Professional Documents
Culture Documents
Ec2255 - CS - Unit - 1
Ec2255 - CS - Unit - 1
Ec2255 - CS - Unit - 1
Closed loop system: Control systems in which the output has an effect upon the input quantity in order to maintain the desired output value are called closed loop system.
Advantages of open loop system: It is much simpler and less expensive No sensors are needed to measure the variables to provide feed back The open loop systems are easier to construct Generally the open loop system are stsble
Disadvantages of open loop system: This systems are inaccurate and unreliable The changes in the output due to external disturbance are not corected automatically There is no compensation for any disturbances entering into the system Its performance is highly depends on the properties of the system Advantages of closed loop system: The closed loop system are accurate It is less affected by noise It compensates for disturbances Less sensitive to system parameter variation Disadvantages of closed loop system: These systems are more complex and more expensive The feedback in closed loop system may lead to oscillatory response The feedback reduces the overall gain of the system If the closed loop system is not properly designed, the feedback system may lead to undesirable response
Mathematical models of control systems Relate the input and output of system with mathematical relation called differential equation. A system or the mathematical model of a system is linear if it satisfies ar obeys the principle of superposition and homogenity.
Transfer function The ratio between laplace transform output to laplace transform input with zero initial condition called transfer function
Modeling of electrical system Basic elements Resister : Inductor : Capacitor: Mathematical Models of Electrical Elements
PROBLEM 1: Find the transfer function relating the capture voltage V c (S) and the input voltage V(S) as shown in the figure.
To find:
Note: OUTPUT Vc(t) Vc(S) V(t) V(S)
Taking laplace transform, R C S Vc (S) + L C S2 Vc (S) + Vc (S) = V(S) Vc (S) [L C S2 + R C S + 1] = V(S) T.F = =
PROBLEM 2: Obtain the transfer function of electrical network as shown in the figure.
To find:
= = = E(S)
Spring (K):
Friction:
Spring:
Analogy Systems:
Differential equation for transfer function mechanical and differential equation of electrical equation is equal called analogous system. Force Voltage Analogy:
PROBLEM 3: Draw the equivalent mechanical system of the given system. Hence write the set of equilibrium equations for it and obtain electrical analogous circuits using, (i) F V Analogy and (ii) F I Analogy
Equivalent Circuit
Block Diagram Reduction Techniques: A block diagram with several summers and pick off points can be reduces to a single block, by using block diagram algebra, consisting of the following rules.
PROBLEM 4: Find the overall transfer function of the system, using block diagram reduction technique.
Solution: Step1: Using rule 6, the feedback loop with G2 and H2 is replaced by a single block
Step2: The two blocks in the forward path are in cascade and can be replaced using rule 1.
Solution: Step1: Move pick off point 2 to left of G2 and combine G2 G3 in cascade. Further G2 G3 and G4 have same inputs and the outputs are added at summer III. Hence they can be added and represented by a single block.
Step 2: Moving the pick off point 1 to right of block (G2 G3 + G4),
Where Mk is the kth forward path gain, is the determinant of the graph, is given by,
Where P mr is the product of the gains of mth possible combination of r non touching loops. Or
= 1 (sum of gains of individual loops) + (sum of gain products of possible combinations of 2 non touching loops) (sum of gain products of all possible combinations of 3 non touching loops) + .
and k is the value of for that part of the graph which is non touching with k th forward path.
PROBLEM 6: Find the transfer function for the following signal flow graph
Solution Name the various summing and take off points to draw the signal flow graph,
Solution The value of the variable is the algebraic sum of all the signals entering at the node, representing that variable. The variables are X 1, X2, X3, X4 while the gains are A 21, A23, A31, A32, A33, A42 and A43 So selecting nodes representing variables and simulating differential equations
April/May 2010
1.
2.
3.
Nov/Dec 2010
4.
5.
6.
7.
May/June 2011
8.
9.
10.