Professional Documents
Culture Documents
Válvulas Alivio Presion Tanques
Válvulas Alivio Presion Tanques
Sizes 2 through 12
Modular construction
Model 1200A
PRESSURE / VACUUM
RELIEF VALVE
Model 1200A is designed to protect your tank from
damage created by over-pressure or excessive
vacuum. Costly product evaporation losses due to
normal tank breathing are greatly reduced.
Because the Model 1200A retains toxic vapors,
atmospheric contamination is minimized. This helps
to provide increased fire protection and safety.
MODEL 1200A
SPECIAL FEATURES
Model 1200A offers Groths special cushioned air
seating. Superior performing Teflon 1 seating
diaphragms are standard to minimize sticking
caused by resinous vapors and atmospheric moisture. The Model 1200A has a self draining housing
body and drip rings to protect seating surfaces from
condensate and freezing. This design also avoids
dangerous pressure or vacuum buildup due to
binding or clogging of the valve. Buna-N, Viton,
and other seating diaphragms can be provided
when required. To insure the proper alignment of
seating surfaces, there is peripheral guiding and a
center stabilizing system.
MODEL 1200A
MODEL 1201B
Groth Corporation, a Continental Disc company, Stafford, TX, USA
100
SPECIFICATIONS
AA
CC
A
BB
B
Specifications subject to change without notice. Certified dimensions available upon request.
Inlet
Flg
Max. Set
Pressure
Weight
Loaded
Max. Set
Vacuum.
Weight
Loaded
Max.
Setting
Spring
Loaded
Min.
Setting
Weight
Loaded
Max. W.P.
for Min.
Vacuum
Setting
Min. Vac.
Setting
for
Max. W.P.
A
B
Length Height
(mm) (mm)
C
Width
(mm)
12 oz/in2
13 5/8
13
(50 mm)
(52.7 gm/cm )
(346)
(330)
11 oz/in2
(80 mm)
(48.3 gm/cm2)
11 oz/in2
(100 mm)
(48.3 gm/cm )
18
(241)
(346)
(292)
19 3/4 15 7/8
(501)
13
(403)
(330)
27 3/4 22 1/4
(704)
19
(565)
(482)
16 oz/in2
(200 mm)
(70.3 gm/cm )
10
16 oz/in2
(250 mm)
(70.3 gm/cm2)
(1038)
(733)
(781)
12
16 oz/in2
46
32 7/8
36
(300 mm)
(70.3 gm/cm )
(1168)
(835)
(914)
(340)
BB
Height
(mm)
(505)
(457)
(70.3 gm/cm )
2
(1.05 kg. / cm )
16 oz/in2
16 oz/in2
(150 mm)
AA
Length
(mm)
(467)
(578)
19 1/2 27 1/2
(495)
(699)
CC
Width
(mm)
(241)
Approx. Ship
Wt. Lbs.
(Aluminum)
16
(7 kg)
13
21
(330)
(9 kg)
13
31
(330)
(14 kg)
(959)
(495)
57
(26 kg)
(669)
(600)
(854)
75
(1130)
(597)
38
53
25.1/2
116
(965)
(1346)
(648)
(53 kg)
(1413)
(648)
(34 kg)
157
(71 kg)
W.P. = Working Pressure. On spring loaded valves, change model number. 150# A.N.S.I. drilling compatibility, F.F. on aluminum and R.F. on carbon steel and stainless steel alloys.
Fiberglass dimensions on request. 16 oz/in2 set with spacer. S.S. set weights-Consult Factory. *Some sizes require non-ferrous components to achieve 0.5 oz./sq.in. setting.
HOW TO ORDER
For easy ordering, select proper model numbers
MODEL #
SIZE
MATERIAL
NOTES
1200A
1201B
1202B
1203A
Weight Loaded
Pressure Spring
Vacuum Spring
Pressure & Vacuum Springs
O = No Options
Z = Special Options
O = No Jacket
J = Steam Jacket
S = Spacer
H = Steam Jacket and Spacer
Diaphragm Material (Seat):
B = Buna-N
T = Teflon 1
V = Viton
Z = Special
Pallet Material
Seat Material
* Body Material
02"
Thru
12"
1
3
5
6
7
Z
EXAMPLE
OPTIONS
=
=
=
=
=
=
A
Aluminum
Carbon Steel
316 SS
Vinyl Ester Resin
Furan
Special
0
Indicates a 2" Model 1200A with Aluminum Body and Seat, 316 SS Pallet, Teflon 1 Seat Diaphragm and no other options.
1
101
Model 1200A
Set Pressure
(Ps)
In WC
0.87
1.00
1.73
2.00
2.60
3.00
3.46
4.00
6.00
8.00
10.0
12.0
15.0
20.0
25.0
30.0
Oz/Sq In
0.50
0.58
1.00
1.16
1.50
1.73
2.00
2.31
3.47
4.62
5.78
6.93
8.66
11.6
14.4
17.3
2
7.65
8.22
10.8
11.6
13.2
14.1
15.2
16.3
19.8
22.7
25.1
27.3
30.2
34.3
37.7
40.6
3
16.2
17.4
22.8
24.5
27.8
29.9
32.0
34.4
41.8
47.9
53.1
57.8
63.9
72.5
79.6
85.7
12
217
233
305
328
373
400
429
460
560
641
712
774
856
971
1067
1149
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1200A
4 In WC set pressure [Ps]
7 In WC flowing pressure [Pf]
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0
0.42
0.51
0.59
0.66
0.72
0.78
0.84
0.90
0.95
1
0.43
0.52
0.59
0.66
0.73
0.79
0.85
0.90
0.95
2
0.44
0.52
0.60
0.67
0.73
0.80
0.85
0.91
0.96
3
0.45
0.53
0.61
0.68
0.74
0.80
0.86
0.91
0.96
4
0.46
0.54
0.61
0.68
0.75
0.81
0.86
0.92
0.97
5
0.46
0.55
0.62
0.69
0.75
0.81
0.87
0.92
0.97
6
0.47
0.56
0.63
0.70
0.76
0.82
0.88
0.93
0.98
7
0.48
0.56
0.64
0.70
0.77
0.82
0.88
0.93
0.99
8
0.49
0.57
0.64
0.71
0.77
0.83
0.89
0.94
0.99
9
0.50
0.58
0.65
0.72
0.78
0.84
0.89
0.94
1.00
102
Model 1200A
Set Pressure
(Ps)
mm WC
22
50
75
100
125
150
175
200
225
250
275
300
375
500
625
750
mb
2.16
4.90
7.35
9.80
12.3
14.7
17.2
19.6
22.1
24.5
27.0
29.4
36.8
49.0
61.3
73.5
2
0.22
0.32
0.40
0.45
0.51
0.55
0.59
0.63
0.67
0.70
0.73
0.76
0.85
0.96
1.05
1.14
3
0.46
0.68
0.83
0.96
1.07
1.17
1.26
1.34
1.41
1.49
1.55
1.62
1.79
2.03
2.23
2.40
12
6.11
9.17
11.2
12.9
14.3
15.6
16.8
17.9
18.9
19.9
20.8
21.6
23.9
27.2
29.9
32.2
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1200A
100 mm WC Set Pressure [Ps]
175 mm WC Flowing Pressure [Pf]
103
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0
0.42
0.51
0.59
0.66
0.72
0.78
0.84
0.90
0.95
1
0.43
0.52
0.59
0.66
0.73
0.79
0.85
0.90
0.95
2
0.44
0.52
0.60
0.67
0.73
0.80
0.85
0.91
0.96
3
0.45
0.53
0.61
0.68
0.74
0.80
0.86
0.91
0.96
4
0.46
0.54
0.61
0.68
0.75
0.81
0.86
0.92
0.97
5
0.46
0.55
0.62
0.69
0.75
0.81
0.87
0.92
0.97
6
0.47
0.56
0.63
0.70
0.76
0.82
0.88
0.93
0.98
7
0.48
0.56
0.64
0.70
0.77
0.82
0.88
0.93
0.99
8
0.49
0.57
0.64
0.71
0.77
0.83
0.89
0.94
0.99
9
0.50
0.58
0.65
0.72
0.78
0.84
0.89
0.94
1.00
Model 1200A
Set Vacuum
(Ps)
In WC
0.87
1.00
1.73
2.00
2.60
3.00
3.46
4.00
6.00
8.00
10.0
12.0
15.0
20.0
25.0
30.0
Oz/Sq In
0.50
0.58
1.00
1.16
1.50
1.73
2.00
2.31
3.47
4.62
5.78
6.93
8.66
11.6
14.4
17.3
2
4.70
5.05
6.63
7.12
8.10
8.70
9.33
10.0
12.2
14.0
15.6
17.0
18.8
21.4
23.6
25.4
3
10.3
11.0
14.5
15.6
17.7
19.0
20.4
21.9
26.7
30.6
34.0
37.1
41.1
46.8
51.5
55.6
12
129
138
182
195
222
238
256
274
334
384
427
465
516
587
646
697
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1200A
4 In WC set vacuum [Ps]
7 In WC flowing vacuum [Pf]
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0
0.42
0.51
0.59
0.66
0.72
0.78
0.84
0.90
0.95
1
0.43
0.52
0.59
0.66
0.73
0.79
0.85
0.90
0.95
2
0.44
0.52
0.60
0.67
0.73
0.80
0.85
0.91
0.96
3
0.45
0.53
0.61
0.68
0.74
0.80
0.86
0.91
0.96
4
0.46
0.54
0.61
0.68
0.75
0.81
0.86
0.92
0.97
5
0.46
0.55
0.62
0.69
0.75
0.81
0.87
0.92
0.97
6
0.47
0.56
0.63
0.70
0.76
0.82
0.88
0.93
0.98
7
0.48
0.56
0.64
0.70
0.77
0.82
0.88
0.93
0.99
8
0.49
0.57
0.64
0.71
0.77
0.83
0.89
0.94
0.99
9
0.50
0.58
0.65
0.72
0.78
0.84
0.89
0.94
1.00
104
Model 1200A
Set Vacuum
(Ps)
mm WC
22
50
75
100
125
150
175
200
225
250
275
300
375
500
625
750
mb
2.16
4.90
7.35
9.80
12.3
14.7
17.2
19.6
22.1
24.5
27.0
29.4
36.8
49.0
61.3
73.5
2
0.13
0.20
0.24
0.28
0.31
0.34
0.37
0.39
0.42
0.44
0.46
0.48
0.53
0.60
0.66
0.72
3
0.29
0.44
0.53
0.62
0.69
0.75
0.81
0.86
0.91
0.96
1.00
1.04
1.16
1.32
1.45
1.57
12
3.65
5.48
6.70
7.72
8.60
9.40
10.1
10.8
11.4
12.0
12.6
13.1
14.5
16.5
18.2
19.6
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1200A
100 mm WC Set Vacuum [Ps]
175 mm WC Flowing Vacuum [Pf]
105
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0
0.42
0.51
0.59
0.66
0.72
0.78
0.84
0.90
0.95
1
0.43
0.52
0.59
0.66
0.73
0.79
0.85
0.90
0.95
2
0.44
0.52
0.60
0.67
0.73
0.80
0.85
0.91
0.96
3
0.45
0.53
0.61
0.68
0.74
0.80
0.86
0.91
0.96
4
0.46
0.54
0.61
0.68
0.75
0.81
0.86
0.92
0.97
5
0.46
0.55
0.62
0.69
0.75
0.81
0.87
0.92
0.97
6
0.47
0.56
0.63
0.70
0.76
0.82
0.88
0.93
0.98
7
0.48
0.56
0.64
0.70
0.77
0.82
0.88
0.93
0.99
8
0.49
0.57
0.64
0.71
0.77
0.83
0.89
0.94
0.99
9
0.50
0.58
0.65
0.72
0.78
0.84
0.89
0.94
1.00
Model 1201B
Set Pressure
(Ps)
PSIG
1.00
2.00
3.00
4.00
5.00
6.00
7.00
8.00
9.00
10.0
11.0
12.0
13.0
14.0
15.0
3
53.4
77.4
96.9
114
130
144
158
171
184
196
208
219
231
241
252
12
739
1070
1340
1577
1794
1997
2188
2371
2546
2714
2877
3036
3189
3339
3486
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1201B
4 PSIG set pressure [Ps]
7 PSIG flowing pressure [Pf]
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0.27
0.42
0.53
0.63
0.72
0.80
0.87
0.94
0.29
0.43
0.54
0.64
0.72
0.80
0.87
0.94
0.30
0.44
0.55
0.65
0.73
0.81
0.88
0.95
3
4
5
6
Consult Factory
0.32 0.33 0.35 0.36
0.45 0.47 0.48 0.49
0.56 0.57 0.58 0.59
0.66 0.67 0.67 0.68
0.74 0.75 0.76 0.76
0.82 0.82 0.83 0.84
0.89 0.90 0.90 0.91
0.96 0.96 0.97 0.97
0.38
0.50
0.60
0.69
0.77
0.85
0.92
0.98
0.39
0.51
0.61
0.70
0.78
0.85
0.92
0.99
0.40
0.52
0.62
0.71
0.79
0.86
0.93
1.00
106
Model 1201B
Set Pressure
(Ps)
BarG
0.07
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.50
0.55
0.60
0.70
0.80
0.90
1.00
3
1.57
1.89
2.36
2.76
3.14
3.48
3.81
4.12
4.41
4.70
4.98
5.25
5.76
6.25
6.72
7.18
12
21.7
26.2
32.6
38.3
43.4
48.2
52.7
57.0
61.1
65.1
68.9
72.6
79.7
86.5
93.1
99.4
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1201B
0.4 BarG Set Pressure [Ps]
0.7 BarG Flowing Pressure [Pf]
107
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0.27
0.42
0.53
0.63
0.72
0.80
0.87
0.94
0.29
0.43
0.54
0.64
0.72
0.80
0.87
0.94
0.30
0.44
0.55
0.65
0.73
0.81
0.88
0.95
3
4
5
Consult Factory
0.32 0.33 0.35
0.45 0.47 0.48
0.56 0.57 0.58
0.66 0.67 0.67
0.74 0.75 0.76
0.82 0.82 0.83
0.89 0.90 0.90
0.96 0.96 0.97
0.36
0.49
0.59
0.68
0.76
0.84
0.91
0.97
0.38
0.50
0.60
0.69
0.77
0.85
0.92
0.98
0.39
0.51
0.61
0.70
0.78
0.85
0.92
0.99
0.40
0.52
0.62
0.71
0.79
0.86
0.93
1.00
Model 1202B
Set Vacuum
(Ps)
PSIG
1.00
1.10
1.20
1.30
1.40
1.50
1.75
2.00
2.25
2.50
2.75
3.00
3.25
3.50
>3.50
12
422
442
460
478
495
511
548
582
613
641
667
691
713
732
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1202B
2 PSIG set vacuum [Ps]
3.5 PSIG flowing vacuum [Pf]
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0.27
0.42
0.53
0.63
0.72
0.80
0.87
0.94
0.29
0.43
0.54
0.64
0.72
0.80
0.87
0.94
0.30
0.44
0.55
0.65
0.73
0.81
0.88
0.95
3
4
5
6
Consult Factory
0.32 0.33 0.35 0.36
0.45 0.47 0.48 0.49
0.56 0.57 0.58 0.59
0.66 0.67 0.67 0.68
0.74 0.75 0.76 0.76
0.82 0.82 0.83 0.84
0.89 0.90 0.90 0.91
0.96 0.96 0.97 0.97
0.38
0.50
0.60
0.69
0.77
0.85
0.92
0.98
0.39
0.51
0.61
0.70
0.78
0.85
0.92
0.99
0.40
0.52
0.62
0.71
0.79
0.86
0.93
1.00
108
Model 1202B
Set Vacuum
(Ps)
BarG
0.07
0.10
0.11
0.12
0.13
0.14
0.15
0.16
0.17
0.18
0.19
0.20
0.22
0.24
>0.24
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1202B
0.12 BarG Set Vacuum [Ps]
0.17 BarG Flowing Vacuum [Pf]
109
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0.27
0.42
0.53
0.63
0.72
0.80
0.87
0.94
0.29
0.43
0.54
0.64
0.72
0.80
0.87
0.94
0.30
0.44
0.55
0.65
0.73
0.81
0.88
0.95
3
4
5
6
Consult Factory
0.32 0.33 0.35 0.36
0.45 0.47 0.48 0.49
0.56 0.57 0.58 0.59
0.66 0.67 0.67 0.68
0.74 0.75 0.76 0.76
0.82 0.82 0.83 0.84
0.89 0.90 0.90 0.91
0.96 0.96 0.97 0.97
0.38
0.50
0.60
0.69
0.77
0.85
0.92
0.98
0.39
0.51
0.61
0.70
0.78
0.85
0.92
0.99
0.40
0.52
0.62
0.71
0.79
0.86
0.93
1.00
Sizes 2 through 12
Pressure settings 0.5 oz/in2 to 15 PSIG
Vacuum settings 0.5 oz/in2 to 12 PSIG
Available in aluminum (type 356),
carbon steel, stainless steel and
other materials
Factory Mutual approved
flame arresters
Proven spiral wound, crimped
ribbon, flame element
Modular Construction
Model 1200A/7618
with Flame Arrester
SPECIAL FEATURES
MODEL 1200A/7618
MODEL 1200A/7618
110
SPECIFICATIONS
A
C
B
BB
Specifications subject to change without notice. Certified dimensions available upon request.
