This document summarizes an experiment to synthesize 2-methoxychalcone via an aldol condensation reaction between acetophenone and ortho-methoxybenzaldehyde. The reaction product was purified via recrystallization and characterized using melting point, IR spectroscopy, 1H NMR and 13C NMR. These analyses identified the product as 2-methoxychalcone. The yield was 52%, which was decent but not ideal, suggesting some product was lost during the recrystallization purification step. The document concludes the experiment successfully demonstrated an important carbon-carbon bond forming aldol condensation reaction.
This document summarizes an experiment to synthesize 2-methoxychalcone via an aldol condensation reaction between acetophenone and ortho-methoxybenzaldehyde. The reaction product was purified via recrystallization and characterized using melting point, IR spectroscopy, 1H NMR and 13C NMR. These analyses identified the product as 2-methoxychalcone. The yield was 52%, which was decent but not ideal, suggesting some product was lost during the recrystallization purification step. The document concludes the experiment successfully demonstrated an important carbon-carbon bond forming aldol condensation reaction.
This document summarizes an experiment to synthesize 2-methoxychalcone via an aldol condensation reaction between acetophenone and ortho-methoxybenzaldehyde. The reaction product was purified via recrystallization and characterized using melting point, IR spectroscopy, 1H NMR and 13C NMR. These analyses identified the product as 2-methoxychalcone. The yield was 52%, which was decent but not ideal, suggesting some product was lost during the recrystallization purification step. The document concludes the experiment successfully demonstrated an important carbon-carbon bond forming aldol condensation reaction.
Synthetic FFR #3 TA: Kristin Beiswenger December 11 th , 2013 "#$%& ' I. Introduction Much of the focus in pharmaceutical development lies in utilizing the full potential of previously uncovered biologically active compounds. Fully understanding the role that certain molecules can play in biochemical pathways is essential for the development of innovative treatment options in medicine. 1
For instance, a class of compounds known as chalconoids is currently under investigation in order to exploit a wide range of biological applications. 1
Chalcones are trans-1,3-diaryl-2-propen-1-ones, containing an !,"-unsaturated ketone between two aromatic rings. 1 Varying substituent groups on these rings allow for great diversity within the chalconoid class, as they can serve as precursors, intermediates, or products in many biological reactions. 1,2 Notably, chalcones are important in the natural synthesis of flavonoids and isoflavonoids, which are plant metabolites. In humans, chalcones and their derivatives have been shown to exhibit anticancer, antiprotozoal, antimalarial, antimicrobial, antioxidant, and antifungal properties with limited toxicity. 2 Additionally, certain chalcones can serve as inhibitors for mammalian enzymes such as monoamine oxidase (MAO) and cyclooxygenase (COX), which suggests that these ketones can be used in pain management. 1,2
Accordingly, chalcone synthesis has become a topic of high interest in pharmaceutical development. Chalcone formation can be achieved via the Claisen-Schmidt reaction, which is a relatively simple and inexpensive example of a mixed aldol condensation. 2,3 Aldol condensation reactions comprise of an aldol reaction (nucleophilic addition/alpha substitution) and subsequent dehydration of the aldol product to yield an !,"-unsaturated carbonyl. 2 Carbonyl condensation reactions are essential in organic syntheses, as they result in the formation of a carbon-carbon bond, allowing for the construction of complex biomolecules and intermediates as seen in metabolic pathways. 3,4
Specifically, methoxychalcones can be synthesized from the base-catalyzed mixed aldol condensation of acetophenone and a methoxybenzaldehyde, as seen in Scheme 1. 3
"#$%& (
Scheme 1. Synthesis of a methoxychalcone from acetophenone and a methoxybenzaldehyde.
