Professional Documents
Culture Documents
EDGE Technology Report
EDGE Technology Report
Introduction
The business of wireless data is expected to grow in the region of 100200 per cent per annum and the mobile communications industry agrees that wireless data services will form the foundation for future business. The enormous success of short messaging in many countries proves that people accept the benefits of non-voice services.
Wireless Application Protocol (WAP) as well as the higher transmission speeds of High Speed Circuit Switched Data (HSCSD), and the convenience of "always on-line" direct internet connections with General Packet Radio Service (GPRS) these standards enable greater sophistication as end-user services move towards personal multimedia. A new technology, Enhanced Data Rates for GSM Evolution (EDGE) was introduced to boost network capacity and data rates of both circuit switching (HSCSD) and packet switching (GPRS), to meet the demands of wireless multimedia applications and mass market deployment. With the introduction of EDGE in GSM phase 2+, existing services such as GPRS and high-speed circuit switched data (HSCSD) are enhanced by offering a new physical layer. The services themselves are not modified. EDGE is introduced within existing specifications and descriptions rather than by creating new ones. Many wireless data applications today can be implemented with 9.6kbit/s data. However, bandwidth-hungry fixed line data applications - web browsing, access to corporate data bases, and so on - would benefit from higher transmission speeds when used over the mobile network. HSCSD will significantly improve will performance, enable especially for time-critical access to applications. GPRS cost-effective wireless
applications that rely upon data bursts, adding packet switching to GSM with a packet-based air interface on top of the current circuit switched mode of operation.
EDGE GPRS will provide the connectivity needed in packet-switched data networks such as the Internet. General Packet Radio Services (GPRS) is a packet-based wireless communication service that promises data rates from 56 up to 114 Kbps and continuous connection to the Internet for mobile phone and computer users. The higher data rates will allow users to take part in video conferences and interact with multimedia Web sites and similar applications using mobile handheld devices as well as notebook computers. GPRS is based on Global System for Mobile (GSM) communication and will complement existing services such circuitswitched cellular phone connections and the Short Message Service (SMS). In theory, GPRS packet-based service should cost users less than circuitswitched services since communication channels are being used on a shared-use, as-packets-are-needed basis rather than dedicated only to one user at a time. It should also be easier to make applications available to mobile users because the faster data rate means that middleware currently needed to adapt applications to the slower speed of wireless systems will no longer be needed. As GPRS becomes available, mobile users of a virtual private network (VPN) will be able to access the private network continuously rather than through a dial-up connection. GPRS will also complement Bluetooth, a standard for replacing wired connections between devices with wireless radio connections. In addition to the Internet Protocol (IP), GPRS supports X.25, a packet-based protocol that is used mainly in Europe. GPRS is an evolutionary step toward Enhanced Data GSM Environment (EDGE). EDGE, a new radio interface technology with enhanced modulation, increases the HSCSD and GPRS data rates by up to three fold. EDGE modulation will increase the data throughput provided by the packet switched service even over 400kbit/s per carrier. Similarly, the data rates Model Engineering College,Thrikkakara 2
EDGE of circuit switched data can be increased, or existing data rates can be achieved using fewer timeslots, saving capacity. Accordingly, these higher speed data services are referred to as EGPRS (Enhanced GPRS) and ECSD (Enhanced Circuit Switched Data). GPRS allows data rates of 115 kbps and, theoretically, of up to 160 kbps on the physical layer. EGPRS is capable of offering data rates of 384 kbps and, theoretically, of up to 473.6 kbps. A new modulation technique and error-tolerant transmission methods, combined with improved link adaptation mechanisms, make these EGPRS rates possible. This is the key to increased spectrum efficiency and enhanced applications, such as wireless Internet access, email and file transfers. As a modification to existing GSM networks, EDGE does not require new network elements. EDGE is especially attractive to GSM 900, GSM 1800 and GSM 1900 operators that do not have a licence for UMTS, but still wish to offer competitive personal multimedia applications utilising the existing band allocation. Also, EDGE can co-exist with UMTS, for instance to provide high-speed services for wide-area coverage while UMTS is deployed in urban hot spots.