Max. Set
Pressure
Weight
Loaded
Inlet
Flg
Max. Set
Vacuum.
Weight
Loaded
Max.
Setting
Spring
Loaded
Min.
Setting
Weight
Loaded
Max. W.P.
for Min.
Vacuum
Setting
Min. Vac.
Setting
for
Max. W.P.
A
Length
(mm)
B
Height
(mm)
BB
Height
(mm)
C
Width
(mm)
Approx. Ship
Wt. Lbs.
(Aluminum)
12 oz/in2
13 5/8
27
33 7/8
9 1/2
35
(50 mm)
(52.7 gm/cm2)
(346)
(685)
(860)
(241)
(16 kg)
11 oz/in2
18
29 5/8
38 3/4
11 1/2
45
(80 mm)
(48.3 gm/cm )
(457)
(752)
(984)
(292)
(20 kg)
11 oz/in2
19 3/4
34 5/8
46 1/4
13
70
(100 mm)
(48.3 gm/cm )
(502)
(879)
(1175)
(330)
(32 kg)
28 3/4
43 1/4
58 3/4
19
125
(730)
(1099)
(1492)
(483)
(57 kg)
36
51 3/8
69 1/2
23 5/8
210
(914)
(1305)
(1765)
(600)
(95 kg)
(70.3 gm/cm )
2
16 oz/in2
(1.05 kg. / cm )
(150 mm)
16 oz/in2
16 oz/in2
(200 mm)
(70.3 gm/cm2)
10
16 oz/in2
42
58 7/8
83
30 3/4
350
(250 mm)
(70.3 gm/cm )
(1067)
(1495)
(2108)
(781)
(160 kg)
12
16 oz/in2
48 1/2
65 3/8
88 1/8
35 3/4
500
(300 mm)
(70.3 gm/cm )
(1232)
(1661)
(2238)
(908)
(227 kg)
W.P. = Working Pressure. On spring loaded valves, change model number. 150# A.N.S.I. drilling compatibility, F.F. on aluminum and R.F. on carbon steel and stainless steel alloys.
16 oz/in2 set with spacer. S.S. set weights-Consult Factory. *Some sizes require non-ferrous components to achieve 0.5 oz./sq.in. setting.
HOW TO ORDER
For easy ordering, select proper model numbers
MODEL #
SIZE
MATERIAL
NOTES
1200A/7618
1201B/7618
1202B/7618
1203A/7618
Weight Loaded
Pressure Spring
Vacuum Spring
Pressure & Vacuum Springs
02"
Thru
12"
O = No Options
Z = Special Options
O = No Jacket
J = Steam Jacket
S = Spacer
H = Steam Jacket and Spacer
Diaphragm Material (Seat):
B = Buna-N
T = Teflon 1
V = Viton
Z = Special
EXAMPLE
OPTIONS
=
=
=
=
Aluminum
Carbon Steel
316 SS
Special
Indicates a 2" Model 1200A/7618 with Aluminum Body and Seat, 316 SS Pallet, Teflon 1 Seat Diaphragm, Aluminum Flame Element and
no other options.
1
111
Model 1200/7618
Set Pressure
(Ps)
In WC
0.87
1.00
1.73
2.00
2.60
3.00
3.46
4.00
6.00
8.00
10.0
12.0
15.0
20.0
25.0
30.0
Oz/Sq In
0.50
0.58
1.00
1.16
1.50
1.73
2.00
2.31
3.47
4.62
5.78
6.93
8.66
11.6
14.4
17.3
2
3.01
3.29
4.56
4.96
5.76
6.26
6.79
7.36
9.20
10.9
12.3
13.6
15.4
18.0
20.4
22.6
3
5.98
6.68
9.70
10.7
12.6
13.7
15.0
16.3
20.6
24.3
27.6
30.6
34.6
40.7
46.0
50.9
12
62.3
72.0
112
125
148
163
178
195
249
295
335
372
422
497
563
623
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
Consult Factory for flow capacity with fiberglass valve.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1200A/7618
4 In WC set pressure [Ps]
7 In WC flowing pressure [Pf]
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0.75
0.81
0.87
0.92
0.97
0.76
0.82
0.88
0.93
0.98
0.77
0.82
0.88
0.93
0.99
0.77
0.83
0.89
0.94
0.99
0.78
0.84
0.89
0.94
1.00
Consult
Factory
0.72
0.78
0.84
0.90
0.95
0.73
0.79
0.85
0.90
0.95
0.73
0.80
0.85
0.91
0.96
0.74
0.80
0.86
0.91
0.96
0.75
0.81
0.86
0.92
0.97
112
Model 1200A/7618
Set Pressure
(Ps)
mm WC
22.0
50.0
75.0
100
150
200
250
300
375
500
625
750
3
0.18
0.30
0.39
0.46
0.58
0.69
0.78
0.87
0.98
1.15
1.30
1.44
12
1.91
3.53
4.62
5.53
7.05
8.35
9.50
10.5
12.0
14.1
15.9
17.6
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
Consult Factory for flow capacity with fiberglass valve.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
113
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0.75
0.81
0.87
0.92
0.97
0.76
0.82
0.88
0.93
0.98
0.77
0.82
0.88
0.93
0.99
0.77
0.83
0.89
0.94
0.99
0.78
0.84
0.89
0.94
1.00
Consult
Factory
0.72
0.78
0.84
0.90
0.95
0.73
0.79
0.85
0.90
0.95
0.73
0.80
0.85
0.91
0.96
0.74
0.80
0.86
0.91
0.96
0.75
0.81
0.86
0.92
0.97
Model 1200A/7618
Set Vacuum
(Ps)
In WC
0.87
1.00
1.73
2.00
2.60
3.00
3.46
4.00
6.00
8.00
10.0
12.0
15.0
20.0
25.0
30.0
Oz/Sq In
0.50
0.58
1.00
1.16
1.50
1.73
2.00
2.31
3.47
4.62
5.78
6.93
8.66
11.6
14.4
17.3
2
2.55
2.77
3.78
4.10
4.74
5.14
5.56
6.03
7.54
8.84
10.0
11.1
12.5
14.7
16.6
18.3
3
5.19
5.73
8.15
8.90
10.4
11.3
12.3
13.4
16.9
19.9
22.5
24.9
28.2
33.1
37.5
41.5
12
53.6
60.4
89.8
99.0
117
128
139
152
193
227
258
286
324
381
432
478
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
Consult Factory for flow capacity with fiberglass valve.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1200A/7618
4 In WC set vacuum [Ps]
7 In WC flowing vacuum [Pf]
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0.75
0.81
0.87
0.92
0.97
0.76
0.82
0.88
0.93
0.98
0.77
0.82
0.88
0.93
0.99
0.77
0.83
0.89
0.94
0.99
0.78
0.84
0.89
0.94
1.00
Consult
Factory
0.72
0.78
0.84
0.90
0.95
0.73
0.79
0.85
0.90
0.95
0.73
0.80
0.85
0.91
0.96
0.74
0.80
0.86
0.91
0.96
0.75
0.81
0.86
0.92
0.97
114
Model 1200A/7618
Set Vacuum
(Ps)
mm WC
22.0
50.0
75.0
100
150
200
250
300
375
500
625
750
3
0.15
0.25
0.32
0.38
0.48
0.56
0.63
0.70
0.80
0.93
1.06
1.17
12
1.60
2.78
3.59
4.27
5.42
6.40
7.27
8.06
9.10
10.7
12.2
13.5
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
Consult Factory for flow capacity with fiberglass valve.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
115
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0.75
0.81
0.87
0.92
0.97
0.76
0.82
0.88
0.93
0.98
0.77
0.82
0.88
0.93
0.99
0.77
0.83
0.89
0.94
0.99
0.78
0.84
0.89
0.94
1.00
Consult
Factory
0.72
0.78
0.84
0.90
0.95
0.73
0.79
0.85
0.90
0.95
0.73
0.80
0.85
0.91
0.96
0.74
0.80
0.86
0.91
0.96
0.75
0.81
0.86
0.92
0.97
Sizes 2 through 12
Modular construction
Model
1220A
with Pipe-Away Feature
MODEL 1220A
SPECIAL FEATURES
Model 1220A offers Groths special cushioned
air seating. Superior performing Teflon 1 seating
diaphragms are standard to minimize sticking
caused by resinous vapors and atmospheric
moisture. The Model 1220A has a self draining
housing body and drip rings to protect seating
surfaces from condensate and freezing. This
design also avoids pressure or vacuum buildup
due to binding or clogging of the valve. Buna-N,
Viton and other seating diaphragms can be provided when required. Model 1221B may be
spring loaded when required for use on blanketed tanks or other type installation requiring
higher settings. To insure the proper alignment of
seating surfaces there is peripheral guiding and a
center stabilizing stem.
MODEL 1220A
MODEL 1221B
120
120
SPECIFICATIONS
Specifications subject to change without notice. Certified dimensions available upon request.
Inlet
Flg.
Outlet
Flg.
Max. Set
Pressure
Weight
Loaded
11 oz/in
(50 mm)
(80 mm)
(48.2 gm/cm2)
(150 mm)
(200 mm)
10
(200 mm)
(250 mm)
10
(250 mm)
12
(300 mm)
12
(300 mm)
14
(350 mm)
16 oz/in2 11 oz/in2
(70.3 gm/cm2)
(48.3 gm/cm2)
16 oz/in2 16 oz/in2
(70.3 gm/cm )
2
(70.3 gm/cm )
2
16 oz/in2 16 oz/in2
(70.3 gm/cm2)
(70.3 gm/cm2)
BB
(mm)
(mm)
(mm)
(191)
(178)
15 1/8
(384)
(229)
11
9 1/2
(279)
(241)
5/8
(361)
(320)
18
(457)
(463)
Approx. Ship
Wt. Lbs.
(Aluminum)
5 19 5/8
1/2
(673)
(603)
(343)
32 1/2 28 1/2
(826)
16
(723)
37 3/4 34 1/2
(70.3 gm/cm2)
(959)
(876)
42 3/4 39 1/8
(70.3 gm/cm2)
(1086)
(993)
(499)
8 1/8
23 3/8
34
(206)
(152)
(594)
(16 kg)
6 1/2 28 5/8
(165)
(727)
(324)
(216)
(984)
(1149)
NOTES
Weight Loaded
Pressure Spring
Vacuum Spring
Pressure & Vacuum Springs
18
(457)
(318)
(1375)
21
20 5/8
15
58 7/8
260
(533)
(524)
(381)
(1496)
(118 kg)
12 1/2 54 1/8
1
3
5
6
7
Z
EXAMPLE
OPTIONS
O = No Options
Z = Special Options
O = No Jacket
J = Steam Jacket
S = Spacer
H = Steam Jacket and Spacer
Diaphragm Material (Seat):
B = Buna-N
T = Teflon 1
V = Viton
Z = Special
Pallet Material
Seat Material
* Body Material
02"
Thru
12"
=
=
=
=
=
=
A
Aluminum
Carbon Steel
316 SS
Vinyl Ester Resin
Furan
Special
0
Indicates a 2" Model 1220A with Aluminum Body and Seat, 316 SS Pallet, Teflon 1 Seat Diaphragm and no other options.
