Professional Documents
Culture Documents
Bomba Vicker Triple 2520vqsv10s21a1155
Bomba Vicker Triple 2520vqsv10s21a1155
Vickers
Vane Pumps
Released 080195
M2492S
USgpm 1 2 3 4 5 6 7
dRotor
317681 351247 357286
dVane Kit
923499 923500 923501
(12 vanes)
dRing
317674 317675 317676 317677 317678 355641 331813
dCartridge
923471 923470 923496 923469 923468 923497 923498
Kit
V10P Cover Option (See Table) Bolt (4 Reqd) (See Table) Torque 4161 N.m. (3545 lb. ft.) 2706 Seat 82800 Poppet z Spring (See Table) 941038 Shim Kit Y 396095 O Ring 309199 Plug
Code V10S Cover V10F Cover V10P Cover P 372863 379543 R 372864 S 372865 Y 377829 T 372851 K 388262 586582 O Ring
V10S Cover Option (See Table) Bolt (4 Reqd) (See Table) Torque 4161 N.m. (3545 lb. ft.)
374865 Plug
Y
155023 Ring
Y
590019 O Ring
374865 Plug Bolt (4 Reqd) (See Table) Torque 4161 N.m. (3545 lb. ft.)
Code A B C D E F G H J K
Pressure setting V10P/V10F 250 psi 500 psi 750 psi 1000 psi 1250 psi 1500 psi 1750 psi 2000 psi 2250 psi 2500 psi
x V10F control valve S/A 229613 233018 232794 232795 232796 232797 232798 232799 233019 233020
38523 Bolt (4 Reqd) Torque 88102 N.m. (6575 lb. ft.) Inlet Cover (See Table) Z H 923955 Flex Side Plate Kit H Rotor (See Table) Z H 923955 Flex Side Plate Kit H 577010 Outlet Plate
Y
H 586589 O Ring H 586583 O Ring H 588506 B.U. Ring H 416426 Screw (2 Reqd) Torque 23 N.m. (2535 lb. in.) H 422206 Pin (2 Reqd) H Inlet Plate (See Table) ZY H433762 Seal Pack (4 Reqd) H Ring (See Table) H Vane Kit (See Table) (Includes 10 Vanes & inserts) Z YH 433762 Seal Pack (4 Reqd) Rear Mounting Cover (See Table)
SAE rated capacity (**20 VQ center cartridge) H USgpm 5 8 9 11 12 14 H Ring 333624 333625 374799 333626 353901 353902 H Inlet Plate 419502 419501 H Rotor 402690 403539 H Vane Kit 922741 922745 H F3 Cart. Kit 574918 574920 574921 574922 574923 574924
D H d
Included in 25** VQ shaft end cartridge kit. Included in **20 VQ center cartridge kit. Included in V10 cover end cartridge kit. Y Included in seal kit 920166. (Kit contains F3 components & both shaft seals.) Z Included in flex side plate kit; bronze face of plate must be installed toward the rotor. Kit also contains four seal packs. V Assemble seal with spring loaded sealing member towards bearing. Seals to be completely wetted with oil prior to assembly. : Install 419673 & 419672 sealing ring into body, then install cartridge kit.
Y V 429286
D 586590 O Ring
D 419079 Outlet Plate ZY D 433764 Seal Pack (4 Reqd) Z D923956 Flex Side Plate Kit DRing (See Table) D270597 Rotor Z D923956 Flex Side Plate Kit g Body Kit (See Table)
Y
Z Y D 433764 Seal Pack (4 Reqd) D430805 Inlet Plate D422207 Pin (2 Reqd) D413834 Screw (2 Reqd) Torque 45 N.m. (4050 lb.in.)
cartridge) DUSgpm 10 12 14 16 17 19 21
DF3 Cart. Kit 02125589 421570 421571 578174 421572 421573 421574
7 Port connections
g NOTE: Body kit includes body, ball, and plug. (Ball and plug not shown)
Model Code
6 7
8 9 10
11 12 13 14 15 16 17
18
19
Special seals
S .75016 Str. thd. P 1/2 NPT thd. Y .87514 Str. thd. R 1.06212 Str. thd.
15
Port orientation (Outlet #3 or primary outlet) (Viewed from cover end of pump; refer to table on next page)
V10F flow/relief control cover Code Outlet # 3 Tank port .75016 Str. thd. 1/ NPT thd. 2
16
Controlled flow rate, V10F & V10P (Omit for standard cover) Code 6 6 USgpm 7 7 USgpm 8 8 USgpm
S Standard cover F Flow control and relief cover P Priority valve and relief cover
V10F & V10P (Omit for standard cover) .5625 18 Code A 250 psi B 500 psi C 750 psi D 1000 psi E 1250 psi Code F 1500 psi G 1750 psi H 2000 psi J 2250 psi K 2500 psi
10
SAE rated capacity (V10 cover end cartridge) Code 5 5 USgpm 6 6 USgpm 7 7 USgpm
19 Rotation 11
Shaft seal
SAE rated capacity (VQ center cartridge) Code 11 11 USgpm 12 12 USgpm 14 14 USgpm
12
Shaft type
13 Outlet #1
14 Outlet #2
(at C position)
15 Outlet #3
13
14
Inlet
13 Outlet #1
(at C position)
A A B B C C D D
NOTE
V10 cover can be assembled in any of four positions refer to drawing M2005S.
NOTE
LH RH LH RH
RH
LH
To reverse cartridge kit rotation, remove the two screws and reverse the location of the inlet support plate and the outlet support plate. Reinstall the two screws hand tight. Use pump cover to align all sections of the cartridge. Carefully remove the cover and tighten the screws. When ordering spare cartridge parts, it is recommended they be obtained in cartridge kits. Kits are assembled and tested for either right or left hand rotation. If left hand rotation is required, it should be specified on parts order by adding suffix L to cartridge kit number.
RH
LH
NOTE
Standard right hand shaft rotation cartridges shown. Reverse for left hand rotation.
Printed in U.S.A.