Professional Documents
Culture Documents
Panasonic CT - 20G7DF Chasis DP391
Panasonic CT - 20G7DF Chasis DP391
MTNC021096A1 B1
Service Manual
Color Television
d e i f i pl m i S
Chassis
DP391 EP391 DP391
Important notice:
Since -1 and non dash models have different PCB layouts and parts; When servicing any of these models please confirm the model number before starting service so the correct manual is used.
This supplement service manual is issued to ADD the models of the NA7DM family listed above to the simplified service manual order No. MTNC020515A1 (CT-20D12F). Included in this supplement service manual are unique characteristics and a complete parts list. Please file and use this simplified service manual together with the simplified service manual order No. MTNC020515A1 (CT-20D12F) and the main service manual order No. MTNC010305C1 (CT-32D11E).
WARNING! This Service Manual is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product or products dealt with in this Service Manual by anyone else could result in serious injury or death.
The service technician is required to read and follow the safety precautions and important safety notice in this main manual. Copyright 2002 by Matsushita Electric Corporation of America. All rights reserved. Unauthorized copying and distribution is a violation of law.
Safety precautions
General guidelines
An Isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver from being damaged by accidental shorting that may occur during servicing. When servicing, observe the original lead dress, especially in the high voltage circuit. Replace all damaged parts (also parts that show signs of overheating.) Always replace protective devices, such as fishpaper, isolation resistors and capacitors, and shields after servicing the receiver. Use only manufacturers recommended rating for fuses, circuits breakers, etc. High potentials are present when this receiver is operating. Operation of the receiver without the rear cover introduces danger for electrical shock. Servicing should not be performed by anyone who is not thoroughly familiar with the necessary precautions when servicing high-voltage equipment. Extreme care should be practiced when handling the picture tube. Rough handling may cause it to implode due to atmospheric pressure. (14.7 lbs per sq. in.). Do not nick or scratch the glass or subject it to any undue pressure. When handling, use safety goggles and heavy gloves for protection. Discharge the picture tube by shorting the anode to chassis ground (not to the cabinet or to other mounting hardware). When discharging connect cold ground (i.e. dag ground lead) to the anode with a well insulated wire or use a grounding probe. Avoid prolonged exposure at close range to unshielded areas of the picture tube to prevent exposure to x-ray radiation. The test picture tube used for servicing the chassis at the bench should incorporate safety glass and magnetic shielding. The safety glass provide shielding for the tube viewing area against x-ray radiation as well as implosion. The magnetic shield limits the x-ray radiation around the bell of the picture tube in addition to the restricting magnetic effects. When using a picture tube test jig for service, ensure that the jig is capable of handling 35kV without causing x-ray radiation. Before returning a serviced receiver to the owner, the service technician must thoroughly test the unit to ensure that is completely safe to operate. Do not use a line isolation transformer when testing. If the exposed metallic part has a return path to the chassis, the reading should be between 240k and 5.2M. If the exposed metallic part does not have a return path to the chassis, the reading should be infinite.
0.15F
TO INSTRUMENTS EXPOSED METAL PARTS
X-ray radiation
WARNING: The potential source of x-ray radiation in the TV set are the high voltage section and the picture tube. Refer to x-ray protecton circuit check in service notes in this manual to confirm HHS voltage.
Important safety notice . . . . . . . . . . . . . . . . . . . 2 Safety precautions . . . . . . . . . . . . . . . . . General guidelines . . . . . . . . . . . . . . . . . Leakage current cold check . . . . . . . . . . Leakage current hot check . . . . . . . . . . . X-ray radiation. . . . . . . . . . . . . . . . . . . . . High voltage (CRT anode) . . . . . . . . . . . Service notes . . . . . . . . . . . . . . . . . . . . . . . . . . . Leadless chip component (surface mount) . . . . . . . . . . . . . . . . Component removal . . . . . . . . . . . . . . . . Chip component Installation . . . . . . . . . . How to replace Flat-IC . . . . . . . . . . . . . . X-ray protection circuit check . . . . . . . . . 2 2 2 2 2 2 4 4 4 4 4 5
Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Foldouts notes . . . . . . . . . . . . . . . . . . . . . . . . . 14 A-Board TNP2AH048DR . . . . . . . . . . . . . . . . . 16 C-Board TNP2AA124AF. . . . . . . . . . . . . . . . . . 21 A-Board TNP2AH048DS. . . . . . . . . . . . . . . . . . 22 A & C-PCB Board . . . . . . . . . . . . . . . . . . . . . . . 28
-3-
Service notes
Note: These components are affixed with glue. Be careful not to break or damage any foil under the component or at the pins of the ICs when removing. Usually applying heat to the component for a short time while twisting with tweezers will break the component loose.
