Professional Documents
Culture Documents
Low Dropout Voltage Regulator: Thermal Protection Noise Bypass
Low Dropout Voltage Regulator: Thermal Protection Noise Bypass
Low Dropout Voltage Regulator: Thermal Protection Noise Bypass
NJM2870F 56dB RR (DC < f < 60kHz) 66dB typ. (f=100Hz) 60dB typ. (f=1kHz) GOutput Noise Voltage Vno=30V (Cp=0.01F) GOutput Current Io(max.)=150mA GHigh Precision Output Vo2% GLow Dropout Voltage VI-O=0.12V typ. (Io=60mA, Vo1.8V) GInput Voltage range +2+14V (Vo=1.5V Version) GON/OFF Control (Active High) GOutput capacitor with 4.7uF ceramic capacitor GInternal Short Circuit Current Limit GInternal Thermal Overload Protection GBipolar Technology GPackage Outline MTP5 (MTP5: 2.82.91.1mm)
I PIN CONFIGURATION
1 2 3 4 5
PIN FUNCTION 1. CONTROL (Active High) 2. GND 3. NOISE BYPASS 4. VOUT 5. VIN
VOUT
Thermal Protection Noise Bypass
Bandgap Reference
GND
NJM2870
I ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL Input Voltage VIN Control Voltage VCONT Power Dissipation PD Operating Temperature Topr Storage Temperature Tstg (Ta=25C) RATINGS UNIT +14 V +14(note 1) V 200 mW 40 +85 C 40 +125 C (note 1) When input voltage is less than +14V, the absolute maximum control voltage is equal to the input voltage. I ELECTRICAL CHARACTERISTICS (VIN=Vo+1V, CIN=0.1F, Co=4.7F, Cp=0.01F, Ta=25C) PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. Io=30mA Output Voltage Vo +2% 2% Io=0mA, expect Icont Quiescent Current 200 300 IQ Quiescent Current 100 IQ(OFF) VCONT=0V at Control OFF Output Current Io 150 200 Vo0.3V Line Regulation 0.10 Vo/VIN VIN=Vo+1V Vo+6V, Io=30mA Load Regulation 0.03 Vo/Io Io=0 100mA Dropout Voltage 0.12 0.2 VI-O Io=60mA Ripple Rejection ein=200mVrms,f=1kHz, Io=10mA 60 RR VIN=Vo+2V, Vo=3V Version Average Temperature Ta=085C, Io=10mA, 0.2 Vo/Ta Coefficient of Output Voltage Vo=3V Version f=10Hz80kHz, Io=10mA, Output Noise Voltage VNO 30 Vo=3V Version Control Voltage for ON-state 1.6 VCONT(ON) Control Voltage for OFF-state VCONT(OFF) 0.6 (note 2) The above specification is a common specification for all output voltages. Therefore, it may be different from the individual specification for a specific output voltage. I ELECTRICAL CHARACTERISTICS (Vo=1.5V Version, VIN=2.4V, CIN=0.1F, Co=4.7F, Cp=0.01F, Ta=25C) PARAMETER SYMBOL TEST CONDITION MIN. Io=30mA Output Voltage Vo 2% Io=0mA, expect Icont Quiescent Current IQ Quiescent Current IQ(OFF) VCONT=0V at Control OFF Output Current Io 150 Vo0.3V Line Regulation Vo/VIN VIN=Vo+1V Vo+6V, Io=30mA Load Regulation Vo/Io Io=0 100mA Ripple Rejection ein=200mVrms,f=1kHz, Io=10mA RR VIN=Vo+2V Average Temperature Vo/Ta Ta=085C, Io=10mA Coefficient of Output Voltage Output Noise Voltage VNO f=10Hz80kHz, Io=10mA, Control Voltage for ON-state VCONT(ON) 1.6 Control Voltage for OFF-state VCONT(OFF)
MAX. UNIT +2% V 300 A 100 nA mA 0.10 %/V 0.03 %/mA 0.6 dB mV/C Vrms V V
NJM2870
I OUTPUT VOLTAGE RANK LIST Device Name NJM2870F15 NJM2870F18 NJM2870F19 NJM2870F02 NJM2870F21 NJM2870F23 NJM2870F24 NJM2870F25 NJM2870F26 VOUT 1.5V 1.8V 1.9V 2.0V 2.1V 2.3V 2.4V 2.5V 2.6V Device Name NJM2870F27 NJM2870F28 NJM2870F285 NJM2870F29 NJM2870F03 NJM2870F31 NJM2870F32 NJM2870F33 NJM2870F34 VOUT 2.7V 2.8V 2.85V 2.9V 3.0V 3.1V 3.2V 3.3V 3.4V Device Name NJM2870F35 NJM2870F36 NJM2870F38 NJM2870F04 NJM2870F45 NJM2870F46 NJM2870F47 NJM2870F48 NJM2870F05 VOUT 3.5V 3.6V 3.8V 4.0V 4.5V 4.6V 4.7V 4.8V 5.0V
I TEST CIRCUIT
A
VIN
IIN +
0.1F
VIN
VOUT +
NJM2870
4.7F
IOUT V VOUT
(tantalum)
A V VCONT
ICONT
CONTROL
NOISE BYPASS
GND
Cp=0.01F
NJM2870
I TYPICAL APPLICATION x In case that ON/OFF Control is not required: VIN
0.1F R (0 300k)
VIN
VOUT
VOUT
4.7F
NJM2870
(ceramic or tantalum)
GND
Cp=0.01F
Connect control terminal to VIN terminal The quiescent current can be reduced by using a resistance R. Instead, it increases the minimum operating voltage. For further information, please refer to Figure Output Voltage vs. Control Voltage.
0.1F R
NJM2870
(ceramic or tantalum)
CONTROL
NOISE BYPASS
GND
Cp=0.01F
State of control terminal: H output is enabled. L or open output is disabled. Noise bypass Capacitance Cp
Noise bypass capacitance Cp reduces noise generated by band-gap reference circuit.
Noise level and ripple rejection will be improved when larger Cp is used.
Use of smaller Cp value may cause oscillation. Use the Cp value of 0.01uF greater to avoid the problem.
NJM2870
I TYPICAL CHARACTERISTICS
NJM2870
I TYPICAL CHARACTERISTICS
NJM2870
I TYPICAL CHARACTERISTICS
NJM2870
[CAUTION] The specifications on this databook are only given for information , without any guarantee as regards either mistakes or omissions. The application circuits in this databook are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights.