Professional Documents
Culture Documents
Medical Laboratory
Medical Laboratory
Medical Laboratory
LABORATORY
1
A clinical medical test laboratory where blood tests, ECG, CT scanning, physiotherapy, etc
are performed.
MEDICAL TESTS:
Haemotology tests
Biochemical tests
Microbiological tests
Urine tests
Endocrine tests
Motion tests
Semen analysis
FACILITIES AVAILABLE:
Electronic Traction
Ultra sound
Wax Bath
T.E.N.S
Cryotherapy
Stimulator(Muscle/Nerve)
Exercise therapy 1
Manipulation therapy
Page | 2 Neuro Development therapy
Chest Physiotherapy
Sports Physiotherapy
Combination therapy
EQUIPMENTS SEEN:
Electrocardiogram
Stimulator
Traction table
IFT
Ultrasound technology
Shortwave diathermy
Auto analyser
Incubator
ELECTROCARDIOGRAPHY
Timed interpretation of an ECG was once incumbent to a stylus and paper speed.
Computational Analysis now allows considerable study of Heart Rate Variability. A typical
electrocardiograph runs at a paper speed of 25 mm/s, although faster paper speeds are
occasionally used. Each small block of ECG paper is 1 mm². At a paper speed of 25 mm/s, one
small block of ECG paper translates into 0.04 s (or 40 ms). Five small blocks make up 1 large
block, which translates into 0.20 s (or 200 ms). Hence, there are 5 large blocks per second. A
diagnostic quality 12 lead ECG is calibrated at 10 mm/mV, so 1 mm translates into 0.1 mV. A
calibration signal should be included with every record. A standard signal of 1 mV must move
the stylus vertically 1 cm, that is two large squares on ECG paper.
1
WAVES AND INTERVALS
Page | 4
A typical ECG tracing of a normal heartbeat (or cardiac cycle) consists of a P wave, a
QRS complex and a T wave . A small U wave is normally visible in 50 to 75% of ECGs. The
baseline voltage of the electrocardiogram is known as the isoelectric line. Typically the
isoelectric line is measured as the portion of the tracing following the T wave and preceding the
next P wave.
The four deflections were originally named ABCDE but renamed PQRST after correction
for artifacts introduced by early amplifiers.
Page | 5
CT SCAN TECHNOLOGY
CT scans of internal organs, bone, soft tissue and blood vessels provide greater clarity and
reveal more details than regular x-ray exams.
Using specialized equipment and expertise to create and interpret CT scans of the body,
radiologists can more easily diagnose problems such as cancers, cardiovascular disease,
infectious disease, trauma and musculoskeletal disorders.
quickly identify injuries to the lungs, heart and vessels, liver, spleen, kidneys, bowel or
other internal organs in cases of trauma.
guide biopsies and other procedures such as abscess drainages and minimally invasive
tumor treatments.
plan for and assess the results of surgery, such as organ transplants or gastric bypass.
stage, plan and properly administer radiation treatments for tumors as well as monitor
response to chemotherapy.
measure bone mineral density for the detection of osteoporosis.
DESCRIPTION:
The CT scanner is typically a large, box like machine with a hole, or short tunnel, in the 1
center. You will lie on a narrow examination table that slides into and out of this tunnel. Rotating
around you, the x-ray tube and electronic x-ray detectors are located opposite each other in a
Page | 6 ring, called a gantry. The computer workstation that processes the imaging information is located
in a separate room, where the technologist operates the scanner and monitors your examination.
PROCEDURE:
Next, the table will move quickly through the scanner to determine the correct starting
position for the scans. Then, the table will move slowly through the machine as the actual CT
scanning is performed.
You may be asked to hold your breath during the scanning. Any motion, whether
breathing or body movements, can lead to artifacts on the images. This is similar to the blurring
seen on a photograph taken of a moving object.
When the examination is completed, you will be asked to wait until the technologist
verifies that the images are of high enough quality for accurate interpretation.
LIMITATIONS:
Soft-tissue details in areas such as the brain, internal pelvic organs, knee or shoulder can
be more readily and clearly seen with magnetic resonance imaging (MRI). The exam is not
generally indicated for pregnant women.
A person who is very large may not fit into the opening of a conventional CT scanner or may
be over the weight limit for the moving table
1
BENEFITS:
Page | 7
CT scanning is painless, noninvasive and accurate.
A major advantage of CT is its ability to image bone, soft tissue and blood vessels all at
the same time.
Unlike conventional x-rays, CT scanning provides very detailed images of many types of
tissue as well as the lungs, bones, and blood vessels.
CT examinations are fast and simple; in emergency cases, they can reveal internal
injuries and bleeding quickly enough to help save lives.
