Professional Documents
Culture Documents
4410 - Section A - Hose PDF
4410 - Section A - Hose PDF
Hose
HOSE
Coalmaster Hydraulic Suction and Return Push-Lok Plus Transportation
www.parkerhose.com
Catalog 4410 US
Coalmaster Hose
A-7
A-9
451ST
Equipment
C
Extreme Tough Cover SAE 100R15 811HT A-13 Transportation Hose ParMax - 8,000 psi
1/2 SAE Minimum Bend Radius SAE 100R4 A-14 271 A-14
213
Accessories
Push-Lok Plus
E
A-2
Hose Products Division Parker Hannifin Corporation Wickliffe, Ohio www.parkerhose.com
Catalog 4410 US
Parker Hose Nomenclature Parker offers a wide variety of hoses including braided, Example: 451TC-8 spiral, multi-purpose, transportation, refrigerant, 451TC-8 - Hose Type LP gas and more. Parkers product line has been 451TC-8 - Indicates the special feature of the tested and approved to meet and exceed global stan hose (in this case,Tough Cover) dards. Our hoses range in size from 3/16 to 3 I.D. 451TC-8 - Hose inside diameter dash size (in this case, 8/16 or 1/2) and are compatible with crimp and field-attachable style fittings. Specific hose information is displayed throughout Catalog 4400, Section A. Hose page content is defined by the information shown below. Please take a moment and review.
Hose Outer Diameter A critical measurement when considering hose clamps and applications where envelope size is limited. Hose Inner Diameter Measured in 1/16 inch increments identified by use of a dash(-) numbering system. i.e., 4/16 = 1/4 = -4.
Hose Working Pressure Should have a working pressure rating meeting or exceeding the maximum operating pressure of the system. Maximum rating listed below in which the hose is to be used.
Minimum Bend Radius Is the smallest arc that the hose can be bent before its life is greatly reduced. Exceeding the bend radius can cause kinking, inner tube washout, and excessive stress on reinforcement. Weight Provided by the foot for instances where it is a critical parameter in the design of the system. Approved Fitting To be used with the hose. Could be crimped or field attachable. Lists hose part numbers on page
For more information regarding hose application and temperature, see the Technical Section (Section E) Indicates fitting size is available.
E
A-3
Hose Products Division Parker Hannifin Corporation Wickliffe, Ohio www.parkerhose.com
Technical
Accessories
Hose Information Base part number Description SAE, ISO, and EN specifica- tions
Equipment
Fittings
Catalog 4410 US
Box 1
F
Box 2
436
Box 3
06
Box 4
39
Box 5
08
Box 6
08
Box 7
08
Box 8
Box 9
-24
Box 10
Box 11
Parker 436-8
OAL
Box 7: Symbol
Fittings
Symbol
F = P= Y= K=
Parkrimp Crimp Fittings (i.e 43 Series) Parkrimp Crimp Fittings (i.e 26 Series) Permanent Crimp Fittings(i.e HY Series) Permanent Crimp Fittings (i.e 81 Series)
08 =
Box 8: Symbol
Box 2: Symbol
436 =
Equipment
No Suffix = Steel B= Brass C= 316 Stainless Steel BA= Brass nipple with steel nut and socket BS= Brass nipple with brass nut and steel socket
Box 9: Symbol Over All Length (OAL) Description
24 =
Expressed in inches (610 mm) OAL of a hose assembly is measured from the end of the straight fitting or centerline of the fitting seat. OAL of the Seal-Lok hose assembly is measured to the sealing surface of the straight fittings or to the centerline of the elbow fittings
06 =
Accessories
39 =
Box 5: Symbol
270
Specified only if two (2) elbow fittings are used. Starting with either end as the far end, measure angle clockwise to describe the displacement angle of the near end
08 =
Box 6:
Technical
Symbol
08 =
E
A-4
