger is housed in a rugged weather proof enclosure. It can store readings with date and time. It is battery operated with an easy to read display. It is supplied complete with software to transfer the data to a PC for further processing or for archive purposes.
Datalogger
Display Resolution Range Operating temp. range LCD 0.0001 V @ 2 V fs range 2 V, 4 V, 8 V (factory configured) 0 to 500C
InclinoView
ER InclinoView software has been designed to process borehole data from Encardio-rite's EAN-26M digital inclinometer. It is suitable for plotting mean deviations, absolute borehole profile, cumulative deviation against depth and time vs deviation and vector plots at each depth. It can also plot checksums for assessment of quality of data. Plots can be easily switched between top or bottom reference. The plots can be viewed along inclinometer casing grooves or along a skew angle. Spiral correction can also be applied if such data is available. InclinoView allows inclinometer data for the same borehole to be automatically correlated for excavation or fills and benchmark elevation or fill levels with date can be annotated on the plots. Sub soil stratigraphy layers can also be marked on the plots together with user comments. InclinoView allows data from a large number of boreholes from different sites to be organized and stored on the users' PC. InclinoView can run on both Microsoft Windows (XP and later operating systems) and Linux platforms.
25
Specifications
Sensor Measuring range** Accuracy Temperature limit Uniaxial or biaxial 15 0.1% fs -20 to 80 C
0
Specifications
Measuring range Resolution Accuracy Table size 75 mm (direct) 50 mm (inverted) 0.01 mm 0.1 mm 625 mm x 625 mm
26
* READ-OUT UNIT
Model EDI-51V portable vibrating wire read-out unit/datalogger
EDI-51V is used to read any Encardiorite vibrating wire sensor. It can display the measured frequency in terms of time period, frequency, frequency squared or the value of measured parameter directly in proper engineering units. It has memory to store around 4500 readings with date and time from up to 500 sensors. The read-out unit comes with rechargeable batteries and a suitable battery charger, RS232C serial interface, necessary cables and manual.
Specifications
Frequency range Parameters Resolution Temperature measurement range Temperature limit Housing 0 to 50 C ABS + PU impact resistant plastic moulded housing
0
500 Hz to 5 kHz Time period, frequency, freuqency , engineering units 0.01 micro-seconds 0 - 50 C
0 2
Specifications
General Operating temp. limit 0 to 50 C
0
Model EDI-53L
EDI-53L is used for resistive strain gage sensors including load cells.
Model EDI-53L Input Resistance strain guage bridge load cell with 0 ... 3 mV/V output Excitation voltage Preamplifier gain Model EDI-53ELV Input Excitation voltage EL tiltmeter (Voltage output) 12 V DC (nomial) 5 V DC 100
Model EDI-53ELV
EDI-53ELV is used to read tilt meter and stores data in volts. Note: Value in engineering units can be calculated in Microsoft Excel sheet using polynomials co-efficient given in test certificate of tilt meter.
Model EDI-53P
Model EDI-53P is used to read potentiometric displacement transducers with 0-2 V full scale voltage output. Model EDI-53P Input Excitation voltage 0-2 V DC 5 V DC
Model EDI-53I
EDI-53I is designed to read transducers with 4-20 mA DC current output. Model EDI-53I Input Input resistance Model EDI-53UTM Input Excitation voltage 2 V, 4 V, or 8 V (factory configured) 12 V DC 4-20 mA DC current 50 Ohm
Model EDI-53UTM
Model EDI-53UTM is designed for use with Encardio-rite's range of uniaxial tilt meters. However, with an external switch it can also be used with biaxial tilt sensors.
27
Specifications
ERT-10B bi-reflex target 1 Typically 12 m to 140 m Measuring range Material
ERT 10-B
Reflector support is plastic, mounted on universal joints with reflective foil on both sides.
Maximum measuring distance is highly dependent on atmospheric conditions and EDM model used.
w
Model ERT-20P2-M1 mini prism target
ERT-20P2-M1 mini prism consists of a prism mounted on a swivel bracket. This target is not interchangeable. The prism is copper coated.
Convergence bolt of galvanized steel constructions, 12 mm diameter x 170 mm long, with 3x8" pipe thread stud with protective cap.
