Professional Documents
Culture Documents
Displaytech LTD.: LCD Module Product Specification
Displaytech LTD.: LCD Module Product Specification
LCD MODULE
64128K SERIES
Version : 1.2
P 1 of 21
Displaytech Ltd.
Website: www.displaytech.com.hk
Displaytech Ltd
LCD MODULE
64128K SERIES
Version : 1.2
P 2 of 21
PRODUCT SPECIFICATIONS
GENERAL SPECIFICATION ABSOLUTE MAXIMUM RATINGS ELECTRICAL CHARACTERISTICS ELECTRO-OPTICAL CHARACTERISTICS BLOCK DIAGRAM MECHANICAL DRAWING BACKLIGHT DRAWING BACKLIGHT SPECIFICATION QUALITY GUARANTEE PRECAUTIONS FOR USING LCD MODULES USING LCD MODULES REVISION RECORD
Contents in this document are subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Displaytech Ltd.
10 June 2008.
Displaytech Ltd
Item Display Format Dot Size (W x H) View Area (W x H) Module Size (W x H x T) LCD Type Polarizer Mode View Angle Backlight Backlight Driver Type Backlight Color Controller & LCD Driver Driving Method
LCD MODULE
64128K SERIES
Version : 1.2
P 3 of 21
GENERAL SPECIFICATION
Contents 128 x 64 DOTS 0.33mm x 0.33mm 50.00mm x 25.00mm 58.20mm x 41.70mm x 8.50mm FSTN Transflective 6 oclock / 12 oclock LED External Power White ST7565R-G 1/65 Duty, 1/9 Bias
mA
Displaytech Ltd
NO 1 Item Recommended Operating Voltage Symbol VLCD
LCD MODULE
64128K SERIES
Version : 1.2
P 4 of 21
ELECTRO-OPTICAL CHARACTERISTICS
Measuring Condition =0 = 0 =0 = 0 =0 = 0 =0 = 10 =0 = 10 =0 =180 =90 =270 Hz=64 C 25 0 25 40 0 25 40 0 25 40 0 25 40 25 25 25 25 25 STD.Value Min Typ ---------------------------10 30 30 ----9.0 --9.0 ----------218 ----115 --10 10 ----82 Max ----------------268 ----165 --40 --------Note1 Note2 Unit Remark
ms
Note4
Deg
Note1
5 NOTE 1:
uA
Note3
Detector
3H =90
9H =270 NOTE 2: 6H =0
Vth: The voltage Vop which the transmission rate of segment is 90%(positive) or 10%(negative) of saturated value on conditions of the selected waveform. (non-selected waveform is opposition) Vsat: The voltage Vop which the transmission rate of segment is 10%(positive) or 10%(negative) of saturated value on conditions of the selected waveform. (non-selected waveform is opposition)
Displaytech Ltd
NOTE 3:
LCD MODULE
64128K SERIES
Version : 1.2
P 5 of 21
NOTE 5:
CONTRAST RATIO (CR) 5.1 POSITIVE TYPE: CONTRAST RATIO = 5.2 NEGATIVE TYPE: CONTRAST RATIO = BRIGHTNESS AT VOP (SELECTED) BRIGHTNESS AT VOP (NON-SELECTED) BRIGHTNESS AT VOP (NON-SELECTED) BRIGHTNESS AT VOP (SELECTED)
NOTE 6:
CAPACITANCE (C)
Displaytech Ltd
BLOCK DIAGRAM
LCD MODULE
64128K SERIES
Version : 1.2
P 6 of 21
Displaytech Ltd
LCD MODULE
64128K SERIES
Version : 1.2
P 7 of 21
MECHANCIAL DRAWING
Displaytech Ltd
LCD MODULE
64128K SERIES
Version : 1.2
P 8 of 21
Displaytech Ltd
LCD MODULE
64128K SERIES
Version : 1.2
P 9 of 21
Displaytech Ltd
LCD MODULE
64128K SERIES
Version : 1.2 P 10 of 21
BACKLIGHT DRAWING
Displaytech Ltd
LCD MODULE
64128K SERIES
Version : 1.2 P 11 of 21
BACKLIGHT SPECIFICATION
N MECHANICAL SPECIFICATIONS
ITEM OUTLINE SIZE (LxWxH) VIEWING AREA (LxW) CONTACT PIN PITCH/LENGTH NO.OF LED SMT NOMINAL DIMENSIONS 58.20 x 41.70 x 8.50 52.0 x 27.0 NIL 3 UNIT mm mm mm ---
TESTING POINT
CIRCUIT DIAGRAM
REMARK: 1. AVERAGE LUMINOUS INTENSITY IS THE AVERAGE VALUE OF THE NINE INDICATED POINTS AS SHOWN. 2. MEASUREMENT INSTRUMENT: BM-7, APERTURE: 10mm.
