Professional Documents
Culture Documents
3G Call Flow Scenarios
3G Call Flow Scenarios
3G Call Flow Scenarios
Messages Flow
CN Description
RRC Connection Request is the first message transmitted by the UE when setting up an RRC Connection to the network
RRC
RRC
RRC
The network transmits this message when the requested RRC connection cannot be accepted. This message is used by the network to accept the establishment of an RRC connection for a UE, including assignment of signalling link information, transport channel information and optionally physical channel information.
RRC
RRC conn setup complete Initial Direct transfer -CM service request(MO)
This message confirms the establishment of the RRC Connection by the UE. This message is used to initiate a signalling connection based on indication from the upper layers, and to transfer a NAS message This message is sent by UTRAN to transfer higher layer messages
MM NAS UE
MM NAS CN
Download Direct transfer -Authentication request Uplink direct transfer -Authentication response Authentication Failure
MM NAS UE
MM NAS UE
RRC-RNC
This message is sent by UE to UTRAN to deliver a calculated response to the network This message is sent by UE to UTRAN to indicate the authentication of network is failed This message is sent by UTRAN to start or reconfigure ciphering and/or integrity protection parameters
RRC-UE
This message is sent by UE to confirm the reconfiguration of ciphering and/or integrity protection
MM NAS-CN
CM Service Accept
This message is sent by UTRAN to UE to indicate that the requested service has been accepted This message is sent by the network to UE to indicate that the requested service cannot be provided This message is sent by UE to UTRAN to initiate the MO call This message is sent by UTRAN to UE to the calling mobile station to indicate that the requested call estb information has been received and no more call estb info will be accepted This message is sent by UTRAN to the UE to establish new radio bearer(s). It can also include modifications to the configurations of trch and/or phy chan
CC NAS-CN
Call proceeding
RRC-RNC
This message is sent by the UE to confirm the establishment of the radio bearer RRC-UE Radio Bearer setup complete
This message is sent by UE, if it does not support the configuration given by UTRAN
This message is sent by network to the calling mobile station to indicate that the called user alerting has been initiated This message is sent by UTRAN to calling mobile station to indicate call acceptence by the called user
This message is sent by UTRAN to indicate that the end to end connection is cleared This message is sent by UTRAN to indicate that the end to end connection is cleared This message is sent by UE to UTRAN to ack the offered connection
Direction
UE--> UTRAN
TM
CCCH
RACH
PRACH
UTRAN--UE
UM
CCCH
FACH
SCCPCH
UTRAN--UE
UM
CCCH
FACH
SCCPCH
UE---UTRAN
AM
DCCH
DCH
DPCH
UE---UTRAN
AM
DCCH
DCH
DPCH
UTRAN--UE
AM
DCCH
DCH
DPCH
UE---UTRAN
AM
DCCH
DCH
DPCH
AM UE---UTRAN
DCCH
DCH
DPCH
UTRAN--UE
AM
DCCH
DCH
DPCH
UE---UTRAN
AM
DCCH
DCH
DPCH
UTRAN--UE
AM
DCCH
DCH
DPCH
UTRAN--UE
AM
DCCH
DCH
DPCH
AM UE---UTRAN
DCCH
DCH
DPCH
AM UTRAN --UE
DCCH
DCH
DPCH
UTRAN-UE
AM
DCCH
DCH
DPCH
UE---UTRAN
AM
DCCH
DCH
DPCH
UE---UTRAN UTRAN--UE
AM AM
DCCH DCCH
DCH DCH
DPCH DPCH
UTRAN--UE
AM
DCCH
DCH
DPCH
UTRAN--UE
AM
DCCH
DCH
DPCH
UE---UTRAN
AM
DCCH
DCH
DPCH
UE---UTRAN
AM
DCCH
DCH
DPCH
Information elements
ONLY Mandatory Parameters here UE IE-Intial UE identity(TMSI,LAI),Establishment cause,Protocol error indicator,Domain Indicator Measurement IE-Access stratum release indicator.
UE IE-Initial UE identity,RRC transaction identifier,Reject cause,wait time UE IE-Initial UE identity,RRC transaction identifier,New-U-RNTI,RRC state indicator RB IE-SRB info to setup list and SRB info to setup UL Transport channel:Added or Reconfig Trch and UL Trch information. DL Transport channel:Added or Reconfig Trch and UL Trch information. UL RR:Max allowed uplink Tx power DL RR:DL information for each radio link. UE IE:RRC Transaction identifiers,CN Domain Identity,UE radio access capabilities,Inter RAT UE radio access capabilities UE IE-Integrity check info,PLMN identity CN IE-CN domain identity,NAS message,Establishment cause,CS call type UE IE-Integrity check info,RRC transaction identifier,RAND,AUTN,Auth req msg type,ciphering key sequence number CN IE-CN domain identity,NAS message UE IE-Integrity check info,Auth response msg type,Auth response parameter (RES) CN IE-CN domain identity,NAS message MM protocol descriminator,Authentication failure message type,Reject cause,Auth failure parameters UE IE-Integrity check info,RRC transaction identifier,cipher mode info,security capability,integrity protection mode info. CN IE-CN domain identity,Inter RAT UE security capabilties
UE IE-Integrity check info,UL integrity protection activation info,RRC Transaction identifier. RB IE-Radio bearer uplink ciphering activation time info MM protocol descriminator,skip indicator,CM service accept message type MM protocol descriminator,skip indicator,CM service reject message type,reject cause Setup message type,called party BCD number,bearer cap 1,Transaction identifier,call control protocol descriminator Call control protocol descriminator,call proceeding message type,Transaction identifier
UE IE-Initial UE identity,RRC transaction identifier,New-U-RNTI,RRC state indicator RB IE-SRB info to setup list and SRB info to setup,RAB info for setup,RB info with PDCP UL Transport channel:Added or Reconfig ,deleted Trch and UL Trch information. DL Transport channel:Added or Reconfig Trch and UL Trch information. UL RR:Max allowed uplink Tx power DL RR:DL information for each radio link. UE IE-Integrity check info,UL integrity protection activation info,RRC Transaction identifier. RB IE-Radio bearer with PDCP info,CN domain identiy UE IE-Integrity check info,RRC Transaction identifier,Failure cause RB IE-Radio bearer for which reconfiguration has been suceeded. Transaction identifier,Alerting message type
call control protocol descriminator,Transaction identifier,disconnect message type,cause call control protocol descriminator,Transaction identifier,disconnect message type,cause call control protocol descriminator,Transaction identifier,connect acknowledge message type
Message Trigg UE by
Messages Flow
CN
RRC-UE
RRC-RNC
RRC-RNC
RRC-UE
MM NAS UE
MM NAS CN
Download Direct transfer -Authentication request Uplink direct transfer -Authentication response Authentication Failure
MM NAS UE
MM NAS UE
RRC-RNC
RRC-UE
MM NAS-CN
MM NAS-CN
MM NAS-UE
RRC-RNC
RRC-UE
Description
RRC Connection Request is the first message transmitted by the UE when setting up an RRC Connection to the network The network transmits this message when the requested RRC connection cannot be accepted.
SRB
Direction
RLC-SAP
SRB-0
UE--> UTRAN
TM
SRB-0
UTRAN--UE
UM
This message is used by the network to accept the establishment of an RRC connection for a UE, including assignment of signalling link information, transport channel information and optionally physical channel information.
SRB-0
UTRAN--UE
UM
This message confirms the establishment of the RRC Connection by the UE. This message is sent by the mobile station to the network either to request update of its location file (normal updating or periodic updating) or to request IMSI attach. This message is sent by UTRAN to transfer higher layer messages This message is sent by UE to UTRAN to deliver a calculated response to the network This message is sent by UE to UTRAN to indicate the authentication of network is failed This message is sent by UTRAN to start or reconfigure ciphering and/or integrity protection parameters
SRB-2
UE---UTRAN
AM
SRB-3
UE---UTRAN
AM
SRB-3
UTRAN--UE
AM
SRB-3
UE---UTRAN
AM
SRB-3
UE---UTRAN
AM
SRB-2
UTRAN--UE
AM
This message is sent by UE to confirm the reconfiguration of ciphering and/or integrity protection This message is sent by the network to the mobile station to indicate that updating or IMSI attach in the network has been completed. This message is sent by the network to the mobile station to indicate that updating or IMSI attach has failed. This message is sent by the mobile station to the network to indicate that reallocation or deletion of a TMSI has taken place. This message is sent by UTRAN to release the RRC connection. The message also releases the signalling connection and all radio bearers between the UE and UTRAN. This message is sent by UE to confirm that the RRC connection has been released.
SRB-2
UE---UTRAN
AM
SRB-3
UTRAN--UE
AM
SRB-3
UTRAN--UE
AM
SRB-3
UE---UTRAN
AM
SRB-2
UTRAN --UE
UM
SRB-2
UE---UTRAN
UM
Logical Chnl
CCCH
RACH
PRACH
CCCH
FACH
SCCPCH
CCCH
FACH
SCCPCH
DCCH
DCH
DPCH
DCCH
DCH
DPCH
DCCH
DCH
DPCH
DCCH
DCH
DPCH
DCCH
DCH
DPCH
DCCH
DCH
DPCH
DCCH
DCH
DPCH
DCCH
DCH
DPCH
DCCH
DCH
DPCH
DCCH
DCH
DPCH
DCCH/CCCH(Cell FACH)
DCH
DPCH
DCCH/CCCH(Cell FACH)
DCH
DPCH
Information elements
ONLY Mandatory Parameters here UE IE-Intial UE identity(TMSI,LAI),Establishment cause,Protocol error indicator,Domain Indicator Measurement IE-Access stratum release indicator.
