Professional Documents
Culture Documents
Morin TYCO Valves
Morin TYCO Valves
General Applications
Technical Data
Supply pressure:
40 to 160 psig
(see torque chart,
MORMC-0333)
Supply medium:
Temperature rating
Standard range:
Optional range:
Angular rotation:
Flow Control
-20F to 210F
-65F to 300F
90 degrees
8 degrees
Morin is either a trademark or registered trademark of Tyco International Services AG or its affiliates in the
United States and/or other countries. All other brand names, product names, or trademarks belong to
their respective holders.
Copyright 2012 Tyco Flow Control. All rights reserved.
MORMC-0024-US-1202
Principles of Construction
Using high quality materials of construction and modern
rugged design concepts Morin becomes the standard for
low cost valve actuation while providing high quality
performance.
The S actuator housings are all machined from 316
stainless steel castings. This produces a rugged, low cost
product through reduced machining time and by eliminating
wasteful excess material.
Any components that rotate or slide during operation, such
as the high strength stainless steel output shaft, stainless
steel piston rod, stainless steel thrust pin or the stainless
steel piston, are all supported by replaceable friction
reducing bearings.
Ingress Protection
Actuator meets IP66 and IP67 for
standard units.
Hydraulic Override
Spring
Break
Break Torque
100
100
Air
Stroke
Spring
Stroke
Proximity Preparation
75
Lockout Device
75
Torque
Torque
Jackscrew Override
125
50
Spring
End
25
Air
End
45
Running
Torque
50
25
90
Stroke
45
90
Stroke
MORMC-0024
2
Materials of Construction
Double Acting Models 003 to 100 and 144 (Except Model 135)
Bearings
Teflon Composite
Scotch Yoke
17-4PH Stainless Steel with
440C Roller Bearings
Piston
316 Stainless Steel
Piston Bearing
Teflon
Cylinders
316 Stainless Steel
Bearings
Teflon Composite
Scotch Yoke
17-4PH Stainless Steel with
440C Roller Bearings
Piston
316 Stainless Steel
Piston Bearing
Teflon
Cylinders
316 Stainless Steel
MORMC-0024
3
Manual Options
To provide the actuation package best suited for your application, the Morin line offers a full range
of manual accessories.
Lockout
AWWA
+ F/C
Proximity Switch
Preparation
MORMC-0024
4
Mechanical Data
Notes:
Mechanical Data
1. Air Consumption:
Cubic inches shown in chart represent
actual free air volume in cylinder between
piston and end cap when furthest apart. Air
consumption will vary depending on supply
pressure. To determine standard cubic feet
per minute use the following formula:
(_____ )(________________)(
Vol. in3
1728
14.7
Strokes/Minute
Actuator
Model
Number
of
Pistons
Cylinder
Bore
(inch)
Stroke
(inch)
Volume1
Cubic In
90 Stroke
Cycle Time2
Seconds
90 Stroke
003
2.250
1.5
0.3
006
012
1
2
2.750
2.750
2
2
12
23
0.5
0.7
10
12
023
036
1
1
4.375
5.438
3
3
45
70
1.0
1.5
27
30
050
072
1
2
6.250
5.438
3
3
92
137
2.2
2.5
36
37
100
135
2
1
6.250
8.250
3
5
182
267
3.0
4.5
46
165
144
210
4
1
5.438
10.250
3
5
274
413
3.5
5.0
74
185
270
370
2
1
8.250
12.250
5
6
526
707
6.0
8.0
210
390
420
575
2
1
10.250
15.500
5
6
816
1132
8.5
9.5
257
519
740
1150
2
2
12.250
15.500
6
6
1395
2245
10.0
12.0
530
775
1480
2380
2
2
12.250
15.500
12
12
2744
4444
20.0
24.0
850
1050
003
006
1
1
2.250
2.750
1.5
2
6
12
0.3
0.5
6
11
012
023
2
1
2.750
4.375
2
3
23
45
0.7
1.0
14
34
036
046
1
2
5.438
4.375
3
3
70
88
1.5
2.0
42
43
072
100
2
2
5.438
6.250
3
3
137
182
2.5
3.0
55
64
135
144
1
4
8.250
5.438
5
3
267
274
4.5
3.5
210
110
210
270
1
2
10.250
8.250
5
5
413
526
5.0
6.0
235
250
370
420
1
2
12.250
10.250
6
5
707
816
8.0
8.5
540
379
575
740
1
2
15.550
12.250
6
6
1132
1395
9.5
10.0
779
704
1150
1480
2
2
15.550
12.250
6
12
2245
2744
12.0
20.0
1082
1650
2380
15.500
12
4444
24.0
1850
Weight
(lbs.)
