Professional Documents
Culture Documents
LG 3828TSL103L - Rz20la70
LG 3828TSL103L - Rz20la70
com
e-mail:http://www.LGEservice.com/techsup.html
LCD TV
SERVICE MANUAL
CHASSIS : ML-041B
CONTENTS .............................................................................................. 2
SPECIFICATION ........................................................................................4
BLOCK DIAGRAM...................................................................................17
An isolation Transformer should always be used during the always perform an AC leakage current check on the exposed
servicing of a receiver whose chassis is not isolated from the AC metallic parts of the cabinet, such as antennas, terminals, etc., to
power line. Use a transformer of adequate power rating as this be sure the set is safe to operate without damage of electrical
protects the technician from accidents resulting in personal injury shock.
from electrical shocks.
Leakage Current Cold Check(Antenna Cold Check)
It will also protect the receiver and it's components from being With the instrument AC plug removed from AC source, connect an
damaged by accidental shorts of the circuitry that may be electrical jumper across the two AC plug prongs. Place the AC
inadvertently introduced during the service operation. switch in the on position, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
If any fuse (or Fusible Resistor) in this TV receiver is blown, each exposed metallic parts such as antenna terminals, phone
replace it with the specified. jacks, etc.
If the exposed metallic part has a return path to the chassis, the
When replacing a high wattage resistor (Oxide Metal Film Resistor, measured resistance should be between 1MΩ and 5.2MΩ.
over 1W), keep the resistor 10mm away from PCB. When the exposed metal has no return path to the chassis the
reading must be infinite.
Keep wires away from high voltage or high temperature parts. An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Adjust brightness, color, contrast controls to minimum. Leakage Current Hot Check circuit
Measure the high voltage.
The meter reading should indicate
23.5 1.5KV: 14-19 inch, 26 1.5KV: 19-21 inch, AC Volt-meter
29.0 1.5KV: 25-29 inch, 30.0 1.5KV: 32 inch
If the meter indication is out of tolerance, immediate service and
correction is required to prevent the possibility of premature
component failure.
Good Earth Ground
such as WATER PIPE,
To Instrument's CONDUIT etc.
0.15uF
exposed
METALLIC PARTS
1.5 Kohm/10W
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service unit under test.
manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES
SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as
NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or
following servicing precautions and any of the safety precautions on exposure of the assembly.
page 3 of this publication, always follow the safety precautions. 3. Use only a grounded-tip soldering iron to solder or unsolder ES
Remember: Safety First. devices.
4. Use only an anti-static type solder removal device. Some solder
General Servicing Precautions removal devices not classified as "anti-static" can generate
1. Always unplug the receiver AC power cord from the AC power electrical charges sufficient to damage ES devices.
source before; 5. Do not use freon-propelled chemicals. These can generate
a. Removing or reinstalling any component, circuit board electrical charges sufficient to damage ES devices.
module or any other receiver assembly. 6. Do not remove a replacement ES device from its protective
b. Disconnecting or reconnecting any receiver electrical plug or package until immediately before you are ready to install it.
other electrical connection. (Most replacement ES devices are packaged with leads
c. Connecting a test substitute in parallel with an electrolytic electrically shorted together by conductive foam, aluminum foil
capacitor in the receiver. or comparable conductive material).
CAUTION: A wrong part substitution or incorrect polarity 7. Immediately before removing the protective material from the
installation of electrolytic capacitors may result in an leads of a replacement ES device, touch the protective material
explosion hazard. to the chassis or circuit assembly into which the device will be
installed.
2. Test high voltage only by measuring it with an appropriate high CAUTION: Be sure no power is applied to the chassis or circuit,
voltage meter or other voltage measuring device (DVM, and observe all other safety precautions.
FETVOM, etc) equipped with a suitable high voltage probe. 8. Minimize bodily motions when handling unpackaged
Do not test high voltage by "drawing an arc". replacement ES devices. (Otherwise harmless motion such as
3. Do not spray chemicals on or near this receiver or any of its the brushing together of your clothes fabric or the lifting of your
assemblies. foot from a carpeted floor can generate static electricity
4. Unless specified otherwise in this service manual, clean sufficient to damage an ES device.)
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable General Soldering Guidelines
non-abrasive applicator; 10% (by volume) Acetone and 90% (by 1. Use a grounded-tip, low-wattage soldering iron and appropriate
volume) isopropyl alcohol (90%-99% strength) tip size and shape that will maintain tip temperature within the
CAUTION: This is a flammable mixture. range or 500 F to 600 F.
Unless specified otherwise in this service manual, lubrication of 2. Use an appropriate gauge of RMA resin-core solder composed
contacts in not required. of 60 parts tin/40 parts lead.
5. Do not defeat any plug/socket B+ voltage interlocks with which 3. Keep the soldering iron tip clean and well tinned.
receivers covered by this service manual might be equipped. 4. Thoroughly clean the surfaces to be soldered. Use a mall wire-
6. Do not apply AC power to this instrument and/or any of its bristle (0.5 inch, or 1.25cm) brush with a metal handle.
electrical assemblies unless all solid-state device heat sinks are Do not use freon-propelled spray-on cleaners.
correctly installed. 5. Use the following unsoldering technique
7. Always connect the test receiver ground lead to the receiver a. Allow the soldering iron tip to reach normal temperature.
chassis ground before connecting the test receiver positive (500 F to 600 F)
lead. b. Heat the component lead until the solder melts.