EDGE
EDGE
EDGE technology
EDGE leverages the knowledge gained through use of the existing GPRS standard to deliver significant technical improvements. Although GPRS and EDGE share the same symbol rate, the modulation bit rate differs. EDGE can transmit three times as many bits as GPRS during the same period of time. This is the main reason for the higher EDGE bit rates. The differences between the radio and user data rates are the result of whether or not the packet headers are taken into consideration. These different ways of calculating throughput often cause misunderstanding within the industry about actual throughput figures for GPRS and EGPRS. The data rate of 384 kbps is often used in relation to EDGE. The International Telecommunications Union (ITU) has defined 384 kbps as the data rate limit required for a service to fulfill the International Mobile
EDGE
To achieve higher bit rates per time slot than those available in GSM/GPRS, the modulation method requires change. EDGE is specified to reuse the channel structure, channel width, channel coding and the existing mechanisms and functionality of GPRS and HSCSD. The modulation standard selected for EDGE, 8-phase shift keying (8PSK), fulfills all of those requirements. 8PSK modulation has the same qualities in terms of generating interference on adjacent channels as GMSK. This makes it possible to integrate EDGE channels into an existing frequency
EDGE plan and to assign new EDGE channels in the same way as standard GSM channels. The 8PSK modulation method is a linear method in which three consecutive bits are mapped onto one symbol in the I/Q plane. The symbol rate, or the number of symbols sent within a certain period of time, remains the same as for GMSK, but each symbol now represents three bits instead of one. The total data rate is therefore increased by a factor of three. The distance between the different symbols is shorter using 8PSK modulation than when using GMSK. Shorter distances increase the risk for misinterpretation of the symbols because it is more difficult for the radio receiver to detect which symbol it has received. Under good radio conditions, this does not matter. Under poor radio conditions, however, it does. The extra bits will be used to add more errorcorrecting coding, and the correct information can be recovered. Only under very poor radio environments is GMSK more efficient. Therefore the EDGE coding schemes are a mixture of both GMSK and 8PSK.
Coding schemes
For GPRS, four different coding schemes, designated CS1 through CS4, are defined. Each has different amounts of error-correcting coding that is optimized for different radio environments. For EGPRS, nine modulation coding schemes, designated MCS1 through MCS9, are introduced. These fulfill the same task as the GPRS coding schemes. The lower four EGPRS coding schemes (MSC1 to MSC4) use GMSK, whereas the upper five (MSC5 to MSC9) use 8PSK modulation. Figure 4 shows both GPRS and EGPRS coding schemes, along with their maximum throughputs.
EDGE
GPRS user throughput reaches saturation at a maximum of 20 kbps with CS4, whereas the EGPRS bit rate continues to increase as the radio quality increases, until throughput reaches saturation at 59.2 kbps. Both GPRS CS1 to CS4 and EGPRS MCS1 to MCS4 use GMSK modulation with slightly different throughput performances. This is due to differences in the header size (and payload size) of the EGPRS packets. This makes it possible to resegment EGPRS packets. A packet sent with a higher coding scheme (less error correction) that is not properly received, can be retransmitted with a lower coding scheme (more error correction) if the new radio environment requires it. This resegmenting (retransmitting with another coding scheme) requires changes in the payload sizes of the radio blocks, which is why EGPRS and GPRS do not have the same performance for the GMSK modulated coding schemes. Resegmentation is not possible with GPRS.