Double Acting
SCFM =
( )(
45
_____
1728
)( )
80 +14.7
_________
14.7
SCFM = 0.84
Spring Return
Typical Section
Double Acting/One Piston
Typical Section
Spring Return/Two Pistons
MORMC-0024
5
Stroke in degrees
-5
10
15 20 25 30 35 40 45 5055 60 65 70 75 80 85
90
95
Moment arm
minimum (X)
at mid stroke (45)
Y
Moment arm
maximum (Y) at end
of stroke (90)
Normal 90 stroke
X = Min. moment arm
Y = Max. moment arm
100 stroke
For max. moment arm at any stroke position multiply min. moment by secant
Output Torques
Output Torques (lb. in.) Double Acting air to air
Actuator
Model
40
50
60
70
80
120
130
140
150
160
003
Start / End
Minimum
173
110
219
140
259
165
305
190
345
220
391
250
431
280
472
310
518
330
006
Start / End
Minimum
300
235
375
290
450
350
525
405
600
460
675
520
750
575
825
640
900
690
975
750
1050
810
1125
870
1200
940
012
Start / End
Minimum
690
470
863
580
1035
700
1208
810
1380
940
1553
1050
1725
1170
1898
1275
2070
1405
023
Start / End
Minimum
1150
855
1450
1070
1725
1285
2010
1500
2300
1710
2585
1925
2875
2140
3160
2350
3450
2570
3740
2780
4020
3000
4300
3210
4600
3420
036
Start / End
Minimum
1980
1370
2475
1710
2970
2055
3465
2400
3960
2740
4455
3080
4950
3425
5445
3770
5940
4110
6435
4450
6930
4800
7425
5140
7920
5480
050
Start / End
Minimum
2500
1840
3125
2300
3750
2760
4375
3220
5000
3680
5630
4140
6250
4600
6875
5060
7500
5520
8125
5980
8750
6440
9375
6900
10000
7360
072
Start / End
Minimum
3960
2740
4950
3425
5940
4110
6930
4790
7920
5480
8910
6160
9900
6850
10780
7540
11880
8220
100
Start / End
Minimum
5000
3680
6250
4600
7500
5520
8750
6440
10000
7360
135
Start / End
Minimum
7088
5250
8862
6565
10631
7875
12406
9185
14175
10500
15950
11810
17724
13125
19488
14440
21263
15750
144
Start / End
Minimum
7200
5460
9000
6850
10800
8210
12600
9580
14400
10960
210
Start / End
Minimum
11550
8160
14438
10200
17325
12240
20213
14280
23100
16320
25988
18360
28875
20400
31763
22440
34650
24480
37538
26520
270
Start / End
Minimum
14175
10500
17719
13125
21263
15750
24806
18375
28350
21000
31894
23625
35438
26250
38981
28875
42525
31500
370
Start / End
Minimum
19795
13080
24744
16350
29693
19620
34641
22890
39590
26160
44539
29430
49488
32700
54436
35970
59385
39240
420
Start / End
Minimum
21000
16320
26250
20400
31500
24480
36750
28560
42000
32640
575
Start / End
Minimum
31913
22440
39849
28050
47869
33660
55833
39270
63825
44880
71806
50490
79781
56100
87757
61710
740
Start / End
Minimum
38850
26160
48563
32700
58275
39240
67988
45780
77700
52320
87413
58860
97125
65400
106838
71940
1150
Start / End
Minimum
60375
44880
75469
56100