1
121
137
(483)
1220A
1221B
1222B
1223A
93
(42 kg)
19
HOW TO ORDER
MATERIAL
49
(22 kg)
(387)
W.P. = Working Pressure. On spring loaded valves, change model number. 150# R.F. drilling compatibility F.F. on aluminum and R.F. on carbon steel and stainless steel alloys.
Fiberglass dimensions on request. 16 oz/in2 set with spacer. S.S. set weights-Consult Factory. *Some sizes require non-ferrous components to achieve 0.5 oz./sq. in. setting.
SIZE
(12 kg)
(406)
MODEL #
26
(140)
16 oz/in2 16 oz/in2
(70.3 gm/cm2)
C
Width
(mm)
1/2
1/4
(489)
16 oz/in2 16 oz/in2
(70.3 gm/cm2)
B
Height
(mm)
19 1/4 18 1/4
(150 mm)
(48.3 gm/cm2)
(100 mm)
A
Length
(mm)
14 12 7
13 oz/in2 11 oz/in2
(57.0 gm/cm2)
Min. Vac.
Setting
for
Max. W.P.
(52.7 gm/cm2)
Max. W.P.
for Min.
Vacuum
Setting
12 oz/in
Min.
Setting
Weight
Loaded
4
(100 mm)
Max.
Setting
Spring
Loaded
3
(80 mm)
Max. Set
Vacuum
Weight
Loaded
(62 kg)
186
(85 kg)
Model 1220A
Set Pressure
(Ps)
In WC
0.87
1.00
1.73
2.00
2.60
3.00
3.46
4.00
6.00
8.00
10.0
12.0
15.0
20.0
25.0
30.0
Oz/Sq In
0.50
0.58
1.00
1.16
1.50
1.73
2.00
2.31
3.47
4.62
5.78
6.93
8.66
11.6
14.4
17.3
2
6.87
7.39
9.71
10.4
11.9
12.8
13.7
14.7
18.0
20.7
23.1
25.2
28.1
32.2
35.8
39.0
3
13.3
14.3
18.8
20.2
23.0
24.7
26.6
28.6
35.0
40.4
45.1
49.4
55.2
63.7
71.2
77.9
12
175
188
247
265
302
324
348
374
456
525
584
638
709
811
898
975
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1220A
4 In WC set pressure [Ps]
7 In WC flowing pressure [Pf]
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0
0.42
0.51
0.59
0.66
0.72
0.78
0.84
0.90
0.95
1
0.43
0.52
0.59
0.66
0.73
0.79
0.85
0.90
0.95
2
0.44
0.52
0.60
0.67
0.73
0.80
0.85
0.91
0.96
3
0.45
0.53
0.61
0.68
0.74
0.80
0.86
0.91
0.96
4
0.46
0.54
0.61
0.68
0.75
0.81
0.86
0.92
0.97
5
0.46
0.55
0.62
0.69
0.75
0.81
0.87
0.92
0.97
6
0.47
0.56
0.63
0.70
0.76
0.82
0.88
0.93
0.98
7
0.48
0.56
0.64
0.70
0.77
0.82
0.88
0.93
0.99
8
0.49
0.57
0.64
0.71
0.77
0.83
0.89
0.94
0.99
9
0.50
0.58
0.65
0.72
0.78
0.84
0.89
0.94
1.00
122
Model 1220A
Set Pressure
(Ps)
mm WC
22
50
75
100
125
150
175
200
225
250
275
300
375
500
625
750
mb
2.16
4.90
7.35
9.80
12.3
14.7
17.2
19.6
22.1
24.5
27.0
29.4
36.8
49.0
61.3
73.5
2
0.19
0.29
0.36
0.41
0.46
0.50
0.54
0.58
0.61
0.65
0.68
0.70
0.78
0.90
1.00
1.09
3
0.37
0.56
0.69
0.80
0.89
0.98
1.06
1.13
1.20
1.26
1.32
1.38
1.54
1.78
1.99
2.18
12
4.93
7.42
9.10
10.4
11.7
12.7
13.7
14.7
15.5
16.3
17.1
17.8
19.8
22.7
25.1
27.3
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1220A
100 mm WC Set Pressure [Ps]
175 mm WC Flowing Pressure [Pf]
123
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0
0.42
0.51
0.59
0.66
0.72
0.78
0.84
0.90
0.95
1
0.43
0.52
0.59
0.66
0.73
0.79
0.85
0.90
0.95
2
0.44
0.52
0.60
0.67
0.73
0.80
0.85
0.91
0.96
3
0.45
0.53
0.61
0.68
0.74
0.80
0.86
0.91
0.96
4
0.46
0.54
0.61
0.68
0.75
0.81
0.86
0.92
0.97
5
0.46
0.55
0.62
0.69
0.75
0.81
0.87
0.92
0.97
6
0.47
0.56
0.63
0.70
0.76
0.82
0.88
0.93
0.98
7
0.48
0.56
0.64
0.70
0.77
0.82
0.88
0.93
0.99
8
0.49
0.57
0.64
0.71
0.77
0.83
0.89
0.94
0.99
9
0.50
0.58
0.65
0.72
0.78
0.84
0.89
0.94
1.00
Model 1220A
Set Vacuum
(Ps)
In WC
0.87
1.00
1.73
2.00
2.60
3.00
3.46
4.00
6.00
8.00
10.0
12.0
15.0
20.0
25.0
30.0
Oz/Sq In
0.50
0.58
1.00
1.16
1.50
1.73
2.00
2.31
3.47
4.62
5.78
6.93
8.66
11.6
14.4
17.3
2
4.70
5.05
6.63
7.12
8.10
8.70
9.33
10.0
12.2
14.0
15.6
17.0
18.8
21.4
23.6
25.4
3
10.3
11.0
14.5
15.6
17.7
19.0
20.4
21.9
26.7
30.6
34.0
37.1
41.1
46.8
51.5
55.6
12
129
138
182
195
222
238
256
274
334
384
427
465
516
587
646
697
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1220A
4 In WC set vacuum [Ps]
7 In WC flowing vacuum [Pf]
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0
0.42
0.51
0.59
0.66
0.72
0.78
0.84
0.90
0.95
1
0.43
0.52
0.59
0.66
0.73
0.79
0.85
0.90
0.95
2
0.44
0.52
0.60
0.67
0.73
0.80
0.85
0.91
0.96
3
0.45
0.53
0.61
0.68
0.74
0.80
0.86
0.91
0.96
4
0.46
0.54
0.61
0.68
0.75
0.81
0.86
0.92
0.97
5
0.46
0.55
0.62
0.69
0.75
0.81
0.87
0.92
0.97
6
0.47
0.56
0.63
0.70
0.76
0.82
0.88
0.93
0.98
7
0.48
0.56
0.64
0.70
0.77
0.82
0.88
0.93
0.99
8
0.49
0.57
0.64
0.71
0.77
0.83
0.89
0.94
0.99
9
0.50
0.58
0.65
0.72
0.78
0.84
0.89
0.94
1.00
124
Model 1220A
Set Vacuum
(Ps)
mm WC
22
50
75
100
125
150
175
200
225
250
275
300
375
500
625
750
mb
2.16
4.90
7.35
9.80
12.3
14.7
17.2
19.6
22.1
24.5
27.0
29.4
36.8
49.0
61.3
73.5
2
0.13
0.20
0.24
0.28
0.31
0.34
0.37
0.39
0.42
0.44
0.46
0.48
0.53
0.60
0.66
0.72
3
0.29
0.44
0.53
0.62
0.69
0.75
0.81
0.86
0.91
0.96
1.00
1.04
1.16
1.32
1.45
1.57
12
3.65
5.48
6.70
7.72
8.60
9.40
10.1
10.8
11.4
12.0
12.6
13.1
14.5
16.5
18.2
19.6
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1220A
100 mm WC Set Vacuum [Ps]
175 mm WC Flowing Vacuum [Pf]
125
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0
0.42
0.51
0.59
0.66
0.72
0.78
0.84
0.90
0.95
1
0.43
0.52
0.59
0.66
0.73
0.79
0.85
0.90
0.95
2
0.44
0.52
0.60
0.67
0.73
0.80
0.85
0.91
0.96
3
0.45
0.53
0.61
0.68
0.74
0.80
0.86
0.91
0.96
4
0.46
0.54
0.61
0.68
0.75
0.81
0.86
0.92
0.97
5
0.46
0.55
0.62
0.69
0.75
0.81
0.87
0.92
0.97
6
0.47
0.56
0.63
0.70
0.76
0.82
0.88
0.93
0.98
7
0.48
0.56
0.64
0.70
0.77
0.82
0.88
0.93
0.99
8
0.49
0.57
0.64
0.71
0.77
0.83
0.89
0.94
0.99
9
0.50
0.58
0.65
0.72
0.78
0.84
0.89
0.94
1.00
Model 1221B
Set Pressure
(Ps)
PSIG
1.00
2.00
3.00
4.00
5.00
6.00
7.00
8.00
9.00
10.0
11.0
12.0
13.0
14.0
15.0
3
53.4
77.4
96.9
114
130
144
158
171
184
196
208
219
231
241
252
12
739
1070
1340
1577
1794
1997
2188
2371
2546
2714
2877
3036
3189
3339
3486
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1221B
4 PSIG set pressure [Ps]
7 PSIG flowing pressure [Pf]
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0.27
0.42
0.53
0.63
0.72
0.80
0.87
0.94
0.29
0.43
0.54
0.64
0.72
0.80
0.87
0.94
3
4
5
Consult Factory
0.30 0.32 0.33 0.35
0.44 0.45 0.47 0.48
0.55 0.56 0.57 0.58
0.65 0.66 0.67 0.67
0.73 0.74 0.75 0.76
0.81 0.82 0.82 0.83
0.88 0.89 0.90 0.90
0.95 0.96 0.96 0.97
0.36
0.49
0.59
0.68
0.76
0.84
0.91
0.97
0.38
0.50
0.60
0.69
0.77
0.85
0.92
0.98
0.39
0.51
0.61
0.70
0.78
0.85
0.92
0.99
0.40
0.52
0.62
0.71
0.79
0.86
0.93
1.00
126
Model 1221B
Set Pressure
(Ps)
BarG
0.07
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.50
0.55
0.60
0.70
0.80
0.90
1.00
3
1.57
1.89
2.36
2.76
3.14
3.48
3.81
4.12
4.41
4.70
4.98
5.25
5.76
6.25
6.72
7.18
12
21.7
26.2
32.6
38.3
43.4
48.2
52.7
57.0
61.1
65.1
68.9
72.6
79.7
86.5
93.1
99.4
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1221B
0.4 BarG Set Pressure [Ps]
0.7 BarG Flowing Pressure [Pf]
127
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0.27
0.42
0.53
0.63
0.72
0.80
0.87
0.94
0.29
0.43
0.54
0.64
0.72
0.80
0.87
0.94
3
4
5
Consult Factory
0.30 0.32 0.33 0.35
0.44 0.45 0.47 0.48
0.55 0.56 0.57 0.58
0.65 0.66 0.67 0.67
0.73 0.74 0.75 0.76
0.81 0.82 0.82 0.83
0.88 0.89 0.90 0.90
0.95 0.96 0.96 0.97
0.36
0.49
0.59
0.68
0.76
0.84
0.91
0.97
0.38
0.50
0.60
0.69
0.77
0.85
0.92
0.98
0.39
0.51
0.61
0.70
0.78
0.85
0.92
0.99
0.40
0.52
0.62
0.71
0.79
0.86
0.93
1.00
Model 1222B
Set Vacuum
(Ps)
PSIG
1.00
1.10
1.20
1.30
1.40
1.50
1.75
2.00
2.25
2.50
2.75
3.00
3.25
3.50
>3.50
12
422
442
460
478
495
511
548
582
613
641
667
691
713
732
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1222B
2 PSIG set vacuum [Ps]
3.5 PSIG flowing vacuum [Pf]
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0.27
0.42
0.53
0.63
0.72
0.80
0.87
0.94
0.29
0.43
0.54
0.64
0.72
0.80
0.87
0.94
3
4
5
Consult Factory
0.30 0.32 0.33 0.35
0.44 0.45 0.47 0.48
0.55 0.56 0.57 0.58
0.65 0.66 0.67 0.67
0.73 0.74 0.75 0.76
0.81 0.82 0.82 0.83
0.88 0.89 0.90 0.90
0.95 0.96 0.96 0.97
0.36
0.49
0.59
0.68
0.76
0.84
0.91
0.97
0.38
0.50
0.60
0.69
0.77
0.85
0.92
0.98
0.39
0.51
0.61
0.70
0.78
0.85
0.92
0.99
0.40
0.52
0.62
0.71
0.79
0.86
0.93
1.00
128
Model 1222B
Set Vacuum
(Ps)
BarG
0.07
0.10
0.11
0.12
0.13
0.14
0.15
0.16
0.17
0.18
0.19
0.20
0.22
0.24
>0.24
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1222B
0.12 BarG Set Vacuum [Ps]
0.17 BarG Flowing Vacuum [Pf]
129
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0.27
0.42
0.53
0.63
0.72
0.80
0.87
0.94
0.29
0.43
0.54
0.64
0.72
0.80
0.87
0.94
3
4
5
Consult Factory
0.30 0.32 0.33 0.35
0.44 0.45 0.47 0.48
0.55 0.56 0.57 0.58
0.65 0.66 0.67 0.67
0.73 0.74 0.75 0.76
0.81 0.82 0.82 0.83
0.88 0.89 0.90 0.90
0.95 0.96 0.96 0.97
0.36
0.49
0.59
0.68
0.76
0.84
0.91
0.97
0.38
0.50
0.60
0.69
0.77
0.85
0.92
0.98
0.39
0.51
0.61
0.70
0.78
0.85
0.92
0.99
0.40
0.52
0.62
0.71
0.79
0.86
0.93
1.00
Model 1220A/7618
Sizes 2 through 12
Modular construction
MODEL 1220A/7618
SPECIAL FEATURES
The Model 1220A Pressure/Vacuum relief valve with
flanged pipe-away outlet offers Groths special cushioned air seating. Superior performing Teflon 1
seating diaphragms are standard to minimize sticking
caused by resinous vapors and atmospheric moisture. Self draining housings and drip rings protect
seating surfaces from condensate and freezing.