UE IE-Initial UE identity,RRC transaction identifier,Reject cause,wait time UE IE-Initial UE identity,RRC transaction identifier,New-U-RNTI,RRC state indicator RB IE-SRB info to setup list and SRB info to setup UL Transport channel:Added or Reconfig Trch and UL Trch information. DL Transport channel:Added or Reconfig Trch and UL Trch information. UL RR:Max allowed uplink Tx power DL RR:DL information for each radio link. UE IE:RRC Transaction identifiers,CN Domain Identity,UE radio access capabilities,Inter RAT UE radio access capabilities Mobility management protocol discriminator, Skip Indicator, Location Updating,Request message type,Location updating type,Ciphering key sequence,Location area,Mobile station classmark,Mobile identity. UE IE-Integrity check info,RRC transaction identifier,RAND,AUTN,Auth req msg type,ciphering key sequence number CN IE-CN domain identity,NAS message UE IE-Integrity check info,Auth response msg type,Auth response parameter (RES) CN IE-CN domain identity,NAS message MM protocol descriminator,Authentication failure message type,Reject cause,Auth failure parameters UE IE-Integrity check info,RRC transaction identifier,cipher mode info,security capability,integrity protection mode info. CN IE-CN domain identity,Inter RAT UE security capabilties
UE IE-Integrity check info,UL integrity protection activation info,RRC Transaction identifier. RB IE-Radio bearer uplink ciphering activation time info Mobility management protocol discriminator, Skip Indicator,Location Updating Accept message type,Location area identification. MM protocol descriminator,skip indicator, Location Updating Reject message type,Reject cause Mobility management protocol discriminator, Skip Indicator, TMSI Reallocation Complete message type
Message Type,UE information elements:- URNTI,RRC transaction identifier,Integrity check info,N308(CH Cell_DCH),Release cause. Message Type,UE information elements:- RRC transaction identifier,Integrity check info,Error indication
Message Trigg UE by
Messages Flow
CN
RRC-UE
RRC-RNC
RRC-RNC
RRC-UE
GMM NAS UE
GMM NAS CN
Download Direct transfer -Authentication request Uplink direct transfer -Authentication response Authentication Failure
GMM NAS UE
GMM NAS UE
RRC-RNC
RRC-UE
GMM NAS-CN
Attach Accept
GMM NAS-CN
Attach Reject
GMM NAS-UE
Attach Complete
RRC-RNC
RRC-UE
Description
RRC Connection Request is the first message transmitted by the UE when setting up an RRC Connection to the network The network transmits this message when the requested RRC connection cannot be accepted.
SRB
Direction
RLC-SAP
SRB-0
UE--> UTRAN
TM
SRB-0
UTRAN--UE
UM
This message is used by the network to accept the establishment of an RRC connection for a UE, including assignment of signalling link information, transport channel information and optionally physical channel information.
SRB-0
UTRAN--UE
UM
This message confirms the establishment of the RRC Connection by the UE.
SRB-2
UE---UTRAN
AM
This message is sent by the MS to the network in order to perform a GPRS or combined GPRS attach.
SRB-3
UE---UTRAN
AM
This message is sent by UTRAN to transfer higher layer messages This message is sent by UE to UTRAN to deliver a calculated response to the network This message is sent by UE to UTRAN to indicate the authentication of network is failed
SRB-3
UTRAN--UE
AM
SRB-3
UE---UTRAN
AM
SRB-3
UE---UTRAN
AM
This message is sent by UTRAN to start or reconfigure ciphering and/or integrity protection parameters
SRB-2
UTRAN--UE
AM
This message is sent by UE to confirm the reconfiguration of ciphering and/or integrity protection
SRB-2
UE---UTRAN
AM
This message is sent by the network to the MS to indicate that the corresponding attach request has been accepted. This message is sent by the network to the MS to indicate that the corresponding attach request has been rejected. This message is sent by the MS to the network if a P-TMSI and/or a TMSI was included within the attach accept message. This message is sent by UTRAN to release the RRC connection. The message also releases the signalling connection and all radio bearers between the UE and UTRAN. This message is sent by UE to confirm that the RRC connection has been released.
SRB-3
UTRAN--UE
AM
SRB-3
UTRAN--UE
AM
SRB-3
UE---UTRAN
AM
SRB-2
UTRAN --UE
UM
SRB-2
UE---UTRAN
UM
Logical Chnl
CCCH
RACH
PRACH
CCCH
FACH
SCCPCH
CCCH
FACH
SCCPCH
DCCH
DCH
DPCH
DCCH
DCH
DPCH
DCCH
DCH
DPCH
DCCH
DCH
DPCH
DCCH
DCH
DPCH
DCCH
DCH
DPCH
DCCH
DCH
DPCH
DCCH
DCH
DPCH
DCCH
DCH
DPCH
DCCH
DCH
DPCH
DCCH/CCCH(Cell FACH)
DCH
DPCH
DCCH/CCCH(Cell FACH)
DCH
DPCH
Information elements
ONLY Mandatory Parameters here UE IE-Intial UE identity(TMSI,LAI),Establishment cause,Protocol error indicator,Domain Indicator Measurement IE-Access stratum release indicator.
