Professional Documents
Culture Documents
CH3510 Mechanical Operations Lab Chemical Engineering: Experiment No: 1
CH3510 Mechanical Operations Lab Chemical Engineering: Experiment No: 1
CH3510 Mechanical Operations Lab Chemical Engineering: Experiment No: 1
EXPERIMENT NO: 1
BALL MILLING
Aim:
To determine the particle size distribution and specific surface area of the given
sample (calcite) and also study the effects of grinding rate using batch ball mill.
Apparatus :
Theory :
A ball mill, a type of grinder, is a cylindrical device used in grinding (or mixing)
materials like ores, chemicals, ceramic raw materials and paints. Ball mills rotate
around a horizontal axis, partially filled with the material to be ground plus the
grinding medium. Different materials are used as media, including ceramic balls,
flint pebbles and stainless steel balls.
Principle of grinding:
The size reduction in a ball mill is purely done by the impact of balls in the
cylinder. When the mill is rotated, the balls are picked up by the mill wall and
carried nearly to the top, where they break contact with the wall and fall to the
bottom to be picked up again. Centrifugal force keeps the balls in contact with the
wall and with one another during the upward movement. Most of the grinding
occurs at the zone of impact, where the free falling balls strike the bottom of the
mill.
Experimental procedure:
1. The sieve shaker is filled with the given sample of calcite of known weight.
2. Sieve analysis should be performed for the given sample for 10 minutes
using the standard set of sieves.
3. Now, place the given calcite sample in the ball mill which is already filled
with steel balls (20mm) up to 50% of its volume.
4. The ball is should be rotated with the speed which is equal to 75% of the
critical speed which is calculate from the formula given below:
where,
Nc- critical speed (rps)
R- Radius of the ball mill(m)
r- Radius of the ball (m)
g- Gravitational constant (m/sec2 )
5. On substituting the values of g=9.8 m/sec2, R=75 mm, r = 6.872 mm in the
above equation, we will get Nc as 114.53 rpm. So, the ball mill will be operated
at a speed of 85.89 rpm.
6. After running the ball mill, operated at the power 0.08 kw/hr, for specific
time (first time run the ball mill for 2 min), place the sample on a paper and
perform sieving again for a specific time of 10 mins.
7. Now, again repeat the above procedure by placing the sample in the ball mill
for two more times (time intervals being 2 min (at t= 4 min) and 5 mins(at t= 9
min) respectively), and then perform sieve analysis.
8. The surface area of the given sample has to be calculated for each time
interval using the sieve analysis data.
9. A graph is plotted between specific surface areas with time of grinding.
Calculate the rate of grinding from the slopes of the curve.
10. Plot grinding rate with time of grinding.
200 g
Density of calcite
1.9 g/cc
0.78
150 mm
6.872 mm
85.90
I
II
II
IV
V
Pan
Total
Weight
fraction(xi)
Average
diameter
[Di] (mm)
3.15 mm
1.6 mm
630 m
315 m
90 m
<90 m
0.3681
0.5873
0.0378
5.4x10-3
8 x10-4
7 x 10-4
1
3.15
2.375
1.115
0.4725
0.2025
0.045
73.4
117.09
7.53
1.08
0.15
0.13
199.38
Xi/Di(mm-1)
0.11687
0.26394
0.03914
0.01146
0.00372
0.01449
0.4496
