Professional Documents
Culture Documents
570 950mpa High Tensile Strength Steel
570 950mpa High Tensile Strength Steel
570 950mpa High Tensile Strength Steel
Flux Cored Arc Welding Wires Covered Arc Welding Electrodes Submerged Arc Welding Materials Gas Metal Arc Welding Wires
59
NITTETSU SF-60
APPLICATIONS
CHARACTERISTICS
NITTETSU SF-60 is a rutile type seamless flux cored arc welding wire to be used with CO2 shield gas and was designed with emphasis on crack resistance in the welding of thick plates. The diffusible hydrogen content is as low as that of solid wires and crack resistance is excellent even in the low heat input welding of thick plates.
n TYPICAL MECHANICAL PROPERTIES OF WELD METAL Yield Point, MPa 580 Tensile Strength, MPa 615 Elongation, % 27 Charpy 2V-notch at 5C, J 110
n TYPICAL WELD JOINT TEST Joint Tensile Test Tensile Strength, Location of MPa Fracture 600 Weld metal Charpy 2V-notch at 0C, J 110 Base metal SM570Q Plate Thickness mm 20 Welding Method Flat, V groove, 8 passes
n SIZES & RECOMMENDED CURRENT RANGE<DC( )> Diameter (mm) Current A F, H H-Fil V 1.2 180~300 180~300 180~250
60
Approval: NK
Memo
61
NITTETSU L-60
For 590MPa High Tensile Strength Steel
APPLICATIONS
Welding of SM570, SPV450 and 590MPa high tensile strength steel (WEL-TEN 590) for penstocks, storage tanks, pressure vessels, bridges, offshore structures and machinery.
CHARACTERISTICS
NITTETSU L-60 is an extra low hydrogen type electrode with high resistance to moisture absorption. Weldability in all positions, mechanical properties and X-ray quality are excellent. Weld metal shows satisfactory crack resistance due to its extremely low diffusible hydrogen content.
n TYPICAL CHEMICAL COMPOSITION OF WELD METAL ( % ) C 0.07 Si 0.42 Mn 1.12 Ni 0.73 Mo 0.22
n TYPICAL MECHANICAL PROPERTIES OF WELD METAL Yield Point, MPa 540 Tensile Strength, MPa 640 Elongation, % 29 Charpy 2V-notch at 10C, J 180
n SIZES & RECOMMENDED CURRENT RANGE<AC or DC( )> Diameter (mm) Length (mm) F Current A V, OH 3.2 350 70~140 60~130 4.0 400 120~190 90~170 5.0 400 190~250 140~190 6.0 450 250~310
62
NITTETSU L-62CF
For 590MPa High Tensile Strength Steel
APPLICATIONS
Welding of SPV490 and 590MPa high tensile strength steel (WEL-TEN 610) for penstocks, storage tanks, pressure vessels, bridges, offshore structures and machinery.
CHARACTERISTICS
NITTETSU L-62CF is an extra low hydrogen type electrode for all position welding of 590MPa high tensile strength steel. It is suitable for site welding of storage tanks since its coating flux is highly resistant to moisture absorption even in an atmosphere of high temperature humidity. Extremely low diffusible hydrogen content in weld metal assures excellent crack resistance.
n TYPICAL CHEMICAL COMPOSITION OF WELD METAL ( % ) C 0.07 Si 0.45 Mn 1.36 Ni 0.70 Mo 0.35
n TYPICAL MECHANICAL PROPERTIES OF WELD METAL Yield Point, MPa 590 Tensile Strength, MPa 660 Elongation, % 30 Charpy 2V-notch at 20C, J 170
n SIZES & RECOMMENDED CURRENT RANGE<AC or DC( )> Diameter (mm) Length (mm) F Current A V, OH 3.2 350 100~140 90~130 4.0 400 140~190 120~170 5.0 400 190~250 140~190 6.0 450 250~310
63
NITTETSU L-60LT
For 590MPa High Tensile Strength Steel
APPLICATIONS
Welding of 590MPa high tensile strength steel (N-TUF490) for low temperature service for structures to be used in frigid area, pressure vessels, storage tanks and offshore structures.