UE IE-Initial UE identity,RRC transaction identifier,Reject cause,wait time UE IE-Initial UE identity,RRC transaction identifier,New-U-RNTI,RRC state indicator RB IE-SRB info to setup list and SRB info to setup UL Transport channel:Added or Reconfig Trch and UL Trch information. DL Transport channel:Added or Reconfig Trch and UL Trch information. UL RR:Max allowed uplink Tx power DL RR:DL information for each radio link. UE IE:RRC Transaction identifiers,CN Domain Identity,UE radio access capabilities,Inter RAT UE radio access capabilities Mobility management protocol discriminator, Skip Indicator, Attach request message identity,Attach request message identity,Attach type ,GPRS ciphering key sequence number,DRX parameter,P-TMSI or IMSI,Old routing area identification,MS Radio Access capability UE IE-Integrity check info,RRC transaction identifier,RAND,AUTN,Auth req msg type,ciphering key sequence number CN IE-CN domain identity,NAS message UE IE-Integrity check info,Auth response msg type,Auth response parameter (RES) CN IE-CN domain identity,NAS message MM protocol descriminator,Authentication failure message type,Reject cause,Auth failure parameters
UE IE-Integrity check info,RRC transaction identifier,cipher mode info,security capability,integrity protection mode info. CN IE-CN domain identity,Inter RAT UE security capabilties UE IE-Integrity check info,UL integrity protection activation info,RRC Transaction identifier. RB IE-Radio bearer uplink ciphering activation time info Mobility management protocol discriminator, Skip Indicator,Attach accept message identity, Attach result,Force to standby,Periodic RA update timer,Radio priority for SMS,Spare half octet,Routing area identification MM protocol descriminator,skip indicator, Attach reject message identity,GMM cause.
Mobility management protocol discriminator, Skip Indicator, Attach complete message identity.
Message Type,UE information elements:- URNTI,RRC transaction identifier,Integrity check info,N308(CH Cell_DCH),Release cause. Message Type,UE information elements:- RRC transaction identifier,Integrity check info,Error indication
Message Trigg UE by
Messages Flow
RNC
RRC-RNC
MEASUREMENT CONTROL
RRC-UE
RRC-UE
MEASUREMENT REPORT
RRC-RNC
RRC-UE
RRC-UE
Soft
RRC-RNC
MEASUREMENT CONTROL
RRC-UE
RRC-UE
MEASUREMENT REPORT
RRC-RNC
RRC-UE
RRC-UE
Sof
Description
Direction
SRB
RLC-SAP
This message is sent by UTRAN to setup, modify or release a measurement in the UE.
UTRAN--UE(DOWNLINK)
SRB-2
AM
This message is sent by UE, if it cannot initiate a measurement as instructed by UTRAN. This message is used by UE to transfer measurement results to the UTRAN.
UE---UTRAN(UPLINK)
SRB-2
AM
UE---UTRAN(UPLINK)
SRB1 or SRB2
AM/UM
This message is used by UTRAN to add, replace or delete radio links in the active set of the UE.
UTRAN--UE(DOWNLINK)
SRB1 or SRB2
AM/UM
This message is sent by UE if the update of the active set has failed, e.g. because the radio link is not a part of the active set. This message is sent by UE when active set update has been completed.
UE---UTRAN(UPLINK)
SRB-2
AM
UE---UTRAN(UPLINK)
SRB-2
AM
This message is sent by UTRAN to setup, modify or release a measurement in the UE.
UTRAN--UE
SRB-2
AM
This message is sent by UE, if it cannot initiate a measurement as instructed by UTRAN. This message is used by UE to transfer measurement results to the UTRAN.
UE---UTRAN
SRB-2
AM
UE---UTRAN
SRB1 or SRB2
AM/UM
This message is used by UTRAN to add, replace or delete radio links in the active set of the UE.
UTRAN--UE
SRB1 or SRB2
AM/UM
This message is sent by UE if the update of the active set has failed, e.g. because the radio link is not a part of the active set. This message is sent by UE when active set update has been completed.