90563
67320
105656
78540
120750
89760
1480
Start / End
Minimum
74000
46621
92500
58276
111000
69931
129500
81586
148000
93242
166500
104897
2380
Start / End
Minimum
119000
75506
148750
94383
178500
113259
208250
132136
238000
151013
185000
116552
MORMC-0024
6
MAXIMUM OPERATING
PRESSURE = 120 psi
MAXIMUM OPERATING
PRESSURE = 100 psi
203500
128207
23037
17060
24812
18375
222000
139862
28350
21000
MAXIMUM OPERATING
PRESSURE = 120 psi
40425
28560
43313
30600
46200
32640
64334
42510
69283
45780
74231
49050
79180
52320
26576
19690
119669 127650
84150 89760
MAXIMUM OPERATING
PRESSURE = 120 psi
MAXIMUM OPERATING
PRESSURE = 120 psi
MAXIMUM OPERATING
PRESSURE = 120 psi
MAXIMUM OPERATING
PRESSURE = 120 psi
Output Torques
Output Torques (lb. in.) Single Acting spring return
Actuator
Model
003
006
012
023
036
046
072
100
135
144
210
270
370
420
575
740
1150
1480
2380
40
50
60
70
80
120
130
140
150
160
Start
Minimum
End
Start
Minimum
End
110
50
55
195
99
110
135
63
70
245
123
137
160
72
80
290
151
168
185
86
95
340
175
194
210
95
105
390
199
221
Start
Minimum
End
Start
Minimum
End
390
208
231
750
360
400
485
263
292
945
459
510
585
312
347
1125
540
600
680
366
407
1305
635
705
780
416
462
1500
720
800
1680
815
905
1870
905
1005
2250
1080
1200
2615
1269
1410
3000
1440
1600
Start
Minimum
End
Start
Minimum
End
1170
567
630
1500
720
800
1460
711
790
1870
905
1005
1755
855
950
2250
1080
1200
2050
990
1100
2615
1269
1410
2340
1134
1260
3000
1440
1600
2630
1274
1415
2925
1418
1575
3510
1701
1890
3880
1880
2090
4095
1985
2205
4700
2250
2500
Start
Minimum
End
Start
Minimum
End
2340
1134
1260
3250
1575
1750
2925
1418
1575
4060
1971
2190
3510
1701
1890
4880
2358
2620
4095
1985
2205
5690
2754
3060
4700
2250
2500
6500
3150
3500
Start
Minimum
End
Start
Minimum
End
4390
2554
2838
4680
2268
2520
5485
3186
3540
5850
2835
3150
6580
3829
4254
7020
3402
3780
7680
4466
4962
8190
3969
4410
8775
5103
5670
9400
4500
5000
9875
5740
6378
10970
6377
7086
13160
7657
8508
15355
8932
9924
17550
10206
11340
Start
Minimum
End
Start
Minimum
End
6825
3639
4043
8780
4683
5203
8530
4544
5049
10970
5846
6496
10240
5455
6061
13160
7019
7799
11940
6366
7073
15355
8187
9097
13650
7277
8085
17550
9356
10395
15350
8187
9097
19746
10524
11693
17060
9098
10109
21940
11693
12992
20475
10915
12128
23890
12731
14146
27300
14553
16170
Start
Minimum
End
Start
Minimum
End
12025
6701
7446
13650
6946
7718
15030
9403
10448
17060
8685
9650
18040
10050
11167
20475
10418
11576
21045
11727
13030
23890
12153
13503
24050
13404
14893
27300
13892
15435
27055
15080
16756
30705
15630
17367
30060
16757
18619
34120