2. Using the soldering Iron and the long nose pliers, remove the IC pins that still attached to the board.
Cautin
Component removal
1. Use solder wick to remove solder from component end caps or terminal. 2. Without pulling up, carefully twist the component with tweezers to break the adhesive. 3. Do not reuse removed leadless or chip components since they are subject to stress fracture during removal.
3. Using the de-solder braid and the soldering iron, remove the solder from the board soldering pads.
malla para desoldar cautin Iron
4. Position the new Flat-IC in place (apply the pins of the Flat-IC to the soldering pads where the pins need to be soldered). Properly determine the positions of the soldering pads and pins by correctly aligning the polarity symbol. Start aligning and soldering pin no.1, then align and solder the pin in the apposite corner of the IC, this will help to align the rest of the pins.
Muesca 2do punto 1er punto
GRADE
CAPS
5. Solder all pins to the soldering pads using a fine tipped soldering iron.
CAPACITOR 1ST DIGIT 2ND DIGIT MULTIPLIER =1600 = 1.6k
b e
Soldadura
ANODES MH DIODE
SOLDER CAPS
RESISTOR
6. Check with a magnifier for solder bridge between the pins or for dry joint between pins and soldering pads. To remove a solder bridge, use a de-solder braid as shown in the figure below.
Malla Puente (en corto) Cautin
-4-
5. Exit service mode and turn receiver OFF. 6. Connect a jumper from TPD16 to TPD17. 7. Connect the diode jumper, cathode to TPD14 (cold GND), anode to TPD15 (hot GND). Note: Refer to Fig. 2 for test point location. 8. Apply 75V AC to the AC input of the Insulator transformer.Turn receiver ON. 9. Set PICTURE and BRIGTHNESS to minimum. 10. Increase the AC voltage at the input of Insulator transformer and confirm the HHS voltage is 32.0kV, at the point set starts to loose sync, 11. Reset picture controls to original levels. 12. Turn the set OFF, and remove all jumpers and connections from chassis.
-5-
Specifications are subject to change without notice or obligation. Dimensions and weights are approximate.
-6-
Boards designation
MODELS CT-2017F-1 CT-20G7DF-1 BOARD A-Board C-Board PART NUMBER TNP2AH048DR TNP2AA124AF BOARD DESCRIPTION MAIN BOARD CRT BOARD
Boards designation
MODELS BOARD A-Board CT-20D12DF-1 C-Board TNP2AA124AF CRT BOARD Table 2: Boards designation PART NUMBER TNP2AH048DS BOARD DESCRIPTION MAIN BOARD
*Note: When ordering a board, add and S after the board suffix application. Example, If order A-Board for CT-2017F-1, should be ordered as: TNP2AH048DRS.
Important notice:
Since -1 and non dash models have different PCB layouts and parts; When servicing any of these models please confirm the model number before starting service so the correct manual is used.