The mechanism for the reversible conversion of 1 equivalent of acetophenone and 1 equivalent of a methoxybenzaldehyde to 1 equivalent of a methoxychalcone is depicted in Scheme 2. As with all mixed aldol condensations between a ketone and an aldehyde, the base-catalyzed Claisen-Schmidt reaction includes the enolate ion of acetophenone reacting with the given aldehyde to form a "- hydroxyketone (an aldol), followed by the dehydration of the aldol to afford an !,"-unsaturated carbonyl. 3 In this experiment, the reversible reaction produces 2-, 3-, or 4-methoxychalcone. 3
Scheme 2. Electron-pushing mechanism for the synthesis of a methoxychalcone via the reversible Claisen-Schmidt reaction. "#$%& ) In the first step, a hydroxide ion from sodium hydroxide serves as a catalyst, deprotonating the acetophenone at a reactive !-hydrogen from the methyl ketone. This converts acetophenone to an anionic form, which tautomerizes to an enolate ion via resonance. Next, this enolate nucleophilically attacks the electrophilic carbonyl carbon of the methoxybenzaldehyde, which also initiates an !- substitution for the acetophenone enolate ion. The resulting anionic tetrahedral intermediate is next protonated by hydroxyl hydrogen from ethanol, resulting in a neutral aldol product (a "-hydroxyketone). In the final step, this aldol is easily dehydrated to yield the final enone product. Specifically, the deprotonated ethanol removes an !-hydrogen from the aldol, forming the alkene and expelling a hydroxide ion as a leaving group via an E1 C B elimination reaction. Subsequently, the hydroxide base catalyst is reformed and a methoxychalcone is produced. 2,3
The purpose of this experiment is to exemplify the synthesis of a biologically significant molecule, a methoxychalcone, from acetophenone and an unknown methoxybenzaldehyde, employing the Claisen-Schmidt mixed aldol condensation. Subsequently, the product can be characterized and identified via melting point, infrared (IR) spectroscopy, 400 MHz 1 H and 100 MHz 13 C nuclear magnetic resonance (NMR) data. 3
II. Experimental 2-Methoxychalcone. Acetophenone (1 mL, 8.573 mmol), ortho-methoxybenzaldehyde (1 mL, 8.278 mmol), and ethanol (95%, 3 mL) were combined and stirred briefly at 25 C. Sodium hydroxide solution (50% by weight, 0.50 mL) was added to the mixture and shaken until a homogenous, cloudy yellow liquid was evident. The reaction mixture was stirred at 5 minute intervals for 30 minutes at 25 C, yielding an orange, layered mixture. The reaction was monitored by TLC (1:1 ethyl acetate/hexanes) until completion, and the crude product was crystallized at -4 C, isolated via vacuum filtration, and washed with deionized water (2 x 3 mL), yielding large, peach-colored crystal aggregates. Recrystallization (70:30 200-proof ethanol/water) afforded 2-methoxychalcone as light yellow, powdery "#$%& * crystals (1.026 g, 52%), mp 51 - 58 C; IR (ATR) # max 2962, 1657, 1594, 1575, 1251 cm -1 ; 1 H NMR (400 MHz, CDCl 3 ) $ (ppm) 8.01 (d, 2H), 7.78 (d, 1H), 7.58 (t, 1H), 7.51 (d, 1H), 7.50 (t, 2H), 7.33 (t, 1H), 7.24 (d, 1H), 7.15 (t, 1H), 6.96 (dd, 1H), 3.85 (s, 3H); 13 C NMR (100 MHz, CDCl 3 ) $ (ppm) 190.44, 159.84, 144.67 138.07, 136.15, 132.73, 129.87, 128.49, 122.26, 121.01, 116.21, 113.33, 99.88, 55.25.
III. Results, Discussion, and Conclusions 2-methoxychalcone was synthesized via the Claisen-Schmidt reaction from acetophenone and ortho-methoxybenzaldehyde starting materials. While Scheme 3 depicts the three possible methoxychalcone products, the synthesized product and unknown aldehyde starting material were identified as such using multiple characterization techniques. This experiment is an important example of a mixed aldol condensation, an important reaction that results in the formation of a carbon-carbon bond, which lends applications in the organic synthesis of complex, biologically significant molecules like chalcones.
Scheme 3. Possible methoxychalcone products, with the product of this synthesis boxed. In the laboratory, the Claisen-Schmidt reaction between acetophenone and ortho- methoxybenzaldehyde was initiated by a sodium hydroxide base catalyst and run at room temperature. TLC monitoring suggested that the reaction had reached completion after 30 minutes, as the reaction lane was found to contain a spot likely indicative of the product (R f =0.59), which was close to that of "#$%& + the acetophenone standard (R f =0.54) due to similar polarities, but far from that of the unknown aldehyde standard (R f =0.42). Since the unknown aldehyde was the limiting reagent in this reaction, this TLC plate indicated that the reaction had reached completion. In the workup, the crude product was cooled and crystallized to allow for easier purification. Next, recrystallization was used as a purification technique to isolate the pure 2-methoxychalcone product from the crude crystals, as the crude product was a suitable solid, containing relatively small amounts of impurities (as indicated by TLC). 