The wafer construction of the Model 7618 flame
arrester affords easy accessibility to the flame bank
for maintenance. All Groth flame arresters utilize
spiral wound, crimped ribbon constructed flame
elements. These proven, Factory Mutual approved
elements, have been reported by NTIS of the
Dept. of Commerce, to provide the best flame
quenching performance for the least pressure drop.
Groth flame arresters are pneumatic tested to 15
PSIG as standard.
MODEL 1220A/7618
130
SPECIFICATIONS
A
E
BB
B
D
Specifications subject to change without notice. Certified dimensions available upon request.
Max. Set
Pressure
Weight
Loaded
Inlet
Flg.
Outlet
Flg.
(50 mm)
(80 mm)
(80 mm)
(100 mm)
Max. Set
Vacuum
Weight
Loaded
Max.
Setting
Spring
Loaded
Min.
Setting
Weight
Loaded
Max. W.P.
for Min.
Vacuum
Setting
Min. Vac.
Setting
for
Max. W.P.
A
Length
(mm)
11 oz/in2 12 oz/in2
(48.2 gm/cm2)
(361)
(150 mm)
(200 mm)
10
(200 mm)
(250 mm)
10
12
(250 mm)
(300 mm)
16 oz/in2 16 oz/in2
(70.3 gm/cm2)
(70.3 gm/cm2)
16 oz/in2 16 oz/in2
(70.3 gm/cm2)
(70.3 gm/cm2)
12
14
(300 mm)
(350 mm)
(mm)
(mm)
(854)
(221)
(514)
(457)
(790)
191/4
37
(489)
(940)
(673)
(1000)
(241)
Approx. Ship
Wt. Lbs.
(Aluminum)
(588)
(140)
(1203)
(1136)
(826)
(1518)
(1358)
60
(152)
(27 kg)
(292)
(679)
(165)
(419)
(1784)
(533)
(800)
(216)
373/8 103/4
(949)
(273)
16 oz/in2 16 oz/in2
(1638)
(2137)
(629)
(1149)
(70.3 gm/cm2)
(1086)
45
(20 kg)
(70.3 gm/cm2)
(70.3 gm/cm2)
C
Width
(mm)
16 oz/in2 16 oz/in2
(70.3 gm/cm2)
(676)
18
(48.3 gm/cm2)
16 oz/in2 11 oz/in2
(70.3 gm/cm2)
6
(150 mm)
(48.3 gm/cm2)
13 oz/in2 11 oz/in2
(100 mm)
BB
Height
(mm)
(52.7 gm/cm2)
(57.0 gm/cm2)
B
Height
(mm)
(1819)
(2321)
(727)
(1273)
(318)
90
(41 kg)
160
(73 kg)
270
(123 kg)
420
(190 kg)
15
600
(381)
(273 kg)
W.P. = Working Pressure. On spring loaded valves, change model number. 150# R.F. drilling compatibility F.F. on aluminum and R.F. on carbon steel and stainless steel alloys.
16 oz/in2 set with spacer. S.S. set weights-Consult Factory. *Some sizes require non-ferrous components to achieve 0.5 oz./sq.in. setting.
HOW TO ORDER
For easy ordering, select proper model numbers
MODEL #
NOTES
1220A/7618
1221B/7618
1222B/7618
1223A/7618
SIZE
Weight Loaded
Pressure Spring
Vacuum Spring
Pressure & Vacuum Springs
MATERIAL
02"
Thru
12"
O = No Options
Z = Special Options
O = No Jacket
J = Steam Jacket
S = Spacer
H = Steam Jacket and Spacer
Diaphragm Material (Seat):
B = Buna-N
T = Teflon 1
V = Viton
Z = Special
EXAMPLE
OPTIONS
=
=
=
=
Aluminum
Carbon Steel
316 SS
Special
Indicates a 2" Model 1220A/7618 with Aluminum Body and Seat, 316 SS Pallet, Teflon 1 Seat Diaphragm Aluminum Flame Element and
no other options.
1
131
Model 1220A/7618
Set Pressure
(Ps)
In WC
0.87
1.00
1.73
2.00
2.60
3.00
3.46
4.00
6.00
8.00
10.0
12.0
15.0
20.0
25.0
30.0
Oz/Sq In
0.50
0.58
1.00
1.16
1.50
1.73
2.00
2.31
3.47
4.62
5.78
6.93
8.66
11.6
14.4
17.3
2
2.92
3.19
4.45
4.84
5.64
6.12
6.65
7.21
9.07
10.7
12.1
13.3
15.1
17.7
20.0
22.2
3
5.68
6.34
9.23
10.1
11.9
13.0
14.1
15.4
19.5
23.0
26.1
28.9
32.7
38.4
43.5
48.1
12
59.1
67.8
105
116
138
151
165
180
230
272
309
343
389
457
518
574
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
Consult Factory for flow capacity with fiberglass valve.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1220A/7618
4 In WC set pressure [Ps]
7 In WC flowing pressure [Pf]
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0.75
0.81
0.87
0.92
0.97
0.76
0.82
0.88
0.93
0.98
0.77
0.82
0.88
0.93
0.99
0.77
0.83
0.89
0.94
0.99
0.78
0.84
0.89
0.94
1.00
Consult
Factory
0.72
0.78
0.84
0.90
0.95
0.73
0.79
0.85
0.90
0.95
0.73
0.80
0.85
0.91
0.96
0.74
0.80
0.86
0.91
0.96
0.75
0.81
0.86
0.91
0.97
132
Model 1220A/7618
Set Pressure
(Ps)
mm WC
22.0
50.0
75.0
100
150
200
250
300
375
500
625
750
3
0.17
0.29
0.37
0.44
0.55
0.65
0.74
0.82
0.93
1.09
1.23
1.36
12
1.80
3.28
4.27
5.11
6.51
7.70
8.75
9.70
11.0
13.0
14.7
16.3
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
Consult Factory for flow capacity with fiberglass valve.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
133
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0.75
0.81
0.87
0.92
0.97
0.76
0.82
0.88
0.93
0.98
0.77
0.82
0.88
0.93
0.99
0.77
0.83
0.89
0.94
0.99
0.78
0.84
0.89
0.94
1.00
Consult
Factory
0.72
0.78
0.84
0.90
0.95
0.73
0.79
0.85
0.90
0.95
0.73
0.80
0.85
0.91
0.96
0.74
0.80
0.86
0.91
0.96
0.75
0.81
0.86
0.91
0.97
Model 1220A/7618
Set Vacuum
(Ps)
In WC
0.87
1.00
1.73
2.00
2.60
3.00
3.46
4.00
6.00
8.00
10.0
12.0
15.0
20.0
25.0
30.0
Oz/Sq In
0.50
0.58
1.00
1.16
1.50
1.73
2.00
2.31
3.47
4.62
5.78
6.93
8.66
11.6
14.4
17.3
2
2.55
2.77
3.78
4.10
4.74
5.14
5.56
6.03
7.54
8.84
10.0
11.1
12.5
14.7
16.6
18.3
3
5.19
5.73
8.15
8.90
10.4
11.3
12.3
13.4
16.9
19.9
22.5
24.9
28.2
33.1
37.5
41.5
12
53.6
60.4
89.8
99.0
117
128
139
152
193
227
258
286
324
381
432
478
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
Consult Factory for flow capacity with fiberglass valve.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1220A/7618
4 In WC set vacuum [Ps]
7 In WC flowing vacuum [Pf]
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0.75
0.81
0.87
0.92
0.97
0.76
0.82
0.88
0.93
0.98
0.77
0.82
0.88
0.93
0.99
0.77
0.83
0.89
0.94
0.99
0.78
0.84
0.89
0.94
1.00
Consult
Factory
0.72
0.78
0.84
0.90
0.95
0.73
0.79
0.85
0.90
0.95
0.73
0.80
0.85
0.91
0.96
0.74
0.80
0.86
0.91
0.96
0.75
0.81
0.86
0.91
0.97
134
Model 1220A/7618
Set Vacuum
(Ps)
mm WC
22.0
50.0
75.0
100
150
200
250
300
375
500
625
750
3
0.15
0.25
0.32
0.38
0.48
0.56
0.63
0.70
0.80
0.93
1.06
1.17
12
1.60
2.78
3.59
4.27
5.42
6.40
7.27
8.06
9.10
10.7
12.2
13.5
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
Consult Factory for flow capacity with fiberglass valve.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
135
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0.75
0.81
0.87
0.92
0.97
0.76
0.82
0.88
0.93
0.98
0.77
0.82
0.88
0.93
0.99
0.77
0.83
0.89
0.94
0.99
0.78
0.84
0.89
0.94
1.00
Consult
Factory
0.72
0.78
0.84
0.90
0.95
0.73
0.79
0.85
0.90
0.95
0.73
0.80
0.85
0.91
0.96
0.74
0.80
0.86
0.91
0.96
0.75
0.81
0.86
0.91
0.97
Fiberglass
Relief Valves
SPECIAL FEATURES
Fiberglass valves offer Groths special cushioned air seating. Superior performing Teflon 1
seating diaphragms are standard to minimize
sticking caused by resinous vapors and atmospheric moisture. These valves have a self
draining housing body and drip rings to protect
seating surfaces from condensate and freezing.
This design also avoids pressure or vacuum
buildup due to binding or clogging of the valves.
These Fiberglass valves may be spring loaded
when required for use on blanketed tank or other
type installations requiring higher settings. To
insure the proper alignment of seating surfaces
there is peripheral guiding and a center stabilizing stem.
MODEL 1220A
160
CORROSION RESISTANCE
FIBERGLASS WITH
VINYL ESTER RESIN #411
FIBERGLASS
WITH FURAN RESIN
RESISTANT
RESISTANT
ACIDS:
Acetic
Acrylic
Boric
Chromic (20%)
Formic
Hydrochloric
Hydrofluoric *
Nitric (All Conc.)
Perchloric
Phosphoric
Sulfuric (75%)
BASES:
Potassium Hydroxide
Sodium Hydroxide *
Ammonium Hydroxide *
Ammonium Carbonate
Potassium Carbonate *
Sodium Carbonate *
WATER:
Demineralized
Distilled
SALTS:
Alum
Ammonium Chloride
Calcium Chloride
Ferric Chloride
Magnesium Sulfate
Sodium Chloride
Sodium Chromate
OTHERS:
Alcohols
Alum Chlorohydroxide
Glycerin
Sulfonated Detergents
Urea-Ammonium Nitrate
Fertilizers
BLEACHING AGENTS:
Calcium Chlorate
Calcium Hypochlorite
Chlorine Dioxide
Chlorine Water
Hydrogen Peroxide
Potassium
Permanganate
Sodium Chlorate
Sodium Hypochlorite
ACIDS:
Acetic
Acrylic
Chlorophenol
Hydrochloric
Nitric (5%)
Phosphoric
Sulfonic
Sulfuric (25%, 50%)
BASES:
Aniline
Diethylamine
Potassium Carbonate
Sodium Carbonate
Sodium Hydroxide
(5%, 50%)
SALTS:
Alum
Ammonium Bromide
Calcium Chloride
Ferric Chloride
Magnesium Sulfate
Sodium Chromate
WATER:
Demineralized
Distilled
SOLVENTS:
Acetone
Benzene
Carbon Disulfide
Carbon Tetrachloride
Chlorobenzene
Ethanol
Ethyl Acetate
Ethylene Dichloride
Methanol
Methyl Ethyl Ketone
Methyl Isobutyl Ketone
Perchloroethylene
Toluene
Trichloroethylene
Xylene
OTHERS:
Acrylonitrile
Benzyl Chloride
Cyclohexanone
Formalin
NON RESISTANT
Solvents
Oleum
NON RESISTANT
Phenol
Bromine
Furfural
Bleaching Agents
Free Halogens
Peroxides
161
SPECIAL FEATURES
Steam Jacketed Valves are built of corrosion
resistant materials throughout. Valve covers can
be easily removed for convenient inspection and
maintenance. Steam heated valves are suitable
for steam circulation up to 100 PSIG saturated.
170
HOW TO ORDER
For easy ordering, select proper model numbers
MODEL #
NOTES
SIZE
MATERIAL
3 = Carbon Steel
5 = 316 SS
Z = Special
Indicates a 2" Model 1200 with 316 SS Body, Seat and Pallet, Teflon
1
171
O = No Options
Z = Special Options
O = No Jacket
J = Steam Jacket
Diaphragm Material (Seat):
B = Buna-N
T = Teflon 1
V = Viton
M = Metal-to-Metal
Z = Special
Pallet Material
Seat Material
* Body Material
02"
Thru
12"
EXAMPLE
OPTIONS
5
1
SECTION 3
PRESSURE / VACUUM RELIEF VALVES
1260A Pressure Relief Valves w/Pipe-Away Feature
2300A Pressure Relief Valves
1300A Vacuum Relief Valves
1360A Vacuum Relief Valves
5000, 5100 Free Vents
6000, 6100 Gauge Hatch
6200 Gauge Hatch
Model 1260A
Sizes 2 through 12
Modular construction
PRESSURE
RELIEF VALVE
Pressure Relief Valve Model 1260A is for use
where pressure relief is required and all relieving
vapors must be piped away. Tank relief, to avoid
tank damage, is controlled by a spring or weight
loaded pallet in the valve housing. Pressure relief
valves help provide increased fire protection and
safety. The Model 1260A can also be used for inline vacuum relief where flanged inlet connection
is required. Back pressure in the system must be
considered when using flow curves.
MODEL 1260A
SPECIAL FEATURES
Model 1260A offers Groths special cushioned
air seating. Superior performing Teflon 1 seating
diaphragms are standard to minimize sticking
caused by resinous vapors and atmospheric
moisture. The Model 1260A has a self-draining
housing body and drip rings to protect seating
surfaces from condensate and freezing. This
design also avoids pressure or vacuum buildup
due to binding or clogging of the valve. Buna-N,
Viton and other seating diaphragms can be provided when required.