-7-
CAPACITORS
C001 C002 C003 C004 C005 C008 C009 C010 C011 C015 C016 C017 C018 C020 C022 C023 C024 C025 C026 C027 C028 C029 C031 C032 C033 C034 C035 C036 C037 C038 C040 C041 C042 C043 C044 C045 C046 C047 C048 C050 C051 TCJ2VB1H103K TCJ2VB1H471K ECA1HM4R7B TCJ2VC1H150J TCJ2VC1H150J TCJ2VF1H104Z ECA1AM470B TCJ2VF1H104Z ECA1AM101B ECJ2VB1C224K TCJ2VC1H101J TCJ2VB1C104K TCJ2VC1H151J TCJ2VB1C104K TCJ2VC1H101J TCJ2VC1H151J ECA1AM470B TCJ2VB1C104K TCJ2VB1C104K TCJ2VC1H391J TCJ2VB1C104K ECQB1H333JF3 ECA1HMR22B ECA1AM470B TCJ2VC1H390J TCJ2VB1H103K ECA1HM010B TCJ2VB1H103K ECA1HM0R1B ECA1AM470B ECA1AM470B ECA1HM2R2B TCJ2VF1H104Z ECA1AM470B TCJ2VC1H471J ECA1HM0R1B TCJ2VB1C104K TCJ2VC1H220J TCJ2VC1H220J ECA1AM101B TCJ2VF1H104Z TCJ2VB1H103K TCJ2VC1H560J TCJ2VC1H471J ECA0JM331B TCJ2VB1H103K ECA0JM101B ECA1CM101B Parts List CAP,C .01UF-K-50V CAP,C 470PF-K-50V CAP,E 4.7UF-50V CAP,C 15PF-J-50V CAP,C 15PF-J-50V CAP,C .1UF-Z-50V CAP,E 47UF-10V CAP,C .1UF-Z-50V CAP,E 100UF-10V CAP,C .22UF-K-16V CAP,C 100PF-J-50V CAP,C .1UF-K-16V CAP,C 150PF-J-50V CAP,C .1UF-K-16V CAP,C 100PF-J-50V CAP,C 150PF-J-50V CAP,E 47UF-10V CAP,C .1UF-K-16V CAP,C .1UF-K-16V CAP,C 390PF-J-50V CAP,C .1UF-K-16V CAP,P .033UF-J-50V CAP,E .22UF-50V CAP,E 47UF-10V CAP,C 39PF-J-50V CAP,C .01UF-K-50V CAP,E 1UF-50V CAP,C .01UF-K-50V CAP,E 0.1UF/50V CAP,E 47UF-10V CAP,E 47UF-10V CAP,E 2.2UF-50V CAP,C .1UF-Z-50V CAP,E 47UF-10V CAP,C 470PF-J-50V CAP,E 0.1UF/50V CAP,C .1UF-K-16V CAP,C 22PF-J-50V CAP,C 22PF-J-50V CAP,E 100UF-10V CAP,C .1UF-Z-50V CAP,C .01UF-K-50V CT-20D12DF-1 CAP,C 56PF-J-50V CAP,C 470PF-J-50V CT-20D12DF-1 CAP,E 330UF-6.3V CAP,C .01UF-K-50V CAP,E 100UF-6.3V CAP,E 100UF/16V
PARTS LIST
-8-
302-02
DIODES
DIODE DIODE, ZENER DIODE, ZENER DIODE, ZENER DIODE, ZENER DIODE, RECTIFIER DIODE, ZENER DIODE DIODE DIODE, ZENER DIODE, ZENER DIODE DIODE, FAST RECOVERY DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE PTC 5-OHM DIODE DIODE DIODE DIODE DIODE, ZENER DIODE DIODE, ZENER DIODE DIODE DIODE, FAST RECOVERY DIODE, ZENER CT-20D12DF-1 DIODE, ZENER CT-20D12DF-1 DIODE, ZENER CT-20D12DF-1 DIODE, ZENER CT-20D12DF-1 DIODE, ZENER DIODE Parts List
302-02
-9-
PARTS LIST
FUSES
FUSE 6.3A 125V MPU/VCJ EEPROM IR RECEIVER VOLTAGE REGULATOR, 3.3V RESET V OUT VOLTAGE REGULATOR 9V CT-20D12DF-1 VOLTAGE REGULATOR 9V CT-20G7DF-1, CT-2017F-1 VOLTAGE REGULATOR PLUS 5V AVR VOLTAGE REGULATOR PLUS 5V AVR POWER SUPPLY, 360V MTS, S-AGC AUDIO AMP AUDIO AMP AUDIO AMP AUDIO AMP
INTEGRATED CIRCUITS
TRANSISTORS
TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
COILS