70:30 ethanol/water proved to be an effective solvent system, although while heating the product in the solvent, a small amount of oiling out due to product melting may have occurred, as indicated by oil aggregates. These aggregates were pipetted out of the super-saturated solution before slow-cooling began, and did not seem to affect the resulting pure crystals. Thus, the purification by recrystallization was effective, yet not perfect, and may have resulted in some product loss. The percent yield of pure 2-methoxychalcone from this synthesis was found to be 52%. This value is decent, but not ideal, suggesting that some amount of product was lost. Likely, this product loss is due to the purification by recrystallization. This can be inferred due to the crude percent yield, which was found to be 86% before recrystallization, affording 1.688 g of crude crystals, compared to the purified percent yield (52%), affording 1.026 g of purified 2-methoxychalcone. Though the goal of recrystallization is to purify and remove all substances besides the product, it seems that the discarded filtrate may have contained product in addition to impurities, as TLC did not indicate the presence of aldehyde starting material. Additionally, it is much less likely that the product loss is due to the nature of the Claisen-Schmidt reaction. Although this synthesis represented a reversible mixed aldol condensation, the condensation product is heavily favored, especially when water is not present. 4 Since all glassware was dried before use, and the TLC monitoring of the reaction mixture at 30 minutes indicated the absence of limiting reagent (the ortho-methoxybenzaldehyde), it can be assumed that the reaction itself was not significantly responsible for product loss in this synthesis. 3
"#$%& , Despite the below-ideal yield, the purified 2-methoxychalcone was characterized by melting point, IR spectroscopy, 400 MHz 1 H NMR, and 100 MHz 13 C NMR, all of which led to the identification of the product. The purified product had a melting point range of 51-58 C. The literature values for the melting points of 2-, 3-, and 4-methoxychalcone are reported to be 53-57 C, 58-60 C, and 73-76 C, respectively. 3 Therefore, melting point data was not sufficient to identify the product alone, as the broad range reported could be indicative of all of the three possible products if impurities were present. This is because contamination typically leads to melting point depression as the crystalline lattice of the given solid is disrupted, requiring a lower temperature to melt the substance. 3
The purified crystals from this synthesis were then characterized by IR spectroscopy, which provided strong evidence of a methoxychalcone, but not enough information to identify the specific product or entirely rule out the presence of starting materials (Supplemental Information, Figure 1). Beginning with the carbon-hydrogen stretch, the peak occurring at 2962 cm -1 and those close to this peak are indicative of the aromatic carbon-hydrogen bonds and the carbon-vinylic hydrogen bond of an alkene functionality. Importantly, the peak at 1657 cm -1 is likely indicative of a carbon-oxygen double bond that would occur in a carbonyl functionality such as a conjugated ketone in 2-methoxychalcone. In the carbon-hydrogen bending region of the IR spectrum, the peaks at 1594 cm -1 and 1575 cm -1 are likely indicative of the carbon-carbon double bonds in alkene functionalities, such as those that would occur in an aromatic ring or in other alkenes. Lastly, the peak at 1251 cm -1 likely corresponds to the carbon- oxygen single bond due to an aryl ether functionality, such as might occur due to the methoxy group in 2-methoxychalcone. The presence of these functional groups provides evidence that a methoxychalcone could have been synthesized, due to the presence of peaks indicative of carbon-hydrogen aromatic/alkene bonding, carbon-oxygen carbonyl bonding, carbon-carbon alkene bonding, and an carbon-oxygen bonding due to an ether function. 3 However, all of these peaks would also be present in the starting materials acetophenone and a methoxybenzaldehyde, so the IR spectroscopy data does not absolutely suggest specific product formation. "#$%& - The 400 MHz 1 H NMR spectrum (Supplemental Information, Figures 2a-c) for the synthesized crystals is very important for the identification of the purified product as 2-methoxychalcone, as opposed to 3- or 4-methoxychalcone. This data also refutes the notion that starting material was present in the purified product. Peaks corresponding to 10 unique hydrogens were integrated. Importantly, many of the hydrogen peaks are shifted downfield, out of the expected range due to the significant conjugation in the methoxychalcone molecules. Beginning with the most downfield peaks, the doublet at 8.01 ppm with an integration value of 2 is suspected to designate the two hydrogens in the aromatic ring that are in the ortho position to the carbon that is bonded to the ketone functionality. The doublet at 7.78 ppm with an integration value of 1 is likely due to the vinylic hydrogen around the enone alkene of the methoxychalcone that is closer to the carbon-oxygen carbonyl double bond. This is shifted further downfield by the oxygen than the peaks due to the other vinylic hydrogen, which likely appear at 7.51 ppm as a doublet with an integration value of 1, and are clearly coupled with the former vinylic hydrogen peaks. The latter vinylic hydrogen doublet peaks overlap with a triplet (7.50 ppm, integration value of 3), that likely represent the two aromatic hydrogens that are in the meta position to the carbon that is bonded to the ketone functionality. The remaining peaks in the aromatic region (7.58 ppm (t, 1H), 7.33 ppm (t, 1H), 7.24 ppm (d, 1H), 7.15 ppm (t, 1H), 6.96 ppm (dd, 1H)) are difficult to identify due to complex splitting, and are not significant for product identification. Lastly, the singlet occurring at 3.85 ppm with an integration