Always remove the test receiver ground lead last. c. Quickly draw the melted solder with an anti-static, suction-
8. Use with this receiver only the test fixtures specified in this type solder removal device or with solder braid.
service manual. CAUTION: Work quickly to avoid overheating the
CAUTION: Do not connect the test fixture ground strap to any circuitboard printed foil.
heat sink in this receiver. 6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature
Electrostatically Sensitive (ES) Devices (500 F to 600 F)
Some semiconductor (solid-state) devices can be damaged easily b. First, hold the soldering iron tip and solder the strand against
by static electricity. Such components commonly are called the component lead until the solder melts.
Electrostatically Sensitive (ES) Devices. Examples of typical ES c. Quickly move the soldering iron tip to the junction of the
devices are integrated circuits and some field-effect transistors and component lead and the printed circuit foil, and hold it there
semiconductor "chip" components. The following techniques only until the solder flows onto and around both the
should be used to help reduce the incidence of component component lead and the foil.
damage caused by static by static electricity. CAUTION: Work quickly to avoid overheating the circuit
1. Immediately before handling any semiconductor component or board printed foil.
semiconductor-equipped assembly, drain off any electrostatic d. Closely inspect the solder area and remove any excess or
charge on your body by touching a known earth ground. splashed solder with a small wire-bristle brush.
Alternatively, obtain and wear a commercially available
discharging wrist strap device, which should be removed to
prevent potential shock reasons prior to applying power to the
IC Remove/Replacement
Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair
which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit
circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit
should be used to remove and replace the IC. When working with board causing the foil to separate from or "lift-off" the board. The
boards using the familiar round hole, use the standard technique following guidelines and procedures should be followed whenever
as outlined in paragraphs 5 and 6 above. this condition is encountered.
Removal At IC Connections
1. Desolder and straighten each IC lead in one operation by gently To repair a defective copper pattern at IC connections use the
prying up on the lead with the soldering iron tip as the solder following procedure to install a jumper wire on the copper pattern
melts. side of the circuit board. (Use this technique only on IC
2. Draw away the melted solder with an anti-static suction-type connections).
solder removal device (or with solder braid) before removing the
IC. 1. Carefully remove the damaged copper pattern with a sharp
Replacement knife. (Remove only as much copper as absolutely necessary).
1. Carefully insert the replacement IC in the circuit board. 2. carefully scratch away the solder resist and acrylic coating (if
2. Carefully bend each IC lead against the circuit foil pad and used) from the end of the remaining copper pattern.
solder it. 3. Bend a small "U" in one end of a small gauge jumper wire and
3. Clean the soldered areas with a small wire-bristle brush. carefully crimp it around the IC pin. Solder the IC connection.
(It is not necessary to reapply acrylic coating to the areas). 4. Route the jumper wire along the path of the out-away copper
pattern and let it overlap the previously scraped end of the good
"Small-Signal" Discrete Transistor copper pattern. Solder the overlapped area and clip off any
Removal/Replacement excess jumper wire.
1. Remove the defective transistor by clipping its leads as close as
possible to the component body. At Other Connections
2. Bend into a "U" shape the end of each of three leads remaining Use the following technique to repair the defective copper pattern
on the circuit board. at connections other than IC Pins. This technique involves the
3. Bend into a "U" shape the replacement transistor leads. installation of a jumper wire on the component side of the circuit
4. Connect the replacement transistor leads to the corresponding board.
leads extending from the circuit board and crimp the "U" with
long nose pliers to insure metal to metal contact then solder 1. Remove the defective copper pattern with a sharp knife.
each connection. Remove at least 1/4 inch of copper, to ensure that a hazardous
condition will not exist if the jumper wire opens.
Power Output, Transistor Device 2. Trace along the copper pattern from both sides of the pattern
Removal/Replacement break and locate the nearest component that is directly
1. Heat and remove all solder from around the transistor leads. connected to the affected copper pattern.
2. Remove the heat sink mounting screw (if so equipped). 3. Connect insulated 20-gauge jumper wire from the lead of the
3. Carefully remove the transistor from the heat sink of the circuit nearest component on one side of the pattern break to the lead
board. of the nearest component on the other side.
4. Insert new transistor in the circuit board. Carefully crimp and solder the connections.
5. Solder each transistor lead, and clip off excess lead. CAUTION: Be sure the insulated jumper wire is dressed so the
6. Replace heat sink. it does not touch components or sharp edges.
Diode Removal/Replacement
1. Remove defective diode by clipping its leads as close as
possible to diode body.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.
Fuse and Conventional Resistor
Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.
2. Securely crimp the leads of replacement component around
notch at stake top.
3. Solder the connections.
CAUTION: Maintain original spacing between the replaced
component and adjacent components and the circuit board to
prevent excessive component temperatures.
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
1. Application range
This specification is applied to ML-041B chassis.