17369
19299
36075
20105
22339
42090
23453
26059
48100
26807
29785
Start
Minimum
End
Start
Minimum
End
18690
9507
10563
24050
13404
14893
23360
11888
13209
30060
16757
18619
28030
14261
15845
36075
20105
22339
32700
16642
18491
42090
23453
26059
37375
19018
21131
48100
26807
29785
42045
21390
23767
54108
30163
33514
46720
23767
26408
60120
33514
37238
56060
28530
31700
65400
33283
36981
74750
38037
42263
Start
Minimum
End
Start
Minimum
End
37375
19018
21131
48100
23310
25900
46720
23767
26408
60125
29138
32375
56060
28530
31700
72150
34965
38850
65400
33283
36981
84175
40712
45235
74750
84090
38037
42790
42263
47544
96200 108225
46620
52448
51800
58275
93440
47534
52815
120250
58275
64750
Start
Minimum
End
77350
37485
41650
96688
46857
52063
116025 135363
56228 65599
62475 72888
154700 174038
74970
84342
83300
93713
193375
93713
104125
MAXIMUM OPERATING
PRESSURE = 100 psi
MAXIMUM OPERATING
PRESSURE = 100 psi
MAXIMUM OPERATING
PRESSURE = 120 psi
MAXIMUM OPERATING
PRESSURE = 120 psi
MAXIMUM OPERATING
PRESSURE = 120 psi
MAXIMUM OPERATING
PRESSURE = 120 psi
MAXIMUM OPERATING
PRESSURE = 120 psi
MORMC-0024
7
Dimensions
Models 012, 046, 072, 100 and 144*
Q Typical
A
B
C 1 (sq)
C 2 (sq)
P NPT Typical
H
Diameter
E
D
B
316 SS
J
C 1 (sq)
F (dia)
K
L
G
P NPT Typical
H
Diameter
MORMC-0024
8
C1
C2
003DA
9.06
3.50
2.69
3.06
0.75
1.00
1.37
2.75
3.25
1.00
1/8
0.62
006DA
12.34
5.97
3.18
3.91
1.00
0.10
1.38
1.50
3.00
4.75
1.31
1/8
1.00
012DA
12.74
6.37
3.18
3.18
3.91
4.81
0.10
1.38
1.50
3.00
4.75
1.31
1/8
1.00
023DA
18.60
8.81
4.81
5.78
1.43
0.25
1.75
2.16
4.31
6.69
1.88
1/4
1.15
1.25
036DA
18.48
8.81
5.81
6.28
1.43
0.75
1.75
2.16
4.31
6.69
1.88
1/4
050DA
18.49
8.81
7.13
6.94
1.43
1.41
1.75
2.16
4.31
6.69
1.88
1/4
1.25
072DA
19.33
9.67
5.81
5.81
6.28
6.38
0.75
1.75
2.16
4.31
6.69
1.88
1/4
0.83
100DA
19.35
9.68
7.12
7.12
6.94
6.38
1.41
1.75
2.16
4.31
6.69
1.88
1/4
0.75
144DA
19.33
9.67
5.81
5.81
6.28
6.38
0.75
1.75
5.05
10.10
12.49
1.88
1/4
0.875
C1
C2
003SR
9.06
3.50
2.69
3.06
0.75
1.00
1.37
2.75
3.25
1.00
1/8
0.62
006SR
14.44
5.97
3.18
3.91
1.00
0.10
1.38
1.50
3.00
4.75
1.31
1/8
1.00
012SR
14.84
6.37
3.18
3.18
3.91
4.55
0.10
1.38
1.50
3.00
4.75
1.31
1/8
1.00
023SR
21.82
8.81
4.81
5.78
1.43
0.25
1.75
2.16
4.31
6.69
1.88
1/4
1.25
036SR
23.51
8.81
5.81
6.28
1.43
0.75
1.75
2.16
4.31
6.69
1.88
1/4
1.25
046SR
22.80
9.79
4.81
4.81
5.93
6.24
0.25
1.75
2.16
4.31
6.69
1.88
1/4
1.25
072SR
24.37
9.67
5.81
5.81
6.28
5.99
0.75
1.75
2.16
4.31
6.69
1.88
1/4
1.25
1.25
1.25
100SR
24.38
9.68
7.12
7.12
6.94
5.99
1.41
1.75
2.16
4.31
6.69
1.88
1/4
144SR
24.37
9.67
5.81
5.81