FERRITE BEAD COIL, 6.8UH COIL, 6.8UH FERRITE BEAD FERRITE BEAD FERRITE BEAD COIL, PEAKING 47UH FERRITE BEAD COIL, PEAKING 33UH COIL, PEAKING 33UH FERRITE BEAD COIL, PEAKING 18UH
PARTS LIST
- 10 -
302-02
RELAYS
RL801 R001 R003 R004 R006 R007 R008 R009 R010 R011 R012 R013 R014 R015 R016 R017 R018 R019 R021 R022 R023 R024 R028 R029 R032 R033 R034 R035 R036 R037 R038 R039 R040 R041 R042 R043 R044 R044 R045 R046 R077 R078 R081 R090 R091 K6B1AGA00042 ERJ6GEYJ102V ERJ6GEYJ105V ERJ6GEYJ562V ERDS2TJ101T ERJ6GEYJ471V ERJ6GEYJ471V ERJ6GEYJ472V ERJ6GEYJ682V ERJ6GEYJ682V ERJ6GEYJ473V ERJ6GEYJ202V ERJ6GEYJ221V ERJ6GEYJ221V ERJ6GEYJ221V ERJ6GEYJ681V ERJ6GEYJ681V ERJ6GEYJ681V ERJ6GEYJ101V ERJ6GEYJ101V ERJ6GEYJ102V ERJ6GEYJ153V ERJ6GEYJ472V ERJ6GEYJ472V ERJ6ENF1002V ERJ6GEYJ222V ERJ6GEYJ222V ERJ6GEYJ332V ERJ6GEYJ562V ERJ6GEYJ103V ERJ6GEYJ223V ERJ6GEYJ102V ERJ6GEYJ223V ERJ6GEYJ153V ERJ6GEYJ392V ERJ6GEYJ103V ERJ6GEYJ103V ERJ6GEYJ332V ERJ6GEYJ101V ERJ6GEYJ102V ERJ6GEYJ103V ERJ6GEYJ103V ERJ6GEYJ103V ERJ6GEYJ471V ERJ6GEYJ185V RELAY
RESISTORS
RES,M 1K-J-1/10W RES,M 1M-J-1/10W RES,M 5.6K-J-1/10W RES,C 100-J-1/4W RES,M 470-J-1/10W RES,M 470-J-1/10W RES,M 4.7K-J-1/10W RES,M 6.8K-J-1/10W RES,M 6.8K-J-1/10W RES,M 47K-J-1/10W RES,M 2K-J-1/10W RES,M 220-J-1/10W RES,M 220-J-1/10W RES,M 220-J-1/10W RES,M 680-J-1/10W RES,M 680-J-1/10W RES,M 680-J-1/10W RES,M 100-J-1/10W RES,M 100-J-1/10W RES,M 1K-J-1/10W RES,M 15K-J-1/10W RES,M 4.7K-J-1/10W RES,M 4.7K-J-1/10W RES,M 10K-F-1/10W RES,M 2.2K-J-1/10W RES,M 2.2K-J-1/10W RES,M 3.3K-J-1/10W RES,M 5.6K-J-1/10W RES,M 10K-J-1/10W RES,M 22K-J-1/10W RES,M 1K-J-1/10W RES,M 22K-J-1/10W RES,M 15K-J-1/10W RES,M 3.9K-J-1/10W RES,M 10K-J-1/10W CT-20D12DF-1 RES,M 10K-J-1/10W CT-20G7DF-1, CT-2017F-1 RES,M 3.3K-J-1/10W CT-20D12DF-1 RES,M 100-J-1/10W RES,M 1K-J-1/10W RES,M 10K-J-1/10W CT-20D12DF-1 RES,M 10K-J-1/10W RES,M 10K-J-1/10W RES,M 470-J-1/10W RES,M 1.8MEG-J-1/10W
302-02
- 11 -
PARTS LIST
PARTS LIST
SWITCHES
SWITCH SWITCH SWITCH SWITCH SWITCH 302-02
- 12 -
TRANSFORMERS
TRANSFORMER TRANSFORMER, FLYBACK TRANSFORMER CRYSTAL OSCILLATOR CRYSTAL
CRYSTALS/FILTERS
ASSY, CABINET FRONT CT-2017F-1 ASSY, CABINET FORNT CT-20G7DF-1, CT-20D12DF-1 ASSY. JACK 1A/V CT-20D12DF-1 ASSY. JACK A/V
OTHERS
TNR001 ENG36604GR TNR001 ENG36610G M001 M002 M003 M004 M005 DY M006 M007 DEG M008 M009 M010 M011 M012 TSX2AA0111-1 A51KRE89XDT TJSC00300 0FMK014ZZ JH291U-009 TLY2AA001 TMM2A30702 TXF3A011DB2 TSP2AA008 TSN63115-4 TAS2AA0012 TXFKU05ESER TXFKU06BSER TXFKU06ESER TUNER TUNER CRT 20 CRT SOCKET CONVERGENCE CORRECTOR STRIP YOKE, CONVERGENCE DEFLECTION YOKE WEDGE, YOKE ASSY. DAG GROUND COIL, DEGAUSSING 20 INCH MAGNET, PURITY SPEAKER 16-OHM 1.5W ASSY, CABINET BACK CT-20G7DF-1 ASSY, CABINET BACK CT-2017F-1 ASSY, CABINET BACK CT-20D12DF-1