CHARACTERISTICS
NITTETSU L-60LT is an extra low hydrogen type electrode for all positions with high resistance to moisture absorption. Weld metal shows excellent toughness at temperatures around 50C and CTOD (crack tip opening displacement) value.
n TYPICAL MECHANICAL PROPERTIES OF WELD METAL Yield Point, MPa 600 Tensile Strength, MPa 680 Elongation, % 28 Charpy 2V-notch at 50C, J 180
n TYPICAL CTOD VALUES OF WELD JOINT (AS WELDED) Base Metal (Thickness) A537C1.2 Mod (25mm) Groove Y Welding Conditions Diameter: 4.0mm Position:V-up Heat Input: 32kJ/cm CTOD Value, (mm) 10C 1.17 1.11 1.26
n SIZES & RECOMMENDED CURRENT RANGE<AC or DC( )> Diameter (mm) 3.2 4.0 5.0 Length (mm) 350 400 400 F 100~140 140~190 190~250 Current A V, OH 90~130 120~170 140~190
64
NITTETSU L-80
For 780MPa High Tensile Strength Steel
APPLICATIONS
Welding of 780MPa high tensile strength steel (WEL-TEN 780, 780C, 780P and 780E) for penstocks, pressure vessels, bridges, machinery and turbine casings.
CHARACTERISTICS
NITTETSU L-80 is an extra low hydrogen type electrode with high resistance to moisture absorption. Weldability in all positions, mechanical properties and X-ray quality are excellent. Extremely low diffusible hydrogen content in weld metal assures satisfactory crack resistance.
n TYPICAL CHEMICAL COMPOSITION OF WELD METAL ( % ) C 0.05 Si 0.44 Mn 1.35 Ni 2.52 Cr 0.18 Mo 0.54
n TYPICAL MECHANICAL PROPERTIES OF WELD METAL 0.2% Proof Stress, MPa 740 Tensile Strength, MPa 830 Elongation, % 24 Charpy 2V-notch at 20C, J 96
n SIZES & RECOMMENDED CURRENT RANGE<AC or DC( )> Diameter (mm) Length (mm) F Current A V, OH 3.2 350 100~140 90~130 4.0 400 140~190 120~170 5.0 400 190~250 140~190 6.0 400 250~310
65
NITTETSU L-80SN
For 780MPa High Tensile Strength Steel
APPLICATIONS
Welding of 780MPa high tensile strength steel (WEL-TEN 780) for offshore structures, pressure vessels, storage tanks and structures to be used in frigid area.
CHARACTERISTICS
NITTETSU L-80SN is a ultra low hydrogen type electrode with high resistance to moisture absorption. Weld metal shows excellent toughness at around 80C. It can be used with confidence for welding extremely thick plates such as racks of offshore structures since extremely low diffusible hydrogen content in weld metal assures satisfactory crack resistance.
n TYPICAL MECHANICAL PROPERTIES OF WELD METAL 0.2% Proof Stress, MPa 760 Tensile Strength, MPa 860 Elongation, % 22 Charpy 2V-notch at 80C, J 90
n SIZES & RECOMMENDED CURRENT RANGE<AC or DC( )> Diameter (mm) Length (mm) F Current A V, OH 3.2 350 100~140 90~130 4.0 400 140~190 120~170 5.0 400 190~250 140~190 6.0 400 250~310
66
Memo
67
Covered Arc Welding Electrodes for 590~980MPa High Tensile Strength Steel
Brand Name ldentification Color End Secondary Specification JIS AWS Dia. mm Application and Characteristics
NITTETSU L-60S
Orange
Light blue
A5.5 E8016 -G
1 2
NITTETSU L-60W Pink Brown Z 3211 E5916N1M1 A5.5 E8016 -G
Extra low hydrogen type electrode with high resistance to moisture absorption. It assures satisfactory toughness at -45C, weldability in all positions and X-ray quality. Crack resistance is excellent due to the extremely low diffusible hydrogen content in weld metal. Low hydrogen type electrode suitable for uranami (sound penetration bead) welding of 590MPa in all positions. Extremely low diffusible hydrogen content in weld metal assures excellent crack resistance. Extra low hydrogen type electrode with high resistance to moisture absorption. Weldability in all positions, mechanical properties and X-ray quality are excellent. Extremely low diffusible hydrogen content in weld metal assures satisfactory crack resistance. Extra low hydrogen type electrode with high resistance to moisture absorption and suitable for all position welding of 685MPa. Weldability and X-ray properties are excellent and extremely low diffusible hydrogen content of weld metal assures excellent crack resistance and mechanical properties. Ultra low hydrogen type electrode with high resistance to moisture absorption. It is suitable for welding under severe conditions such as site welding of penstocks and tanks since extremely low diffusible hydrogen content in weld metal assures excellent crack resistance.