SG = Spring Guard AG = Armor Guard HG = Polyguard PG = ParKoil FS = Fire Sleeve AS = Partek Sleeving PS = Partek Sleeving Note: When spelling out an assembly part number, list entire sleeving part number
Catalog 4410 US
4 6500
10
12
16
20
24
32
40
48
CM CM4H CM4HP CM6H CM6HP CMR 421FS AX 426 BXX 451TC/ST 471TC/ST 451TC Twin Tough Hydraulic 471TC Twin Tough 436 721/721TC 721ST 781 P35 791TC 761 Suction & Return
2-braids, wire 4-spiral, wire 4-spiral, wire 6-spiral, wire 6-spiral, wire 2-braids, wire high tensile wire braid 1-braid, wire 1-braid, wire 2-braids, wire 1-braid, wire 2-braids, wire 1 braid, steel wire 2-braids, steel wire 2-braids, wire 4-spiral, wire 4-spiral, wire 4/6-spiral, wire 4/6-spiral, wire 4/6-spiral, wire 6-spiral, wire
5500 5500 5000 5000 5000 4000 4000 5000 5000 5000 5000 5000 5000 5000 1000 1000
40/+212 -40/+250 -40/+250 40/+212 40/+212 40/+180 40/+257 40/+212 625 500 375 50/+302 100R1AT 40/+212 100R2AT 40/+212 40/+212 40/+212 40/+212 55/+302 40/+257 40/+257 40/+257 5000 6000 6000 6000 6000 8000 8000 100 300 70 250 175 50 200 50 150 50 100 62 62 40/+257 40/+257 40/+257 40/+212 40/+212 40/+212 55/+302 750 400 300 300 200 50/+212 -50/+212 350 500 350 500 40/+250 -22/+257 J2064 Type C J1402 A J1402 A 100R4 100R4 100R16 100R12 100R12 100R13 100R13 100R15 3862-1-R12 856-R12 3862-1-R12 856-R12 3862-1-R13 856-R13 3862-1-R13 856-R13 3862-1-R15 100R17 100R17 11237-1-2SC 857-2SC 11237-1 11237-1-2SC 857
A-6 A-6 A-6 A-7 A-7 A-7 A-7 A-8 A-8 A-8 A-9 A-9 A-10 A-10 A-10
Coalmaster
2000
1250
3000 2500 1500 1250 1000 2250 2000 1500 1250 1000
4000 3500 2750 2250 2000 1625 1250 1125 3000 3000 3000 3000 3000 3000 5000 4250 3625 3125 2500 3000 3000 5000 4250 4000 3500 2750 2250 2000 4000 4000 4000 4000 4000 3000 2500 2500 4000 4000 4000 4000 3000 5000 5000 5000 5000
A-11 A-11 A-12 A-12 A-12 A-13 A13 A-16 A-16 A-14 A-14 A-15 A-15
811/811HT with HC 1-braid, 1-spiral wire 811/811HT with 81 1-braid, 1-spiral wire 801 836 213 1-braid, fiber 1-braid, fiber 1-braid, fiber 1-braid. fiber 1-braid, wire 1-braid, fiber 350 500 350 250 250 250 250 250 250 250 250
250
2000 1500 1500 1250 1000 225 350 500 225 350 500
Transportation
E
A-5
Hose Products Division Parker Hannifin Corporation Wickliffe, Ohio www.parkerhose.com
Technical
Accessories
Push-Lok
Equipment
A-11
Fittings
Coalmaster Hose
Hose Size
Hose Reinforcement
SAE
ISO
EN
Page
Catalog 4410 US
CM
Coalmaster Hose
Coalmaster Hose
Approvals: MSHA. Part Number CM04 CM06 CM08 Working Pressure psi MPa 6500 448 5500 379 5000 345 Minimum Bend Radius inch mm 4 102 5 127 7 178 Inner Tube: Seamless Neoprene, oil resistant. Weight lbs/ft kg/m 0.27 0,40 0.38 0,57 0.46 0,69 Coupling 43/HY 43/71/HY 43/71/HY Reinforcement: Two high tensile wire braids. Cover: Oil, weather, and flame resistant. Temperature Range: -40C to +100C (-40F to +212F).
CM4H
Fittings
Equipment
CM4HP
Four Spiral Hose - Heavy Duty
Approvals: MSHA, R.J. Budge (UK), LOBA. Part Number Hose I.D. inch mm 3/4 20 1 25 1-1/4 32 Hose O.D. inch mm 1.31 33.3 1.57 39.9 1.83 46.5 Working Pressure psi MPa 5000 345 5000 345 5000 345 Minimum Bend Radius inch mm 11.00 280 13.40 340 18.10 460 Weight lbs/ft kg/m 1.16 1,73 1.51 2,25 1.82 2,71 Coupling 71 71 71 Inner Tube: Seamless Neoprene, oil resistant. Reinforcement: Four spiralled layers of high tensile wire. Cover: Oil, weather, and flame resistant. Polyethylene abrasion resistant. Temperature Range: -40C to +100C (-40F to +250F).
Accessories
Technical
See Section C for Parkrimp Assembly Instructions. Temperature Range of other media listed in Section E. Actual hoses have embossed laylines and will look different than the illustrations.