UE---UTRAN
SRB-2
AM
UE---UTRAN
SRB-2
AM
Logical Chnl
DCCH
DCH/FACH
DPCH/S-CCPCH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/FACH
DPCH/S-CCPCH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/RACH
DPCH/PRACH
dition(Above)
DCCH
DCH/FACH
DPCH/S-CCPCH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/FACH
DPCH/S-CCPCH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/RACH
DPCH/PRACH
etion(Above)
Information elements
Message Type,UE information elements:-RRC transaction identifier,Integrity check info,Measurement Information elements:-Measurement Identity,Measurement Command,CHOICE Measurement type:-Intrafrequency measurement,Inter-frequency measurement,Inter-RAT measurement,UE positioning measurement,Traffic Volume measurement,Quality measurement,UE internal measurement Message Type,RRC transaction identifier,Failure cause. Message Type(Event1a),Measurement Information Elements:-Measurement identity,Measured Results. Message Type,UE information elements:-RRC transaction identifier,Activation time,Phy CH information elements Uplink radio resources:Maximum allowed UL TX power,Radio link addition information,Radio link removal information,TX Diversity Mode Message Type,UE information elements:-RRC transaction identifier,Failure cause
Message Type,UE information elements:-RRC transaction identifier,Integrity check info,Measurement Information elements:-Measurement Identity,Measurement Command,CHOICE Measurement type:-Intrafrequency measurement,Inter-frequency measurement,Inter-RAT measurement,UE positioning measurement,Traffic Volume measurement,Quality measurement,UE internal measurement
Message Type,RRC transaction identifier,Failure cause. Message Type(Event1b),Measurement Information Elements:-Measurement identity,Measured Results. Message Type,UE information elements:-RRC transaction identifier,Activation time,Phy CH information elements Uplink radio resources:Maximum allowed UL TX power,Radio link addition information,Radio link removal information,TX Diversity Mode Message Type,UE information elements:-RRC transaction identifier,Failure cause
Message Trigg UE by
Messages Flow
RNC
RRC-RNC
MEASUREMENT CONTROL
RRC-UE
RRC-UE
MEASUREMENT REPORT
RRC-RNC
RRC-UE
RRC-UE
RRC-RNC
MEASUREMENT CONTROL
RRC-UE
RRC-UE
MEASUREMENT REPORT
RRC-RNC
RRC-UE
RRC-UE
Description
Direction
SRB
RLC-SAP
This message is sent by UTRAN to setup, modify or release a measurement in the UE.
UTRAN--UE(DOWNLINK)
SRB-2
AM
This message is sent by UE, if it cannot initiate a measurement as instructed by UTRAN. This message is used by UE to transfer measurement results to the UTRAN.
UE---UTRAN(UPLINK)
SRB-2
AM
UE---UTRAN(UPLINK)
SRB1 or SRB2
AM/UM
This message is used by UTRAN to add, replace or delete radio links in the active set of the UE.
UTRAN--UE(DOWNLINK)
SRB1 or SRB2
AM/UM
This message is sent by UE if the update of the active set has failed, e.g. because the radio link is not a part of the active set. This message is sent by UE when active set update has been completed.
UE---UTRAN(UPLINK)
SRB-2
AM
UE---UTRAN(UPLINK)
SRB-2
AM
This message is sent by UTRAN to setup, modify or release a measurement in the UE.
UTRAN--UE
SRB-2
AM
This message is sent by UE, if it cannot initiate a measurement as instructed by UTRAN. This message is used by UE to transfer measurement results to the UTRAN.
UE---UTRAN
SRB-2
AM
UE---UTRAN
SRB1 or SRB2
AM/UM
This message is used by UTRAN to add, replace or delete radio links in the active set of the UE.
UTRAN--UE
SRB1 or SRB2
AM/UM
This message is sent by UE if the update of the active set has failed, e.g. because the radio link is not a part of the active set. This message is sent by UE when active set update has been completed.
UE---UTRAN
SRB-2
AM
UE---UTRAN
SRB-2
AM
Logical Chnl
DCCH
DCH/FACH
DPCH/S-CCPCH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/FACH
DPCH/S-CCPCH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/RACH
DPCH/PRACH
bove)
DCCH
DCH/FACH
DPCH/S-CCPCH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/FACH
DPCH/S-CCPCH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/RACH
DPCH/PRACH
bove)
Information elements
Message Type,UE information elements:-RRC transaction identifier,Integrity check info,Measurement Information elements:-Measurement Identity,Measurement Command,CHOICE Measurement type:-Intrafrequency measurement,Inter-frequency measurement,Inter-RAT measurement,UE positioning measurement,Traffic Volume measurement,Quality measurement,UE internal measurement Message Type,RRC transaction identifier,Failure cause. Message Type(Event1a),Measurement Information Elements:-Measurement identity,Measured Results. Message Type,UE information elements:-RRC transaction identifier,Activation time,Phy CH information elements Uplink radio resources:Maximum allowed UL TX power,Radio link addition information,Radio link removal information,TX Diversity Mode Message Type,UE information elements:-RRC transaction identifier,Failure cause
Message Type,UE information elements:-RRC transaction identifier,Integrity check info,Measurement Information elements:-Measurement Identity,Measurement Command,CHOICE Measurement type:-Intrafrequency measurement,Inter-frequency measurement,Inter-RAT measurement,UE positioning measurement,Traffic Volume measurement,Quality measurement,UE internal measurement Message Type,RRC transaction identifier,Failure cause. Message Type(Event1b),Measurement Information Elements:-Measurement identity,Measured Results. Message Type,UE information elements:-RRC transaction identifier,Activation time,Phy CH information elements Uplink radio resources:Maximum allowed UL TX power,Radio link addition information,Radio link removal information,TX Diversity Mode Message Type,UE information elements:-RRC transaction identifier,Failure cause
Message Trigg UE by
Messages Flow
RNC
RRC-RNC
RRC-RNC
RRC-RNC
RRC-RNC
RRC-UE
RRC-UE
RRC-RNC
RRC-UE
RRC-RNC
MEASUREMENT CONTROL
RRC-UE
RRC-UE
RRC-UE
MEASUREMENT REPORT
RRC-UE
MEASUREMENT REPORT
RRC-RNC
MEASUREMENT CONTROL
RRC-UE
RRC-UE
MEASUREMENT REPORT
RRC-UE
RRC-RNC
RRC-UE
RR-UE
HANDOVER ACCESS
BSC
RRC-UE
HANDOVER COMPLETE
BSC
Description
Direction
SRB
RLC-SAP
This message is sent by UTRAN to setup, modify or release a measurement in the UE.