NITTETSU L-62
Pink
White
NITTETSU L-70
Orange
Green
Z 3211 E6916N4M3U
A5.5 E10016 -G
NITTETSU L-80EL
Red
Pink
A5.5 E11016 -G
68
Typical Mechanical Properties of Weld Metal Tensile Strength, MPa Elongation, % Charpy 2V-notch, J
0.05
0.46
1.12
1.51
0.20
580
650
29
45C 120
1 2
0.07 0.60 1.02 0.51 0.19 550 630 31 10C 92
0.07
0.48
1.39
0.76
0.35
600
670
31
20C 170
0.05
0.41
1.16
2.10
0.48
660
750
26
20C 170
0.06
0.45
1.44
2.44
0.20
0.42
740
820
24
20C 120
1.4
69
Covered Arc Welding Electrodes for 590~980MPa High Tensile Strength Steel
Brand Name ldentification Color End Secondary Specification JIS AWS Dia. mm Application and Characteristics
NITTETSU L-100EL
Orange
Orange
1 2
Ultra low hydrogen type electrode with high resistance to moisture absorption and suitable for all position welding of 950MPa high tensile strength steel. Weldability and X-ray properties are excellent and extremely low diffusible hydrogen content of weld metal assures excellent crack resistance and mechanical properties.
70
Typical Mechanical Properties of Weld Metal Tensile Strength, MPa Elongation, % Charpy 2V-notch, J
0.06
0.25
1.67
2.01
0.89
0.75
910
990
21
25C 70
1.7
1 2
71
Single and multi-layer welding of 590MPa high tensile strength steel for ships, steel frames, bridges and pressure vessels.
CHARACTERISTICS
Weld metal shows excellent impact values and sufficient strength and toughness as welded and after stress relieving annealing.
n TYPICAL CHEMICAL COMPOSITION OF WELD METAL (%) Plate Base C Si Mn P S Mo Thickness Metal mm 25 0.09 0.38 1.33 0.014 0.011 0.49 WT590 n TYPICAL MECHANICAL PROPERTIES OF WELD METAL Tensile Test Yield Point, Tensile Strength, MPa MPa 540 630 Elongation, % 25 Charpy 2 V-notch, J 40C 41 0C 69 Plate Base Thickness Metal mm WT590 25
Welding Method
Multi-layer
Groove Geometry
30 25 13
Pass
Note
25
4.0
1~14
Multi-layer
72
Fillet welding of 590MPa high tensile strength steel for steel frames, bridges, pressure vessels and storage tanks.
CHARACTERISTICS
Bead appearance and slag removal are excellent in flat and horizontal fillet welding with single or double electrodes. NITTETSU NF-820 is a pumiceous flux and is economical due to its low consumption rate.
n TYPICAL CHEMICAL COMPOSITION OF WELD METAL (%) Plate Base C Si Mn P S Mo Thickness Metal mm 25 0.04 0.75 1.77 0.017 0.009 0.47 WT590 n TYPICAL MECHANICAL PROPERTIES OF WELD METAL Tensile Test Yield Point, Tensile Strength, MPa MPa 530 610 Elongation, % 26 Charpy 2 V-notch, J 20C 31 0C 48 Plate Base Thickness Metal mm WT590 25
Welding Method
Multi-layer
Groove Geometry
30 25 13
Pass
Note
25
4.0
1~14
Multi-layer
73
F9P8-EG-G
Flat butt welding of 590MPa high tensile strength steel for low temperature service for offshore structures and structures to be used in frigid areas.