Displaytech Ltd
N PURPOSE:
LCD MODULE
64128K SERIES
Version : 1.2 P 12 of 21
QUALITY GUARANTEE
It is to define the inspection standard of LCD modules
N PRODUCT STANDARD
1) INSPECTION AND TEST FUNCTION TEST APPEARANCE INSPECTION PACKING SPECIFICTION 2) INSPECTION CONDITION Put under the lamp (20w2) at a distance 100mm from the LCD Modules. Tilt upright 45 degree by the front (back) to inspect LCD appearance. 3) AQL INSPECTION LEVEL SAMPLING METHOD SAMPLING PLAN MAJOR DEFECT MINOR DEFECT GENERAL LEVEL
P M A L
R O T A R E P O
M C L
Displaytech Ltd
N INSPECTION STANDARD
LCD MODULE
64128K SERIES
Version : 1.2 P 13 of 21
1) FUNCTIONAL TEST STANDARD Inspection Standard Description Item 1 LCD has no display 2 LCM display do not change 3 Display wrong pattern
Reject
MAJ
Dim segment
Dim segment
Reject
MAJ
6 7 8
Wrong LCD viewing direction Dim Display LCD color variation Pattern parallelism L 20mm 30mm 40mm 50mm 60mm 70mm 80mm 90mm 100mm Acceptable range <a b 0.15mm | 0.43 | 0.2mm | 0.38 | 0.3mm | 0.43 | 0.35mm | 0.40 | 0.45mm | 0.43 | 0.50mm | 0.41 | 0.60mm | 0.43 | 0.65mm | 0.41 | 0.75mm | 0.43 | Standard =
Accept
x+ y 2
10
0.25 >0.25
1 W 4 1 > W 4
<
Reject
MIN
Displaytech Ltd
Item
LCD MODULE
64128K SERIES
Standard y
Version : 1.2 P 14 of 21
Standard Defect type
QTY 1 1 1 2 QTY Accept Accept Accept Reject Reject Accept Accept Reject Reject Reject Reject Reject Reject Reject Accept Accept MIN MIN
1 b 4
1 a 4
11
(X or y) 0.2mm
1 1 b a 4 4 1 1 b a 5 5 x+ y = 2
<0.10 0.1<0.20 0.20<0.25 0.25< 0.4 >0.4 Black line/white line(Lw)mm (L1.0)(W0.025) (1.0<L1.5)(W0.025) (L>1.5)(W0.025) (L>2)(W>0.025)
12
13
2 1 0 0 QTY 2 1 0 0
MIN MAJ
14 15 16
Backlight not function LED not function or dim Backlight defect (dirt, scratch)
2) COSMETIC INSPECTION STANDARD Item Standard description of inspection 1 LCD inspection item 1.1 LCD color variation 1.2 LCD broken 1.3 Wrong polarizer of LCD 1.4 Spot on LCD surface Scratch on LCD
Standard Defect type See sample Reject Reject Reject MIN MAJ MAJ MAJ
x
1.5
x+ y 2
Accept Accept Accept Reject Accept Accept Accept Reject Accept Accept Accept Reject Reject MIN MIN
scratch =W W0.015 W0.02 W0.03 W0.03 <0.1 0.1<0.2 0.20.25 >0.25 Bevy point
x+ y = 2
2 1 1 -
MIN MIN
Displaytech Ltd
Item Black line in LCD 1.8
LCD MODULE
64128K SERIES
Version : 1.2 P 15 of 21
Standard Defect type
(W) W0.025 W0.025 W>0.025 Size <0.15 0.150.25 >0.25 (W) W<0.02 W<0.03 W0.3
MIN
MIN
1.10 Line defect 1.11 Finger print 2 PCB/COB specification PCB deformity 2.1
MIN MIN
2.2 Deformity at PCB edge, damage circuit. Convex at PCB edge 2.3
Accept Reject Reject Reject Reject Accept Reject Reject Reject Reject See sample Reject Reject Reject Accept Reject Reject Accept Reject Accept