EDGE
Packet handling
Another improvement that has been made to the EGPRS standard is the ability to retransmit a packet that has not been decoded properly with a more robust coding scheme. For GPRS, resegmentation is not possible. Once packets have been sent, they must be retransmitted using the original coding scheme even if the radio environment has changed. This has a significant impact on the throughput, as the algorithm decides the level of confidence with which the link adaptation (LA) must work. Below is an example of packet transfer and retransmission for GPRS. A. The GPRS terminal receives data from the network on the downlink. Due to a GPRS measurement report that was previously received, the link adaptation algorithm in the base station controller decides to send the next radio blocks (e.g., numbers 1 to 4) with CS3. During the transmission of these packages, the carrier-to-interference ratio (C/I) decreases dramatically, changing the radio environment. After the packets have been transmitted, the network polls for a new measurement report, including the acknowledged/unacknowledged bitmap that tells the network which radio blocks were received correctly. B. The GPRS handset replies with a packet downlink
acknowledged/unacknowledged message containing the information about the link quality and the bitmap. In this scenario, it is assumed that packets 2 and 3 were sent erroneously. C. Based on the new link quality information, the GPRS link adaptation algorithm will adapt the coding scheme to the new radio environment using CS1 for the new packets 5 and 6. However, because GPRS cannot resegment the old packets, packets 2 and 3 must be retransmitted using CS3, although there is a significant risk that these packets still may not be decoded correctly. As a result, the link adaptation for GPRS requires Model Engineering College,Thrikkakara 9
EDGE careful selection of the coding scheme in order to avoid retransmissions as much as possible. With EGPRS, resegmentation is possible. Packets sent with little error protection can be retransmitted with more error protection, if required by the new radio environment. The rapidly changing radio environment has a much smaller effect on the problem of choosing the wrong coding scheme for the next sequence of radio blocks because resegmentation is possible.
Addressing window
Before a sequence of coded radio link control packets or radio blocks can be transmitted over the Um (radio) interface, the transmitter must address the packets with an identification number. This information is then included in the header of every packet. The packets in GPRS are numbered from 1 to 128. After transmission of a sequence of packets (e.g., 10 packets), the transmitter asks the receiver to verify the correctness of the packets received in the form of an acknowledged/unacknowledged report. This report informs the transmitter which packet or packets were not successfully decoded and must be retransmitted. Since the number of packets is limited to 128 and the addressing window is 64, the packet Model Engineering College,Thrikkakara 10
EDGE sending process can run out of addresses after 64 packets. If an erroneously decoded packet must be retransmitted, it may have the same number as a new packet in the queue. If so, the protocol between the terminal and the network stalls, and all the packets belonging to the same low-layer capability frame must be retransmitted. In EGPRS, the addressing numbers have been increased to 2048 and the window has been increased to 1024 in order to minimize the risk for stalling. This, in turn, minimizes the risk for retransmitting low-layer capability frames and prevents decreased throughput.
Interleaving
To increase the performance of the higher coding schemes in EGPRS (MCS7 to MCS9) even at low C/I, the interleaving procedure has been changed within the EGPRS standard. When frequency hopping is used, the radio environment is changing on a per-burst level. Because a radio block is interleaved and transmitted over four bursts for GPRS, each burst may experience a completely different interference environment. If just one of the four bursts is not properly received, the entire radio block will not be properly decoded and will have to be retransmitted. In the case of CS4 for Model Engineering College,Thrikkakara 11
EDGE GPRS, hardly any error protection is used at all. With EGPRS, the standard handles the higher coding scheme differently than GPRS to combat this problem. MCS7, MCS8 and MCS9 actually transmit two radio blocks over the four bursts, and the interleaving occurs over two bursts instead of four. This reduces the number of bursts that must be retransmitted should errors occur. The likelihood of receiving two consecutive errorfree bursts is higher than receiving four consecutive errorfree bursts. This means that the higher coding schemes for EDGE have a better robustness with regard to frequency hopping.
12
EDGE
Link adaptation
Link adaptation uses the radio link quality, measured either by the mobile station in a downlink transfer or by the base station in an uplink transfer, to select the most appropriate modulation coding scheme for transmission of the next sequence of packets. For an uplink packet transfer, the network informs the mobile station which coding scheme to use for transmission of the next sequence of packets. The modulation coding scheme can be changed for each radio block (four bursts), but a change is usually initiated by new quality estimates. The practical adaptation rate is therefore decided by the measurement interval. There are three families: A, B and C. Within each family, there is a relationship between the payload sizes, which makes resegmentation for retransmissions possible.
13
EDGE
Incremental redundancy
Incremental redundancy initially uses a coding scheme, such as MCS9, with very little error protection and without consideration for the actual radio link quality. When information is received incorrectly, additional coding is transmitted and then soft combined in the receiver with the previously received information. Soft-combining increases the probability of decoding the information. This procedure will be repeated until the information is successfully decoded. This means that information about the radio link is not necessary to support incremental redundancy. For the mobile stations, incremental redundancy support is mandatory in the standard.