A-6
Catalog 4410 US
CM6H
Six Spiral Hose - Heavy Duty
Approvals: MSHA, British Coal, LOBA. Part Number CM6H24 CM6H32 Hose I.D. inch mm 1-1/2 40 2 50 Hose O.D. inch mm 2.31 58.7 2.88 73.2 Working Pressure psi MPa 5000 345 5000 345 Minimum Bend Radius inch mm 20 508 25 635 Weight lbs/ft kg/m 3.42 5,10 4.76 7,10 Coupling 78/NB S6/NB Inner Tube: Seamless Neoprene, oil resistant. Reinforcement: Multiple layers of wire. Cover: Oil, weather, and flame resistant. Temperature Range: -40C to +120C (-40F to +212F).
Coalmaster Hose
CM6HP
Six Spiral Hose - Heavy Duty
Approvals: MSHA, R.J. Budge (UK), LOBA. Part Number CM6HP24 CM6HP32 Hose I.D. inch mm 1-1/2 40 2 50 Hose O.D. inch mm 2.31 58.7 2.88 73.2 Working Pressure psi MPa 5000 345 5000 345 Minimum Bend Radius inch mm 20 508 25 635 Weight lbs/ft kg/m 3.48 5,19 5.15 7,68 Coupling 78/NB S6/NB Inner Tube: Seamless Neoprene, oil resistant. Reinforcement: Multiple layers of wire. Cover: Oil, weather, and flame resistant. Polyethylene abrasion resistant cover Temperature Range: -40C to +120C (-40F to +212F).
Equipment Fittings
CMR
Coalmaster Hose
Approvals: MSHA. Part Number CMR40 CMR48 Working Pressure psi MPa 1000 69 1000 69 Minimum Bend Radius inch mm 16 406 20 508 Inner Tube: Seamless Neoprene, oil resistant. Weight lbs/ft kg/m 3.76 5,80 4.46 6,65 Coupling IE IE Reinforcement: Two high tensile wire braids. Cover: Seamless Neoprene. Temperature Range: -40C to +82C (-40F to +180F).
C
Hose O.D. inch mm 3.56 90.5 4.00 101.6
421FS
Fire Suppression Hose
Approvals: MSHA. Inner Tube: Synthetic Rubber. Part Number 421FS-4 421FS-8 421FS-12 Hose I.D. inch mm 1/4 6,3 1/2 12,5 3/4 19 Hose O.D. inch mm 0.53 13 0.81 21 1.09 28 Working Pressure psi MPa 2750 192 2000 140 1250 87 Minimum Bend Radius inch mm 4 100 7 180 9.5 240 Weight Coupling lbs/ft kg/m 0.16 0,24 43 0.29 0,43 43 0.42 0,63 43 Reinforcement: Ohio high tensile wire braid. Temperature Range: -40C to +125C (-40F to +257F).
See Section C for Parkrimp Assembly Instructions. Temperature Range of other media listed in Section E. Actual hoses have embossed laylines and will look different than the illustrations.
E
Hose Products Division Parker Hannifin Corporation Wickliffe, Ohio www.parkerhose.com
A-7
Technical
Accessories
Catalog 4410 US
AX
Hydraulic
Hydraulic Hose
Application: Petroleum base hydraulic fluids and lubricating oils. Part Number AX04 AX06 AX08 AX10 AX12 AX16 Hose I.D. inch mm 1/4 6,3 3/8 1/2 5/8 3/4 1 10 12,5 16 19 25 Hose O.D. inch mm 0.50 13 0.62 0.75 0.88 1.01 1.29 16 19 22 26 33 Working Pressure psi MPa 3000 21 3000 2500 1500 1250 1000 21 17,5 10,5 8,7 7 Minimum Bend Radius inch mm 2 50 2-1/2 3-1/2 4 4-3/4 6 65 90 100 120 150 Inner Tube: Synthetic Rubber. Weight lbs/ft kg/m 0.15 0,22 0.19 0.24 0.29 0.34 0.48 0,28 0,36 0,43 0,51 0,72 Parkrimp HY Series Reinforcement: One braid steel wire. Cover: Synthetic rubber, MSHA accepted. Temperature Range: -40F to +212F (-40C to +100C). Fittings: HY Series - pg. B-138.