3.General Specification
5.Optical Character
2. Adjustment
2.1 Adjustment overview
The unit is set to automatically adjust using the
factory automation equipment. However when errors
occur, it should be adjusted manually.
2.2 Auto Gain/Offset adjustment
2.2.1 RF Mode adjustment
2.2.1.1 Adjustment preparation
Conduct Heat Run at the RF fog signals for more than
30 minutes.
2.2.1.2 Auto Gain/Offset adjustment
Press IN-START Key to convert to the adjustment
mode using the adjustment (SVC) remote controller,
and press VOL+ Key at the Auto Gain menu.
Once the adjustment is completed, press the Enter
Key to save and finish the adjustment.
SVC REMOCON
13 ADJ To enter into the adjustment mode. To adjust horizontal line and sub-brightness.
14 MPX To select the multiple sound mode (Mono, Stereo or Foreign language)
15 EXIT To release the adjustment mode
16 APC(PSM) To easily adjust the screen according to surrounding brightness
17 ASC(SSM) To easily adjust sound according to the program type
18 MULTIMIDIA To check component input Shortcut keys
19 FRONT-AV To check the front AV Shortcut keys
20 CH To move channel up/down or to select a function displayed on the screen.
21 VOL To adjust the volume or accurately control a specific function.
22 ENTER To set a specific function or complete setting.
To move the channel down in the PIP screen.
23 PIP CH-(OP1)
To use as a red key in the teletext mode
To move the channel in the PIP screen
24 PIP CH+(OP2)
To use as a green key in the teletext mode
To switch between the main and sub screens
25 PIP SWAP(OP3)
To use as a yellow key in the teletext mode
To select the input status in the PIP screen
26 PIP INPUT(OP4)
To use as a blue key in the teletext mode
To set a function that will automatically adjust screen status to match
27 EYE
the surrounding brightness so natural color can be displayed.
28 MENU To select the functions such as video, voice, function or channel.
29 IN-STOP To set the delivery condition status after manufacturing the TV set.
To halt the main screen in the normal mode, or the sub screen at the PIP screen.
30 STILL
Used as a hold key in the teletext mode (Page updating is stopped.)
Displays the teletext time in the normal mode
31 TIME
Enables to select the sub code in the teletext mode
Used as the size key in the PIP screen in the normal mode
32 SIZE
Used as the size key in the teletext mode
Used as the index key in the teletext mode (Top index will be
33 MULTI PIP
displayed if it is the top text.)
To select the position of the PIP screen in the normal mode
34 POSITION Used as the update key in the teletext mode (Text will be
displayed if the current page is updated.)
35 MODE Used as Mode in the teletext mode
36 PIP To select the simultaneous screen
37 TILT To adjust screen tilt Shortcut keys
38 0~9 To manually select the channel.
TROUBLESHOOTING
No power :[A]Process
(LED indicator off)
Pass
Pass
Check Output of
Change IC1107, IC1104
IC1107, IC104 Fail
Pass
Pass
Pass
Pass
Change inverter
Check inverter
connector or inverter
Connector or inverter Fail
Pass
Pass
Repeat
[A] Process
Pass
Pass
Re-soldering or
Check the input/ Change the defect part,
output of IC1 Fail Check X11
Pass
Re-soldering or
Check the input/ Change the defect part,
output of IC901 Fail Check X900
Pass
Pass
Pass
Re-soldering or
Check the input/output Change the defect part
of IC1 Fail Chek X11
Pass
Pass
Re-soldering or
Check the input/output Change the defect part
of IC901 Fail Check X900
Pass
Check the
input source Change source input
Fail
Pass
Re-soldering or
Check the input/output Change the defect part
of IC1 Fail Check X11
Pass
Pass
Pass
POWER
L, R AT49F
IC905
GM2221
ANALOG SIGNAL IC901
DIGITAL SIGNAL TC90A65F
SOUND INPUT SM5301BS IC800
IC500
IF +,- INPUT
SOUND OUTPUT
PC RGB M52758FP
RGB OUT IC851
SIDE_AV
VCTI
IC1 SIDE_L,R
Z1000 LA7222 IC2
AT24C16 S
IC4 A
W SIDE V
IF+,-
BLOCK DIAGRAM
SCART R,G,B
Tuner
SCART V,L,R
TU1000
COMPONENT 14066
IC202
PC L,R
L,R
AUDIO
AC IN
D-SUB PC
Y Pb Pr H/P S-VHS V
BLOCK DIAGRAM DESCRIPTION
1. Video Controller Unit & Display Data Conversion Unit
The video controller unit receives the video signals inputted through the tuner, AV port (AV1, AV2, S-Video,
component), and converts them into an analog RGB signal through the microcomputer (VCTI) combined with
the video decoder that integrates various functions in one chip.
Either the analog RGB, component YPbPr or PC RGB signal is selected by the switching IC and inputted to a
scaler (GM2221), which is sent to the LCD module after being modified to an LVDS signal through the
integrated LVDS IC.
Or, it is sent to the LCD module as a TTL output.
VCTi is the main microprocessor that handles video signal processing and sound signal processing. It also
manages the RF signals received from the tuner.