14
EDGE
EDGE Standardization
Standardization of the first releases of the thirdgeneration cellular systems that comply with ITU/IMT- 2000 requirements has now been finalized with European Telecommunications Standards Institute (ETSI/3GPP) Release 99. Two such major systems are Universal Mobile Telecommunications System (UMTS) and GSM/EDGE.
EDGE
Requirements on EDGE
From the beginning, the standardization of EDGE was restricted to the physical layer and to the introduction of a new modulation scheme. Since EDGE was intended as an evolution of the existing GSM radio access technology, the requirements were set accordingly: EDGE- and non-EDGE-capable mobile stations should be able to share one and the same time slot. EDGE- and non-EDGE-capable transceivers should be deployable in the same spectrum. A partial introduction of EDGE should be possible.
To ease implementation of new terminals while taking into account the asymmetrical characteristic of most services currently available, it was also decided that two classes of terminals should be supported by the EDGE standard: a terminal that provides 8PSK capability in the downlink only a terminal that provides 8PSK in the uplink and downlink.
16
EDGE
EDGE Bandwidth-secure mobile high speed LAN access File transfer Vertical applications such as batch-type field sales information or document transfer Real-time applications demanding a constant bit rate and transmission delay Time-critical wireless imaging Mobile videophony Video on demand Live video streaming
18
EDGE
Deployment of edge
All next-generation wireless networks have three main components: The radio infrastructure, which includes the cell sites. The packet core infrastructure, which handles only the packet-data traffic. The circuit-switched infrastructure, which includes the mobile switching centers (MSCs), and handles circuit-switched voice traffic. Eventually, as wireless networks evolve to an all-IP architecture, voice will also be packetized and travel over the packet core, and the circuit-switched infrastructure will be phased out. All current-generation wireless networks, regardless of technology, have circuit-switched infrastructure. The packet core is deployed when an operator migrates to GPRS, which is the first step toward 3G. Because EDGE is an upgrade to GPRS, it leverages the investments in the packet core and circuit-switched infrastructure by re-using them. The majority of the changes to deploy EDGE are in the radio infrastructure, where software and hardware are added at each cell site. This approach to migration benefits customers because their EDGE devices will work on GPRS networks, ensuring EDGE can use their GPRS devices on an EDGE network because of the forward and backward compatibility of the GPRS and EDGE technologies/networks.
19
EDGE
20
EDGE TDMA operators have the option of deploying a GSM/GPRS/EDGE overlay alongside their TDMA networks at 850 MHz and/or 1900 MHz. Analog operators have the option of deploying a GSM/GPRS/EDGE overlay alongside their 850 MHz networks. Signals travel farther at lower frequencies, so an 850 MHz EDGE deployment is particularly attractive because of the excellent propagation CHARACTERISTICS CELL sites covering large areas, thus reducing the number of sites necessary to cover a market with 3G. areas. One frequent operator concern, particularly for those with networks already at capacity, is whether they have enough spectrum to deploy a second network, especially when additional spectrum is expensive or unavailable. The solution is first to switch the existing network to a more efficient frequency re-use pattern, which frees up between 50-90% spectrum capacity. This additional capacity can then be used for the GSM/GPRS/EDGE network. Since GSM/GPRS is also much more spectrally efficient, GSM can support at least seven times more voice calls than analog and nearly twice as many as TDMA in the same amount of spectrum. Although EDGE is a data technology, it also helps boost the number of voice calls that a network can handle simultaneously by sending data more efficiently than GPRS. With EDGE transmitting more data into the same amount of bandwidth, the voice-coding or vocoder technology in the GSM voice network can be upgraded to a version thats expected to boost voice capacity between 15-20%. This makes EDGE particularly favorable for rural
21
EDGE
Advantages of Edge
Edges advantages can be divided into two categories: user benefits and operator benefits.