CHARACTERISTICS
NITTETSU NB-250H is a high basic type bonded flux and assures excellent low temperature toughness (impact and CTOD properties) both as welded and after stress relieving annealing. Slag is easy to remove even in narrow grooves.
n TYPICAL CHEMICAL COMPOSITION OF WELD METAL (%) Plate Base Thickness C Si Mn P S Ni Mo Metal mm 0.10 0.20 1.71 0.001 0.003 0.74 0.29 HT590 50 n TYPICAL MECHANICAL PROPERTIES OF WELD METAL Charpy 2 V-notch, CTOD Tensile Test J mm Yield Point, MPa 610 590 n TYPICAL Plate Thickness mm 50
Plate Base Welding ElonPWHT Thickness Tensile Metal Method gation, Strength, 60C 40C 10C mm MPa % X groove, as 710 29 150 170 2.06 HT590 50 multi-layer welded X groove, 680 30 110 140 2.99 605C HT590 50 multi-layer 2.5h GROOVE GEOMETRY AND WELDING CONDITIONS Wire Groove Current, Voltage, Speed, Dia. Pass Note Geometry A V cm/min mm 1~7 1 600 28 30 50 Multi-layer 25 2~7 650 30 28 50 5 4.8 with 8 600 28 30 20 gouging 60 8~15 9~15 650 30 28
74
Horizontal butt welding of 590MPa high tensile strength steel for storage tanks.
CHARACTERISTICS
Bead appearance and slag removal are excellent and pock marks rarely occur. Weld metal shows satisfactory toughness and X-ray quality.
n TYPICAL CHEMICAL COMPOSITION OF WELD METAL (%) Base C Si Mn P S Metal 0.09 0.29 1.63 0.023 0.005 HW490 n TYPICAL MECHANICAL PROPERTIES OF WELD METAL Charpy 2 V-notch, Joint Tensile Test J Tensile Location of Strength, 46C 20C 0C Fracture MPa 640 Base Metal 60 110 150
Plate Thickness mm 25
Plate Thickness mm 25
n TYPICAL GROOVE GEOMETRY AND WELDING CONDITIONS Plate Wire Groove Current, Voltage, Speed, Thickness Dia. Pass Geometry A V cm/min mm mm 1 460 26 40 1st 2 480 28 50 25 3 480 27 50 45 3.2 25 1 500 28 35 45 2 2nd 2 480 28 60 3 470 27 60
Heat Note Input 17.9 16.1 15.5 24.0 13.4 12.7 No gouging on second side
75
Multi-layer butt welding of aluminium-killed steel for low temperature service for offshore structures, installations for low temperatures service and structures to be used in frigid areas.
CHARACTERISTICS
NITTETSU NB-60L is a Ti-B type bonded flux and assures excellent low temperature toughness and CTOD both as welded and after stress relief annealing.
n TYPICAL CHEMICAL COMPOSITION OF WELD METAL ( % ) Plate Base Welding C Si Mn P S Mo Thickness Metal Method mm 0.08 0.18 1.54 0.010 0.005 0.18 YP420 25 X groove, multi-layer n TYPICAL MECHANICAL PROPERTIES OF WELD METAL
Tensile Test
Elongation, % 32 30
Charpy 2 V-notch, J
Base Metal
Plate Thickness mm 25
YP420
n TYPICAL GROOVE GEOMETRY AND WELDING CONDITIONS Plate Thickness mm 75 25 Wire Dia. mm 4.8 4.8 Groove Geometry
50 75 70 25 20 16 38 5 32
Voltage, Speed, Pass Current, A V cm/min 1 2~13 14 15~29 1~11 600 700 600 700 700 27 32 28 32 30 30 30 30 30 30
76
Welding of 780MPa high tensile strength steel for offshore structures, pressure vessels, penstocks and bridges.