The total Specific surface area of the given sample calculated by using the above
data is
S = 1.547 * 0.154
= 0.238 m2/kg
Actual S = Scal S = (1.8203 0.238) m2/kg
At t = 2 min
Sieve No
I
II
II
IV
V
Pan
Total
S = 10.404 m2/kg
54.04
77.6
28.72
9.11
14.25
15.3
199.02
Weight
fraction(xi)
Average
diameter
[Di] (mm)
3.15
2.375
1.115
0.4725
0.2025
0.27153
0.38991
0.14431
0.04577
0.07160
0.07688 0.045
1
Xi/Di(mm-1)
0.08620
0.17524
0.14954
0.09688
0.32358
1.70837
1.0021
At t= 4 minutes
Sieve No
I
II
II
IV
V
Pan
Total
Weight
fraction(xi)
3.15 mm
1.6 mm
630 m
315 m
90 m
<90 m
0.2263
0.30
0.13
0.0432
0.1193
0.1812
1
44.95
59.6
25.83
8.58
23.69
36
198.65
S = 20.441 m2/kg
S/S = w {(1/w) + (1/xi)}
(1/xi) = 46.6445
S/S= 5*10-6 (5+46.6445) = 2.58x10-4
S = 20.441*2.58x10-4 = 5.278x10-3 m2/kg
Actual S = Scal S = (20.4415.278X10-3) m2 /kg
Average
diameter
[Di] (mm)
0.22628
0.30003
0.13003
0.04319
0.11925
0.18122
Xi/Di(mm-1)
0.07183
0.13484
0.13474
0.09141
0.58851
4.02718
At t= 9 minutes
Sieve No
I
II
II
IV
V
Pan
Total
34.15
37.65
15.52
4.35
28.74
77.56
197.97
Weight
fraction(xi)
0.17250
0.19018
0.07840
0.02197
0.14517
0.39178
Average
diameter
[Di] (mm)
3.25
2.375
1.117
0.4725
0.2025
0.045
Xi/Di(mm-1)
0.05476
0.08547
0.08124
0.04650
0.71691
8.70615
0 min
2 min
4 min
9 min
1.8203
10.4041
20.441
39.2349
4.2919
5.0184
3.7588
(m2/kg)
Grinding rate ds/dt
(m2/kg.min)
Graphs:
Specific surface area (S) vs. Time (t)
Surface area
10
time (min)
Here Y axis represents specific surface area in units of m2/kg and X-axis
represents time in units of minutes. It clearly shows that amount of surface
area increases monotonically as the period of milling increases. It is because
during milling size of the particle is reduced which results in increased
surface area.
Grinding rate
Here Y-axis is in m2 and X axis in minutes. Y-axis represents ds/dt and Xaxis time. The graph represents variation of ds/dt with time.
Grinding rate (m2/kg.min) vs time (min)
6
5.5
5
4.5
4
grinding rate
(m2/kg.min)
3.5
3
2.5
2
0
10
5
4.5
4.2919
4
3.7588
grindind rate
3.5
3
2.5
2
0
Here y axis is surface area(in m2) while X-axis is Grinding rate (ds/dt)(in
units of m2/min).
Cumulative Distribution
SIEVE SIZE(mm)
0
0.09
0.315
0.63
1.3
3.15
Range (mm)
0 - 0.09
0.09-0.315
0.315 - 0.63
0.63 - 1.3
1.3 - 3.15
> 3.15
T=0
T=2min
0.07%
0.14%
0.68%
4.46%
63.19%
100.00%
T=4 min
7.69%
14.85%
19.43%
33.86%
72.85%
100.00%
18.12%
30.05%
34.37%
47.37%
77.37%
100.00%
T=9 min
39.18%
53.70%
55.89%
63.73%
82.75%
100.00%
Here mass fraction are given in terms of percentage for better visual representation.
Mass fraction data obtained from experiment
Sieve Size(mm)
Di(mm)
Xi at t =0
Xi at t = 2min
Xi at t = 4min
Xi at t = 9min
3.15
3.15
0.368141238
0.27153
0.22628
0.17250
1.3
2.225
0.587270539
0.38991
0.30003
0.19018
0.63
0.965
0.037767078
0.14431
0.13003
0.07840
0.315
0.4725
0.005416792
0.04577
0.04319
0.02197
0.09
0.2025
0.000752332
0.07160
0.11925
0.14517
0.045
0.000652021
0.07688
0.18122
0.39178
pan
0.7
0.6
0.5
3.15 mm
1.6 mm
0.4
630 m
0.3
315 m
0.2
90 m
< 90 m
0.1
0
0
10
Below is the visual representation of the above table. But here mass fractions
are given in percentage and sieves are named in reverse order i.e.
Sieve 1 is pan and sieve 6 is coarsest one (3.15mm).