The scaler can control timing to fit into the LCD panel, and can also control the size and position of the input
signal.
8 6620K00007C
or 6620K00007A
18P_1.0MM FFC
54MM 9 6631T11017R
(RZ ONLY)
P3
8
9
P1203
2P_AC_SOCKET
500MM 750MM
SPEAKER SPEAKER
EXPLODED VIEW
16
12 3
10
13
14
11
8
15
2
5 19
17
18
4
1
20
5
22
21
7
EXPLODED VIEW PARTS LIST
2 6306V20002A LCD(LIQUID CRYSTAL DISPLAY), V201V1-T02 VGA CHIMEI TFT COLOR NON
5 6400GKTX01C SPEAKER,FULLRANGE, F1527C-6428-4 K-TONE FULL-RANGE(GENERAL) 4 OHM 7/12W 85DB OTHERS 40*70MM TRACK TYPE
6 6871TST562A PWB(PCB) ASSEMBLY,SUB, RM-20LA77 ML041B SUB TOTAL BRAND CONTROL BOARD ASSY
7 6871TST563A PWB(PCB) ASSEMBLY,SUB, RM-20LA77 ML041B SUB TOTAL BRAND IR BOARD ASSY
10 6871TPT280A PWB(PCB) ASSEMBLY,POWER, RM-20LA77 POWER TOTAL LIEN CHANG LIPS FOR CMO/AUO
11 6871TST615A PWB(PCB) ASSEMBLY,SUB, RZ-17LZ50 SUB TOTAL BRAND JACK(SCART) BOARD ASSY
- 22 -
DATE: 2004. 06.16. DATE: 2004. 06.16.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C115 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C57 0CC221CK41A 220PF 1608 50V 5% R/TP NP0
C116 0CK562CK51A 5600PF 1608 50V 10% R/TP B(Y5 C58 0CC221CK41A 220PF 1608 50V 5% R/TP NP0
C117 0CK562CK51A 5600PF 1608 50V 10% R/TP B(Y5 C74 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C118 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C83 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C12 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C85 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C125 0CK105EK56A 1UF 3216 50V 10% X7R R/TP C86 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C126 0CK105EK56A 1UF 3216 50V 10% X7R R/TP C88 0CC390CK41A 39PF 1608 50V 5% R/TP NP0
C200 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C889 0CC331CK41A 330PF 1608 50V 5% R/TP NP0
C22 0CK822CK56A 8200PF 1608 50V 10% X7R R/TP C89 0CC390CK41A 39PF 1608 50V 5% R/TP NP0
C23 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C890 0CC331CK41A 330PF 1608 50V 5% R/TP NP0
C24 0CK822CK56A 8200PF 1608 50V 10% X7R R/TP C891 0CC331CK41A 330PF 1608 50V 5% R/TP NP0
C25 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C1 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C26 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C1106 0CE477BD618 470UF KME TYPE 10V 20% FL TP
C27 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C108 0CE476VH6DC 47UF MV 25V 20% R/TP(SMD) SMD
C28 0CK334CF94A "0.33UF 1608 16V 80%,-20% F(Y5" C1102 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C29 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C1103 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C3 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C1105 0CH8476F691 47UF 16V 20% 105STD (CYL) R/T
C30 0CK334CF94A "0.33UF 1608 16V 80%,-20% F(Y5" C1109 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C31 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C111 0CE475WJ6DC 4.7UF MVK 35V 20% R/TP(SMD) S
C32 0CK334CF94A "0.33UF 1608 16V 80%,-20% F(Y5" C1118 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C33 0CK334CF94A "0.33UF 1608 16V 80%,-20% F(Y5" C112 0CE475WJ6DC 4.7UF MVK 35V 20% R/TP(SMD) S
C34 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C1124 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C35 0CK334CF94A "0.33UF 1608 16V 80%,-20% F(Y5" C1130 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C37 0CK334CF94A "0.33UF 1608 16V 80%,-20% F(Y5" C1132 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C40 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C1134 0CE227WF6DC 220UF MVK 16V 20% R/TP(SMD) S
C42 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C1135 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C45 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C1137 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C52 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C1149 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C67 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C119 0CH8106F691 10UF 16V 20% 105STD (CYL) R/T
C75 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C120 0CH8106F691 10UF 16V 20% 105STD (CYL) R/T
C800 0CK105CF94A "1UF 1608 16V 80%,-20% R/TP F(" C17 0CE475WJ6DC 4.7UF MVK 35V 20% R/TP(SMD) S
C801 0CK105CF94A "1UF 1608 16V 80%,-20% R/TP F(" C5 0CE475WJ6DC 4.7UF MVK 35V 20% R/TP(SMD) S
C802 0CK105CF94A "1UF 1608 16V 80%,-20% R/TP F(" C55 0CE475VK6DC 4.7UF MV 50V 20% R/TP(SMD) SM
C807 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C60 0CE475VK6DC 4.7UF MV 50V 20% R/TP(SMD) SM
C811 0CK105CF94A "1UF 1608 16V 80%,-20% R/TP F(" C852 0CH8476F691 47UF 16V 20% 105STD (CYL) R/T
C816 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C856 0CH8476F691 47UF 16V 20% 105STD (CYL) R/T
C82 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C859 0CH8476F691 47UF 16V 20% 105STD (CYL) R/T
C861 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C87 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C865 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R C876 0CH8106F691 10UF 16V 20% 105STD (CYL) R/T