UTRAN--UE(DOWNLINK)
SRB-2
AM
This message is sent by UTRAN to setup, modify or release a measurement in the UE.
UTRAN--UE(DOWNLINK)
SRB-2
AM
This message is sent by UTRAN to setup, modify or release a measurement in the UE.
UTRAN--UE(DOWNLINK)
SRB-2
AM
This message is sent by UTRAN to setup, modify or release a measurement in the UE.
UTRAN--UE(DOWNLINK)
SRB-2
AM
This message is sent by UE, if it cannot initiate a measurement as instructed by UTRAN. This message is used by UE to transfer measurement results to the UTRAN.
UE---UTRAN(UPLINK)
SRB-2
AM
UE---UTRAN(UPLINK)
SRB1 or SRB2
AM/UM
This message is used by UTRAN to assign, replace or release a set of physical channels used by a UE.
UTRAN--UE(DOWNLINK)
SRB1 or SRB2
AM/UM
This message is sent by UE if the configuration given by UTRAN is unacceptable or if the UE failed to assign, replace or release a set of physical channel(s).
UE---UTRAN(UPLINK)
SRB-2
AM
This message is sent by UTRAN to setup, modify or release a measurement in the UE.
UTRAN--UE(DOWNLINK)
SRB-2
AM
UE---UTRAN(UPLINK)
SRB-2
AM
This message is sent by UE when active set update has been completed.
UE---UTRAN(UPLINK)
SRB-2
AM
This message is used by UE to transfer measurement results to the UTRAN. This message is used by UE to transfer measurement results to the UTRAN.
UE---UTRAN(UPLINK)
SRB1 or SRB2
AM/UM
UE---UTRAN(UPLINK)
SRB1 or SRB2
AM/UM
This message is sent by UTRAN to setup, modify or release a measurement in the UE.
UTRAN--UE(DOWNLINK)
SRB-2
AM
This message is sent by UE, if it cannot initiate a measurement as instructed by UTRAN. This message is used by UE to transfer measurement results to the UTRAN. This message is used by UE to transfer measurement results to the UTRAN.
UE---UTRAN(UPLINK)
SRB-2
AM
UE---UTRAN(UPLINK)
SRB1 or SRB2
AM/UM
UE---UTRAN(UPLINK)
SRB1 or SRB2
AM/UM
This message is used for handover from UMTS to another system e.g. GSM. One or several messages from the other system can be included in the Inter-RAT message information element in this message. These messages are structured and coded according to that systems specification. This message is sent on the RRC connection used before the Inter-RAT Handover was executed. The message indicates that the UE has failed to seize the new channel in the other system. In case of the synchronized handover, the MS sends up to four HND_ACC messages to the BTS when receiving the HND_CMD (this applies to intra-BSC as well). The data of a HND_ACC message is only one byte long and carries the handover reference, that is, the temporary identifier of the MS.If the assignment procedure is used for the intra-BTS handover,then sending of the HND_ACC messages is not necessary.
UTRAN--UE(DOWNLINK)
SRB2
AM
UE---UTRAN(UPLINK)
SRB-2
AM
UE--BSC
The MS confirms handover by sending of HND_COM . Only now, the MSC receives the information in a HND_PERF message that a handover was performed by the BSS. This message is sent on the main DCCH from the mobile station to the network to indicate that the mobile station has established the main signalling link successfully.
