Professional Documents
Culture Documents
Installation Instructions: Parts List
Installation Instructions: Parts List
Installation Instructions: Parts List
2 Well nuts
Left latch
3 Center tubes
2 Upright bars
Right latch
6 Threaded wedges
6 Non-threaded wedges
2 Snap-screws
© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 40695 (0810) 08L26-SJC-1A00-91 1 of 6
Left bracket (with latch) INSTALLATION
NOTE:
Right bracket (with latch) Do not damage the body paint finish.
Installing the Bed Extender
1. Using an awl, pierce through the seals in the holes
on the left side bed lining.
LEFT SIDE
BED LINING
Template
HEX
BOLTS
10 mm Socket
2. Install the left latch to the left side bed lining with
T-20 Torx wrench three hex bolts.
T-50 Torx wrench
Tape measure
Drill
3 mm and 8 mm Drill bits
Center punch
Eye protection (face shield, safety goggles, etc.)
Phillips screwdriver
Felt-tip pen
Awl
4 mm Hex wrench
File
2 of 6 AII 40695 (0810) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.
3. Remove the left front lower tie-down hook (two T-50 6. On the left side of the tailgate, position the template
torx bolts). to the tailgate as shown.
FRONT TAILGATE
T-50 TORX LEFT FRONT
BOLTS LOWER
TIE-DOWN HOOK
Align.
HOLE
TEMPLATE
CENTER
PUNCH
7D0957AB
4. Reinstall the left front lower tie-down hook and the 8. Using a felt-tip pen, mark the right side of the tailgate
left bracket with two T-50 torx bolts (reused). at the center of the triangular plain surface as shown.
TAILGATE
MARK
LEFT FRONT LOWER TRIANGULAR
TIE-DOWN HOOK 7D0956AB 7D0958AB
PLAIN SURFACE
5. Repeat steps 1 through 4 on the right side of the 9. Using a center punch, mark the tailgate at the mark
vehicle. made in step 8.
© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 40695 (0810) 3 of 6
10. While wearing eye protection, drill a 3 mm hole at the 14. Insert three center tubes to the left tube.
mark on the left side of the tailgate. Widen the hole
with a 8 mm drill bit. To prevent damage to the inner
LEFT
vehicle parts, wrap a tape around the drill bit tip to TUBE
the root in the measurement as shown. Remove any
burrs.
TAILGATE
MARK
3 CENTER
TUBES
DRILL
DRILL BIT
TIP TUBE RETAINER
10 mm Install if necessary.
(0.4 in.)
3 mm
8 mm
DRILL BIT 7D0950CB
TAPE
15. Install the upright bar to the left tube. Make sure to
ROOT DRILL install the upright bar in the correct orientation.
7D0959AB
11. Secure one well nut into the hole made in step 10.
UPRIGHT
LEFT BAR
TUBE
TAILGATE
HOLE
WELL NUT
831201BD
WASHER
SNAP- 16. Repeat step 15 for the right tube.
7D0960AB
SCREW
12. Secure one snap-screw and one washer to the well
nut.
13. Repeat steps 10 through 12 on the right side of the
tailgate.
4 of 6 AII 40695 (0810) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.
17. Align the non-threaded wedge with the threaded 20. Open the tailgate.
wedge at three joints between the left and center
tubes, then secure the wedges with one T-20 torx
screw each. BED
EXTENDER
3 THREADED
WEDGES
PIVOT
RIGHT
LATCH
LEFT
3 CENTER LATCH
TUBES
PIVOT
TAILGATE 841801AX
LEFT
TUBE 21. Insert two pivots on the bed extender to the latches.
STRAP
Pull down.
7D0951CB
BED
18. Insert three center tubes to the right tube (with label). EXTENDER
OUTER
LEFT PROJECTION
TUBE
SNAP
1,270 mm
(50.00 in.)
STRAP
TAILGATE
SNAP
841802AX
3 CENTER OUTER
TUBES PROJECTION
RIGHT TUBE
(with label) 7D0952CB
© 2008 American Honda Motor Co., Inc. – All Rights Reserved. AII 40695 (0810) 5 of 6
24. Align the center tubes so that there is a consistent 25. Align the non-threaded wedge with the threaded
gap between the bed extender and the side bed wedge at three joints between the right and center
lining. tubes, then secure the wedges with one T-20 torx
screw each.
SIDE BED
LINING
LEFT SIDE 3 T-20 TORX 3 NON-THREADED
BED LINING SCREWS WEDGES
3 THREADED
WEDGES
BED
EXTENDER
3 CENTER
TUBES
BED EXTENDER
TAILGATE
841803AX
7D0953CB
6 of 6 AII 40695 (0810) © 2008 American Honda Motor Co., Inc. – All Rights Reserved.