CT has been shown to be a cost-effective imaging tool for a wide range of clinical
problems.
CT is less sensitive to patient movement than MRI.
CT can be performed if you have an implanted medical device of any kind, unlike MRI.
CT imaging provides real-time imaging, making it a good tool for guiding minimally
invasive procedures such as needle biopsies and needle aspirations of many areas of the
body, particularly the lungs, abdomen, pelvis and bones.
A diagnosis determined by CT scanning may eliminate the need for exploratory surgery
and surgical biopsy.
No radiation remains in a patient's body after a CT examination.
X-rays used in CT scans usually have no side effects.
RISKS:
There is always a slight chance of cancer from excessive exposure to radiation. However,
the benefit of an accurate diagnosis far outweighs the risk.
The effective radiation dose from this procedure ranges from approximately two to 10
mSv, which is about the same as the average person receives from background radiation
in three to five years.
Women should always inform their physician and x-ray or CT technologist if there is any
possibility that they are pregnant.
CT scanning is, in general, not recommended for pregnant women unless medically
necessary because of potential risk to the baby.
Nursing mothers should wait for 24 hours after contrast material injection before
resuming breast-feeding.
1
The risk of serious allergic reaction to contrast materials that contain iodine is extremely
rare, and radiology departments are well-equipped to deal with them.
Page | 8 Because children are more sensitive to radiation, they should have a CT study only if it is
essential for making a diagnosis and should not have repeated CT studies unless
absolutely necessary.
SUGGESTIONS:
MADHAVARAM .
Most dairy farms sell the male calves born by their cows, usually for veal production, or
breeding depending on quality of the bull calf, rather than raising non-milk-producing stock.
Many dairy farms also grow their own feed, typically including corn, alfalfa, and hay. This is fed
directly to the cows, or is stored as silage for use during the winter season. Additional dietary
supplements are often added to the feed to increase quality milk production.
Dairy farming has been part of agriculture for thousands of years. Historically it has been
one part of small, diverse farms. In the last century or so larger farms doing only dairy
production have emerged. Large scale dairy farming is only viable where either a large amount
of milk is required for production of more durable dairy products such as cheese, or there is a
substantial market of people with cash to buy milk, but no cows of their own.
HAND MILKING
MILKING PARLORS
The milking parlor allowed a concentration of money into a small area, so that more
technical monitoring and measuring equipment could be devoted to each milking station in the
parlor. Rather than simply milking into a common pipeline for example, the parlor can be
equipped with fixed measurement systems that monitor milk volume and record milking
statistics for each animal. Tags on the animals allow the parlor system to automatically identify
each animal as it enters the parlor.
ROTARY PARLORS
In rotary parlors, the cows are loaded one at a time onto the platform as it slowly rotates.
The milker stands near the entry to the parlor and puts the cups on the cows as they move past.
By the time the platform has completed almost a full rotation, another milker or a machine
removes the cups.
MILKING OPERATION
Milking machines are held in place automatically by a vacuum system that draws the 1
ambient air pressure down from 15 to 21 pounds of vacuum. The vacuum is also used to lift milk
vertically through small diameter hoses, into the receiving can. A milk lift pump draws the milk
Page | 11 from the receiving can through large diameter stainless steel piping, through the plate cooler,
then into a refrigerated bulk tank.
Milk is extracted from the cow's udder by flexible rubber sheaths known as liners or
inflations that are surrounded by a rigid air chamber. A pulsating flow of ambient air and
vacuum is applied to the inflation's air chamber during the milking process. When ambient air is
allowed to enter the chamber, the vacuum inside the inflation causes the inflation to collapse
around the cow's teat, squeezing the milk out of teat in a similar fashion as a baby calf's mouth
massaging the teat. When the vacuum is reapplied in the chamber the flexible rubber inflation
relaxes and opens up, preparing for the next squeezing cycle.
It takes the average cow three to five minutes to give her milk. Some cows are faster or
slower. Slow-milking cows may take up to fifteen minutes to let down all their milk. Milking
speed is only minorly related to the quantity of milk the cow produces — milking speed is a
separate factor from milk quantity; milk quantity is not determinative of milking speed. Because
most milkers milk cattle in groups, the milker can only process a group of cows at the speed of
the slowest-milking cow. For this reason, many farmers will cull slow-milking cows.
The extracted milk passes through a strainer and plate heat exchangers before entering
the tank, where it can be stored safely for a few days at approximately 3 °C or around 42 °F
(6 °C). At pre-arranged times, a milk truck arrives and pumps the milk from the tank for
transport to a dairy factory where it will be pasteurized and processed into many products.