C901 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C903 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5 DIODEs
C904 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C905 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5 D100 0DRFC00288A SS14 FAIR CHILD R/TP SMA 20-1
C906 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5 D101 0DRFC00288A SS14 FAIR CHILD R/TP SMA 20-1
C911 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R D1150 0DRGS00199A UF4001 GENERAL SEMICONDUCTOR
C912 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R D102 0DS181009AA KDS181 TP KEC SOT-23 80V 30
C913 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R D103 0DS181009AA KDS181 TP KEC SOT-23 80V 30
C914 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R D107 0DS226009AA KDS226 TP KEC SOT-23 80V 300
C915 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R ZD104 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
C916 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R ZD105 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
C918 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R ZD207 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
C919 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R ZD208 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
C921 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R ZD209 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
C922 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R ZD211 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
C961 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R ZD200 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
C121 0CC100CK41A 10PF 1608 50V 5% R/TP NP0 ZD201 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
C122 0CC100CK41A 10PF 1608 50V 5% R/TP NP0 ZD202 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
C43 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0 ZD203 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
C47 0CC220CK41A 22PF 1608 50V 5% R/TP NP0 ZD204 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
C48 0CC220CK41A 22PF 1608 50V 5% R/TP NP0 ZD205 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
C53 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0 ZD206 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
C56 0CC221CK41A 220PF 1608 50V 5% R/TP NP0 D1151 0DZ330009DF MTZJ33B TP ROHM-K DO34 0.5W 3
- 23 -
DATE: 2004. 06.16. DATE: 2004. 06.16.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
IC FET & TRANSISTOR
IC905 0IZZTSA003A ML-041B VGA PAL ATMEL 32P PLC-CMO IC1107 0TF492509AA SI4925DY TP TEMIC 30V 6.1A S
IC905 0IZZTSA005A ML-041B VGA PAL ATMEL 32P PLC-AUO Q1150 0TR322809AB KTC3228-Y(KTC2383) TP KEC TO9
IC3 0IKE702700D "KIA7027AF 3, SOT-89 TP RESET" Q1 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - -
IC200 0IMMRSG036A "M24C02-WMN6T SGS-THOMSON 8P,S" Q603 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - -
IC4 0IMCRAL006A AT24C16AN-10SI-2.7 ATMEL 8P S Q100 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - -
IC903 0IMCRAL006A AT24C16AN-10SI-2.7 ATMEL 8P S Q1000 0TR388109AA KTC3881 CHIP TP KEC - -
IC100 0IMCRMZ002A MP7720 MONOLITHIC POWER SYSTE Q101 0TR150400BA CHIP 2SA1504S(ASY) BK KEC - -
IC101 0IMCRMZ002A MP7720 MONOLITHIC POWER SYSTE Q1100 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - -
IC202 0IMO140662A "MC14066BDR2 14P,SOIC TP BILAT" Q1151 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - -
IC1 0IPRPMN003C VCT49XYF C7(NTSC+PAL) MICRONA Q12 0TR150400BA CHIP 2SA1504S(ASY) BK KEC - -
IC901 0IPRPGN015A "GM2221 GENESIS 208P,QFP TRAY" Q13 0TR150400BA CHIP 2SA1504S(ASY) BK KEC - -
IC1101 0IPMGFA061A "FAN1587AD33X FAIRCHILD 3P,DPA" Q14 0TR150400BA CHIP 2SA1504S(ASY) BK KEC - -
IC1103 0IPMGSG018D "LD1086DT18TR SGS-THOMSON 3P,D" Q15 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - -
IC1108 0IMCRKE010A KIA7812AF KEC 2P DPACK R/TP 1 Q2 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - -
IC1111 0IMCRFA015A KA7805R FAIRCHILD 2P D-PAK R/ Q3 0TR150400BA CHIP 2SA1504S(ASY) BK KEC - -
IC1105 0IPMGFA061A "FAN1587AD33X FAIRCHILD 3P,DPA" IC902 0TFVI80005A VISHAY SI4963DY R/TP SO-8 -20
IC1106 0IPMGSG018D "LD1086DT18TR SGS-THOMSON 3P,D" IC1104 0TFVI80005A VISHAY SI4963DY R/TP SO-8 -20
IC1114 0IPMGFA061A "FAN1587AD33X FAIRCHILD 3P,DPA"
IC1115 0IPMGFA061A "FAN1587AD33X FAIRCHILD 3P,DPA" RESISTORs
IC1110 0ISS780800J "KA78M08R 3P,D-PAK TP VOL. REG"
IC1113 0ISS780800J "KA78M08R 3P,D-PAK TP VOL. REG" R1004 0RH3000D622 300 1/10W 5 D.R/TP
R1010 0RH7501D622 7.5K 1/10W 5 D.R/TP
COIL & CORE & INDUCTOR R1012 0RH7502D622 75K 1/10W 5 D.R/TP
R106 0RH1500D622 150 1/10W 5 D.R/TP
L104 6140TBZ045A "38.5UH(DIP), 6A, P7.5, DR8.3X" R107 0RH1003D622 100K 1/10W 5 D.R/TP
L105 6140TBZ045A "38.5UH(DIP), 6A, P7.5, DR8.3X" R1151 0RH4700D622 470 1/10W 5 D.R/TP
L1150 150-985B DR8*11 2.4MH 0.16MM 270.5T R1153 0RH1000D622 100 1/10W 5 D.R/TP
L1100 6210TCE001G HH-1M3216-501 CERATEC 3216MM R126 0RH4701D622 4.7K 1/10W 5 D.R/TP
L1101 6210TCE001G HH-1M3216-501 CERATEC 3216MM R132 0RH1003D622 100K 1/10W 5 D.R/TP