MODEL 1260A
MODEL 1261A
1
300
SPECIFICATIONS
A
B
BB
Specifications subject to change without notice. Certified dimensions available upon request.
Inlet
Flg.
Outlet
Flg.
Max. Set
Pressure
Weight
Loaded
Max. Set
Pressure
Spring
Loaded
Min.
Setting
Weight
Loaded
A
Length
(mm)
B
Height
(mm)
C
Width
(mm)
(mm)
(mm)
(mm)
Approx. Ship.
Wt. Lbs.
(Aluminum)
11 oz/in2
8 5/8
9 3/8
7 1/2
4 1/8
5 1/2
16 5/8
16
(80 mm)
(48.3 gm/cm )
(219)
(238)
(191)
(105)
(140)
(422)
(7 kg)
13 oz/in
10
11
20
22
(80 mm)
(100 mm)
(57.1 gm/cm2)
(254)
(282)
(229)
(127)
(152)
(514)
(10 kg)
11
13 7/8
11
6 1/2
6 1/2
25 5/8
29
(279)
(352)
(279)
(165)
(165)
(651)
(13 kg)
14 1/2
17 3/8
13 1/2
8 1/2
8 1/2
34 1/2
55
(368)
(441)
(343)
(216)
(216)
(876)
(25 kg)
18
21 1/4
16
9 3/4
10 3/4
39 3/4
92
(457)
(539)
(406)
(248)
(273)
(1010)
(42 kg)
16 oz/in2
(70.3 gm/cm2)
6
(150 mm)
4
(100 mm)
(50 mm)
1/8
BB
1/4
16 oz/in2
(150 mm)
(200 mm)
(70.3 gm/cm2)
10
16 oz/in2
(200 mm)
(250 mm)
(70.3 gm/cm2)
10
12
16 oz/in2
20 3/4
23 5/8
19
10 1/4
12 1/2
46 3/8
105
(250 mm)
(300 mm)
(70.3 gm/cm )
(527)
(600)
(483)
(260)
(318)
(1178)
(48 kg)
12
14
16 oz/in2
24 3/4
26 5/8
21
11
15
49 1/4
149
(300 mm)
(350 mm)
(70.3 gm/cm2)
(629)
(676)
(533)
(279)
(381)
(1251)
(68 kg)
On spring loaded valves, change model number. 150# R.F. drilling compatibility F.F. on aluminum and R.F. on carbon steel and stainless steel alloys.
Fiberglass dimensions on request. 16 oz/in2 set with spacer. S.S. set weights-Consult Factory. *Some sizes require non-ferrous components to achieve 0.5 oz/ sq. in. setting.
HOW TO ORDER
For easy ordering, select proper model numbers
MODEL #
NOTES
SIZE
MATERIAL
O = No Options
Z = Special Options
O = No Jacket
J = Steam Jacket
S = Spacer
H = Steam Jacket and Spacer
Diaphragm Material (Seat):
B = Buna-N
T = Teflon 1
V = Viton
Z = Special
Pallet Material
Seat Material
* Body Material
02"
Thru
12"
1
3
5
6
7
Z
EXAMPLE
OPTIONS
=
=
=
=
=
=
A
Aluminum
Carbon Steel
316 SS
Vinyl Ester Resin
Furan
Special
0
Indicates a 2" Model 1260A with Aluminum Body and Seat, 316 SS Pallet, Teflon 1 Seat Diaphragm and no other options.
1
301
Model 1260A
Set Pressure
(Ps)
In WC
0.87
1.00
1.73
2.00
2.60
3.00
3.46
4.00
6.00
8.00
10.0
12.0
15.0
20.0
25.0
30.0
Oz/Sq In
0.50
0.58
1.00
1.16
1.50
1.73
2.00
2.31
3.47
4.62
5.78
6.93
8.66
11.6
14.4
17.3
2
6.87
7.39
9.71
10.4
11.9
12.8
13.7
14.7
18.0
20.7
23.1
25.2
28.1
32.2
35.8
39.0
3
13.3
14.3
18.8
20.2
23.0
24.7
26.6
28.6
35.0
40.4
45.1
49.4
55.2
63.7
71.2
77.9
12
175
188
247
265
302
324
348
374
456
525
584
638
709
811
898
975
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps =Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1260A
4 In WC set pressure [Ps]
7 In WC flowing pressure [Pf]
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0
0.42
0.51
0.59
0.66
0.72
0.78
0.84
0.90
0.95
1
0.43
0.52
0.59
0.66
0.73
0.79
0.85
0.90
0.95
2
0.44
0.52
0.60
0.67
0.73
0.80
0.85
0.91
0.96
3
0.45
0.53
0.61
0.68
0.74
0.80
0.86
0.91
0.96
4
0.46
0.54
0.61
0.68
0.75
0.81
0.86
0.92
0.97
5
0.46
0.55
0.62
0.69
0.75
0.81
0.87
0.92
0.97
6
0.47
0.56
0.63
0.70
0.76
0.82
0.88
0.93
0.98
7
0.48
0.56
0.64
0.70
0.77
0.82
0.88
0.93
0.99
8
0.49
0.57
0.64
0.71
0.77
0.83
0.89
0.94
0.99
9
0.50
0.58
0.65
0.72
0.78
0.84
0.89
0.94
1.00
302
Model 1260A
Set Pressure
(Ps)
mm WC
22
50
75
100
125
150
175
200
225
250
275
300
375
500
625
750
mb
2.16
4.90
7.35
9.80
12.3
14.7
17.2
19.6
22.1
24.5
27.0
29.4
36.8
49.0
61.3
73.5
2
0.19
0.29
0.36
0.41
0.46
0.50
0.54
0.58
0.61
0.65
0.68
0.70
0.78
0.90
1.00
1.09
3
0.37
0.56
0.69
0.80
0.89
0.98
1.06
1.13
1.20
1.26
1.32
1.38
1.54
1.78
1.99
2.18
12
4.93
7.42
9.10
10.4
11.7
12.7
13.7
14.7
15.5
16.3
17.1
17.8
19.8
22.7
25.1
27.3
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1260A
100 mm WC Set Pressure [Ps]
175 mm WC Flowing Pressure [Pf]
303
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0
0.42
0.51
0.59
0.66
0.72
0.78
0.84
0.90
0.95
1
0.43
0.52
0.59
0.66
0.73
0.79
0.85
0.90
0.95
2
0.44
0.52
0.60
0.67
0.73
0.80
0.85
0.91
0.96
3
0.45
0.53
0.61
0.68
0.74
0.80
0.86
0.91
0.96
4
0.46
0.54
0.61
0.68
0.75
0.81
0.86
0.92
0.97
5
0.46
0.55
0.62
0.69
0.75
0.81
0.87
0.92
0.97
6
0.47
0.56
0.63
0.70
0.76
0.82
0.88
0.93
0.98
7
0.48
0.56
0.64
0.70
0.77
0.82
0.88
0.93
0.99
8
0.49
0.57
0.64
0.71
0.77
0.83
0.89
0.94
0.99
9
0.50
0.58
0.65
0.72
0.78
0.84
0.89
0.94
1.00
Model 1261A
Set Pressure
(Ps)
PSIG
1.00
2.00
3.00
4.00
5.00
6.00
7.00
8.00
9.00
10.0
11.0
12.0
13.0
14.0
15.0
3
53.4
77.4
96.9
114
130
144
158
171
184
196
208
219
231
241
252
12
739
1070
1340
1577
1794
1997
2188
2371
2546
2714
2877
3036
3189
3339
3486
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1261A
4 PSIG set pressure [Ps]
7 PSIG flowing pressure [Pf]
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0.27
0.42
0.53
0.63
0.72
0.80
0.87
0.94
0.29
0.43
0.54
0.64
0.72
0.80
0.87
0.94
3
4
5
Consult Factory
0.30 0.32 0.33 0.35
0.44 0.45 0.47 0.48
0.55 0.56 0.57 0.58
0.65 0.66 0.67 0.67
0.73 0.74 0.75 0.76
0.81 0.82 0.82 0.83
0.88 0.89 0.90 0.90
0.95 0.96 0.96 0.97
0.36
0.49
0.59
0.68
0.76
0.84
0.91
0.97
0.38
0.50
0.60
0.69
0.77
0.85
0.92
0.98
0.39
0.51
0.61
0.70
0.78
0.85
0.92
0.99
0.40
0.52
0.62
0.71
0.79
0.86
0.93
1.00
304
Model 1261A
Set Pressure
(Ps)
BarG
0.07
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.50
0.55
0.60
0.70
0.80
0.90
1.00
3
1.57
1.89
2.36
2.76
3.14
3.48
3.81
4.12
4.41
4.70
4.98
5.25
5.76
6.25
6.72
7.18
12
21.7
26.2
32.6
38.3
43.4
48.2
52.7
57.0
61.1
65.1
68.9
72.6
79.7
86.5
93.1
99.4
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1261A
0.4 BarG Set Pressure [Ps]
0.7 BarG Flowing Pressure [Pf]
305
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0.27
0.42
0.53
0.63
0.72
0.80
0.87
0.94
0.29
0.43
0.54
0.64
0.72
0.80
0.87
0.94
3
4
5
Consult Factory
0.30 0.32 0.33 0.35
0.44 0.45 0.47 0.48
0.55 0.56 0.57 0.58
0.65 0.66 0.67 0.67
0.73 0.74 0.75 0.76
0.81 0.82 0.82 0.83
0.88 0.89 0.90 0.90
0.95 0.96 0.96 0.97
0.36
0.49
0.59
0.68
0.76
0.84
0.91
0.97
0.38
0.50
0.60
0.69
0.77
0.85
0.92
0.98
0.39
0.51
0.61
0.70
0.78
0.85
0.92
0.99
0.40
0.52
0.62
0.71
0.79
0.86
0.93
1.00
Model 2300A
Sizes 2 through 12
Pressure settings 0.5 oz/in2 to 15 PSIG
Available in aluminum (type 356),
carbon steel, stainless steel and
other materials.
SPECIAL FEATURES
MODEL 2300A
Model 2300A is built of corrosion resistant material throughout. Groths self-closing special teflon
cushioned air pallet with center stabilizing stem
and peripheral guiding provides uniform seating
and alignment. Superior performing Teflon 1 seating diaphragms are standard to minimize sticking
caused by resinous vapors and atmospheric
moisture. The guides support a spun weatherhood which covers and protects the entire valve
structure. As added protection against the entry of
foreign matter, a mesh screen encircles the valve
under the weatherhood.
MODEL 2300A
MODEL 2301A
1
310
SPECIFICATIONS
AA
BB
B
Specifications subject to change without notice. Certified dimensions available upon request.
A
Diameter
(mm)
AA
Diameter
(mm)
B
Height
(mm)
BB
Height
(mm)
9 1/2
9 1/2
6 5/8
16 1/2
12
(50 mm)
(241)
(241)
(168)
(419)
(5 kg)
Size*
Flange
Maximum
Set
Pressure
Minimum
Set
Pressure
Approx. Ship
Wt. Lbs.
(Aluminum)
8 5/8
18 5/8
15
(330)
(219)
(467)
(7 kg)
13
13
10 9/16
22 1/2
20
(330)
(330)
(268)
(572)
(9 kg)
19
19 1/2
15
30 1/2
30
(482)
(495)
(381)
(784)
(14 kg)
23 5/8
23 1/2
16 5/8
35 3/8
45
(600)
(597)
(422)
(899)
(20 kg)
8
(200 mm)
(2.2 gm/cm )
**0.5 oz/in2 2
6
(150 mm)
(70.3 gm /cm )
(100 mm)
WEIGHT LOADED
13
(292)
11 1/2
16 oz/in2 WEIGHT LOADED
2
3
(80 mm)
10
30 3/4
25 1/2
17
41 3/8
65
(250 mm)
(781)
(648)
(431)
(1051)
(30 kg)
12
36
25 1/2
18
42 3/8
100
(300 mm)
(914)
(648)
(457)
(1076)
(45 kg
On spring-loaded valves, change to model 2301A. Larger sizes available - consult factory. * 150# A.N.S.I. drilling compatibility, F.F. on aluminum and R.F. on carbon steel and stainless steel alloys.
Fiberglass dimensions on request. **Some sizes require non-ferrous components to achieve 0.5 oz/ sq. in. setting.
HOW TO ORDER
For easy ordering, select proper model numbers
MODEL #
NOTES
SIZE
MATERIAL
O = No Options
Z = Special Options
O = No Jacket
J = Steam Jacket
S = Spacer
H = Steam Jacket and Spacer
Diaphragm Material (Seat):
B = Buna-N
T = Teflon 1
V = Viton
Z = Special
Pallet Material
Seat Material
* Body Material
02"
Thru
12"
1
3
5
6
7
Z
EXAMPLE
OPTIONS
=
=
=
=
=
=
A
Aluminum #
Carbon Steel
316 SS
Vinyl Ester Resin
Furan
Special
0
Indicates a 2" Model 2300A with Aluminum Body and Seat, 316 SS Pallet, Teflon 1 Seat Diaphragm and no other options.
