Thank you for your trust in Mechanical Projects.

Please fill out the form with the data you have available for your project and send it to info@mechanical-projects.com along with your contact email address and phone number.

Name: Company name: Email address:

Telephone number plus country and area code: Subject:

API STANDARD 650 STORAGE TANKS

TAG N. SERVICE P.O N.

TANK DETAILS Maximum capacity, m3 (bbl): Net working capacity, m3 (bbl): Overfill protection (API-2350), m3 (bbl) or mm (in.):

PUMPING RATES In, m3/h (bbl/h): Out, m3/h (bbl/h):

Maximum operating temperature, C (F):

PRODUCT Product stored: Design specific gravity : Design metal temperature, C (F): Vapor pressure, kPa (in. Water): at C (F)

1/6

CORROSION ALLOWANCE Shell, mm (in.): Roof,mm (in.): Bottom, mm (in.): Structurals, mm (in.):

SHELL DESIGN Basic standard 650 (yes/no): Appendix A (yes/no): Appendix F (yes/no): Design pressure, kPa (lbf/in.2):

ROOF DESIGN Basic standard 650 (yes/no): Appendix G (Aluminium dome) (yes/no): Appendix C (External floating) (yes/no): Appendix H (Internal floating) (yes/no): Frangible roof joint? (yes/no):

ROOF DESIGN INFORMATION Uniform live load, kPa (lbf/ft2): Special loads (provide sketch), kPa (lbf/ft2): Insulation load, kPa (lbf/ft2): Maximum design roof temperature, C (F): Gases in the vapor space:

EARTHQUAKE DESIGN (Appendix E) Seismic zone: Zone factor (Table E-2): Roof tie rods (3.10.4.5) (yes/no): Importance Factor: Site coefficient (Table E-3):

WIND LOAD Velocity, km/h (mph): Provide intermediate wind girder (3.9.7) (yes/no):

ENVIRONMENTAL EFFECTS Maximum rainfall, mm/h (in./h): Total snow accumulation, mm/h (in./h):

2/6

SIZE RESTRICTIONS Maximum diameter, m (ft): Maximum height, m (ft):

FOUNDATION TYPE Earth (yes/no): Concrete ringwall (yes/no): Other:

MATERIAL SPECIFICATIONS Shell: Roof: Bottom: Structurals

N. of shell courses:

PLATE WIDTHS AND THICKNESSES (Including corrosion allowance), mm (in.)

1. 2. 3.

4. 5. 6.

7. 8. 9.

TANK BOTTOM Plate thickness, mm (in.): Slope, mm/m (in/ft): Lap To Butt Seams From center

Minimum width and thickness of bottom annular plates (3.5), mm (In.):

Roof-to-shell detail (Figure F-1): Intermediate wind girder? (yes/no) : Top wind girder for use as walkway? (yes/no):

ROOF TYPE Supported, self-supported or floating?: Slope or radius, mm (in.): Roof plate Thickness, mm (in.): Lap Butt Joint

3/6

PAINT Shell: Exterior? (yes/no): Surface preparation: Bottom Underside? (yes/no): Surface preparation: Structural Steel Exterior? (yes/no): Surface preparation: Interior? (yes/no): Interior? (yes/no): Interior? (yes/no):

TANK BOTTOM COATING Interior? (yes/no): Material: Application specification:

INSPECTION BY: FILMS:

Shop:

Field: Property of:

WELD EXAMINATION Radiograph: Supplementary liquid penetrant or ultrasonic:

LEAK TESTING Bottom: Roof: Shell:

MILL TEST REPORTS Required? (yes/no): Plate: Structural shapes:

Purchasers references drawings:

TANK SIZE Diameter Height Internal, m (ft): Internal, m (ft): External, m (ft): External, m (ft):

Date of Standard 650 edition/revision:

4/6

STAIRWAY STYLE Circular or straight?: Angle to horizontal (degrees): Ladder:

WALKWAY Width, mm (in.): Length, m (ft):

DRAWOFF SUMP Standard: Special:

BOLTED DOOR SHEET Required? (yes/no - Appendix A Tanks only): Raised Flush

Scaffold Hitch:

INTERNAL PIPING Swing line: Suction line: Heating coil surface area, m2 (ft2):

ROOF DRAIN Hose: Jointed: Siphon:

N. and size of shell manholes: N. and size of roof manholes:

SHELL NOZZLES Mark / Size /Service

(See figures 3-4B, 3-5, and 3-7 and tables 3-8, 3-9 and 3-10)

Flanged SGL DBL SPL A

Threaded B C D E

Orientation N=0

Height from bottom

5/6

ROOF NOZZLES, INCLUDING VENTING CONNECTIONS Mark / Size / Service Flanged Threaded

(See figures 3-14 and 3-15 and tables 3-16 and 3-17)

Reinforcement

Orientation N=0

Distance from center

Note: Sketches and/or separate sheets may be attached to cover special requirements

NOTES: Please write here

Thank you for taking the time to fill out this form. Please email this form with the rest of information that you have to info@mechanical-projects.com. We will send you a price quote as soon as possible. If you have any further questions please do not hesitate to contact us at info@mechanical-projects.com - phone: 1.281.201.0302

5/6