426
Fittings
B
Part Number 426-4 426-6 426-8
Equipment
Hose I.D. inch mm 1/4 6,3 3/8 1/2 5/8 3/4 1 1-1/4 1-1/2 2 10 12,5 16 19 25 31,5 38 51
Hose O.D. inch mm 0.53 13 0.68 0.81 0.94 1.09 1.40 1.79 2.00 2.54 17 21 24 28 36 45 51 64
Working Pressure psi MPa 2750 19,2 2250 2000 1500 1250 1000 625 500 375 15,7 14,0 10,5 8,7 7,0 4,3 3,5 2,6
Minimum Bend Radius inch mm 4 100 5 7 8 9-1/2 12 16-1/2 20 25 125 180 200 240 300 420 500 630
BXX
Hydraulic
Accessories
Part Number BXX04 BXX06 BXX08 BXX10 BXX12 BXX16 BXX20 BXX24 BXX32
Technical
Hose I.D. inch mm 1/4 6,3 3/8 10 1/2 12,5 5/8 16 3/4 19 1 25 1-1/4 31,5 1-1/2 38 2 51
Hose O.D. inch mm 0.59 15 0.74 19 0.87 22 1.00 25 1.15 29 1.49 38 1.88 47,8 2.13 54 2.63 66,8
Working Pressure psi MPa 5000 35 4000 28 3500 24,5 2750 19,2 2250 15,7 2000 14 1625 112 1250 86 1125 78
Minimum Bend Radius inch mm 4 100 5 125 7 180 8 200 9-1/2 240 12 305 16-1/2 420 20-1/2 500 25 630
See Section C for Parkrimp Assembly Instructions. Temperature Range of other media listed in Section E. Actual hoses have embossed laylines and will look different than the illustrations.
A-8
Catalog 4410 US
451TC
Hydraulic
SAE 100R17 / ISO 11237 - 1 TYPE R17 - Constant Working Pressure
Hydraulic Hose
451ST
Hydraulic
SAE 100R17 / ISO 11237 - 1 TYPE R17 - Constant Working Pressure
Application: Petroleum base hydraulic fluids and lubricating oils. Weight lbs/ft kg/m 0.16 0,24 0.23 0.35 0.44 0.58 0.79 1.50 0,34 0,52 0,66 0,86 1,17 2,23 Parkrimp 43 Series Inner Tube: Synthetic rubber. Reinforcement: One or two braid steel wire (4-spiral for size -20). Cover: Synthetic rubber abrasion resistant, MSHA accepted.
Hose I.D. inch mm 1/4 6,3 3/8 1/2 5/8 3/4 1 1-1/4 10 12,5 16 19 25 31,5
Hose O.D. inch mm 0.52 13 0.68 0.80 0.94 1.10 1.40 1.85 17 20 24 28 35 47
Working Pressure psi MPa 3000 21,0 3000 3000 3000 3000 3000 3000 21,0 21,0 21,0 21,0 21,0 21,0
Minimum Bend Radius inch mm 2 50 2-1/2 3-1/2 4 4-3/4 6 8-1/4 65 90 100 120 150 210
471TC
Hydraulic
ISO 11237-1 TYPE 2SC / EN 857 TYPE 2SC
471ST
Hydraulic
ISO 11237-1 TYPE 2SC / EN 857 TYPE 2SC
Application: Petroleum base hydraulic fluids and lubricating oils. Parkrimp 43 Series Inner Tube: Synthetic rubber. Reinforcement: Two braids steel wire. Cover: Synthetic rubber abrasion resistant, MSHA accepted. Temperature Range: -40F to +212F (-40C to +100C). Fittings: 43 Series - pg. B-73.
Hose I.D. inch mm 1/4 6,3 3/8 1/2 5/8 3/4 1 10 12,5 16 19 25
Working Pressure psi MPa 5800 40,0 5000 4250 3625 3125 2500 35,0 29,7 25,0 21,5 17,5
Minimum Bend Radius Weight inch mm lbs/ft kg/m 2 50 0.20 0,30 2-1/2 3-1/2 4 4-3/4 6 65 90 100 120 150 0.28 0.35 0.44 0.58 0.79 0,42 0,52 0,66 0,86 1,17
See Section C for Parkrimp Assembly Instructions. Temperature Range of other media listed in Section E. Actual hoses have embossed laylines and will look different than the illustrations.
E
Hose Products Division Parker Hannifin Corporation Wickliffe, Ohio www.parkerhose.com
A-9
Technical
Accessories
Equipment
Fittings
Catalog 4410 US
Hydraulic Hose
451TC
Hydraulic
SAE 100R17 / ISO 11237 - 1 TYPE R17 - Constant Working Pressure
Application: Petroleum base hydraulic fluids and lubricating oils. Weight Parkrimp lbs/ft kg/m 43 Series 0.46 0,68 0.70 1,04 Inner Tube: Synthetic rubber. Reinforcement: One braid steel wire Cover: Synthetic rubber abrasion resistant, MSHA accepted. Temperature Range: -40F to +212F (-40C to +100C).