1
311
Model 2300A
Set Pressure
(Ps)
In WC
0.87
1.00
1.73
2.00
2.60
3.00
3.46
4.00
6.00
8.00
10.0
12.0
15.0
20.0
25.0
30.0
Oz/Sq In
0.50
0.58
1.00
1.16
1.50
1.73
2.00
2.31
3.47
4.62
5.78
6.93
8.66
11.6
14.4
17.3
2
6.98
7.50
9.85
10.6
12.1
12.9
13.9
14.9
18.2
21.0
23.4
25.6
28.5
32.7
36.3
39.5
3
15.4
16.5
21.7
23.3
26.6
28.6
30.7
33.0
40.4
46.6
52.1
57.1
63.8
73.6
82.2
89.9
12
211
227
298
320
365
392
420
451
550
633
705
769
855
979
1084
1177
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
ExampleFlow Capacity Calculation
6 Model 2300A
4 In WC set pressure [Ps]
7 In WC flowing pressure [Pf]
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0
0.42
0.51
0.59
0.66
0.72
0.78
0.84
0.90
0.95
1
0.43
0.52
0.59
0.66
0.73
0.79
0.85
0.90
0.95
2
0.44
0.52
0.60
0.67
0.73
0.80
0.85
0.91
0.96
3
0.45
0.53
0.61
0.68
0.74
0.80
0.86
0.91
0.96
4
0.46
0.54
0.61
0.68
0.75
0.81
0.86
0.92
0.97
5
0.46
0.55
0.62
0.69
0.75
0.81
0.87
0.92
0.97
6
0.47
0.56
0.63
0.70
0.76
0.82
0.88
0.93
0.98
7
0.48
0.56
0.64
0.70
0.77
0.82
0.88
0.93
0.99
8
0.49
0.57
0.64
0.71
0.77
0.83
0.89
0.94
0.99
9
0.50
0.58
0.65
0.72
0.78
0.84
0.89
0.94
1.00
312
Model 2300A
Set Pressure
(Ps)
mm WC
22
50
75
100
125
150
175
200
225
250
275
300
375
500
625
750
mb
2.16
4.90
7.35
9.80
12.3
14.7
17.2
19.6
22.1
24.5
27.0
29.4
36.8
49.0
61.3
73.5
2
0.20
0.30
0.36
0.42
0.47
0.51
0.55
0.59
0.62
0.65
0.69
0.72
0.80
0.91
1.02
1.11
3
0.43
0.65
0.80
0.92
1.03
1.13
1.22
1.30
1.38
1.46
1.53
1.59
1.78
2.06
2.30
2.51
12
5.95
8.95
10.9
12.6
14.1
15.4
16.6
17.7
18.7
19.7
20.6
21.5
23.9
27.4
30.3
32.9
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
ExampleFlow Capacity Calculation
6 Model 2300A
100 mm WC Set Pressure [Ps]
175 mm WC Flowing Pressure [Pf]
313
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0
0.42
0.51
0.59
0.66
0.72
0.78
0.84
0.90
0.95
1
0.43
0.52
0.59
0.66
0.73
0.79
0.85
0.90
0.95
2
0.44
0.52
0.60
0.67
0.73
0.80
0.85
0.91
0.96
3
0.45
0.53
0.61
0.68
0.74
0.80
0.86
0.91
0.96
4
0.46
0.54
0.61
0.68
0.75
0.81
0.86
0.92
0.97
5
0.46
0.55
0.62
0.69
0.75
0.81
0.87
0.92
0.97
6
0.47
0.56
0.63
0.70
0.76
0.82
0.88
0.93
0.98
7
0.48
0.56
0.64
0.70
0.77
0.82
0.88
0.93
0.99
8
0.49
0.57
0.64
0.71
0.77
0.83
0.89
0.94
0.99
9
0.50
0.58
0.65
0.72
0.78
0.84
0.89
0.94
1.00
Model 2301A
Set Pressure
(Ps)
PSIG
1.00
2.00
3.00
4.00
5.00
6.00
7.00
8.00
9.00
10.0
11.0
12.0
13.0
14.0
15.0
3
59.9
87.7
111
131
151
169
186
203
219
235
250
265
280
295
309
12
739
1070
1340
1577
1794
1997
2188
2371
2546
2714
2877
3036
3189
3339
3486
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
ExampleFlow Capacity Calculation
6 Model 2301A
4 PSIG set pressure [Ps]
7 PSIG flowing pressure [Pf]
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0.27
0.42
0.53
0.63
0.72
0.80
0.87
0.94
0.29
0.43
0.54
0.64
0.72
0.80
0.87
0.94
3
4
5
Consult Factory
0.30 0.32 0.33 0.35
0.44 0.45 0.47 0.48
0.55 0.56 0.57 0.58
0.65 0.66 0.67 0.67
0.73 0.74 0.75 0.76
0.81 0.82 0.82 0.83
0.88 0.89 0.90 0.90
0.95 0.96 0.96 0.97
0.36
0.49
0.59
0.68
0.76
0.84
0.91
0.97
0.38
0.50
0.60
0.69
0.77
0.85
0.92
0.98
0.39
0.51
0.61
0.70
0.78
0.85
0.92
0.99
0.40
0.52
0.62
0.71
0.79
0.86
0.93
1.00
314
Model 2301A
Set Pressure
(Ps)
BarG
0.07
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.50
0.55
0.60
0.70
0.80
0.90
1.00
3
1.76
2.13
2.67
3.16
3.60
4.02
4.42
4.81
5.18
5.54
5.89
6.24
6.90
7.55
8.17
8.78
12
21.7
26.2
32.7
38.3
43.4
48.2
52.7
57.0
61.1
65.1
68.9
72.7
79.8
86.6
93.2
99.4
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-pressure.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-pressure directly from the table above. Use linear
interpolation if the set pressure is not listed. (Ref: Page TPD1)
If the allowable over-pressure is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-pressure is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-pressure by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OP = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-pressure according to the following
example.
ExampleFlow Capacity Calculation
6 Model 2301A
0.4 BarG Set Pressure [Ps]
0.7 BarG Flowing Pressure [Pf]
315
C Factor Table
%OP
10
20
30
40
50
60
70
80
90
0.27
0.42
0.53
0.63
0.72
0.80
0.87
0.94
0.29
0.43
0.54
0.64
0.72
0.80
0.87
0.94
3
4
5
Consult Factory
0.30 0.32 0.33 0.35
0.44 0.45 0.47 0.48
0.55 0.56 0.57 0.58
0.65 0.66 0.67 0.67
0.73 0.74 0.75 0.76
0.81 0.82 0.82 0.83
0.88 0.89 0.90 0.90
0.95 0.96 0.96 0.97
0.36
0.49
0.59
0.68
0.76
0.84
0.91
0.97
0.38
0.50
0.60
0.69
0.77
0.85
0.92
0.98
0.39
0.51
0.61
0.70
0.78
0.85
0.92
0.99
0.40
0.52
0.62
0.71
0.79
0.86
0.93
1.00
Model 1300A
Sizes 2 through 12
Modular construction
MODEL 1300A
SPECIAL FEATURES
Model 1300A offers Groths special cushioned
air seating. Superior performing Teflon 1 seating
diaphragms are standard to minimize sticking
caused by resinous vapors and atmospheric
moisture. The Model 1300A has a self draining
housing body and drip rings to protect seating
surfaces from condensate and freezing. This
design also avoids vacuum buildup due to binding or clogging of the vent. Metal-to-metal,
Buna-N, Viton and other seating diaphragms
can be provided when required.
MODEL 1300A
MODEL 1301A
320
SPECIFICATIONS
A
BB
B
Specifications subject to change without notice. Certified dimensions available upon request.
Max. Set
Vacuum
Weight
Loaded
Size
Max. Set
Vacuum
Spring
Loaded
Min. Set
Vacuum
Weight
Loaded
Max. W.P.
for Min. Vac.
Setting
Min. Vac.
Setting vs.
Max. W.P.
A
Length
(mm)
B
Height
(mm)
BB
Height
(mm)
C
Width
(mm)
Approx. Ship.
Wt. Lbs.
(Aluminum)
12 oz/in2
115/8
67/8
14
15
(50 mm)
(52.7 gm/cm )
(295)
(174)
(356)
(152)
(7 kg)
11 oz/in2
153/4
73/4
161/4
73/4
21
(80 mm)
(48.3 gm/cm )
(400)
(196)
(413)
(197)
(10 kg)
11 oz/in2
171/4
95/8
197/8
32
(100 mm)
(48.3 gm/cm2)
(438)
(244)
(505)
(229)
(14 kg)
16 oz/in2
231/2
117/8
27
12
61
(150 mm)
(70.3 gm/cm2)
(597)
(301)
(686)
(305)
(28 kg)
16 oz/in2
281/2
151/2
317/8
141/2
81
(200 mm)
(70.3 gm/cm )
(724)
(393)
(810)
(368)
(37 kg)
10
16 oz/in2
331/4
185/8
377/8
161/2
121
(250 mm)
(70.3 gm/cm )
(845)
(473)
(962)
(419)
(55 kg)
12
16 oz/in2
371/4
215/8
42
19
165
(300 mm)
(70.3 gm/cm2)
(946)
(549)
(1067)
(483)
(75 kg)
W.P. = Working Pressure. On spring loaded valves, change model number. 150# A.N.S.I. drilling compatibility, F.F. on aluminum and R.F. on carbon steel and stainless steel alloys.
Fiberglass dimensions on request. 16 oz/in2 set with spacer. S.S. set weights-Consult Factory. *Some sizes require non-ferrous components to achieve 0.5 oz./sq. in. setting.
HOW TO ORDER
For easy ordering, select proper model numbers
MODEL #
NOTES
SIZE
MATERIAL
O = No Options
Z = Special Options
O = No Jacket
J = Steam Jacket
S = Spacer
H = Steam Jacket and Spacer
Diaphragm Material (Seat):
B = Buna-N
T = Teflon 1
V = Viton
M = Metal-to-Metal
Z = Special
Pallet Material
Seat Material
* Body Material
02"
Thru
12"
1
3
5
6
7
Z
EXAMPLE
OPTIONS
=
=
=
=
=
=
A
Aluminum
Carbon Steel
316 SS
Vinyl Ester Resin
Furan
Special
0
Indicates a 2" Model 1300A with Aluminum Body and Seat, 316 SS Pallet, Teflon 1 Seat Diaphragm and no other options.
1
321
Model 1300A
Set Vacuum
(Ps)
In WC
0.87
1.00
1.73
2.00
2.60
3.00
3.46
4.00
6.00
8.00
10.0
12.0
15.0
20.0
25.0
30.0
Oz/Sq In
0.50
0.58
1.00
1.16
1.50
1.73
2.00
2.31
3.47
4.62
5.78
6.93
8.66
11.6
14.4
17.3
2
4.70
5.05
6.63
7.12
8.10
8.70
9.33
10.0
12.2
14.0
15.6
17.0
18.8
21.4
23.6
25.4
3
10.3
11.0
14.5
15.6
17.7
19.0
20.4
21.9
26.7
30.6
34.0
37.1
41.1
46.8
51.5
55.6
12
129
138
182
195
222
238
256
274
334
384
427
465
516
587
646
697
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1300A
4 In WC set vacuum [Ps]
7 In WC flowing vacuum [Pf]
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0
0.42
0.51
0.59
0.66
0.72
0.78
0.84
0.90
0.95
1
0.43
0.52
0.59
0.66
0.73
0.79
0.85
0.90
0.95
2
0.44
0.52
0.60
0.67
0.73
0.80
0.85
0.91
0.96
3
0.45
0.53
0.61
0.68
0.74
0.80
0.86
0.91
0.96
4
0.46
0.54
0.61
0.68
0.75
0.81
0.86
0.92
0.97
5
0.46
0.55
0.62
0.69
0.75
0.81
0.87
0.92
0.97
6
0.47
0.56
0.63
0.70
0.76
0.82
0.88
0.93
0.98
7
0.48
0.56
0.64
0.70
0.77
0.82
0.88
0.93
0.99
8
0.49
0.57
0.64
0.71
0.77
0.83
0.89
0.94
0.99
9
0.50
0.58
0.65
0.72
0.78
0.84
0.89
0.94
1.00
322
Model 1300A
Set Vacuum
(Ps)
mm WC
22
50
75
100
125
150
175
200
225
250
275
300
375
500
625
750
mb
2.16
4.90
7.35
9.80
12.3
14.7
17.2
19.6
22.1
24.5
27.0
29.4
36.8
49.0
61.3
73.5
2
0.13
0.20
0.24
0.28
0.31
0.34
0.37
0.39
0.42
0.44
0.46
0.48
0.53
0.60
0.66
0.72
3
0.29
0.44
0.53
0.62
0.69
0.75
0.81
0.86
0.91
0.96
1.00
1.04
1.16
1.32
1.45
1.57
12
3.65
5.48
6.70
7.72
8.60
9.40
10.1
10.8
11.4
12.0
12.6
13.1
14.5
16.5
18.2
19.6
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1300A
100 mm WC Set Vacuum [Ps]
175 mm WC Flowing Vacuum [Pf]
323
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0
0.42
0.51
0.59
0.66
0.72
0.78
0.84
0.90
0.95
1
0.43
0.52
0.59
0.66
0.73
0.79
0.85
0.90
0.95
2
0.44
0.52
0.60
0.67
0.73
0.80
0.85
0.91
0.96
3
0.45
0.53
0.61
0.68
0.74
0.80
0.86
0.91
0.96
4
0.46
0.54
0.61
0.68
0.75
0.81
0.86
0.92
0.97
5
0.46
0.55
0.62
0.69
0.75
0.81
0.87
0.92
0.97
6
0.47
0.56
0.63
0.70
0.76
0.82
0.88
0.93
0.98
7
0.48
0.56
0.64
0.70
0.77
0.82
0.88
0.93
0.99
8
0.49
0.57
0.64
0.71
0.77
0.83
0.89
0.94
0.99
9
0.50
0.58
0.65
0.72
0.78
0.84
0.89
0.94
1.00
Model 1301A
Set Vacuum
(Ps)
PSIG
1.00
1.10
1.20
1.30
1.40
1.50
1.75
2.00
2.25
2.50
2.75
3.00
3.25
3.50
>3.50
12
422
442
460
478
495
511
548
582
613
641
667
691
713
732
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1301A
2 PSIG set vacuum [Ps]
3.5 PSIG flowing vacuum [Pf]
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0.27
0.42
0.53
0.63
0.72
0.80
0.87
0.94
0.29
0.43
0.54
0.64
0.72
0.80
0.87
0.94
3
4
5
Consult Factory
0.30 0.32 0.33 0.35
0.44 0.45 0.47 0.48
0.55 0.56 0.57 0.58
0.65 0.66 0.67 0.67
0.73 0.74 0.75 0.76
0.81 0.82 0.82 0.83
0.88 0.89 0.90 0.90
0.95 0.96 0.96 0.97
0.36
0.49
0.59
0.68
0.76
0.84
0.91
0.97
0.38
0.50
0.60
0.69
0.77
0.85
0.92
0.98
0.39
0.51
0.61
0.70
0.78
0.85
0.92
0.99
0.40
0.52
0.62
0.71
0.79
0.86
0.93
1.00
324
Model 1301A
Set Vacuum
(Ps)
BarG
0.07
0.10
0.11
0.12
0.13
0.14
0.15
0.16
0.17
0.18
0.19
0.20
0.22
0.24
>0.24
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1301A
0.12 BarG Set Vacuum [Ps]
0.17 BarG Flowing Vacuum [Pf]
325
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0.27
0.42
0.53
0.63
0.72
0.80
0.87
0.94
0.29
0.43
0.54
0.64
0.72
0.80
0.87
0.94
3
4
5
Consult Factory
0.30 0.32 0.33 0.35
0.44 0.45 0.47 0.48
0.55 0.56 0.57 0.58
0.65 0.66 0.67 0.67
0.73 0.74 0.75 0.76
0.81 0.82 0.82 0.83
0.88 0.89 0.90 0.90
0.95 0.96 0.96 0.97
0.36
0.49
0.59
0.68
0.76
0.84
0.91
0.97
0.38
0.50
0.60
0.69
0.77
0.85
0.92
0.98
0.39
0.51
0.61
0.70
0.78
0.85
0.92
0.99
0.40
0.52
0.62
0.71
0.79
0.86
0.93
1.00
Model 1360A
Sizes 3 through 14
MODEL 1360A
SPECIAL FEATURES
Model 1360A offers Groths special cushioned
air seating. Superior performing Teflon 1 seating
diaphragms are standard to minimize sticking
caused by resinous vapors and atmospheric
moisture. The Model 1360A has a self draining
housing body and drip rings to protect seating
surfaces from condensate and freezing. This
design also avoids vacuum buildup due to binding or clogging of the vent. Metal-to metal,
Buna-N, Viton and other seating diaphragms
can be provided when required.