Series 1 refers to initial sample before milling and others named in the
appropriate order i.e series 2 refers to time t= 2min, series 3 at time = 4min
and series 4 is at t= 9min
70.00%
60.00%
50.00%
Series1
40.00%
Series2
Series3
30.00%
Series4
20.00%
10.00%
0.00%
1
2) At t = 2 minutes
45.00%
40.00%
35.00%
30.00%
25.00%
Series1
20.00%
15.00%
10.00%
5.00%
0.00%
1
3) At t = 4 minutes
35.00%
30.00%
25.00%
20.00%
Series1
15.00%
10.00%
5.00%
0.00%
1
4) At t = 9 minutes
45.00%
40.00%
35.00%
30.00%
25.00%
Series1
20.00%
15.00%
10.00%
5.00%
0.00%
1
AIM: To determine the breakage function rate for the batch ball mill using
a power law type breakage function (B) assumed in theory
DATA REQUIRED
The product size analysis data collected from batch grinding experiments at
three or four different time intervals and the starting feed size
THEORY
Size reduction can be simulated if input feed is completely specified;
depends on mass balance on a particular size class. Let N number of sieves
in a set n sieve numberu no.of screens coarser than n (i.e. above screen no.
n)
FUNCTIONS
1. Grinding rate function Snfraction of material broken in a given time
coarser than that on screen n If xn be mass fraction on screen n, then
dxn/dt = -Snxn
2. Breakage function Bn,ufraction of particles entering the nth size class
resulting from breakage of particles of uth size class
Bn,u=(Dn/Du)
where Dn = average particle diameter of particles retained on nth screen
= constant
Bn,u=Bn-1,uBn,u
Grinding function depends on Duk, where k is a constant (often k = 3)
Sn=Sn-1(Dn/Dn-1)k
Mass Balance gives the equation:
dxn/dt = -Snxn+ xuSuBn,u
3. Using Euler Newton method to solve
xn,t+1= xn,t(1-Snt) + t xu,tSuBn,u
PROCEDURE
Breakage rate function is assumed as a power function.
Average value of
Diameter(mm)
0
0.09
0.315
0.63
1.3
3.15
Dn/Dn-1
0.045
0.2025
0.4725
0.965
2.225
3.15
0.105
0.428571429
0.489637306
0.433707865
0.706349206
0.01
K = 2.5
K=2.75
k = 3.0
k =3.25
k = 3.5
2.43924E-07
1.97849E-06
0.000514714
8.8153E-10
2.52676E-10
0.09
1.04782E-05
0.00097289
0.444629453
1.3377E-06
6.73598E-07
0.315
8.71421E-05
6.68269E-05
0.00003375
2.1004E-05
1.30713E-05
0.63
0.000519448
0.000476208
0.000287508
0.0002139
0.000159132
1.3
0.00419323
0.003844178
0.003524182
0.00323082
0.002961884
3.15
0.01
0.01
0.01
0.01
0.01
Column 1
0.636392862
0.2148235
0.337564282
0.08490214
0.133411521
0.395218121
0.028219468
0.044342841
0.131361176
0.3323764
0.003993673
0.006275484
0.018590487
0.047038548
0.141521927
MATLAB CODE:
end
end
2. % function to calculate x at different intervals
[xt] = final(t)
q = length(t);
x0 = [0.3681;0.5873 ; 0.0378;0.0054 ; 8.0E-4;7.0E-4];
a = breakage()*x0;
p = length(a);
diff = zeros(p,q);
for m = 1:p;
for n = 1:q;
diff(m,n) = a(m,1)*t(1,n);
end
end
for n = 1:q
xin(:,n) = x0;
end
xt = xin + diff;
end
3. Grinding Rate function
function[s] = grinding(~)
d = [3.150000000000000;2.225;0.965;0.4725;0.2025;0.04500000000000
s(1) = 0.01;
% for 100 seconds
for m = 2:6
s(m) = s(m-1)*((d(m,1)/d(m-1,1)).^1);