6.28
5.99
0.75
1.75
5.05
10.10
12.49
1.88
1/4
MORMC-0024
9
Dimensions
Models 270, 420, 740, and 1150
A
B
Q Typical
C
G
P NPT Typical
H
Diameter
E
Q Typical
B
J
K
F Diameter
G
P NPT Typical
H
Diameter
D
B
Q Typical
J
K
G
E
MORMC-0024
10
P NPT Typical
Model
135DA
32.87
15.88
9.50
10.44
2.75
1.00
4.38
8.13
11.82
3.19
3/8
1.50
210DA
33.26
15.88
11.50
11.44
2.75
2.00
4.38
8.13
11.82
3.19
1/2
2.00
1.50
270DA
33.99
16.99
9.50
10.44
11.72
1.00
4.38
8.13
11.82
3.19
3/8
370DA
41.64
19.75
13.50
16.75
3.50
2.69
6.00
5.44
9.50
14.81
6.88
1/2
1.50
420DA
34.75
17.38
11.50
11.44
11.22
2.00
4.38
8.13
11.82
3.19
1/2
1.75
575DA
42.42
19.75
17.00
18.50
3.50
4.50
6.00
5.44
9.50
14.81
6.88
3/4
2.00
740DA
44.15
20.07
13.50
16.75
15.50
2.69
6.00
5.44
9.50
14.81
6.88
1/2
1.50
1.85
1150DA
45.39
22.69
17.00
18.50
14.88
4.50
6.00
5.44
9.50
14.81
6.88
3/4
1480DA
70.65
35.85
13.50
21.57
26.94
0.44
7.06
13.38
7.58
1/2
2.15
2380DA
88.29
36.51
17.00
22.08
25.06
2.19
7.06
13.38
7.58
3/4
2.50
Q
1.75
135SR
39.46
15.88
9.50
10.44
2.75
1.00
4.38
8.13
11.82
3.19
3/8
210SR
42.67
15.88
11.50
11.44
2.75
2.00
4.38
8.13
11.82
3.19
1/2
2.12
270SR
40.57
16.99
9.50
10.44
10.95
1.00
4.38
8.13
11.82
3.19
3/8
1.75
370SR
52.00
19.75
13.50
16.75
3.50
2.69
6.00
5.44
9.50
14.81
6.88
1/2
1.75
420SR
44.17
17.38
11.50
11.44
10.36
2.00
4.38
8.13
11.82
3.19
1/2
2.12
575SR
54.25
19.75
17.00
18.50
3.50
4.50
6.00
5.44
9.50
14.81
6.88
3/4
2.50
2.12
740SR
53.96
22.07
13.50
16.75
14.75
2.69
6.00
5.44
9.50
14.81
6.88
1/2
1150SR
57.25
22.69
17.00
18.50
13.75
4.44
6.00
5.44
9.50
14.81
6.88
3/4
2.50
1480SR
86.98
35.85
13.50
21.57
26.30
0.44
7.06
13.38
7.58
1/2
2.50
2380SR
88.29
36.51
17.00
22.08
25.10
2.19
7.06
13.38
7.58
3/4
2.50
MORMC-0024
11
Mounting Details
Model 003 Top and bottom of housing (symmetrical)
1/4
7/16
0.44
Typ.
SYM.
0.438 square
0.435
0.157/0.160 wide
0.197/0.205 deep
Drive Slot
A
Section A - A
Models 006 to 100 and 144 Top and bottom of housing (symmetrical)
Models 006 and 012 = 0.87
Models 023 to 100 = 1.18
1.00 typ.
SYM.
0.157/0.160 wide
0.197/0.205 deep
Drive Slot
NAMUR Drive
Both Ends
B
Section B - B
Models 135, 210, 270 and 420 Bottom of housing ISO 5211-F16
3/4
1.18
C
Section C - C
Models 135, 210, 270 and 420 Top of housing - Mounting details
0.251 CBore x 0.209 Deep
M6 Tap x 1/2" Deep
TUHS
NEPO
NEPO
NAMUR Adapter
SHUT
0.998/0.995
square
0.197
0.205
1.18
MORMC-0024
12
3.69
Mounting Details
Models 370, 575, 740 and 1150 Bottom of housing ISO 5211-F30
3.000/2.994 Diameter Shaft
3/4 sq. x 3.75 Long Keyway
with 0.031 radius inside key way corners
(to be used with 3/4" x 3 13/16" key)