CT-2017F-,1, CT-20G7DF-1
ACCESORIES
M020 M021 EUR501450 EUR511502 REMOTE CONTROL CT-20G7DF-1, CT-2017F-1 REMOTE CONTROL CT-20D12DF-1 BATTERY COVER, REMOTE CONTROL CT-2017F-,1, CT-20G7DF-1 BATTERY COVER, REMOTE CONTROL CT-20D12DF-1 OWNERS MANUAL
M022
UR50EC1190A
M023
UR51EC975A
M024 M025
TQB2AA0370-2 TQB2AA0431-2
CT-2017F-1
OWNERS MANUAL CT-20G7DF-1, CT-20D12DF-1
CAPACITOR
TYPE
C E P S T Ceramic Electrolytic Polyester Styrol Tantalum C D F J K L M P Z
TOLERANCE
1% 5% 10% 20% 2%
TOLERANCE
0.25pF 0.5pF 1pF 5% 10% 15%
RES, C 270-J-1/4
CAP, P .068UF-K-50V
302-02
- 13 -
Parts List
PARTS LIST
20%
Notes
IMPORTANT SAFETY NOTICE
THIS SCHEMATIC DIAGRAM INCORPORATES SPECIAL FEATURES THAT ARE IMPORTANT FOR PROTECTION FROM X-RADIATION, FIRE AND ELECTRICAL SHOCK HAZARDS. WHEN SERVICING IT IS ESSENTIAL THAT ONLY MANUFACTURERS SPECIFIED PARTS BE USED FOR THE CRITICAL COMPONENTS DESIGNATED WITH A IN THE SCHEMATIC. CHIP TRANSISTOR LEAD DESIGNATION
B E
SCHEMATIC NOTES
1. Resistors are carbon 1/4W unless noted otherwise. 2. Capacitors are ceramic 50V unless noted otherwise. 3. Coil value notes is inductance in H. 4. Test point indicated by ; Test point but no pin . 5. Components indicated with are critical parts and replacement should be made with manufacture specified replacement parts only. (BOLD LINE) indicates the route of B+ supply. 7. The schematic diagrams are current at the time of printing and are subject to change without notice. 8. Ground symbol indicates HOT GROUND CONNECTION; indicates COLD GROUND. 6.
NOTE: All other component symbols are used for engineering design purposes.
VOLTAGE MEASUREMENTS
1. Voltage measurement: AC input to the Receiver is 120V. NTSC (HD, 1125i & 525P when applicable) signal generator is connected to the antenna of the Receiver. (Color bar pattern of 100 IRE white and 7.5 IRE black.) All Picture and Audio adjustments are set to Normalize. TV ANT/CABLE - (Set-Up Menu) in TV/ANT Mode Volume - Min. TV/Video SW - TV position Audio Mode - Stereo Voltage readings are nominal and may vary 10% on active devices. Some voltage reading will vary with signal strength and picture content. Supply voltages are nominal.
2. Ground symbol indicates ground lead connection of meter. Incorrect ground connection will result in erroneous readings.
CAUTION: Incorrect ground connection of the test equipment will result in erroneous readings.