end
dXi/dt
Xi at t = 0 min
Xi at t =2 min
Xi at t =4 min
Xi at t = 9 min
3.15 mm
-0.003681412
36.81%
36.37%
35.49%
33.50%
1.6 mm
8.52519E-05
58.73%
58.74%
58.76%
58.77%
630 m
0.002296062
3.78%
4.05%
4.60%
5.02%
315 m
0.00094593
0.54%
0.66%
0.88%
1.05%
90
0.000413885
0.08%
0.12%
0.22%
0.30%
0.000175332
0.07%
0.09%
0.13%
0.16%
<90
m
m
SIMULATED DATA
DATA K = 2.75
Sieve size
dXi/dt
Xi at t = 0 min
Xi at t =2 min
Xi at t =4 min
Xi at t = 9 min
3.15 mm
-0.003681412
36.81%
36.37%
35.49%
33.50%
1.6 mm
8.52519E-05
58.73%
58.74%
58.76%
58.77%
630 m
0.002296062
3.78%
4.05%
4.60%
5.02%
315 m
0.00094593
0.54%
0.66%
0.88%
1.05%
90
0.000413885
0.08%
0.12%
0.22%
0.30%
0.000175332
0.07%
0.09%
0.13%
0.16%
<90
m
m
simulated data
k=3
Sieve size
dXi/dt
Xi at t = 0 min
Xi at t =2 min
Xi at t =4 min
Xi at t = 9 min
3.15 mm
-0.003681412
36.81%
36.37%
35.49%
34.83%
1.6 mm
0.000273176
58.73%
58.76%
58.83%
58.87%
630 m
0.002239752
3.78%
4.05%
4.58%
4.99%
315 m
0.000904927
0.54%
0.65%
0.87%
1.03%
90
6.14299E-05
0.08%
0.08%
0.10%
0.11%
0.000216536
0.07%
0.09%
0.14%
0.18%
<90
m
m
SIMULATED DATA
K= 3.25
Sieve size
dXi/dt
Xi at t = 0 min
Xi at t =2 min
Xi at t =4 min
Xi at t = 9 min
3.15 mm
-0.003681412
36.81%
36.37%
35.49%
34.83%
1.6 mm
0.000445457
58.73%
58.78%
58.87%
58.97%
630 m
0.002191661
3.78%
4.04%
4.57%
4.96%
315 m
0.000868726
0.54%
0.65%
0.86%
1.01%
90
0.000379837
0.08%
0.12%
0.17%
0.28%
0.000162324
0.07%
0.08%
0.13%
0.15%
<90
m
m
dXi/dt
Xi at t = 0 min
Xi at t =2 min
Xi at t =4 min
Xi at t = 9 min
3.15 mm
-0.003681412
36.81%
36.37%
35.49%
34.83%
1.6 mm
0.000603397
58.73%
0.587805087
58.90%
59.05%
630 m
0.002138646
3.78%
0.040397071
4.56%
4.93%
315 m
0.000835707
0.54%
0.006459263
0.85%
0.99%
90
0.000365755
0.08%
0.001208136
0.17%
0.27%
0.000156078
0.07%
0.00084681
0.13%
0.15%
<90
70.00%
60.00%
50.00%
40.00%
3.15mm
1.3mm
30.00%
0.63mm
20.00%
10.00%
0.00%
0
b)
1.20%
1.00%
0.80%
0.315mm
0.60%
90micrometer
Pan
0.40%
0.20%
0.00%
0
Sn = Sn-1* (Dn/Dn-1)2.75
2) K = 2.75
a)
70.00%
60.00%
50.00%
40.00%
3.15mm
1.3mm
30.00%
0.63mm
20.00%
10.00%
0.00%
0
0.60%
sieve size 90
micrometer
0.40%
Pan
0.20%
0.00%
0
10
Sn = Sn-1* (Dn/Dn-1)3
3) K= 3
a)
70.00%
60.00%
50.00%
40.00%
3.15mm
1.3mm
30.00%
0.63mm
20.00%
10.00%
0.00%
0
b)
1.20%
1.00%
0.80%
0.315mm
0.60%
90 micrometer
Pan
0.40%
0.20%
0.00%
0
Sn = Sn-1* (Dn/Dn-1)3.25
4) K = 3.25
a)
70.00%
60.00%
50.00%
40.00%
3.15mm
1.3mm
30.00%
0.63
20.00%
10.00%
0.00%
0
b)
1.20%
1.00%
0.80%
0.315mm
0.60%
90 micrometer
Pan
0.40%
0.20%
0.00%
0
Sn = Sn-1* (Dn/Dn-1)3.5
5) K = 3.5
a)
70.00%
60.00%
50.00%
40.00%
3.15mm
1.3mm
30.00%
0.63mm
20.00%
10.00%
0.00%
0
b)
1.20%
1.00%
0.80%
0.315mm
0.60%
90 micrometer
Pan
0.40%
0.20%
0.00%
0
dx/dt
0.04828475
0.011313282
0.010755298
0.02345111
S1
0.131172916
0.041664866
0.047531477
0.073456419
Let us the average value of S1 = 0.07346 and use the same formula for calculating
other Sn values.. By substituting this value we get the following simulation results
TIME t= 0 2 min
4 min
9 min
3.15
-0.027039308