CHARACTERISTICS
NITTETSU NB-250H is a bonded flux designed to minimize the diffusible hydrogen content in weld metal and, therefore, crack resistance is extremely high. Impact properties are excellent at low temperature and slag is easy to remove even in narrow grooves.
n TYPICAL CHEMICAL COMPOSITION OF WELD METAL (%) C Si Mn Ni Cr Mo Base Metal WT780 Plate Thickness Welding Method mm 25 Multi-layer
n TYPICAL MECHANICAL PROPERTIES OF WELD METAL Plate Heat Base Thickness Input Elong0.2% Tensile Metal mm kJ/cm Proof Stress, Strength, ation, 60C 40C MPa MPa % 730 830 29 86 120 WT780 25 31 Joint Tensile Test Charpy 2 V-notch, J Welding Method Multi-layer
n TYPICAL GROOVE GEOMETRY AND WELDING CONDITIONS Plate Thickness mm 25 Wire Dia. mm 4.0 Groove Geometry
20 25 16
Pass 1~9
Note Multi-layer
77
Welding of 780MPa high tensile strength steel for offshore structures, pressure vessels, penstocks and bridges. Welding of 3Ni-1.75%Cr-0.5%Mo steel such as ASTM A508 Gr.4N and A543 type B Cl.1 steel.
CHARACTERISTICS
NITTETSU NB-80 is a bonded flux designed to minimize the diffusible hydrogen content in weld metal and, therefore, crack resistance is extremely high. Impact properties are excellent at low temperature and slag is easy to remove even in narrow grooves.
Pass 1~9
Note Multi-layer
78
Memo
79
Submerged Arc Welding Materials for 590~780MPa High Tensile Strength Steel
Specification Brand Name Application and Characteristics JIS AWS C Si Mn P S Typical Chemical of Weld
1 2
Welding of 570MPa high strength steel for structures, bridges, pressure vessels and penstocks, etc.
0.09
0.37
1.38
0.015
0.010
Welding of 610MPa high strength steel for structures, bridges, pressure vessels and penstocks, etc.
0.09
0.37
1.61
0.018
0.010
Narrow gap welding of 590MPa low temperature service steel for nuclear reactor pressure vessels and structures to be used in 0.07 frigid areas. Slag is extremely easy to remove and weld metal shows excellent impact value. Butt and fillet welding of 690MPa high tensile strength steel. NITTETSU Y-70M is a Mn-NiCr-Mo type wire and NITTETSU 0.07 YF-15B has been designed to minimized diffusible hydrogen content in weld metal and, therefore, crack resistance is excellent. Butt welding of 690MPa high tensile strength steel. NITTETSU NB-250H is a high basic type flux and weld metal shows excellent low temperature toughness both 0.10 as welded and after stress relieving annealing. Slag is easy to remove even in narrow gap welding. Fillet welding of 780MPa high tensile strength steel for bridges. Diffusible hydrogen content is 0.06 extremely low and, therefore, weld metal shows excellent crack resistance.
0.14
1.60
0.010
0.004
A5.23 F10A4-EG-G
0.48
1.68
0.018
0.008
0.16
1.66
0.012
0.006
A5.23 F11A2-EGM3
0.36
1.30
0.015
0.007
80
Typical Mechanical Properties of Weld Metal ElonYield Point, Tensile Strength, gation, MPa MPa % 550 630 620 660 630 27 30 25 27 Charpy 2 V-notch, C 0 0 0 0 J 110 93 89 83 PWHT
1 2
0.42 560
0.94 0.38
660
28
50
91
640
29
50
64
625C 1h
52 56 76 82 WT690 53
X groove, multi-layer
79 72 WT780 22 Multi-layer
81
NITTETSU YM-60C
For 590MPa High Tensile Strength Steel
APPLICATIONS
Welding of 590MPa high tensile strength steel for steel frames, bridges, pressure vessels and penstocks.