L1103 6210TCE001A HB-1S2012-080JT CERATEC 2012M R133 0RH1003D622 100K 1/10W 5 D.R/TP
L1104 6210TCE001A HB-1S2012-080JT CERATEC 2012M R134 0RH1003D622 100K 1/10W 5 D.R/TP
L1105 6210TCE001G HH-1M3216-501 CERATEC 3216MM R135 0RH1003D622 100K 1/10W 5 D.R/TP
L1106 6210TCE001G HH-1M3216-501 CERATEC 3216MM R14 0RH4701D622 4.7K 1/10W 5 D.R/TP
L1107 6210TCE001G HH-1M3216-501 CERATEC 3216MM R140 0RH0392D622 39 1/10W 5 D.R/TP
L200 6210TCE001A HB-1S2012-080JT CERATEC 2012M R141 0RH0392D622 39 1/10W 5 D.R/TP
L201 6210TCE001A HB-1S2012-080JT CERATEC 2012M R142 0RH0392D622 39 1/10W 5 D.R/TP
L202 6210TCE001A HB-1S2012-080JT CERATEC 2012M R143 0RH0392D622 39 1/10W 5 D.R/TP
L203 6210TCE001A HB-1S2012-080JT CERATEC 2012M R144 0RH0392D622 39 1/10W 5 D.R/TP
L204 6210TCE001G HH-1M3216-501 CERATEC 3216MM R145 0RH0392D622 39 1/10W 5 D.R/TP
L853 6210TCE001G HH-1M3216-501 CERATEC 3216MM R146 0RH0392D622 39 1/10W 5 D.R/TP
L900 6210TCE001G HH-1M3216-501 CERATEC 3216MM R147 0RH0392D622 39 1/10W 5 D.R/TP
L901 6210TCE001G HH-1M3216-501 CERATEC 3216MM R201 0RH4701D622 4.7K 1/10W 5 D.R/TP
L902 6210TCE001G HH-1M3216-501 CERATEC 3216MM R204 0RH4701D622 4.7K 1/10W 5 D.R/TP
L903 6210TCE001G HH-1M3216-501 CERATEC 3216MM R211 0RH0752D622 75 1/10W 5 D.R/TP
L1102 6210TCE001G HH-1M3216-501 CERATEC 3216MM R212 0RH0752D622 75 1/10W 5 D.R/TP
L205 6210TCE001A HB-1S2012-080JT CERATEC 2012M R213 0RH0752D622 75 1/10W 5 D.R/TP
L800 6210TCE001G HH-1M3216-501 CERATEC 3216MM R214 0RH4703D622 470K 1/10W 5 D.R/TP
L906 6210TCE001G HH-1M3216-501 CERATEC 3216MM R217 0RH4703D622 470K 1/10W 5 D.R/TP
L907 6210TCE001G HH-1M3216-501 CERATEC 3216MM R57 0RH1000D622 100 1/10W 5 D.R/TP
L10 0LC1032101A 10UH 10% 3216 R/TC FI-C3216-1 R59 0RH1201D622 1.2K 1/10W 5 D.R/TP
L1001 0LC1020101A 1UH 10% 2012 R/TC FI-B2012-10 R6 0RH4702D622 47K 1/10W 5 D.R/TP
L1002 0LC1032101A 10UH 10% 3216 R/TC FI-C3216-1 R818 0RH8200D622 820 1/10W 5 D.R/TP
L15 0LC1032101A 10UH 10% 3216 R/TC FI-C3216-1 R9 0RH4701D622 4.7K 1/10W 5 D.R/TP
L2 0LC1032101A 10UH 10% 3216 R/TC FI-C3216-1 R908 0RH0822D622 82 1/10W 5 D.R/TP
L8 0LC1032101A 10UH 10% 3216 R/TC FI-C3216-1 R910 0RH0822D622 82 1/10W 5 D.R/TP
L888 0LC0233002A 3.3UH CERATECH R/TP R915 0RH3600D622 CHIP 360-J 1/10 W
L889 0LC0233002A 3.3UH CERATECH R/TP R934 0RH1000D622 100 1/10W 5 D.R/TP
L890 0LC0233002A 3.3UH CERATECH R/TP R989 0RH8200D622 820 1/10W 5 D.R/TP
R999 0RH1000D622 100 1/10W 5 D.R/TP
R136 0RH8202D622 82K 1/10W 5 D.R/TP
R137 0RH8202D622 82K 1/10W 5 D.R/TP
- 24 -
DATE: 2004. 06.16. DATE: 2004. 06.16.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C931 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D R24 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
C932 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D R240 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
C933 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D R25 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
L905 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D R28 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R1002 0RH1501D622 1.5K OHM 1 / 10 W 2012 5.00% R29 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R1011 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D R3 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TP
R1106 0RH1002D622 10K OHM 1 / 10 W 2012 5.00% D R34 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R1152 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D R4 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R12 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D R41 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R128 0RH1002D622 10K OHM 1 / 10 W 2012 5.00% D R45 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R129 0RH1002D622 10K OHM 1 / 10 W 2012 5.00% D R46 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
R13 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D R49 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R202 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D R5 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R208 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D R50 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R209 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D R51 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R210 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D R52 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R36 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D R53 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R37 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D R54 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R7 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D R55 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R817 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D R56 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R822 0RH1002D622 10K OHM 1 / 10 W 2012 5.00% D R58 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R834 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D R60 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R836 