B
471TC
Hydraulic
ISO 11237-1 TYPE 2SC / EN 857 TYPE 2SC
Application: Petroleum base hydraulic fluids and lubricating oils. Parkrimp 43 Series Inner Tube: Synthetic rubber. Reinforcement: Two braids steel wire. Cover: Synthetic rubber abrasion resistant, MSHA accepted. Temperature Range: -40F to +212F (-40C to +100C). Fittings: 43 Series- pg. B-73.
Equipment
Fittings
Minimum Bend Radius Weight inch mm lbs/ft kg/m 2-1/2 65 0.56 0,84 3-1/2 90 0.70 1,04
Accessories
436
Hydraulic
High Temperature
Application: Petroleum base hydraulic fluids and lubricating oils.
D
Part Number 436-6 436-8 436-10
Technical
Working Minimum Hose O.D. Pressure Bend Radius inch mm psi MPa inch mm 0.68 17 4000 27,5 2-1/2 65 0.81 0.94 1.09 1.41 21 24 28 36 3500 24 2750 19 2000 13,8 3-1/2 4 6 90 100 120 150
Weight lbs/ft kg/m 0.28 0,42 0.34 0.44 0.54 0.82 0,51 0,66 0,80 1,22
Inner Tube: PKR Reinforcement: Two braids steel wire. Cover: PKR rubber, blue, MSHA accepted. Temperature Range: -55F to +302F (-48C to +150C). Fittings: 43 Series - pg. B-73. 42 Series - pg. B-153.
436-12 436-16
See Section C for Parkrimp Assembly Instructions. Temperature Range of other media listed in Section E. Actual hoses have embossed laylines and will look different than the illustrations.
A-10
Catalog 4410 US
721
Hydraulic
SAE 100R12 / ISO 3862-1 TYPE R12 / EN 856 TYPE R12
721TC
Hydraulic Tough Cover
Application: Petroleum base hydraulic fluids and lubricating oils. Part Number 721/721TC-6 721/721TC-8 721/721TC-10 721/721TC-12 721/721TC-16 Hose I.D. inch mm 3/8 10 1/2 5/8 3/4 1 12,5 16 19 25 31,5 38 51 Hose O.D. inch mm 0.80 20 0.93 1.08 1.21 1.50 1.84 2.07 2.59 24 27 31 38 46 53 66 Working Minimum Pressure Bend Radius Weight psi MPa inch mm lbs/ft kg/m 4000 28,0 2-1/2 62,5 0.40 0,60 4000 4000 4000 4000 3000 2500 2500 28,0 28,0 28,0 28,0 21,0 17,5 3-1/2 4 4-3/4 6 8-1/4 10 90 100 120 150 210 250 0.62 0.74 0.94 1.34 1.74 2.01 2.75 0,93 1,10 1,40 1,99 2,59 2,99 4,09 Inner Tube: Synthetic rubber. Parkrimp 71 Series Reinforcement: Four spiral steel wire. Cover: Synthetic rubber abrasion resistant, MSHA accepted. Temperature Range: -40F to +257F (-40C to +125C). Fittings: 71 Series - pg. B-105.
B
721ST
Hydraulic
SAE 100R12 / ISO 3862-1 TYPE R12 / EN 856 TYPE R12
Application: Petroleum base hydraulic fluids and lubricating oils. Hose I.D. inch mm 1/2 12,5 5/8 3/4 1 1-1/4 16 19 25 31,5 Hose O.D. inch mm 0.94 24 1.08 1.21 1.50 1.84 27 31 38 46 Weight lbs/ft kg/m 0.54 0,80 0.74 0.94 1.34 1.74 1,10 1,40 1,99 2,59 Parkrimp 71 Series Reinforcement: Four spiral steel wire. Cover: Synthetic rubber abrasion resistant, MSHA accepted. Temperature Range: -40F to +257F (-40C to +125C). Fittings: 71 Series - pg. B-105.