CHARACTERISTICS
NITTETSU YM-60C is a gas metal arc welding wire to be used with CO2 shield gas. Arc is stable, spatters are few and weldability is excellent even in high welding current range. High efficiency is obtained in automatic and semiautomatic welding due to high deposition rate and deep penetration. It is also applicable to OSCON process, our manpower saving automatic welding process.
n TYPICAL CHEMICAL COMPOSITION OF WELD METAL ( % ) Shield Gas CO2 C 0.07 Si 0.38 Mn 1.38 P 0.005 S 0.012 Mo 0.35
n TYPICAL MECHANICAL PROPERTIES OF WELD METAL Yield Point, MPa 590 Tensile Strength, MPa 660
Charpy 2V-notch, J 5C 80
Elongation, % 30
25
320
35
30
n SIZES & RECOMMENDED CURRENT RANGE<DC( )> Diameter Current Approval: NK, NV (mm) (A) 1.2 80~350 1.6 250~550
82
NITTETSU YM-60A
For 590MPa High Tensile Strength Steel
APPLICATIONS
Welding of 590MPa high tensile strength steel for steel frames, bridges, pressure vessels, storage tanks and penstocks.
CHARACTERISTICS
NITTETSU YM-60A is a gas metal arc welding wire to be used with Ar+5~25%CO2 or Ar+2~5%O2 shield gas. It is suitable for spray arc welding with high current and vertical butt welding with low current and high heat input. Weld metal shows excellent mechanical properties and crack resistance. Weldability is satisfactory and bead appearance is beautiful when it is used for OSCON Process, our manpower saving automatic welding process.
n TYPICAL CHEMICAL COMPOSITION OF WELD METAL ( % ) Shield Gas Ar+20%CO2 C 0.06 Si 0.35 Mn 1.45 P 0.008 S 0.003 Mo 0.38
Elongation, % 30
25
330 200
27 20
25 4.5
As welded
n SIZES & RECOMMENDED CURRENT RANGE<DC( )> Diameter Current (mm) (A) 1.2 80~350 1.6 200~450
83
NITTETSU YM-80C
For 780MPa High Tensile Strength Steel
APPLICATIONS
Welding of 780MPa high tensile strength steel for steel frames, bridges, pressure vessels and penstocks.
CHARACTERISTICS
NITTETSU YM-80C is a gas metal arc welding wire to be used with CO2 shield gas. Arc is stable, spatters are few and weldability is satisfactory even in high welding current range. Bead appearance is beautiful and weld metal shows excellent toughness.
n TYPICAL MECHANICAL PROPERTIES OF WELD METAL 0.2% Proof Stress, MPa 720 Tensile Strength, MPa 850 Elongation, % 23 Charpy 2V-notch, J 20C 66 0C 84
Tensile Location Strength, of 15C MPa Fracture 830 840 Base metal Base metal 69 57
n SIZES & RECOMMENDED CURRENT RANGE<DC( )> Diameter Current (mm) (A) 0.9 50~200 1.0 70~250 1.2 80~350 1.6 250~550
84
NITTETSU YM-80A
For 780MPa High Tensile Strength Steel
APPLICATIONS
Welding of 780MPa high tensile strength steel for steel frames, bridges, pressure vessels, penstocks and offshore structures.
CHARACTERISTICS
NITTETSU YM-80A is a gas metal arc welding wire to be used with argon rich shield gas such as Ar+5~25%CO2 or Ar+2~5%O2. Arc is stable, spatters are few and weldability is excellent in a wide current range. Bead appearance is beautiful and weld metal shows excellent toughness at low temperatures.