MODEL 1360A
MODEL 1361A
1
330
SPECIFICATIONS
A
B
BB
C
Specifications subject to change without notice. Certified dimensions available upon request.
Size
Flange
Max. Set
Vacuum
Weight
Loaded
Max. Set
Vacuum
Spring
Loaded
11 oz/in
(80 mm)
(48.2 gm/cm )
13 oz/in2
(100 mm)
(57.0 gm/cm )
16 oz/in2
(150 mm)
(70.3 gm/cm )
16 oz/in2
(200 mm)
(70.3 gm/cm )
10
16 oz/in2
(250 mm)
(70.3 gm/cm )
12
Min. Set
Vacuum
Weight
Loaded
Max. W.P.
for Min.
Vac.
Setting
Min. Vac.
Setting
vs.
Max. W.P.
A
Length
(mm)
B
Height
(mm)
C
Width
(mm)
(mm)
BB
Height
(mm)
5/8
1/4
1/2
5 1/2
16 1/4
12
(219)
(235)
(191)
(140)
(413)
(6 kg)
10
11 1/2
19 3/4
17
(254)
(292)
(229)
(152)
(502)
(8 kg)
11
14
11
6 1/2
24 5/8
23
(279)
(362)
(279)
(165)
(626)
(10 kg)
14 1/2
17 3/4
13 1/2
8 1/2
32 3/4
42
(368)
(451)
(343)
(216)
(832)
(19 kg)
18
21 1/4
16
10 3/4
38
71
(457)
(539)
(406)
(273)
(965)
(32 kg)
16 oz/in2
20 3/4
25 3/4
19
12 1/2
45 3/8
83
(300 mm)
(70.3 gm/cm )
(527)
(654)
(483)
(318)
(1153)
(38 kg)
14
16 oz/in2
24 3/4
29 1/4
21
15
48 3/4
118
(350 mm)
(70.3 gm/cm )
(629)
(742)
(533)
(381)
(1238)
(54 kg)
1}
4
Approx. Ship.
Wt. Lbs.
(Aluminum)
W.P. = Working Pressure. On spring loaded valves, change model number. 150# R.F. drilling compatibility F.F. on aluminum and R.F. on carbon steel and stainless steel alloys.
Fiberglass dimensions on request. 16 oz/in2 set with spacer. S.S. set weights-Consult Factory. *Some sizes require non-ferrous components to achieve 0.5 oz./sq. in. setting.
HOW TO ORDER
For easy ordering, select proper model numbers
MODEL #
NOTES
SIZE
MATERIAL
O = No Options
Z = Special Options
O = No Jacket
J = Steam Jacket
S = Spacer
H = Steam Jacket and Spacer
Diaphragm Material (Seat):
B = Buna-N
T = Teflon 1
V = Viton
Z = Special
Pallet Material
Seat Material
* Body Material
03"
Thru
14"
1
3
5
6
7
Z
EXAMPLE
OPTIONS
=
=
=
=
=
=
A
Aluminum
Carbon Steel
316 SS
Vinyl Ester Resin
Furan
Special
0
Indicates a 3" Model 1360A with Aluminum Body and Seat, 316 SS Pallet, Teflon 1 Seat Diaphragm , and no other options.
1
331
Model 1360A
Set Vacuum
(Ps)
In WC
0.87
1.00
1.73
2.00
2.60
3.00
3.46
4.00
6.00
8.00
10.0
12.0
15.0
20.0
25.0
30.0
Oz/Sq In
0.50
0.58
1.00
1.16
1.50
1.73
2.00
2.31
3.47
4.62
5.78
6.93
8.66
11.6
14.4
17.3
3
8.01
8.61
11.3
12.1
13.8
14.8
15.9
17.1
20.8
23.9
26.6
28.9
32.1
36.5
40.2
43.4
4
14.8
15.9
20.8
22.4
25.5
27.3
29.3
31.5
38.4
44.0
49.0
53.4
59.1
67.3
74.1
80.0
14
182
195
257
276
314
337
361
388
472
542
603
657
728
829
913
985
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1360A
4 In WC set vacuum [Ps]
7 In WC flowing vacuum [Pf]
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0
0.42
0.51
0.59
0.66
0.72
0.78
0.84
0.90
0.95
1
0.43
0.52
0.59
0.66
0.73
0.79
0.85
0.90
0.95
2
0.44
0.52
0.60
0.67
0.73
0.80
0.85
0.91
0.96
3
0.45
0.53
0.61
0.68
0.74
0.80
0.86
0.91
0.96
4
0.46
0.54
0.61
0.68
0.75
0.81
0.86
0.92
0.97
5
0.46
0.55
0.62
0.69
0.75
0.81
0.87
0.92
0.97
6
0.47
0.56
0.63
0.70
0.76
0.82
0.88
0.93
0.98
7
0.48
0.56
0.64
0.70
0.77
0.82
0.88
0.93
0.99
8
0.49
0.57
0.64
0.71
0.77
0.83
0.89
0.94
0.99
9
0.50
0.58
0.65
0.72
0.78
0.84
0.89
0.94
1.00
332
Model 1360A
Set Vacuum
(Ps)
mm WC
22
50
75
100
125
150
175
200
225
250
275
300
375
500
625
750
mb
2.16
4.90
7.35
9.80
12.3
14.7
17.2
19.6
22.1
24.5
27.0
29.4
36.8
49.0
61.3
73.5
3
0.23
0.34
0.41
0.48
0.53
0.58
0.63
0.67
0.71
0.74
0.78
0.81
0.90
1.02
1.13
1.21
4
0.42
0.63
0.76
0.88
0.98
1.07
1.16
1.23
1.30
1.37
1.43
1.49
1.65
1.88
2.08
2.24
14
5.12
7.70
9.41
10.8
12.1
13.2
14.2
15.2
16.0
16.9
17.6
18.4
20.4
23.2
25.5
27.6
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1360A
100 mm WC Set Vacuum [Ps]
175 mm WC Flowing Vacuum [Pf]
333
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0
0.42
0.51
0.59
0.66
0.72
0.78
0.84
0.90
0.95
1
0.43
0.52
0.59
0.66
0.73
0.79
0.85
0.90
0.95
2
0.44
0.52
0.60
0.67
0.73
0.80
0.85
0.91
0.96
3
0.45
0.53
0.61
0.68
0.74
0.80
0.86
0.91
0.96
4
0.46
0.54
0.61
0.68
0.75
0.81
0.86
0.92
0.97
5
0.46
0.55
0.62
0.69
0.75
0.81
0.87
0.92
0.97
6
0.47
0.56
0.63
0.70
0.76
0.82
0.88
0.93
0.98
7
0.48
0.56
0.64
0.70
0.77
0.82
0.88
0.93
0.99
8
0.49
0.57
0.64
0.71
0.77
0.83
0.89
0.94
0.99
9
0.50
0.58
0.65
0.72
0.78
0.84
0.89
0.94
1.00
Model 1361A
Set Vacuum
(Ps)
PSIG
1.00
1.10
1.20
1.30
1.40
1.50
1.75
2.00
2.25
2.50
2.75
3.00
3.25
3.50
>3.50
14
689
720
748
775
801
825
880
928
971
1009
1042
1070
1095
1115
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1361A
2 PSIG set vacuum [Ps]
3.5 PSIG flowing vacuum [Pf]
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0.27
0.42
0.53
0.63
0.72
0.80
0.87
0.94
0.29
0.43
0.54
0.64
0.72
0.80
0.87
0.94
3
4
5
Consult Factory
0.30 0.32 0.33 0.35
0.44 0.45 0.47 0.48
0.55 0.56 0.57 0.58
0.65 0.66 0.67 0.67
0.73 0.74 0.75 0.76
0.81 0.82 0.82 0.83
0.88 0.89 0.90 0.90
0.95 0.96 0.96 0.97
0.36
0.49
0.59
0.68
0.76
0.84
0.91
0.97
0.38
0.50
0.60
0.69
0.77
0.85
0.92
0.98
0.39
0.51
0.61
0.70
0.78
0.85
0.92
0.99
0.40
0.52
0.62
0.71
0.79
0.86
0.93
1.00
334
Model 1361A
Set Vacuum
(Ps)
BarG
0.07
0.10
0.11
0.12
0.13
0.14
0.15
0.16
0.17
0.18
0.19
0.20
0.22
0.24
>0.24
Flow capacity is certified by Groth Corporation, based on actual tests conducted in compliance with API Std. 2000.
Flow measurement accuracy has been verified by an independent testing laboratory.
Flow capacity values listed above are based on full open valves at 100% over-vacuum.
For an equivalent size fiberglass valve, reduce tabulated capacities by 32%.
Read the flow capacity at 100% over-vacuum directly from the table above. Use linear
interpolation if the set vacuum is not listed. (Ref: Page TPD1)
If the allowable over-vacuum is less than 100%, modify the flow capacity using the
appropriate C factor from the table. If allowable over-vacuum is more than 100%,
consult page TPD1 or your Groth Representative.
Calculate the percentage over-vacuum by the following formula. Note that all
pressures are gage pressure expressed in the same units of measure.
Pf = Flowing pressure
Ps = Set pressure
% OV = [(Pf - Ps)/Ps] x 100
Calculate flow capacity at less than 100% over-vacuum according to the following
example.
ExampleFlow Capacity Calculation
6 Model 1361A
0.12 BarG Set Vacuum [Ps]
0.17 BarG Flowing Vacuum [Pf]
335
C Factor Table
%OV
10
20
30
40
50
60
70
80
90
0.27
0.42
0.53
0.63
0.72
0.80
0.87
0.94
0.29
0.43
0.54
0.64
0.72
0.80
0.87
0.94
3
4
5
Consult Factory
0.30 0.32 0.33 0.35
0.44 0.45 0.47 0.48
0.55 0.56 0.57 0.58
0.65 0.66 0.67 0.67
0.73 0.74 0.75 0.76
0.81 0.82 0.82 0.83
0.88 0.89 0.90 0.90
0.95 0.96 0.96 0.97
0.36
0.49
0.59
0.68
0.76
0.84
0.91
0.97
0.38
0.50
0.60
0.69
0.77
0.85
0.92
0.98
0.39
0.51
0.61
0.70
0.78
0.85
0.92
0.99
0.40
0.52
0.62
0.71
0.79
0.86
0.93
1.00
FREE VENTS
Model 5000
Sizes 2 through 12
FREE VENTS
Model 5000 Series are designed to be used on
tanks containing non-volatile liquids and on vent
pipe extremities. Groth Free Vents offer efficient
flow capacity for the protection of the tank.
MODEL 5100
SPECIAL FEATURES
Model 5000 Series are built of corrosion resistant
materials throughout. A wire mesh screen prevents foreign matter from entering the tank or
pipe opening. Weather hoods are easily removable for inspection of vent and wire mesh screen.
MODEL 5000
MODEL 5000
MODEL 5100
Groth Corporation, a Continental Disc company, Stafford, TX, USA
350
SPECIFICATIONS
A
AA
B
BB
MODEL 5000
MODEL 5100
Specifications subject to change without notice. Certified dimensions available upon request.
Size*
Flange
A
Width
(Metric)
B
Height
(Metric)
Approx. Ship.
Wt. Lbs.
Size*
Flange
AA
Width
(Metric)
BB
Height
(Metric)
101/4
67/8
91/2
53/8
11
(51 mm)
(260)
(175)
(4 kg)
(51 mm)
(241)
(137)
(5 kg)
141/2
91/4
20
111/2
513/16
14
(76 mm)
(368)
(235)
(9 kg)
(76 mm)
(292)
(148)
(6 kg)
183/4
113/8
35
13
65/16
18
(102 mm)
(476)
(289)
(16 kg)
(102 mm)
(330)
(160)
(8 kg)
267/8
1511/16
70
17
73/8
28
(152 mm)
(683)
(398)
(32 kg)
(152 mm)
(432)
(187)
(13 kg)
351/8
201/8
135
191/2
91/4
42
(203 mm)
(892)
(511)
(61 kg)
(203 mm)
(495)
(235)
(19 kg)
10
433/8
24
235
10
231/2
105/8
60
(254 mm)
(1102)
(610)
(107 kg)
(254 mm)
(597)
(270)
(27 kg)
12
517/8
287/16
350
12
251/2
111/8
95
(305 mm)
(1318)
(722)
(159 kg)
(305 mm)
(648)
(283)
(43 kg)
HOW TO ORDER
For easy ordering, select proper model numbers
MODEL #
NOTES
5000
5100
SIZE
MATERIAL
OPTIONS
O = No Options
Z = Special Options
02"
Thru
12"
Body Material
3 = Carbon Steel
5 = 316 SS
Z = Special
EXAMPLE
351
Approx. Ship.