36.81%
33.57%
23.83%
9.23%
1.3
-0.000881463
58.73%
50.62%
44.41%
31.13%
0.63
0.017361066
3.78%
5.86%
10.03%
23.40%
0.315
0.007259407
0.54%
3.31%
5.16%
6.02%
0.09
0.003182949
0.08%
2.46%
6.02%
9.94%
0.001360901
0.07%
4.18%
10.56%
20.28%
Pan
For k = 2.5
70.00%
mass fraction
60.00%
50.00%
3.15mm
40.00%
1.3mm
30.00%
0.63 mm
20.00%
0.315 mm
10.00%
0.09 mm
0.00%
0
time (min)
10
pan
SIMULATED DATA
K = 2.75
Sieve size
mm
dx/dt
Time t = 0 2 min
min
4 min
9 min
3.15
-0.027039308
36.81%
33.57%
27.08%
17.47%
1.3
0.000624302
58.73%
50.20%
44.83%
40.37%
0.63
0.016864769
3.78%
5.80%
9.85%
12.88%
0.315
0.006948068
0.54%
2.38%
3.04%
4.79%
0.09
0.003045457
0.08%
3.44%
7.17%
11.72%
0.001303342
0.07%
4.61%
8.03%
12.77%
Pan
FOR K =2.75
70.00%
60.00%
3.15mm
50.00%
1.3mm
40.00%
0.63mm
30.00%
0.315mm
20.00%
0.09mm
pan
10.00%
0.00%
0
10
SIMULATED DATA
K=3
Sieve size dx/dt
mm
initial
t = 2min
t = 4min
t = 9min
3.15
36.81%
0.027039308
33.57%
27.08%
22.21%
1.3
0.002004726 58.73%
42.77%
35.39%
24.81%
0.63
0.016451137 3.78%
5.75%
9.70%
12.65%
0.315
0.006646877 0.54%
7.34%
9.33%
9.13%
0.09
0.002516892 0.08%
4.38%
5.97%
11.43%
0.001299153 0.07%
6.20%
12.53%
19.77%
Pan
For K= 3.0
70.00%
mass fraction
60.00%
50.00%
3.15mm
40.00%
1.3mm
30.00%
0.63 mm
20.00%
0.315 mm
10.00%
0.09 mm
pan
0.00%
0.00
2.00
4.00
6.00
time (min)
8.00
10.00
SIMULATED DATA
K= 3.25
Sieve
mm
size dx/dt
initial
t = 2min
t = 4min
t = 9min
3.15
36.81%
0.027039308
33.57%
27.08%
24.21%
1.3
0.00327024
52.76%
49.26%
32.26%
0.63
0.016097879 3.78%
7.73%
9.61%
11.45%
0.315
0.006380955 0.54%
1.31%
2.87%
3.99%
0.09
0.002789972 0.08%
2.46%
3.62%
6.44%
0.00119329
1.74%
7.50%
21.24%
58.73%
0.07%
Pan
For k = 3.25
70.00%
60.00%
Mass Fraction
50.00%
3.15mm
40.00%
1.3mm
30.00%
0.63 mm
0.315 mm
20.00%
0.09 mm
10.00%
pan
0.00%
0.00
2.00
4.00
6.00
time (min)
8.00
10.00
dx/dt
3.15
-0.027039308
36.81%
33.57%
27.08%
22.21%
1.3
0.004430411
58.73%
53.80%
48.03%
42.12%
0.63
0.015708448
3.78%
5.71%
9.56%
14.60%
0.315
0.006138414
0.54%
1.31%
3.81%
4.86%
0.09
0.002686536
0.08%
3.41%
5.02%
7.53%
0.001147412
0.07%
2.21%
6.50%
8.68%
Pan
For k= 3.5
70.00%
60.00%
3.15mm
50.00%
1.3mm
40.00%
0.63mm
30.00%
0.315mm
20.00%
0.09mm
pan
10.00%
0.00%
0
10
Conclusion
The values obtained from simulation is comparable to experimental
values atleast in terms of general trends.
By comparing values obtained for different values of k we can conclude
that for k=3 simulated and experimental values are highly comparable.
So we can conclude that K =3 is the best possible value among the given
set of values.
Sources of Error:
There might be loss in the amount of sample as we keep transferring sample
from and to ball mill for different intervals of time.
Even we use the digital weighing machine for measuring different samples
at different intervals of time and also Di is also assumed exact due to which
there is an inherent error.
As particles gets finer and finer, during sieve analysis particles get struck in
the pores, due to which proper screening is not possible.