n TYPICAL CHEMICAL COMPOSITION OF WELD METAL ( % ) Shield Gas Ar+20%CO2 C 0.08 Si 0.31 Mn 1.30 Ni 2.60 Cr 0.50 Mo 0.57
n TYPICAL MECHANICAL PROPERTIES OF WELD METAL 0.2% Proof Stress, MPa 760 Tensile Strength, MPa 870 Elongation, % 22 Charpy 2V-notch, J 60C 61 40C 72
40C
75
WEL-TEN 80
25
n SIZES & RECOMMENDED CURRENT RANGE<DC( )> Diameter Current (mm) (A) 1.0 70~250 1.2 80~350 1.6 200~450
85
Gas Metal Arc Welding Wires for 590~980MPa High Tensile Strength Steel
Specification Brand Name Shield Gas Dia. mm Application and Characteristics
JIS
AWS
NITTETSU YM-60CS
CO2
Z 3312 G59JA1UC3M1T
A5.28 ER90S-G
1 2
NITTETSU YM-60AS Ar + 20%CO2 Z 3312 G59JA1UM3M1T A5.28 ER90S-G
Welding of 590MPa high strength steel for steel frames, bridges, pressure vessels and penstocks.
Welding of 590MPa high strength steel for steel frames, bridges, pressure vessels and penstocks.
NITTETSU YM-70C
CO2
Z 3312 G69A2UCN4M3T
A5.28 ER100S-G
Welding of 690MPa high tensile strength steel. Good weldability with stable arc and few spatters and excellent toughness are assured even in high current welding. Welding of 690MPa high strength steel for civil construction equipment, steel frames, bridge and pressure vessels. Welding of 690MPa high tensile strength steel. Arc is stable, spatters are extremely few, and beautiful bead appearance and excellent toughness are obtained in a wide current range with Ar+20%CO 2 or Ar+O 2 mixture gas.
NITTETSU YM-70CS
Z 3312 G69A2UCN1M2T
A5.28 ER100S-G
NITTETSU YM-70A*
Z 3312 G69A3UMN4M3T
A5.28 ER100S-G
NITTETSU YM-80AS
Ar + 20%CO2
Z 3312 G78JA2UMN6CM3T
A5.28 ER110S-G
Welding of 780MPa high strength steel for steel frames, bridges, pressure vessels, penstocks and offshore structures.
86
Typical Mechanical Properties of Weld Metal 0.2% Proof Stress, MPa 560 Tensile Strength, MPa 680 630 630 610 Elon- Charpy 2V-notch gation, at 0C, % J 28 29 30 31 108 81 167 159 20C 98 0C 130 5C 89 40C 86 PWHT
Type of Current
0.09
DC (+)
1 2
DC (+)
0.05
0.30 530
0.30
610
720
25
DC (+)
0.08
0.34
650
740
24
DC (+)
0.07 0.33
0.44
655
740
25 20C 130
DC (+)
740 0.05 0.44 1.02 0.010 0.009 2.60 0.20 0.48 720
820 800
24 25
127 91
As welded 580C 1h
DC (+)
87
Gas Tungsten Arc Welding Wires 590~780MPa High Tensile Strength Steel
Brand Name Shield Gas Specification JIS AWS Dia. mm (Spool) 1.2 1.6 2.0 2.4 1000 (12.5, 20 kg) 1.2 1.6 2.0 2.4 1000 1.2 1.6 2.0 2.4 1000 Application and Characteristics
NITTETSU YT-60
Ar
A5.28 ER80S-G
1 2
NITTETSU YT-70S Ar A5.28 ER100S-G
Welding of 590MPa high tensile strength steel plates. It is also suitable for uranami (sound penetration bead) welding without back shielding.
NITTETSU YT-80S
Ar
A5.28 ER110S-G
88
Typical Chemical Composition of Weld Metal (%) C Si Mn Ni Mo Cr Yield Point, MPa 655 0.09 0.03 1.79 0.50 580
Typical Mechanical Properties of Weld Metal Tensile Strength, MPa 700 Elongation, % 27 Charpy 2V-notch, J 40C 120 40C 300
PWHT
As welded
630
31
625C1h
1 2
0.09
0.41
1.60
0.38
700
780
27
20C 98
As welded
0.06
0.43
1.10
2.80
0.45
0.21
760
840
28
20C 98
As welded
89
Memo
90