Wt. Lbs.
(CS / SS)
FREE VENTS
Model 5000
Flow Capacity
Tank Pressure
In W.C.
Oz/Sq In
10
12
1
2
3
4
6
8
10
15
20
25
30
35
40
45
50
55
60
0.58
1.16
1.73
2.31
3.47
4.62
5.78
8.66
11.6
14.4
17.3
20.2
23.1
26.0
28.9
31.8
34.7
3.34
4.72
5.78
6.67
8.17
9.44
10.5
12.9
14.9
16.7
18.2
19.7
21.0
22.3
23.5
24.6
25.7
7.34
10.4
12.7
14.7
18.0
20.8
23.2
28.4
32.8
36.6
40.1
43.3
46.3
49.1
51.7
54.2
56.6
12.7
17.9
21.9
25.3
31.0
35.8
40.0
48.9
56.5
63.1
69.1
74.6
79.7
84.5
89.1
93.4
97.5
28.6
40.5
49.5
57.2
70.0
80.9
90.4
111
128
143
156
169
180
191
201
211
220
49.6
70.2
85.9
99.2
121
140
157
192
221
248
271
293
313
332
349
366
382
78.2
111
135
156
192
221
247
303
349
390
427
461
493
523
551
577
603
112
159
194
224
275
317
354
434
501
560
613
662
707
750
790
828
864
12
10
Air Flow
1000 STD cubic feet per hour
8
6
4
3
2
352
FREE VENTS
Model 5000
Flow Capacity
Tank Pressure
mm H2O
25
50
75
100
150
200
250
375
500
625
750
875
1000
1125
1250
1375
1500
mb
2.45
4.90
7.35
9.80
14.7
19.6
24.5
36.8
49.0
61.3
73.5
85.8
98.0
110
123
135
147
3
0.21
0.29
0.36
0.41
0.51
0.58
0.65
0.80
0.92
1.03
1.13
1.22
1.30
1.38
1.45
1.52
1.59
6
0.80
1.14
1.39
1.61
1.97
2.27
2.54
3.11
3.59
4.01
4.39
4.74
5.07
5.37
5.66
5.94
6.20
10
2.20
3.11
3.81
4.40
5.38
6.21
6.95
8.50
9.81
11.0
12.0
13.0
13.9
14.7
15.5
16.2
16.9
12
3.15
4.46
5.46
6.30
7.72
8.91
9.96
12.2
14.1
15.7
17.2
18.6
19.9
21.1
22.2
23.3
24.3
12
10
8
6
4
3
2
8
1.39
1.97
2.41
2.79
3.41
3.94
4.41
5.39
6.23
6.96
7.62
8.22
8.79
9.32
9.82
10.3
10.7
Air Flow
1000 cubic meters per hour at 0C
4
0.36
0.50
0.62
0.71
0.87
1.01
1.12
1.38
1.59
1.77
1.94
2.10
2.24
2.38
2.50
2.62
2.74
FREE VENTS
Model 5000
Flow Capacity
Tank Vacuum
In W.C.
1
2
3
4
6
8
10
15
20
25
30
35
40
45
50
55
60
Oz/Sq In
0.58
1.16
1.73
2.31
3.47
4.62
5.78
8.66
11.6
14.4
17.3
20.2
23.1
26.0
28.9
31.8
34.7
3
6.11
8.63
10.6
12.2
14.9
17.1
19.1
23.2
26.6
29.6
32.2
34.5
36.6
38.5
40.3
42.0
43.5
4
10.5
14.9
18.2
21.0
25.6
29.5
32.9
40.0
45.9
51.0
55.4
59.4
63.1
66.4
69.5
72.3
75.0
6
23.8
33.6
41.1
47.4
57.9
66.7
74.4
90.5
104
115
125
134
143
150
157
164
169
8
41.3
58.3
71.3
82.3
100
116
129
157
180
200
217
233
247
260
272
284
294
10
65.1
91.9
112
130
158
182
203
247
284
315
343
367
390
411
430
447
463
12
93.4
132
161
186
227
262
292
355
407
452
491
527
559
589
616
641
665
12
10
Air Flow
1000 STD cubic feet per hour
8
6
4
3
2
354
FREE VENTS
Model 5000
Tank Vacuum
mm H2O
25
50
75
100
150
200
250
375
500
625
750
875
1000
1125
1250
1375
1500
mb
2.5
4.9
7.4
9.8
14.7
19.6
24.5
36.8
49.0
61.3
73.5
85.8
98.0
110
123
135
147
4
0.30
0.42
0.51
0.59
0.72
0.83
0.92
1.13
1.29
1.43
1.56
1.67
1.77
1.87
1.96
2.04
2.11
6
0.67
0.95
1.16
1.33
1.63
1.88
2.09
2.54
2.92
3.24
3.52
3.78
4.01
4.23
4.42
4.60
4.77
10
1.8
2.6
3.2
3.6
4.5
5.1
5.7
7.0
8.0
8.9
9.6
10.3
11.0
11.6
12.1
12.6
13.0
12
2.6
3.7
4.5
5.2
6.4
7.4
8.2
10.0
11.4
12.7
13.8
14.8
15.7
16.6
17.3
18.0
18.7
12
10
8
6
4
3
2
8
1.2
1.6
2.0
2.3
2.8
3.3
3.6
4.4
5.1
5.6
6.1
6.6
7.0
7.3
7.7
8.0
8.3
Air Flow
1000 cubic meters per hour at 0C
3
0.17
0.24
0.30
0.34
0.42
0.48
0.54
0.65
0.75
0.83
0.90
0.97
1.03
1.08
1.13
1.18
1.22
FREE VENTS
Model 5100
Flow Capacity
Tank Pressure
In W.C.
1
2
3
4
6
8
10
15
20
25
30
35
40
45
50
55
60
Oz/Sq In
0.58
1.16
1.73
2.31
3.47
4.62
5.78
8.66
11.6
14.4
17.3
20.2
23.1
26.0
28.9
31.8
34.7
3
8.32
11.8
14.4
16.6
20.4
23.5
26.3
32.2
37.2
41.5
45.5
49.1
52.4
55.6
58.6
61.4
64.1
4
14.3
20.3
24.8
28.7
35.1
40.5
45.3
55.5
64.0
71.5
78.3
84.6
90.4
95.8
101
106
110
6
32.4
45.8
56.1
64.8
79.4
91.7
102
125
145
162
177
191
204
217
228
239
250
8
56.2
79.5
97.4
112
138
159
178
217
251
281
307
332
354
376
396
415
433
10
88.6
125
154
177
217
251
280
343
396
442
484
523
559
592
624
654
683
12
127
180
220
254
311
359
402
492
568
634
695
750
801
850
895
938
980
12
10
Air Flow
1000 STD cubic feet per hour
8
6
4
3
2
356
FREE VENTS
Model 5100
Flow Capacity
Tank Pressure
mm H2O
25
50
75
100
150
200
250
375
500
625
750
875
1000
1125
1250
1375
1500
mb
2.45
4.90
7.35
9.80
14.7
19.6
24.5
36.8
49.0
61.3
73.5
85.8
98.0
110
123
135
147
3
0.23
0.33
0.41
0.47
0.57
0.66
0.74
0.90
1.04
1.17
1.28
1.38
1.47
1.56
1.65
1.73
1.80
6
0.91
1.29
1.58
1.82
2.23
2.58
2.88
3.53
4.07
4.55
4.98
5.38
5.74
6.09
6.42
6.73
7.02
10
2.49
3.52
4.31
4.98
6.10
7.04
7.87
9.64
11.1
12.4
13.6
14.7
15.7
16.6
17.5
18.4
19.2
12
3.57
5.05
6.19
7.14
8.75
10.1
11.3
13.8
16.0
17.8
19.5
21.1
22.5
23.9
25.2
26.4
27.5
12
10
8
6
4
3
2
8
1.58
2.23
2.74
3.16
3.87
4.47
4.99
6.11
7.06
7.88
8.63
9.32
10.0
10.6
11.1
11.7
12.2
Air Flow
1000 cubic meters per hour at 0C
4
0.40
0.57
0.70
0.81
0.99
1.14
1.27
1.56
1.80
2.01
2.20
2.38
2.54
2.69
2.84
2.97
3.11
FREE VENTS
Model 5100
Flow Capacity
Tank Vacuum
In W.C.
1
2
3
4
6
8
10
15
20
25
30
35
40
45
50
55
60
Oz/Sq In
0.58
1.16
1.73
2.31
3.47
4.62
5.78
8.66
11.6
14.4
17.3
20.2
23.1
26.0
28.9
31.8
34.7
3
6.72
9.49
11.6
13.4
16.4
18.8
21.0
25.5
29.3
32.5
35.4
37.9
40.3
42.4
44.4
46.2
47.8
6
26.2
37.0
45.2
52.2
63.7
73.4
81.8
99.6
114
127
138
148
157
165
173
180
186
8
45.4
64.1
78.5
90.5
111
127
142
173
198
220
239
256
272
286
300
312
323
10
71.6
101
124
143
174
201
224
272
312
347
377
404
429
452
473
492
510
12
103
145
177
205
250
288
321
390
448
497
541
580
615
648
678
705
731
12
10
8
Air Flow
1000 STD cubic feet per hour
4
11.6
16.4
20.0
23.1
28.2
32.5
36.2
44.0
50.5
56.1
61.0
65.4
69.4
73.1
76.4
79.6
82.5
6
4
3
2
358
FREE VENTS
Model 5100
Flow Capacity
Tank Vacuum
mm H2O
25
50
75
100
150
200
250
375
500
625
750
875
1000
1125
1250
1375
1500
mb
2.45
4.90
7.35
9.80
14.7
19.6
24.5
36.8
49.0
61.3
73.5
85.8
98.0
110
123
135
147
3
0.19
0.27
0.33
0.38
0.46
0.53
0.59
0.72
0.82
0.91
1.00
1.07
1.13
1.19
1.25
1.30
1.35
6
0.74
1.04
1.27
1.47
1.79
2.06
2.30
2.80
3.21
3.56
3.88
4.16
4.41
4.65
4.86
5.06
5.25
10
2.01
2.84
3.48
4.01
4.90
5.64
6.29
7.65
8.78
9.74
10.6
11.4
12.1
12.7
13.3
13.8
14.3
12
2.89
4.08
4.99
5.75
7.02
8.09
9.02
11.0
12.6
14.0
15.2
16.3
17.3
18.2
19.1
19.9
20.6
12
10
8
6
4
3
2
8
1.28
1.80
2.21
2.54
3.11
3.58
3.99
4.85
5.57
6.18
6.72
7.21
7.65
8.06
8.43
8.78
9.10
Air Flow
1000 cubic meters per hour at 0C
4
0.33
0.46
0.56
0.65
0.79
0.91
1.02
1.24
1.42
1.58
1.71
1.84
1.95
2.06
2.15
2.24
2.32
GAUGE HATCH
Model 6000
Sizes 4 through 10
GAUGE HATCH
Model 6000 Series provide access for gauging or
obtaining product samples from storage tanks.
The Model 6000 also provides pressure relief as
emergency venting. The Model 6100 incorporates a positive cover hold down which assures a
premium tight seal on tanks with internal pressures up to 3 PSIG. Gasketed covers are
recommended on tanks with high pressure settings. Model 6100 offers lock down capability.
MODEL 6100
SPECIAL FEATURES
Model 6000 Series is designed with a serrated
foot treadle surface to avoid foot slippage when
opening. This model permits the use of both
hands during gauging or sampling. Gravity will
close the cover upon removal of pressure on the
foot treadle. Groths special cushioned-air seating or metal-to-metal seatings available.
MODEL 6100
MODEL 6000
Groth Corporation, a Continental Disc company, Stafford, TX, USA
360
SPECIFICATIONS
B
B
Specifications subject to change without notice. Certified dimensions available upon request.
Size
A
Width
(Metric)
B
Height
(Metric)
Approx. Ship
Wt. Lbs.
(Aluminum)
10
(102 mm)
(254)
(152)
(3 Kg)
121/2
10
(152 mm)
(318)
(203)
(5 Kg.)
15
13
(203 mm)
(381)
(203)
(6 Kg)
10
173/4
17
(254 mm)
(451)
(229)
(8 Kg)
When gauge hatch includes the lock down feature, change model number to 6100. 150 # A.N.S.I. drilling compatibility, F.F. on aluminum, carbon steel and stainless steel alloys.
HOW TO ORDER
For easy ordering, select proper model numbers
MODEL #
NOTES
6000
6100
SIZE
MATERIAL
04"
Thru
10"
O = No Options
Z = Special Options
D = Drilled 150 # A.N.S.I.
U = Undrilled
Diaphragm Material (Seat):
B = Buna-N
T = Teflon 1
V = Viton
M = Metal-to-Metal
Z = Special
Material
1
3
5
Z
EXAMPLE
OPTIONS
=
=
=
=
Aluminum
Carbon Steel
316 SS
Special
Indicates a 4" Model 6000 with Aluminum material, Teflon 1 Diaphragm, Drilled Flange and no other options.
1
361
GAUGE HATCH
Model 6200
Size 8
GAUGE HATCH
Model 6200 provides access for gauging or
obtaining product samples from storage tanks.
The Model 6200 also provides pressure relief as
emergency venting.
MODEL 6200
SPECIAL FEATURES
Models 6200 will stay in the full open position
which will permit the use of both hands during
gauging or sampling. Units are mass produced in
type 356 aluminum cover and base with a BunaN seat insert. Optional seals are available.
370
SPECIFICATIONS
Specifications subject to change without notice. Certified dimensions available upon request.
Size
A
Width
(mm)
B
Height
(mm)
Approx.
Ship.
Wt. Lbs. (kg)
131/2
31/2
10
(200)
(343)
(89)
(5)
When gauge hatch includes the lock down feature, change model number to 6300. 150 # flat face A.N.S.I. drilling compatibility.
HOW TO ORDER
For easy ordering, select proper model numbers
MODEL #
6200
SIZE
MATERIAL
OPTIONS
O = No Options
Z = Special Options
08"
Material
NOTES
1 = Aluminum
* Buna-N is Standard;
Teflon seal not available
EXAMPLE
371