Professional Documents
Culture Documents
Programmable Encoder/Decoder: General Description
Programmable Encoder/Decoder: General Description
Programmable Encoder/Decoder: General Description
Programmable Encoder/Decoder
Single chip contains both Encoder and Decoder. 3V to 11 V operation. On chip oscillator uses non-critical RC components. Cross interference of recetver is virtually eliminated by circuitry which requires 4 valid words to be received, each within 64ms of the other.
Schmitt Trigger input provides excellent noise immunity. Applications. alarm control system, security system cordless telephone, remote control. Interfaces with RF, ultrasonic, or infrared modulators I and demodulators
General Description
T h e U M 3 7 5 0 E n c o d e r / D e c o d e r is a CMOS/LSI digital code Transmitter-Receiver system. Working in the transmit (encoder) mode, the UM3750 will sequentially encode and transmit 12 bits of input. Each of the 12 bits may be 1 or 0 to allow 4096 different codes. In the
comparison on the next word. If all 12 bits are received correctly, a valid signal is generated. This signal clears a 64ms counter and triggers a 3-stage counter. The 3-stage counter counts the valid pluses and when 4 pulses have been detected, the TX/RX output pin goes low. After the TX/RX output pin goes low, the next valid must be received within 128ms, giving a one valid in 6 requirement to keep the TX/RX output pin.
Pin Configurations
cc
cc
TX/RX OUTPUT RECEIVER INPUT MODE SELECT ss R.C INPUT A12 All A10
TX/RX
OUTPUT
2-3
urn3750
Block Diagram
R.C.INPUT - - - - - - -
CPCLK
RID I I
ERROR
WD TIM0 7 i VLD
MXCLKR
L
COMPARATOR MXD Al-Al2
64ms/128ms TIMER
STATE CONTROLLER
CLR INIT
I VALID 4 COUNTER
T/R OUT
Block Diagram Description CLK of Comparator CPCLK WXCLKR: CLK of Multiplexer when in Receiver mode WXCLKT CLK of Multiplexer when in Transmitter mode Output data of Multiplexer (one of Al, A2 .... MXD: RID VLD. A12) Sampled data by Sampling CKT Valid signal. It is used to trigger Valid 4 Counter and reset 64ms/128ms Timer Clear signal of Comparator CLR: Error signal from Comparator ERROR: TIMER time-out signal (64ms or 128ms) TIMO : T/R OUT: Transmit/Receiver output pin Reset signal of Valid 4 Counter INIT: Word detected signal WD: Transmitter output TXO: Receiver output PXO:
2-4
UM3750
Absolute Maximum Ratings*
P o w e r Operating S u p p l y V o l t a g e
*Comments
-0
3v to 11v
C
Stresses
Ratings These are may
Absolute to
Maximum dewce. of
Temperature
- 2 0 Deg to 70 D e g
damage
the
Functional
operation
this device at these or any other conditions above those indtcated in the operational sections of this specification a n d e x p o s u r e t o a b s o l u t e maximuln rating m a y a f f e c t d e v i c e rellIS not implled
vss
c o n d i t i o n s f o r e x t e n d e d pertods ability.
otherwise specified)
Input Level
200K
1.2M
Oscillator
Frequency
100
KHz
Pin Designation
Pin No.
l - 1 2
Designation
Al - Al2
Description
These data select lines are used to set the addresses of the encoder/decoder pair They have on-chip pull-up resistors. o s c i l l a t o r . A reslstor IS h o o k e d f r o m this pin to GND f r o m this
13
R.C. INPUT
R.C. 2lRC.
The frequency =
14 15
g r o u n d i n g this pin the IC IS p u t I n t o t h e R e c e i v e m o d e . B y c o n n e c t i n g to VC- the IC IS put into the Transmit 16 RECEIVER INPUT 17 TXIRX OUTPUT mode
T h e r e c e i v e r i n p u t r e c e i v e s t h e d i g i t a l P C M w a v e f o r m from the detect CIrClllt. In the transmit mode, this output pin transmlttlnq. produces the PCM waveform for
partson result and detects low If comparison is ok. 18 Vcc The positive power
2-5
UM3750
Typical
2-6
Decoder Flowchart
N O
Yes ? _!:_I-
No
No
Yes
TX,RX
Output
Ordering Information
Part No.
Package
2-7
This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.