Equipment
Working Pressure psi MPa 4000 28,0 4000 4000 4000 3000 28,0 28,0 28,0 21,0
Minimum Bend Radius inch mm 3-1/2 90 4 4-3/4 6 8-1/4 100 120 150 210
Hydraulic
SAE 100R13 / ISO 3862-1 TYPE R13 / EN856 TYPE R13
Application: Petroleum base hydraulic fluids and lubricating oils. Part Number 781-12 781-16 781-20 781-24 Hose I.D. inch mm 3/4 19 1 1-1/4 1-1/2 25 31,5 38 Hose O.D. inch mm 1.26 32 1.52 1.96 2.26 39 50 57 Working Pressure psi MPa 5000 35,0 5000 5000 5000 35,0 35,0 35,0 Minimum Bend Radius inch mm 9-1/2 240 12 16-1/2 20 300 420 500 Inner Tube: Synthetic rubber. Weight lbs/ft kg/m 1.07 1,59 1.48 2.48 3.22 2,20 3,69 4,79 Parkrimp 78 Series Reinforcement: Four or six spiral steel wire. Cover: Synethetic rubber, MSHA accepted. Temperature Range: -40F to +257F (-40C to +125C). Fittings: 78 Series - pg. B-120.
See Section C for Parkrimp Assembly Instructions. Temperature Range of other media listed in Section E. Actual hoses have embossed laylines and will look different than the illustrations.
E
Hose Products Division Parker Hannifin Corporation Wickliffe, Ohio www.parkerhose.com
A-11
Technical
Accessories
781
Fittings
721/721TC-20 1-1/4
Hydraulic Hose
Catalog 4410 US
P35
Hydraulic
SAE 100R13 / ISO 3862-1 TYPE R13 / EN856 TYPE R13
Hydraulic Hose
Application: Petroleum base hydraulic fluids and lubricating oils. Part Number P35-32 Hose I.D. inch mm 2 51 Hose O.D. inch mm 2.80 71 Working Pressure psi MPa 5000 35,0 Minimum Bend Radius inch mm 25 630 Inner Tube: Synthetic rubber. Weight lbs/ft kg/m 5.03 7,48 Parkrimp S6 Series Reinforcement: Four or six spiral steel wire. Cover: Synethetic rubber, MSHA accepted. Temperature Range: -40F to +257F (-40C to +125C). Fittings: S6 Series - pg. B-121.
791TC
Fittings
Hydraulic
Tough Cover
Application: Petroleum base hydraulic fluids and lubricating oils. Weight Parkrimp lbs/ft kg/m 79 Series 1.07 1,59 1.48 2.48 3.22 2,20 3,69 4,79 Inner Tube: Synthetic rubber. Reinforcement: Four or six spiral steel wire. Cover: Synthetic rubber abrasion resistant, MSHA accepted. Temperature Range: -40F to +257F (-40C to +125C). Fittings: 79 Series - pg. B-133.
Working Pressure psi MPa 6000 42,0 6000 6000 6000 42,0 42,0 42,0
Equipment
761
Hydraulic ParMax
Application: Petroleum base hydraulic fluids and lubricating oils. Parkrimp 76 Series Inner Tube: Synthetic rubber. Reinforcement: Six spiral steel wire. Cover: Synthetic rubber. Temperature Range: -40F to +257F (-40C to +125C). Fittings: 76 Series - pg. B-118.
Accessories
Working Minimum Pressure Bend Radius Weight psi MPa inch mm lbs/ft kg/m 8000 56,0 10-1/2 260 1.56 2.32 8000 56,0 13 330 2.02 3.00
Technical
See Section C for Parkrimp Assembly Instructions. Temperature Range of other media listed in Section E. Actual hoses have embossed laylines and will look different than the illustrations.
A-12
Catalog 4410 US
811
SAE 100R4
Part Number
Minimum Vacuum Bend Radius Weight Working Pressure Rating 81/88DB 88HC inches mm inch mm psi MPa psi MPa inch mm lbs/ft kg/m of Hg kPa 19,0 1.18 30,0 300 2,1 100 0,7 2-1/2 64 0.42 0,63 25 84 Hose O.D. 1,7 1,4 1 0,7 0,4 70 50 50 50 62 0,5 0,3 0,3 0,3 0,4 3 4 5 6 7 76 102 127 152 178 0.65 0,96 0.82 1,22 1.04 1,55 1.26 1,87 1.64 2,45 25 25 25 25 25 84 84 84 84 84
Parkrimp 81 Series
1-1/4 31,8 1.77 45,0 200 1-1/2 38,1 2.05 52,0 150 2 50,8 2.50 63,6 100 62 2-1/2 63,5 3.00 76,2
Application: Petroleum base hydraulic fluids and lubricating oils. Inner Tube: Synthetic rubber. Reinforcement: Multiple layers of fiber spiral and one helical wire. Cover: Synthetic rubber. Temperature Range: -40F to +212F (-40C to +100C). Fittings: 81 Series - pg. B-177. 88 Series - pg. B-177.