Damage excess 2x2mm at the PCB corner Scratch on PCB surface Scratch on PCB coat/leakage coat on PCB surface Open circuit PCB PTH open QTY2PCS QTY3PCS 30mm2 30mm2 a1/2w or b<w
MIN MIN MIN MIN MIN MAJ MAJ MAJ MAJ MIN MIN
2.9 Repair PCB PTH 2.10 Color different from one side to another side. 2.11 Repaired solder mask area Scratch circuit, damage Circuit 2.12
a>1/2w or b>w 3 3.1 3.2 3.3 3.4 Bezel specification Wrong Materials Incorrect dimension Bezel broken Rust on Bezel Size 0.3 0.3<0.5 >0.5 0.5 0.5<0.8 >0.8 cm2/per 2 1 0 2 1 0
Reject
MAJ MAJ MAJ MAJ Accept Accept Reject Accept Accept Reject
3.5
Top surface
MIN
Side
MIN
Displaytech Ltd
Item 3.6 Bezel bow or twist
LCD MODULE
64128K SERIES
h0.01 mm/mm h>0.01 mm/mm
Version : 1.2 P 16 of 21
Standard Defect type Accept Reject MIN
d1-d2tolerance 3.7
Accept
Face
d1-d2>tolerance Accept QTY W Not defined W0.15 W0.20 W0.3 W>0.3 2 2 Accept QTY W W0.2 W0.25 W0.3 except 2 2
Reject
MIN
See Sample
side L L3 L2
See Sample
=45+5
Accept
3.10 Void gap between bezel and PCB Bezel clip incorrectly 3.11
NG
Reject
MIN
Reject
MIN
4 Solder specification 4.1 Wrong component 4.2 Broken component Mis-alignment Component legs extend beyond the pad and Legs >pad distance(w) on solder area >W2 Component legs extend beyond the pad and Legs >pad distance(w) on solder area <W2 4.3 Component Offset Solder legs offset distance L<solder legs 1/4W Solder legs offset L>1/4W Component assembly defect 4.4
MAJ MAJ
Reject
MIN
Reject
MIN
Accept Reject
MIN
Displaytech Ltd
Item 4.7 Components hoist 4.8 Switch (socket) hoist
LCD MODULE
64128K SERIES
Version : 1.2 P 17 of 21
Standard Defect type Accept Reject MIN Accept Reject MIN Reject MAJ
4.9 Components cold solder or incomplete solder Solder PAD tilt up, but height (h) less than Solder PAD thickness (a) 4.10
Accept
Insufficient solder below components height or less than diameter 4.12 Reject MIN
4.13 Solder area less than soldering PAD Area by 2/3 Trimmed pin length beyond 0.09inch (2.3mm) 4.14
Reject
MIN
Reject
Min
Packing specification Wrong carton mark . Carton mark problem Carton damage extend than 150mm Carton damage, scratch more 50mm, less 150mm.
Displaytech Ltd
LCD MODULE
64128K SERIES
Version : 1.2 P 18 of 21
7.
N OPERATING PRECAUTIONS:
1. 2. 3. 4. DO NOT plug or unplug the module when the system is powered up. Minimize the cable length between the module and host MPU. For models with EL backlights, do not disable the backlight by interrupting the HV line. Unload inverters produce voltage extremes that may arc within a cable or at the display. Operate the module within the limits of the modules temperature specifications.