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D R62 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R837 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D R64 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R961 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D R66 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R964 0RH1002D622 10K OHM 1 / 10 W 2012 5.00% D R68 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R1 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP R69 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R10 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP R70 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R1001 0RJ0562D677 56 OHM 1/10 W 5% 1608 R/TP R72 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R1003 0RJ8200D677 820 OHM 1/10 W 5% 1608 R/TP R73 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R1005 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TP R74 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R1014 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP R75 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R11 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP R76 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R1105 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP R77 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R1107 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP R78 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R1149 0RH1002D622 10K OHM 1 / 10 W 2012 5.00% D R8 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R1150 0RJ0102D677 10 OHM 1/10 W 5% 1608 R/TP R80 0RJ2202D677 22K OHM 1/10 W 5% 1608 R/TP
R124 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP R888 0RJ0752D677 75 OHM 1/10 W 5% 1608 R/TP
R125 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP R889 0RJ0752D677 75 OHM 1/10 W 5% 1608 R/TP
R127 0RJ2701D677 2.7K OHM 1/10 W 5% 1608 R/TP R890 0RJ0752D677 75 OHM 1/10 W 5% 1608 R/TP
R130 0RJ1202D677 12K OHM 1/10 W 5% 1608 R/TP R901 0RJ0472D677 47 OHM 1/10 W 5% 1608 R/TP
R131 0RJ1202D677 12K OHM 1/10 W 5% 1608 R/TP R902 0RJ0472D677 47 OHM 1/10 W 5% 1608 R/TP
R138 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP R904 0RJ0472D677 47 OHM 1/10 W 5% 1608 R/TP
R139 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP R907 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R15 0RJ0822D677 82 OHM 1/10 W 5% 1608 R/TP R909 0RJ0822D677 82 OHM 1/10 W 5% 1608 R/TP
R16 0RJ2200D677 220 OHM 1/10 W 5% 1608 R/TP R911 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R17 0RJ0822D677 82 OHM 1/10 W 5% 1608 R/TP R912 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R18 0RJ2200D677 220 OHM 1/10 W 5% 1608 R/TP R913 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R19 0RJ0822D677 82 OHM 1/10 W 5% 1608 R/TP R914 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R2 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP R917 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R20 0RJ2200D677 220 OHM 1/10 W 5% 1608 R/TP R928 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R203 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP R929 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R205 0RJ0222D677 22 OHM 1/10 W 5% 1608 R/TP R930 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R206 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP R931 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R207 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP R932 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R21 0RJ0222D677 22 OHM 1/10 W 5% 1608 R/TP R935 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R22 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP R936 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R221 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP R938 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R224 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP R939 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R225 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP R940 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R226 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP R941 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R23 0RJ2701D677 2.7K OHM 1/10 W 5% 1608 R/TP R942 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
- 25 -
DATE: 2004. 06.16. DATE: 2004. 06.16.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
R943 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP Q2103 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - -
R944 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R945 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP JACK BOARD
R946 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R947 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP C1217 0CH3104K946 100000PF 50V Z F 2012 R/TP
R952 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP C1201 0CH6221K416 220PF 50V J NP0 2012 R/TP
R953 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP C1202 0CH6101K416 100PF 50V J NP0 2012 R/TP