UE--BSC
Logical Chnl
DCCH
DCH/FACH
DPCH/S-CCPCH
DCCH
DCH/FACH
DPCH/S-CCPCH
DCCH
DCH/FACH
DPCH/S-CCPCH
DCCH
DCH/FACH
DPCH/S-CCPCH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/FACH
DPCH/S-CCPCH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/FACH
DPCH/S-CCPCH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/FACH
DPCH/S-CCPCH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/RACH
DPCH/PRACH
DCCH
DCH/FACH
DPCH/S-CCPCH
DCCH
DCH/RACH
DPCH/PRACH
Information elements
Message Type,UE information elements:-RRC transaction identifier,Integrity check info,Measurement Information elements:-Measurement Identity,Measurement Command,CHOICE Measurement type:-Intrafrequency measurement,Inter-frequency measurement,Inter-RAT measurement,UE positioning measurement,Traffic Volume measurement,Quality measurement,UE internal measurement Message Type,UE information elements:-RRC transaction identifier,Integrity check info,Measurement Information elements:-Measurement Identity,Measurement Command,CHOICE Measurement type:-Intrafrequency measurement,Inter-frequency measurement,Inter-RAT measurement,UE positioning measurement,Traffic Volume measurement,Quality measurement,UE internal measurement Message Type,UE information elements:-RRC transaction identifier,Integrity check info,Measurement Information elements:-Measurement Identity,Measurement Command,CHOICE Measurement type:-Intrafrequency measurement,Inter-frequency measurement,Inter-RAT measurement,UE positioning measurement,Traffic Volume measurement,Quality measurement,UE internal measurement
Message Type,UE information elements:-RRC transaction identifier,Integrity check info,Measurement Information elements:-Measurement Identity,Measurement Command,CHOICE Measurement type:-Intrafrequency measurement,Inter-frequency measurement,Inter-RAT measurement,UE positioning measurement,Traffic Volume measurement,Quality measurement,UE internal measurement Message Type,RRC transaction identifier,Failure cause. Message Type(Event1a),Measurement Information Elements:-Measurement identity,Measured Results. Message Type,UE information elements:-RRC transaction identifier,Activation time,RRC State Indicator,UTRAN mobility information elements:-RB with PDCP information Uplink radio resources:-Maximum allowed UL TX power,Downlink radio resources:-CHOICE mode,Downlink information for each radio link
Message Type,UE information elements:-RRC transaction identifier,Integrity check info,Measurement Information elements:-Measurement Identity,Measurement Command,CHOICE Measurement type:-Intrafrequency measurement,Inter-frequency measurement,Inter-RAT measurement,UE positioning measurement,Traffic Volume measurement,Quality measurement,UE internal measurement
Message Type,RRC transaction identifier,Failure cause. Message Type,UE information elements:-RRC transaction identifier,CHOICE mode,FDD or TDD,CHOICE TDD option,Information Element/Group name:-RB with PDCP information,START list,CN domain identity,START(START value to be used in this CN domain.) Message Type(Event1a),Measurement Information Elements:-Measurement identity,Measured Results. Message Type(Event1a),Measurement Information Elements:-Measurement identity,Measured Results. Message Type,UE information elements:-RRC transaction identifier,Integrity check info,Measurement Information elements:-Measurement Identity,Measurement Command,CHOICE Measurement type:-Intrafrequency measurement,Inter-frequency measurement,Inter-RAT measurement,UE positioning measurement,Traffic Volume measurement,Quality measurement,UE internal measurement Message Type,RRC transaction identifier,Failure cause. Message Type(Event1a),Measurement Information Elements:-Measurement identity,Measured Results. Message Type(Event1a),Measurement Information Elements:-Measurement identity,Measured Results.
Message Type,UE information elements:-RRC transaction identifier,Activation time,RAB info,Other information elements:-CHOICE System type,GSM Frequency band,GSM message:-Single GSM message,GSM message List,cdma2000:cdma2000MessageList,MSG_TYPE(s),cdma2000Mes sagepayload(s)
Message Type,UE information elements:-RRC transaction identifier,GSM message:-GSM message List,cdma2000:cdma2000MessageList,MSG_TYPE(s),cdma2000Mes sagepayload(s)
Message Trigg UE by
RRC-RNC Through TMSI
Messages Flow
CN
Description
This message is used to send information on the paging channel. One or several UEs, in idle or connected mode, can be paged in one message, which also can contain other information. This message is used to page a UE in connected mode, when using the DCCH for CN originated paging.
Paging Type 1
Paging Type 2
RRC-UE
RRC Connection Request is the first message transmitted by the UE when setting up an RRC Connection to the network The network transmits this message when the requested RRC connection cannot be accepted.
RRC-RNC
RRC-RNC
This message is used by the network to accept the establishment of an RRC connection for a UE, including assignment of signalling link information, transport channel information and optionally physical channel information.
RRC-UE
RRC conn setup complete Initial Direct transfer -Paging Response(MT CALL)
This message confirms the establishment of the RRC Connection by the UE.