N MECHANICAL/ENVIRONMENTAL PRECAUTIONS:
1. 2. 3. 4. 5. 6. 7. Improper soldering is the major cause of module difficulty. Use of flux cleaner is not recommended as they may seep under the elastomeric connection and cause display failure. Mount the module so that it is free from torque and mechanical stress. Surface of the LCD panel should not be touched or scratched. The display front surface is an easily scratched, plastic polarizer. Avoid contact and clean only when necessary with soft, absorbent cotton dampened with petroleum benzene. Always employ anti-static procedure while handling the module. Prevent moisture build-up upon the module and observe the environmental constraints for storage temperature and humidity. Do not store in direct sunlight If leakage of the liquid crystal material should occur, avoid contact with this material, particularly ingestion. If the body or clothing becomes contaminated by the liquid crystal material, wash thoroughly with water and soap
Displaytech Ltd
N Storage Precautions
LCD MODULE
64128K SERIES
Version : 1.2 P 19 of 21
When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. Keep the modules in bags (avoid high temperature / high humidity and low temperatures below 0C). Whenever possible, the LCD modules should be stored in the same conditions in which they were shipped from our company.
N Others
Liquid crystals solidify under low temperature (below the storage temperature range) leading to defective orientation or the generation of air bubbles (black or white). Air bubbles may also be generated if the module is subject to a low temperature. If the LCD modules have been operating for a long time showing the same display patterns, the display patterns may remain on the screen as ghost images and a slight contrast irregularity may also appear. A normal operating status can be regained by suspending use for some time. It should be noted that this phenomenon does not adversely affect performance reliability. To minimize the performance degradation of the LCD modules resulting from destruction caused by static electricity etc., exercise care to avoid holding the following sections when handling the modules. Exposed area of the printed circuit board. Terminal electrode sections.
2.
When assembling the LCM into other equipment, the spacer to the bit between the LCM and the fitting plate should have enough height to avoid causing stress to the module surface, refer to the individual specifications for measurements. The measurement tolerance should be 0.1mm.
Displaytech Ltd
LCD MODULE
64128K SERIES
Version : 1.2 P 20 of 21
Displaytech Ltd
N Storage
1. 2. 3. 4.
LCD MODULE
64128K SERIES
Version : 1.2 P 21 of 21
When storing LCDs as spares for some years, the following precaution are necessary. Store them in a sealed polyethylene bag. If properly sealed, there is no need for desiccant. Store them in a dark place. Do not expose to sunlight or fluorescent light, keep the temperature between 0C and 35C. The polarizer surface should not come in contact with any other objects. (We advise you to store them in the container in which they were shipped.) Environmental conditions : Do not leave them for more than 168hrs. at 60C. Should not be left for more than 48hrs. at -20C.
N Safety
1. 2. It is recommended to crush damaged or unnecessary LCDs into pieces and wash them off with solvents such as acetone and ethanol, which should later be burned. If any liquid leaks out of a damaged glass cell and comes in contact with the hands, wash off thoroughly with soap and water.
N Limited Warranty
Unless agreed between DISPLAYTECH and customer, DISPLAYTECH will replace or repair any of its LCD modules which are found to be functionally defective when inspected in accordance with DISPLAYTECH LCD acceptance standards (copies available upon request) for a period of one year from date of shipments. Cosmetic/visual defects must be returned to DISPLAYTECH within 90 days of shipment. Confirmation of such date shall be based on freight documents. The warranty liability of DISPLAYTECH limited to repair and/or replacement on the terms set forth above. DISPLAYTECH will not be responsible for any subsequent or consequential events.
REVISION RECORD
VERSION 1.0 1.1 1.2 CHANGES Initial revision Corrected dimensional mistake on mechanical drawing on P.7 Power Supply for Logic and LCD inside ABSOLUTE MAXIMUN RATINGS was corrected DATE 7 March 2008 17 April 2008 10 June 2008