EDGE more than 90 countries as of April 2005. As a result, EDGE customers are always assured of having some level of packet-data service at home and when traveling. With dozens of major operators deploying EDGE networks on every major continent, EDGE will grow rapidly. Phone selection: Customers will have a variety of choices in devices and PC cards from leading manufacturers including LG Electronics, Motorola, Nokia, NEC America, Samsung, Siemens and Sony Ericsson. The devices support GSM/GPRS and work on multiple spectrum bands, including variations of 850/900/1800/1900 MHz.
EDGE operators to launch EDGE services quickly. The relatively low cost of the EDGE upgrade also means that operators can price their advanced services much more competitively than if the upgrade required replacing major elements of the radio infrastructure. Compatibility: EDGE is compatible with other technologies in the GSM migration path to 3G, so when customers with multi-mode phones and PC card modems move out of EDGE coverage, they're automatically switched to GPRS or WCDMA networks, depending the data services that they use. EDGE also re-uses the packet-data network infrastructure deployed for GPRS, making upgrade costs incremental rather than monumental. Cost-efficiency: Practical experience shows that the cost to upgrade to EDGE from GSM/GPRS is about $1-$2 per POP, given the upgrade only requires relatively simple software and hardware modifications. Volumes: More than 165 operators on every major continent have announced plans to deploy EDGE. As of May 2005, these operator commitments represented more than 871 million customers. In the Americas alone, 70 operators, representing more than 250 million potential captive customers, have publicly committed to EDGE. Cingular Wireless was the first operator to launch EDGE, in Indianapolis on June 30, 2003, and [then] AT&T Wireless [now Cingular Wireless] launched EDGE nationwide in November 2003. Operators in Canada, Mexico, South America, the Caribbean, Asia, Europe, This higher and Africa size have also launched into costs. high EDGE and of operator EDGE announcements of EDGE deployments worldwide continue to grow. market translates down volumes offers infrastructure and user devices, and one rule of business is that volumes drive EDGE affordable infrastructure for operators, and for the consumers it offers a wide range of price points on devices. EDGE also will be STANDARD Model Engineering College,Thrikkakara 24
EDGE FEATURE IN UMTS DEVICES without significantly increasing their cost. More control: EDGE includes sophisticated quality- of-service (QoS) mechanisms that give operators more control, ensuring that each application or customer gets the right amount of bandwidth. QoS is key for a service that targets enterprise customers, and it helps retain customers while reducing the need for cut-rate pricing to attract customers to replace those who have churned.
25
EDGE
Future of EDGE
The next evolutionary step for the GSM/EDGE cellular system includes enhancements of service provisioning for the packet-switched domain and increased alignment with the service provisioning in UMTS (Universal Mobile Telecommunications System) /UTRAN (UMTS terrestrial radio access network). These enhancements are currently being specified for the coming releases of the 3GPP standard. Based on EDGE high-speed transmission techniques combined with enhancements to the GPRS radio link interface, GERAN will provide improved support for all quality of service (QoS) classes defined for UMTS: interactive, background, streaming and conversational. By doing so, a new range of applications, including IP multimedia applications, will be adequately supported. This part of the GSM/EDGE evolution focuses on support for the conversational and streaming service classes, because adequate support for interactive and background services already exists. Additionally, multimedia applications will be supported by parallel simultaneous bearers with DIFFERENT QOS characteristics towards the same MS , such as multiple media streams handled through IMS domain. A driver for such evolution on the packet-switched side is the paradigm shift within the telecommunications world from circuit to packet-switched communications. Both the core network defined for GPRS and the current GSM/EDGE radio access network require modifications to support enhanced packet services. The GPRS/EGPRS networks can quickly and cost effectively evolve with market needs, and align with services provided by WCDMA networks.
26
EDGE
Conclusions
EDGE will provide the solution for operators wanting to offer personal multimedia services early and who need to increase the data capacity in their GSM network prior to UMTS deployment. EDGE is especially valuable for operators that do not deploy UMTS. EDGE will not replace existing investments or services but will upgrade them to a highly competitive level through gradual investment. EDGE rollout can satisfy increased data demand and produce increased revenues by first launching EDGE service in urban and office environments for business users and then providing wider area coverage as private usage takes off.
27
EDGE
Reference
Nokia White paper Ericsson White Paper www.3gamericas.org
28