value of 3 is likely indicative of the methyl group from the methoxy functionality in the methoxychalcone product. While all of the discussed peaks would be evident in NMR spectra for each of the possible methoxychalcone products, 4-methoxychalcone can be ruled out based on this data because 10 unique hydrogens were integrated. In 2- or 3-methoxychalcone, there are 10 unique proton types, yet in 4- methoxychalcone, there are only 8 unique protons due to additional symmetry in the second aromatic ring. Importantly, 3-methoxychalcone can also be ruled out based on splitting patterns. In 3- "#$%& . methoxychalcone, there would likely be a singlet with an integration value of 1 somewhere in the 1 H NMR spectrum, due to the aromatic hydrogen that is in the ortho position to the carbon that is bonded to the methoxy functionality and the carbon that is bonded to the enone functionality. Additionally, there is no evidence of starting material in this spectrum, as there is no singlet in the 9.0-10.0 ppm range that would be indicative of an aldehyde proton (from a methoxybenzaldehyde) nor a singlet in the 2.1-2.4 ppm range that would be indicative of a methyl ketone (from acetophenone). Thus, the 1 H NMR strongly suggests that 2-methoxychalcone was synthesized without the presence of starting materials acetophenone or ortho-methoxybenzaldehyde. 3
The 100 MHz 13 C NMR spectrum (Supplemental Information, Figure 3) for the synthesized product also provides confirmation that 2-methoxychalcone was synthesized, though it cannot rule out 3-methoxychalcone as a product without the 400 MHz 1 H NMR data. There are 14 peaks in the spectrum, while there are 16 carbons in each methoxychalcone. The number of peaks is consistent with the structure of both 2-methoxychalcone and 3-methoxychalcone, which both have equivalent carbons ortho and meta to the carbonyl group. However, the number of peaks is not consistent with the structure of 4-methoxychalcone, eliminating it as an option because it has symmetry on both aromatic rings, lending only 12 unique carbons. Beginning with the high chemical shift end of the spectrum, the peak at 190.44 ppm is likely indicative of the carbonyl carbon. The peak at 159.84 ppm is likely due to the aromatic carbon that is bonded to the methoxy oxygen in a methoxychalcone, as this proximity to a heteroatom would shift the peak downfield. The remaining 11 peaks in the aromatic region are not easily identifiable, yet are not significant to product identification in this case. Lastly, the peak at 55.25 ppm likely corresponds to the methyl carbon in the methoxy group of methoxychalcones. Therefore, 13 C NMR is useful for collectively suggesting the presence of 2-methoxychalcone with other forms of data. 3
In conclusion, this experiment was successful in achieving the purpose. The biologically significant molecule 2-methoxychalcone was synthesized and identified from three product possibilities "#$%& /0 via the Claisen-Schmidt reaction with acetophenone and ortho-methoxybenzaldehyde starting materials. 3
The melting point, IR, 400 MHz 1 H NMR, and 100 MHz 13 C NMR data collectively provide strong evidence that 2-methoxychalcone was the synthesized product, without evidence of impurities and a decent percent yield of 52%. Evidently, there were several sources of error in this laboratory that may have led to the less than ideal percent yield, although the results were respectable. Since product loss due to the nature of the Claisen-Schmidt reaction itself is not likely, and the reaction went to completion according to TLC, it seems that product was indeed lost during the purification step (recrystallization). This may have occurred due to the slight oiling out that was evident, indicating that some of the product in solution may have melted if the solvent temperature was too high. Further, slow cooling may not have been conducted slowly enough or at a cool enough temperature. To solve this issue, a more precise recrystallization technique could have been employed, with extended cooling time or reduced temperature (refrigeration). Additionally, a second crop of crystals could have been recrystallized using the primary filtrate from the first crop, although this crop would be more likely to include impurities. Moreover, as opposed to using recrystallization as a purification method, column chromatography could have been used, and may have avoided the complications associated with recrystallization. 3 These improvements would likely augment the purified percent yield of 2-methoxychalcone in the experiment. Despite these drawbacks, this laboratory was successful in both exemplifying the increasingly pertinent Claisen-Schmidt synthesis of a chalcone, and in synthesizing an unknown product for identification. Formation of pure 2-methoxychalcone with an acceptable percent yield was confirmed by various characterization techniques. As the broad applications of pharmaceutically active chalcones are further appreciated and explored, syntheses such as this one will become increasingly relevant. In future, it is likely that researchers will strive to produce less toxic, more efficient chalconoids. 1,2
"#$%& // IV. References (1) Batovska, D. I.; Todorova, I. T. J. Current Clinical Pharmacology. 2013, 5, 1-29. (2) Rahman, M.A. Chem. Sci. J. 2011, 29, 1-16. (3) Wink, D.; Angelo, N. G.; Henchey, L. K.; Waxman, A. J.; Canary, J. W.; Arora, P. S. J. Chem. Educ. 2007, 84, 1816-1818. (4) Hathaway, B.A. J. Chem. Educ. 1987, 64, 367-368.