MM NAS UE
MM NAS CN
Download Direct transfer -Authentication request Uplink direct transfer -Authentication response
This message is sent by UTRAN to transfer higher layer messages This message is sent by UE to UTRAN to deliver a calculated response to the network
MM NAS UE
MM NAS UE
Authentication Failure
This message is sent by UE to UTRAN to indicate the authentication of network is failed This message is sent by UTRAN to start or reconfigure ciphering and/or integrity protection parameters
RRC-RNC
RRC-UE
This message is sent by UE to confirm the reconfiguration of ciphering and/or integrity protection This message is sent by UTRAN to initiate the MT call This message is sent by the called mobile station to confirm an incoming call request
CC NAS-UE
Setup
CC NAS-CN
Call confirmed
RRC-RNC
This message is sent by UTRAN to the UE to establish new radio bearer(s). It can also include modifications to the configurations of trch and/or phy chan
RRC-UE
This message is sent by the UE to confirm the establishment of the radio bearer
RRC-UE
This message is sent by UE, if it does not support the configuration given by UTRAN This message is sent by the called mobile station to the network to indicate that the called user alerting has been initiated This message is sent by the called mobile station to the network to indicate call acceptence by the called user
NAS-CC
Alerting
NAS-CC
Connect
NAS-CC
Disconnect
This message is sent by UTRAN to indicate that the end to end connection is cleared This message is sent by UTRAN to indicate that the end to end connection is cleared This message is sent by UTRAN to UE to ack the offered connection
NAS-CC
Disconnect
NAS-CC
Connect Acknowledge
Direction
UTRAN--UE
TM
PCCH
PCH
SCCPCH
UTRAN-UE
AM
DCCH
DCH
DPCH
UE--> UTRAN
TM
CCCH
RACH
PRACH
UTRAN--UE
UM
CCCH
FACH
SCCPCH
UTRAN--UE
UM
CCCH
FACH
SCCPCH
UE---UTRAN
AM
DCCH
DCH
DPCH
UE---UTRAN
AM
DCCH
DCH
DPCH
UTRAN--UE
AM
DCCH
DCH
DPCH
UE---UTRAN
AM
DCCH
DCH
DPCH
UE---UTRAN
AM
DCCH
DCH
DPCH
UTRAN--UE
AM
DCCH
DCH
DPCH
UE---UTRAN
AM
DCCH
DCH
DPCH
UTRAN --UE
AM
DCCH
DCH
DPCH
UE--UTRAN
AM
DCCH
DCH
DPCH
UTRAN-UE
AM
DCCH
DCH
DPCH
UE---UTRAN
AM
DCCH
DCH
DPCH
UE---UTRAN
AM
DCCH
DCH
DPCH
UE---UTRAN
AM
DCCH
DCH
DPCH
UE---UTRAN
AM
DCCH
DCH
DPCH
UTRAN--UE
AM
DCCH
DCH
DPCH
UE---UTRAN
AM
DCCH
DCH
DPCH
UTRAN--UE
AM
DCCH
DCH
DPCH
Information elements
Message type ,integrity check info,rrc transaction identifier,CN domain identity,paging cause
ONLY Mandatory Parameters here UE IE-Intial UE identity(TMSI,LAI),Establishment cause,Protocol error indicator,Domain Indicator Measurement IE-Access stratum release indicator.
UE IE-Initial UE identity,RRC transaction identifier,Reject cause,wait time UE IE-Initial UE identity,RRC transaction identifier,New-U-RNTI,RRC state indicator RB IE-SRB info to setup list and SRB info to setup UL Transport channel:Added or Reconfig Trch and UL Trch information. DL Transport channel:Added or Reconfig Trch and UL Trch information. UL RR:Max allowed uplink Tx power DL RR:DL information for each radio link. UE IE:RRC Transaction identifiers,CN Domain Identity,UE radio access capabilities,Inter RAT UE radio access capabilities
UE IE-Integrity check info,RRC transaction identifier,RAND,AUTN,Auth req msg type,ciphering key sequence number CN IE-CN domain identity,NAS message UE IE-Integrity check info,Auth response msg type,Auth response parameter (RES) CN IE-CN domain identity,NAS message
MM protocol descriminator,Authentication failure message type,Reject cause,Auth failure parameters UE IE-Integrity check info,RRC transaction identifier,cipher mode info,security capability,integrity protection mode info. CN IE-CN domain identity,Inter RAT UE security capabilties UE IE-Integrity check info,UL integrity protection activation info,RRC Transaction identifier. RB IE-Radio bearer uplink ciphering activation time info Setup message type,called party BCD number,bearer cap 1,Transaction identifier,call control protocol descriminator Call control protocol descriminator,call confirmed message type,CC capabilities UE IE-Initial UE identity,RRC transaction identifier,New-U-RNTI,RRC state indicator RB IE-SRB info to setup list and SRB info to setup,RAB info for setup,RB info with PDCP UL Transport channel:Added or Reconfig ,deleted Trch and UL Trch information. DL Transport channel:Added or Reconfig Trch and UL Trch information. UL RR:Max allowed uplink Tx power DL RR:DL information for each radio link. UE IE-Integrity check info,UL integrity protection activation info,RRC Transaction identifier. RB IE-Radio bearer with PDCP info,CN domain identiy UE IE-Integrity check info,RRC Transaction identifier,Failure cause RB IE-Radio bearer for which reconfiguration has been suceeded. Transaction identifier,Alerting message type,call control protocol discriminator
call control protocol descriminator,Transaction identifier,disconnect message type,cause call control protocol descriminator,Transaction identifier,disconnect message type,cause call control protocol descriminator,Transaction identifier,connect acknowledge message type