WAVEFORM MEASUREMENTS
4. All video and color waveforms are taken with a wideband scope and a probe with low capacitance (10 to 1). Shape and peak altitudes may vary depending on the type of Oscilloscope used and its settings. 5. Ground symbol shown on waveform number indicates (Hot) ground lead connection of the Oscilloscope.
1.
indicates waveform measurement. (Measurement can be taken at the best accessible location in common to the indicated point.) 2. Taken with an NTSC signal generator connected to the antenna terminal. (NTSC color bar pattern of 8 bars of EIA colors, 100 IRE white and 7.5 IRE black.) 3. Customer Controls (Picture/Audio Menu) are set to Normalize. Volume is set to MIN.
CAUTION: Incorrect ground connection of the test equipment will result in erroneous readings.
- 14 -
Notas:
NOTA DE SEGURIDAD
LOS DIAGRAMAS ELCTRICOS INCLUYEN CARACTERSTICAS ESPECIALES MUY IMPORTANTES PARA LA PROTECCIN CONTRA RAYOS-X, QUEMADURAS Y DESCARGAS ELCTRICAS. CUANDO SE DE SERVICIO ES IMPORTANTE USAR PARA REEMPLAZO DE COMPONENTES CRITICOS, SOLO PARTES ESPECIFICADAS POR EL FABRICANTES. LOS COMPONENTES CRITICOS ESTAN SEALADOS EN LOS DIAGRAMAS POR EL SIMBOLO . IDENTIFICACIN DE TERMINALES PARA TRANSISTORES EN CHIP
B E
6.
3. 4.
7. 8.
5.
NOTA: Los demas smbolos componentes incluidos usados con fines de diseo.
de son
MEDICIN DE VOLTAJES
1. Medicin de voltaje: El voltaje de entrada al Receptor es de 120V de Corriente Alterna. Un generador de patrones con formato NTSC se conecta a la entrada de la antena. (Patrn de Barras de Colores con 100 IREs para el Blanco y 7.5 IREs para el Negro.) Los ajustes de los Menus Picture y Audio se normalizan. En el Men Set-Up, en la opcin ANTENA, se selecciona el modo de CABLE. El nivel de Volumen se minimiza. De los modos TV y Video, seleccionar el modo TV. Seleccionar modo Estereo del Audio. Las mediciones de los voltajes son nominales y pueden variar hasta 10% en componentes en funcionamiento. Las lecturas de los voltajes pueden variar por la potencia de la seal y el contenido de la imagen. Las fuentes de voltajes son nominales. El smbolo indica el tipo de tierra que se utiliza en la conexin del medidor.
2.
PRECAUCION: SI no se utiliza la conexin a la tierra adecuada, se obtendrn mediciones equivocadas y podra daar el equipo de medicin.
PRECAUCION: Si no se utiliza la conexin a la tierra adecuada, se obtendrn mediciones equivocadas y podra daar el equipo de medicin.
- 15 -
PARTS LIST
banda alta y con un punta de prueba de baja capacitancia (10 a 1). La forma y amplitud de las ondas puede variar segn el tipo de osciloscopio que se utilice y sus caractersticas. 5. El smbolo de tierra que aparece junto al nmero de la forma de onda, indica que se utiliza conexin a Tierra Caliente en el extremo negativo de la punta de prueba.
TNP2AH048DR
- 16 -
CT-2017F-1, CT-20G7DF-1
CT-2017F-1, CT-20G7DF-1
- 17 -
TNP2AH048DR
TNP2AH048DR
- 18 -
CT-2017F-1, CT-20G7DF-1
CT-2017F-1, CT-20G7DF-1
- 19 -
TNP2AH048DR
TNP2AH048DR
- 20 -
CT-2017F-1, CT-20G7DF-1
- 21 -
TNP2AA124AF
TNP2AH048DS
- 22 -
CT-20D12DF-1
CT-20D12DF-1
- 23 -
TNP2AH048DS
TNP2AH048DS
- 24 -
CT-20D12DF-1
CT-20D12DF-1
- 25 -
TNP2AH048DS
TNP2AH048DS
- 26 -
CT-20D12DF-1
NOTES:
- 27 -
NOTES
- 28 -
ALL MODELS
ALL MODELS
- 29 -