Professional Documents
Culture Documents
01 General Information
01 General Information
General Information
FUNDAMENTAL PROCEDURES
SYMBOLS Symbol Meaning Type
Apply oil
Only ATF
Apply grease
Appropriate grease
Apply sealant
Appropriate sealant
PROTECTION OF VEHICLE
REMOVAL OF PARTS
DISASSEMBLY
INSPECTION OF PARTS
ARRANGEMENT OF PARTS
REASSEMBLY
a. b. c. d. e. f. Oil seals O-rings Cotter pins Gaskets Lock washers Nylon nuts
DEPENDING ON LOCATION:
1. Sealant should be applied or new gaskets installed. 2. Oil should be applied to the moving components of parts. 3. Specified oil or grease should be applied at the appropriate locations (such as oil seals) before reassembly.
ADJUSTMENTS
When checking the engine control module (ECM), never use a bulb exceeding 3.4W.
Do not connect a jumper wire from the power source line to a body ground. Such a connection may cause damage to harnesses or electronic components.
VOLTMETER
OHMMETER
Do not attempt to connect the ohmmeter to any circuit in which voltage is applied. Such a connection may damage the ohmmeter.
ELECTRICAL PARTS
<REMOVAL OF CONNECTOR> 1. Never pull on the wiring harness when disconnecting connectors.
Listen for a click when locking connectors. This sound indicates that they are securely locked.
1. When a tester is used to check for continuity or to measure voltage, insert tester probe from wire harness side.
2. Check terminals of waterproof connectors from connector side because they cannot be accessed from harness side.
a. Use a fine wire to prevent damage to the terminal. b. Do not damage the terminal when inserting the tester lead.
Pull lightly on individual wires to ensure that they are secured in the terminal.
REPLACEMENT OF TERMINALS
<FEMALE>
<MALE>
Color Black Brown Green Gray Blue Light blue Light green
VEHICLE LIFT (2-SUPPORT TYPE) AND SAFETY STAND POSITIONS <FRONT END>
a. Side sills (both sides)
<REAR END>
a. Side sills (both sides)
Rear end
Jack position: At the center fo the rear crossmember
TOWING
VIN LOCATIONS
1-3 4-5 6-7 8 9 10 11 12 - 17 VIN SYSTEM (MIDDLE EAST) Vehicle Gasoline 1.8L MT Gasoline 1.8L AT 1 K K 2 N N 3 A A 4 F F 5 C C 6 5 5 7 2 2 8 3 3
World Manufacturer's Identification KNA = Kia Motors corporation Vehicle Type FC = Kia CARENS Body Type 52 = 4 door wagon Engine Type 3 = Gasoline 1.8L Transmission Type 1 = 5 speed manual, 3 = 4 speed automatic Model Year 2 = 2002 Plant Location 5 = Hwasung Plant Sequential Number
10 2 2
11 5 5
12 X X
13 X X
14 X X
15 X X
16 X X
17 X X
World Manufacturer's Identification KNA = Kia Motors Corporation Vehicle Type FC = Kia CARENS Body Type 52 = 4 door Wagon Engine Type 3 = Gasoline 1.8L Check Digit
10
11
12
13
14
15
16
17
"-" symbol according to No.3.1.2 sentence 4 of 76/114/EEC World Manufacturer's Identification KNE = Kia Motors Corporation Vehicle Type FC = Kia CARENS Body Type 52 = 4 door Wargon Engine Type 3 = 1.8L DOHC Gasoline, 4 = 2.0L Deisel, 5 = 1.6L DOHC Gasoline Transmission type 1 = 5 speed manual, 3 = automatic Model Year or Dummy "0" 2 = 2002 Plant location 5 = Hwasung Plant Sequential Number
9 10 11 12 - 17
* We do not use the letters "I", "O", "Q" in Vehicle Identificatin Number
UNITS
ABBREVIATIONS
MAINTENANCE SCHEDULE