Fittings
811HT
SAE 100R4
Part Number
Minimum Vacuum Working Pressure Bend Radius Weight Rating Parkrimp 81/88DB 88HC inches inch mm inch mm psi MPa psi MPa inch mm lbs/ft kg/m of Hg kPa 81 Series 3/4 19,0 1.18 30,0 300 2,1 100 0,7 2-1/2 64 0.42 0,63 28 95 Hose I.D. Hose O.D. 1 25,4 1.50 38,0 250 1,7 1,4 1 0,7 0,4 70 50 50 50 62 0,5 0,3 0,3 0,3 0,4 3 4 5 6 7 76 102 127 152 178 0.65 0,96 0.82 1,22 1.04 1,55 1.26 1,87 1.82 2,71 28 28 28 28 28 95 95 95 95 95 1-1/4 31,8 1.77 45,0 200 1-1/2 38,1 2.05 52,0 150 2 50,8 2.50 63,6 100 62 2-1/2 63,5 3,00 76,2
Application: Petroleum base hydraulic fluids and lubricating oils. Inner Tube: Synthetic rubber. Reinforcement: Multiple layers of fiber spiral and one helical wire. Cover: Synthetic rubber, MSHA accepted. Temperature Range: -50F to +257F (-46C to +125C). Fittings: 8 1 Series - pg. B-177. 88 Series - pg. B-177.
See Section C for Parkrimp Assembly Instructions. Temperature Range of other media listed in Section E. Actual hoses have embossed laylines and will look different than the illustrations.
E
Hose Products Division Parker Hannifin Corporation Wickliffe, Ohio www.parkerhose.com
A-13
Technical
Accessories
Equipment
Suction and Return Line High Temperature 1/2 SAE Minimum Bend Radius
Catalog 4410 US
213
Transportation Hose
Transportation
SAE J1402 AI / D.O.T. FMVSS 106 AI - AIR BRAKE
Application: Petroleum base hydraulic fluids and lubricating oils, diesel fuels and antifreeze solutions. Inner Tube: PKR. Reinforcement: One fiber braid and one steel braid. Cover: Fiber braid. Temperature Range: -50F to +302F (-45C to +150C). Fittings: 26 Series - pg. B-55.
Part Number
Hose I.D. inch 3/16 1/4 5/16 13/32 1/2 5/8 7/8 1-1/8 1-3/8 2-3/8
Hose O.D.
Working Pressure
Minimum Bend Radius inch 3/4 1 1-1/4 1-3/4 2-1/4 2-3/4 3-1/2 4-1/2 7-1/2 14 24 mm 20 25 30 45 55 70 90 115 190 355 610
Weight lbs/ft 0.12 0.14 0.17 0.20 0.22 0.24 0.30 0.44 0.52 0.67 1.31
mm inch mm psi MPa 5 0.49 12,5 2000 14 6,3 8 10 16 22 29 35 61 0.55 0.62 0.74 0.96 1.21 1.49 1.73 2.14 2.88 14 16 19 21 24 31 38 44 54 73 1500 10,5 1500 10,5 1250 1000 750 400 300 300 200 175 8,7 7 5,2 2,8 2,1 2,1 1,4 1,2
Vacuum Rating Parkrimp inches kg/m of Hg kPa 26 Series 0,18 28 95 0,21 0,25 0,30 0,33 0,36 0,45 0,65 0,77 1,00 1,95 28 28 28 28 28 20 20 15 11 11 95 95 95 95 95 68 68 51 37 64
12,5 0.83
Fittings
213-24 213-40
213-32 1-13/16 46
271
Transportation Air Brake Hose
SAE J1402 A / D.O.T. FMVSS 106A - AIR BRAKE
Application: Air brake systems.
Equipment
Inner Tube: Synthetic rubber. Part Number 271-6 271-8 Hose I.D. inch mm 3/8 10 1/2 12,5 Hose O.D. inch mm 0.75 19 0.88 22 Working Pressure psi MPa 225 1,6 225 1,6 Minimum Bend Radius inch mm 1-3/4 45 2 50 Weight lbs/ft kg/m 0.20 0,30 0.26 0,39 Parkrimp 25 Series Reinforcement: One or more fiber braid. Cover: Synthetic Rubber. Temperature Range: -50F to +212F (-46C to +100C). Fittings: 25 Series - pg. B-51.
Technical
Accessories
See Section C for Parkrimp Assembly Instructions. Temperature Range of other media listed in Section E. Actual hoses have embossed laylines and will look different than the illustrations.
