Professional Documents
Culture Documents
Octal Buffers (3-State) : Philips Semiconductors
Octal Buffers (3-State) : Philips Semiconductors
74F244/74F244B
Octal buffers (3-State)
Philips Semiconductors
Philips Semiconductors Product specification
FEATURES DESCRIPTION
• Octal bus interface The 74F244 is an octal buffer that is ideal for driving bus lines of
buffer memory address registers. The outputs are all capable of
• 3-State output buffer sink 64mA sinking 64mA and sourcing up to 15mA, producing very good
• 15mA source current capacitive drive characteristics. The device features two output
enables, OEa and OEb, each controlling four of the 3-State outputs.
• Guaranteed output skew less than 2.0ns (74F244B) The 74F244B is functionally equivalent to the 74F244. It has been
• Reduced ground bounce (74F244B) designed to reduce effects of ground noise. Other advantages are
noted in the features.
• Reduced ICC (74F244B)
• Reduced loading (74F244B IIL = 40µA) TYPICAL
TYPICAL SUPPLY
• Split lead frame offers increased noise immunity (74F244B) TYPE PROPAGATION
DELAY
CURRENT (TOTAL)
• Industrial temperature range available (-40°C to +85°C) for 74F244 4.0ns 53mA
74F244
74F244B 4.0ns 33mA
• 74F244 available in SSOP Type II package
ORDERING INFORMATION
ORDER CODE
COMMERCIAL RANGE INDUSTRIAL RANGE
PKG DWG #
DESCRIPTION VCC = 5V ±10%, VCC = 5V ±10%,
Tamb = 0°C to +70°C Tamb = -40°C to +85°C
20-pin plastic DIP N74F244N, N74F244BN I74F244N SOT146-1
20-pin plastic SOL N74F244D, N74F244BD I74F244D SOT163-1
20-pin plastic SSOP II N74F244DB SOT339-1
Yb0 3 18 Ya0
Ia0 Ia1 Ia2 Ia3 Ib0 Ib1 Ib2 Ib3
Ia1 4 17 Ib0
Yb2 7 14 Ya2
Ya0 Ya1 Ya2 Ya3 Yb0 Yb1 Yb2 Yb3
Ia3 8 13 Ib2
Yb3 9 12 Ya3
18 16 14 12 3 5 7 9
GND 10 11 Ib3
VCC = Pin 20
GND = Pin 10
SF00227 SF00228
SF00229
LOGIC DIAGRAM
2 18 17 3
Ia0 Ya0 Ib0 Yb0
4 16 15 5
Ia1 Ya1 Ib1 Yb1
6 14 13 7
Ia2 Ya2 Ib2 Yb2
8 12 11 9
Ia3 Ya3 Ib3 Yb3
1 19
OEa OEb
VCC = Pin 20
GND = Pin 10
SF00230
1994 Dec 5 3
Philips Semiconductors Product specification
1994 Dec 5 4
Philips Semiconductors Product specification
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
TEST LIMITS
SYMBOL PARAMETER UNIT
CONDITIONS1 MIN TYP2 MAX
VCC = MIN, IOH = -3mA ±10%VCC 2.5 V
VOH High-level output voltage VIL = MAX, ±5%VCC 2.7 3.4 V
1994 Dec 5 5
Philips Semiconductors Product specification
1994 Dec 5 6
Philips Semiconductors Product specification
AC WAVEFORMS
For all waveforms, VM = 1.5V.
Ian, Ibn
VM VM Yn, Yn VM
Yn VM VM Yn, Yn VM
SF00231 SF00232
OEn VM VM OEn VM VM
3.5V
VOH–0.3V
Yn VM Yn VM
VOL+0.3V
0V
SF00233 SF00234
Waveform 2. 3-State output enable time to high level Waveform 4. 3-State output enable time to low level
and output disable time from high level and output disable time from low level
1994 Dec 5 7
Philips Semiconductors Product specification
1994 Dec 05 8
Philips Semiconductors Product specification
SO20: plastic small outline package; 20 leads; body width 7.5 mm SOT163-1
1994 Dec 05 9
Philips Semiconductors Product specification
SSOP20: plastic shrink small outline package; 20 leads; body width 5.3 mm SOT339-1
1994 Dec 05 10
Philips Semiconductors Product specification
NOTES
1994 Dec 05 11
Philips Semiconductors Product specification
DEFINITIONS
Data Sheet Identification Product Status Definition
This data sheet contains the design target or goal specifications for product development. Specifications
Objective Specification Formative or in Design 9397-750-05103
may change in any manner without notice.
This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips
Preliminary Specification Preproduction Product Semiconductors reserves the right to make changes at any time without notice in order to improve design
and supply the best possible product.
This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes
Product Specification Full Production
at any time without notice, in order to improve design and supply the best possible product.
Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products,
including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips
Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright,
or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes
only. Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing
or modification.
Philips Semiconductors Philips Semiconductors and Philips Electronics North America Corporation
811 East Arques Avenue register eligible circuits under the Semiconductor Chip Protection Act.
P.O. Box 3409 Copyright Philips Electronics North America Corporation 1996
Sunnyvale, California 94088–3409 All rights reserved. Printed in U.S.A.
Telephone 800-234-7381
(print code) Date of release: October 28, 1991
Document order number: 9397-750-05103