3/4
5.31
1.18
4.56
22.5 Typ.
D
Section D - D
Models 370, 575, 740 and 1150 Top of housing Mounting details
0.251 CBore x 0.209 Deep
M6 Tap x 1/2" Deep
SHUT
NAMUR Adapter
OPEN
OPEN
0.197
0.205
SHUT
0.998/0.995 square
1.18
E
1 - 8 UNC Tap x 13/4" Deep
(8) Places as Shown on
14.02 Diameter Bolt Circle
1.18
22.5
Typ.
E
Section E - E
NAMUR Adapter
0.996/0.993
square
0.197
0.205
1.18
MORMC-0024
13
Model Numbering
S
- 270
00
- JSO
Actuator Model
S Stainless Steel
Actuator Size
Model code based on approx. torque
symmetrical double acting at 80 psig
003
072
575
006
100
740
012
135
1150
023
210
1480
036
270
2380
046
370
050
420
Interface Bolting
U UNC Mounting Threads
M Metric Mounting Threads
Function
D Double Acting
S Spring Return
Configurations
Spring code denotes air pressure divided by 10 where spring force gives
the same spring end torque as air end torque using symmetric yoke.
00 No spring (double acting)
04 40 pound spring
05 50 pound spring
06 60 pound spring
Etc. See Morin Torque Book (MORMC-0333) for available springs
Option
(blank) No options (standard configuration)
Note: Some codes can be used in combination. Indicate by stacking " separated by "-".
Consult your sales representative for possible combinations.
How To Order
1. Double Acting example:
Air supply: 80 psig
Break torque: 7,200 lb.in.
S-072U-D000
S:
Series
072:
Model number
U:
UNC mounting threads
D000:
Double acting
MORMC-0024
14
AccuTrak/Quantum 366
Network Solutions*
Intellis is a family of industrial control field Network Control Monitors which use embedded
control systems to automate valves and link field I/O to the host PLC or DCS. Each monitor
is assigned a unique address and accepts input/output signals from valve position
sensors, solenoids and external alarm and control devices. Hall Effect sensors are utilized
for valve position monitoring. Low-power Falcon solenoid valve provides integrated
actuation control. Network interface modules Pacs allow communication via a protocol of
choice. Westlock Intellis Network Control Monitors are available for linear or rotary
applications in all area classifications.
Notes:
Stainless Steel, AccuTrak, Quantum, Intellis Network Solutions and Positioners * please
consult your sales representative for the availability of global certifications such
as ATEX, IEC, GOST, CSA and InMetro for specific configurations in these product lines,
as approvals may vary.
MORMC-0024
15
Also Available
The Series B and C Actuators
Ductile Iron
Teflon
Chrome-plated Steel
17-4PH Stainless Steel
or Ductile Iron
Sintered Bronze
or Teflon composite
Tyco Flow Control (TFC) provides the information herein in good faith but makes no representation as to its comprehensiveness or accuracy. This data sheet is intended only as a guide to TFC products and services.
Individuals using this data sheet must exercise their independent judgment in evaluating product selection and determining product appropriateness for their particular purpose and system requirements. TFC MAKES NO
REPRESENTATIONS OR WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO
THE INFORMATION SET FORTH HEREIN OR THE PRODUCT(S) TO WHICH THE INFORMATION REFERS. ACCORDINGLY, TFC WILL NOT BE RESPONSIBLE FOR DAMAGES (OF ANY KIND OR NATURE, INCLUDING
INCIDENTAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES) RESULTING FROM THE USE OF OR RELIANCE UPON THIS INFORMATION. All Patents and Patents Pending in the U.S. and foreign countries are
property of their respective owners. Tyco reserves the right to change product designs and specifications without notice. All registered trademarks are the property of their respective owners. Printed in the USA.
MORMC-0024
16
www.tycoflowcontrol.com