A-14
Catalog 4410 US
SS25UL
Transportation Liquefied Petroleum Gas
Application: Liquefied petroleum gas (LPG). Part Number SS25UL-4 SS25UL-5 SS25UL-6 SS25UL-8 SS25UL-10 SS25UL-12 Hose I.D. inch mm 3/16 5 1/4 5/16 13/32 1/2 5/8 6,3 8 10 12,5 16 Hose O.D. inch mm 0.52 13,2 0.58 0.68 0.77 0.92 1.08 14,8 17,2 19,5 23,4 27,4 Working Pressure psi MPa 350 2,4 350 350 350 350 350 2,4 2,4 2,4 2,4 2,4 Minimum Bend Radius Weight inch mm lbs/ft kg/m 0.75 20 0.11 0,16 1 1-1/4 1-3/4 2-1/4 2-3/4 25 30 45 55 70 0.13 0.18 0.21 0.29 0.37 0,19 0,27 0,31 0,43 0,55 Inner Tube: Synthetic rubber. Parkrimp 26 Series Reinforcement: One fiber braid and one stainless steel wire braid. Cover: Fiber braid. Temperature Range: -40F to +250F (-40C to +121C). Fittings: 2 6 Series - pg. B-55.
Transportation Hose
UL STANDARD 21
285
Refrigerant
SAE J2064 TYPE C
Application: Refrigerant 134a. Part Number Hose I.D. inch 3/16 5/16 13/32 1/2 5/8 Working Minimum Pressure Bend Radius mm 25 40 50 65 75 Vacuum Rating inches kg/m of Hg kPa 0,14 28 95 0.18 0.25 0.27 0.34 28 28 28 28 95 95 95 95 Inner Tube: Synthetic rubber with nylon barrier. Parkrimp 26 Series Reinforcement: One fiber braid. Cover: Synthetic rubber.
Hose O.D.
8 10 16
See Section C for Parkrimp Assembly Instructions. Temperature Range of other media listed in Section E. Actual hoses have embossed laylines and will look different than the illustrations.
E
Hose Products Division Parker Hannifin Corporation Wickliffe, Ohio www.parkerhose.com
A-15
Technical
Accessories
Equipment
Fittings
Catalog 4410 US
801
Multipurpose
Available Cover Colors:
Push-Lok Hose
GRA
RED
YEL
BLU
GRN
BLK Application: Pneumatic, petroleum base hydraulic fluid, lubricating oils and antifreeze solutions. Diesel fuel - approved only when coupled with HY Series fittings. Inner Tube: Synthetic rubber. Reinforcement: One fiber braid. Cover: Synthetic rubber, MSHA accepted Temperature Range: Air: +158F (+70C) Water: +185F (+85C) Oil: -40F to 257F (-40C to +125C). Fittings: 82 Series & HY Series.
Part Number
Hose I.D. inch mm 1/4 6,3 3/8 1/2 5/8 3/4 1 10 12,5 16 19 25
Hose O.D. inch mm 0.50 12,7 0.63 15,9 0.78 19,8 0.91 23,0 1.03 26,2 1.28 32,6
Weight lbs/ft 0.09 0.11 0.18 0.19 0.24 0.37 kg/m 0,13 0,16 0,27 0,28 0,36 0,55
Parkrimp HY Series
Fittings
836
Multipurpose High Temperature
Application: Pneumatic, petroleum base hydraulic fluid, lubricating oils, diesel fuels and antifreeze solutions. Inner Tube: PKR Reinforcement: One fiber braid. Cover: Blue neoprene or PKR, MSHA accepted Temperature Range: Air: +212F (+100C) Water: +185F (+85C) Oil: -55F to +302F (-48C to +150C). Diesel fuels: -40C to 150C (-40F to 302F) with HY crimps only
Part Number
Equipment
Hose I.D. inch 1/4 3/8 1/2 5/8 3/4 mm 6,3 10 12,5 16 19
Hose O.D. inch 0.50 0.63 0.78 0.91 1.03 mm 12,7 15,9 19,8 23,0 26,2
Working Minimum Pressure Bend Radius psi MPa inch 400 2,8 2-1/2 400 400 350 300 2,8 2,8 2.4 2,1 3 4 5 6 mm 65 75 125 150 180
Weight lbs/ft kg/m 0.09 0,13 0.11 0.18 0.19 0.24 0,16 0,27 0,28 0,36
Parkrimp HY Series
Technical
Accessories
See Section C for Parkrimp Assembly Instructions. Temperature Range of other media listed in Section E. Actual hoses have embossed laylines and will look different than the illustrations.
A-16