28
* CABLE
1. CABLE
Model Series CS-0401 series CS-0402 series Specifications Model Use CS-0601 series No. of cores Color code OD.
Weight (approx.)
7/0.25 mm ATC, twisted pairs screened with water blocking aluminum foil, 0.3 mm galvanized iron wire braid armoured, overall polythene sheathed, variants as follows: CS-0402-1P 2-core red/black 10 mm 0.1 kg/m CS-0402-2P 4-core red/black & green/white 11 mm 0.12 kg/m CS-0402-3P 6-core red/black, green/white & blue/grey 11.5 mm 0.14 kg/m CS-0402-4P 8-core all different 12.5 mm 0.16 kg/m CS-0402-6P 12-core all different 14 mm 0.40 kg/m CS-0402-10P 20-core all different 16 mm 0.3 kg/m CS-0402-20P 40-core all different 19.8 mm 0.60 kg/m 7/0.20 mm silver plated copper with braid, 4 core screened cable in red, black, green, white, screened with aluminized polyester film, with drain wire, PTFE sheathed, 3.5 mm o.d., unit weight (approx.) 0.03 kg/m 7/0.20 mm ATC, 4-core cable with red/black & white/black, foil shielded; chrome PVC jacket. Maximum service temperature 80 C, ~ 5.6 mm o.d, unit weight (approx.) 0.35kg/10 m. 7/0.20 mm ATC; foil shielded; chrome PVC jacket, variants as follows: CS-0405-6 6-core black/white, red/green & brown/blue 5.8 mm CS-0405-9 9-core black, white, red, green, brown, 6.2 mm blue, orange, yellow & violet 0.04 kg/m 0.05 kg/m
7/0.25 mm ATC, dual twisted pair signal cable, foil shielded; chrome PVC jacket. Maximum service temperature 60 C, ~ 4.3 mm o.d., unit weight (approx.) 0.30 kg/10 m. 7/0.2 mm annealed copper, petroleum jelly filled, 0.9 mm f galvanized sheet armoured, overall PE black sheathed, variants as follows: CS-0407-5P 10-core all different 18 mm 0.45 kg/m CS-0407-10P 20-core all different 19 mm 0.50 kg/m CS-0407-20P 40-core all different 20 mm 0.55 kg/m 7/0.255 mm annealed tinned copper, 4 core dual twisted cable in red/black & green/white, screened with aluminized polyester film, polyethylene insulation, with drain wire, polyurethane sheathed, 6.3 mm o.d., unit weight (approx.) 0.06 kg/m 7/0.2 mm ATC, datalene insulated, low capacitance, shielded cable, chrome PVC jacket, variants as follows: CS-0410-5 5-core red, black, white, green & brown 6.25 mm 0.05 kg/m CS-0410-8 8-core red, black, white, green, brown, 7.1 mm 0.08 kg/m orange, blue & yellow 7/0.2 mm annealed copper, dual twisted pair screened cable in red/black & green/white, with vent tube, polyurethane sheathed, yellow colour, ~ 9 mm o.d., unit weight (approx.) 0.08 kg/m 7/0.25 mm annealed copper, dual twisted pair screened cable in red/black & green white, PVC sheathed, red colour, ~ 6.0 mm o.d., unit weight (approx.) 0.55 kg/ 10 m 7/0.25 mm annealed copper, petroleum jelly filled, 0.9 mm f galvanized sheathed; variants as follows: CS-0601-2 2 core red/black CS-0601-4 4 core red/black & green/white CS-0601-6 6 core red/black, green/white & blue/grey steel wire armoured, polythene 15 mm 15.5 mm 16.5 mm 0.3 kg/m 0.35 kg/m 0.40 kg/m
CS-0408
CS-0410 series
19 x 0.20 mm annealed tinned copper, 6 core twisted cable in red/black, green/white & blue/grey, screened with aluminized polyester film, polyethylene insulation, with drain wire, polyurethane sheathed, 10.4 mm o.d. 7/0.25 mm annealed copper, dual twisted pair screened cable in red/black & green/white, screened with aluminized polyester film, polyethylene insulation, with drain wire, polyurethane sheathed, 6.35 mm o.d. 7/0.25 mm ATC, 6 core cable in black, white, red, green, brown, blue, screened with aluminized polyester film, polyethylene insulation, with drain wire, polyurethane sheathed, 6.5 mm o.d. 7/0.25 mm annealed copper, 3 core screened cable in red, black & green, screened with aluminized polyester film, polyethylene insulation, with drain wire, polyurethane sheathed, 4.7 mm o.d.