R954 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP C1207 0CH6471K416 470F 50V J NP0 2012 R/TP
R96 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP C1208 0CH6471K416 470F 50V J NP0 2012 R/TP
R979 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP C1221 0CH6331K416 330PF 50V J NP0 2012 R/TP
R980 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP C1223 0CH6471K416 470F 50V J NP0 2012 R/TP
R981 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP C1224 0CH6471K416 470F 50V J NP0 2012 R/TP
R982 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP C1210 0CH6471K416 470F 50V J NP0 2012 R/TP
R983 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP C1212 0CH6471K416 470F 50V J NP0 2012 R/TP
R984 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP C1213 0CH6101K416 100PF 50V J NP0 2012 R/TP
R991 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP C1214 0CH6101K416 100PF 50V J NP0 2012 R/TP
R992 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP C1218 0CH6331K416 330PF 50V J NP0 2012 R/TP
C1219 0CH6331K416 330PF 50V J NP0 2012 R/TP
OTHERs C1220 0CH6331K416 330PF 50V J NP0 2012 R/TP
C1215 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
Z1000 6200QL3002F "X6966M EPCOS ST SIP5K, 6200QL" C1216 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
X11 6202VDT002E SX-1SMD SUNNY RADIAL 20250000 C1200 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
X900 6202VDT002B SX-1 SUNNY SC14.3MHZ +/- 30 P C1209 0CH8226F691 22UF 16V 20% 105STD (CYL) R/T
IC905 6620F00017A CCSD-32T-SM WOOYOUNG 32P PLCC C1211 0CH8226F691 22UF 16V 20% 105STD (CYL) R/T
TU1000 6700VS0003A TAEW-G051D LG INOTEK MULTI VS L1202 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1203 6210TCE001A HB-1S2012-080JT CERATEC 2012M
CONTROL BOARD L1206 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1207 6210TCE001A HB-1S2012-080JT CERATEC 2012M
R2200 0RN1101F409 1.10K 1/6W 1% TA52 L1208 6210TCE001A HB-1S2012-080JT CERATEC 2012M
R2201 0RN8200F409 820 1/6W 1% TA52 L1211 6210TCE001A HB-1S2012-080JT CERATEC 2012M
R2202 0RN5600F409 560 1/6W 1% TA52 L1213 6210TCE001A HB-1S2012-080JT CERATEC 2012M
R2203 0RN4700F409 470 1/6W 1 TA52 L1214 6210TCE001A HB-1S2012-080JT CERATEC 2012M
R2204 0RN3900F409 390 1/6W 1% TA52 L1215 6210TCE001A HB-1S2012-080JT CERATEC 2012M
R2205 0RN3300F409 330 1/6W 1% TA52 ZD1200 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
R2206 0RN2700F409 270 1/6W 1% TA52 ZD1206 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
R2207 0RN3301F409 3.30K 1/6W 1% TA52 ZD1207 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
R2208 0RN2000F409 200 1/6W 1% TA52 ZD1212 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
SW2200 140-313A TACT 2LEAD 100G(TA) LG C&D NO ZD1213 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
SW2201 140-313A TACT 2LEAD 100G(TA) LG C&D NO ZD1214 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
SW2202 140-313A TACT 2LEAD 100G(TA) LG C&D NO ZD1210 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
SW2203 140-313A TACT 2LEAD 100G(TA) LG C&D NO ZD1211 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
SW2204 140-313A TACT 2LEAD 100G(TA) LG C&D NO ZD1215 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
SW2205 140-313A TACT 2LEAD 100G(TA) LG C&D NO ZD1216 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
SW2206 140-313A TACT 2LEAD 100G(TA) LG C&D NO ZD1217 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
SW2207 140-313A TACT 2LEAD 100G(TA) LG C&D NO ZD1218 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD1219 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
L1200 0LC1020101A 1UH 10% 2012 R/TC FI-B2012-10
IR BOARD
L1212 0LC0233002A 3.3UH CERATECH R/TP
C2101 0CH3104K566 0.1UF 50V 10% X7R 2012 R/TP L1209 0LC0233002A 3.3UH CERATECH R/TP
L2101 6210TCE001A HB-1S2012-080JT CERATEC 2012M L1210 0LC0233002A 3.3UH CERATECH R/TP
LED2100 0DL200000CA SAM5670(DL-2LRG) BK Y-GREEN - JA1201 6613V00008F PMJ014F PARK ELEC E/P(ST)+S-V
PA2101 6726TV0001A TSOP4838SO1 VISHAY 38.0KHZ HO JA1200 381-091C UPJ-R1-019 UGCOM 21PIN W/SHIE
R2101 0RH1000D622 100 1/10W 5 D.R/TP R1200 0RH0682D622 68 1/10W 5 D.R/TP
R2102 0RH1000D622 100 1/10W 5 D.R/TP R1202 0RH0752D622 75 1/10W 5 D.R/TP
R2106 0RH1000D622 100 1/10W 5 D.R/TP R1206 0RH0752D622 75 1/10W 5 D.R/TP
R2111 0RH4301D622 4.3K 1/10W 5 TA R1217 0RH4703D622 470K 1/10W 5 D.R/TP
R2103 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D R1218 0RH5101D622 5.1K 1/10W 5 D.R/TP
R2104 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D R1219 0RH5101D622 5.1K 1/10W 5 D.R/TP
R2105 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D R1220 0RH4703D622 470K 1/10W 5 D.R/TP
R2113 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D R1230 0RH0752D622 75 1/10W 5 D.R/TP
Q2101 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - - R1231 0RH0752D622 75 1/10W 5 D.R/TP
Q2102 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - - R1232 0RH5101D622 5.1K 1/10W 5 D.R/TP
- 26 -
DATE: 2004. 06.16.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
- 27 -
Jun., 2004
P/NO : 3828TSL103L Printed in Korea