29
Suitable for connecting input from up to 10 sensors through ten 4-core input cables to one output cable. Suitable for connecting input from up to 10 sensors through 6-core input cables to one output cable. Suitable for connecting input through N (specify number) X-core (specify core) input cables to one output cable. YZ = specify cable code or cable f (for input & output cable)
3. SWITCH BOX
ESB-10-4-YZ ESB-12-4-YZ ESB-N-12-YZ ESB-N-X-YZ
Suitable for connecting and switching input from up to 10 sensors through ten 4-core input cables to readout unit and to one output cable. Suitable for connecting and switching input from up to 12 sensors through twelve 4-core input cables to readout unit and to one output cable. Suitable for connecting and switching input from up to 12 sensors through N 12-core input cables to readout unit and to one output cable. Suitable for connecting and switching input through N (specify number) X-core (specify core) input cables to the read out unit and to one output cable. YZ = specify cable code or cable f (for input & output cable)
30
* AGENCIES
Gralp Systems Ltd., UK
(for micro-seismometers, strong motion accelerometers and associated products)
Encardio rite is sole agent in India of Gralp Systems Ltd., UK for its complete range of equipment for seismology, science and engineering. Gralp Systems Ltd is a world leader in the design and manufacture of low-noise broadband seismometers, strong motion accelerometers, analog and digital seismic instruments, digitizers and networking equipment. These are used for monitoring and furthering understanding in a range of applications such as Earthquake early warnings, Tsunami early warnings, Volcano monitoring, Ocean bottom seismology, Seismic surveying, Civil Engineering/Structural integrity, Petrochemical exploration, Security systems and Blast monitoring. For further details on the range of products visit http://www.guralp.co.uk.
Product range:
l l l
Landfill: Landfill portable gas analysers with built in GPS systems. Leachate pumps and dipmeters also available. Biogas: Fixed and portable analyser equipment enables continuous monitoring of biogas in a range of applications. Water: Highly dependable range of top quality pneumatic submersible pumps for level control and also equipments for sampling and water quality checks. Fixed gas monitoring: In-house design capability has resulted in continuous development of static gas monitoring systems. CO2 & N2O monitoring: Analysers used in laboratories for carbon dioxide incubators, to verify IVF, food production, air quality and life-critical applications. Remediation: Equipments available to tackle contamination such as fuel spills, fuel tank or chemical plant leaks. For further details visit http://www.geotech.co.uk
l l
Amberg Technologies AG
l
Amberg Technologies is a Swiss company belonging to the Amberg Group. It is a leading provider of specialised system solutions for the georeferenced collection and refinement of civil infrastructure information Encardio-rite is sole agent in India of Amberg for its Tunnel Seismic Prediction Services. Advance notice of lithological heterogeneity and any variation in mechanical rock properties which could affect tunneling is an important factor. Such early warning makes it possible to ensure that counter-measures and logistic procedures are planned in good time. Continuous, high-quality predictions enable the management of risks inherent in tunneling.
Continuous prediction ahead of the face Gain time for construction and logistical counter-measures Minimise the downtime risk of expensive tunneling equipment Improve safety Profit from shorter construction times and cost savings
TSP 203PLUS
TSP 203 PLUS Tunnel seismic prediction system solution is specifically developed for underground construction. It evaluates seismic echo signals reflected from changes in the elastic rock characteristics normally associated with discontinuities in rock mass. It provides accurate spatial information concerning the geology and rock mechanical properties in front of and in the vicinity of the face.
Features
l l l l l l l
Ready to measure within 30 minutes Prediction range up to several hundred metres Can be used in both TBM and conventional headings Easy non-obstructing integration in the construction operation Spatial positioning of fault zones and potentially water-bearing features [3-component seismic sensors (P- and S-waves)] Fully independent battery operation Built for the roughest site conditions
31