PROCESSING OF MILK:
Raw milk is brought to the dairy plant, it is then graded, weighed, and sampled. The
butterfat content determines the price paid the farmer.
Processing of raw milk starts with clarification or separation, using centrifuges.
The clarification process removes impurities like blood cells from the milk that will be
sold as whole milk (milk containing all of its butterfat). Separation process removes
butterfat as well as impurities from milk. Skim milk is produced when all the butterfat is
removed from the raw milk.
Dairy cows are milked 2 or 3 times a day. Most dairy farms use milking machines. The
fresh milk is strained through cotton to remove foreign matters, it is then cooled in the
milk house and then sold in bulk form to dairy plants. Milk is shipped by truck in 10- 1
gallon cans or in refrigerated tank trucks.
Page | 12
Milk is then pasteurized to kill harmful bacteria.
Milk with butterfat is then homogenized to prevent the butterfat from separating from the
milk.
Processed milk is then chilled in a cooler and then placed in sterile containers.
Processed milk is then packed individually in containers, which are usually plastic bottles
or paper cartons, are put on moving racks and pass under machine that will automatically
fills and seals them.
Homogenization - is the process of breaking up the fat into smaller sizes so that it no longer
separates from the milk.
Pasteurization - is the process of heating liquid for the purpose of destroying viruses and harmful
organism. It is different from sterilization because pasteurization only aims to reduce the number
of bacteria so they are unlikely to cause disease. Sterilization is not common in food processing
because it can affect the flavor.
MEDICAL CARE
During milking dairy farmers and their employees are constantly checking and
monitoring their animals. Nutritious diets, comfortable living conditions and solid medical care
are all part of taking good care of their animals. This includes regular veternarian check-ups
across the entire farm, either monthly, bi-monthly or, on some farms, weekly, to keep an eye on
the wellness of the herd. Vaccinations and prompt treatment of illnesses are among the many
practices used by dairy farmers to ensure healthy herds.
Cows are no different than people in that they sometimes become ill and require medical
care. Farmers work with large-animal veterinarians who can diagnose and treat an illness with
the proper medication. Any cows who receive medicine to aid in a speedy recovery are removed
from the healthy herd and won’t rejoin their herdmates until their milk tests free of antibiotics.
Milk that tests positive for antibiotics is not permitted in the food supply and is immediately
discarded.
1
Page | 13
CLEANING EFFICIENCY:
W-Water quality;soft,hard water hinders the action of detergents may leave behind mineral
residue.
A-Agitation of the detergent solution should be vigorous, detergent flow velocity should be
T- Time of detergent solution contact with the soil of surface should be adequate.It
DAIRY PRODUCTS:
Butter, Cream, Cottage cheese, Yogurt, Yogurt drinks, flavoured milk drinks and
Ice-creams.
1
India is the largest producer of dairy products in the world. There is a great deal of variation
in the pattern of dairy production world-wide. Many countries which are large producers,
Page | 14 consume this internally, while others — in particular New Zealand — export a large percentage
of their production. Internal consumption is often in the form of liquid milk, while the bulk of
international trade is in processed dairy products such as milk powder.
The world's largest exporter of dairy products is New Zealand,and dairy products are the largest
export earner for the country.Fonterra is the fifth-largest dairy company in the world and New
Zealand's largest company by turnover,
World production
1 India 114.4
3 Germany 39.4
4 Pakistan 35.2
5 China 32.5
6 Russia 28.5
7 Brazil 26.2
1
8 France 24.2
Page | 15
11 Ukraine 12.2
12 Poland 12
13 Netherlands 11.5
14 Italy 11.0
15 Turkey 10.6
16 Mexico 10.2
17 Australia 9.6
18 Egypt 8.7
19 Argentina 8.5
20 Canada 8.1
COMPETITION
Most milk-consuming countries have a local dairy farming industry, and most producing
countries maintain significant subsidies and trade barriers to protect domestic producers from
foreign competition. In large countries, dairy farming tends to be geographically clustered in 1
regions with abundant natural water supplies (both for feed crops and for cattle) and relatively
inexpensive land (even under the most generous subsidy regimes, dairy farms have poor return
Page | 16 on capital). New Zealand, the fourth largest dairy producing country, does not apply any
subsidies to dairy production.
The milking of cows was traditionally a labor-intensive operation and still is in less
developed countries. Small farms need several people to milk and care for only a few dozen
cows, though for many farms these employees have traditionally been the children of the farm
family, giving rise to the term "family farm".
Advances in technology have mostly led to the radical redefinition of "family farms" in
industrialized countries such as the United States. With farms of hundreds of cows producing
large volumes of milk, the larger and more efficient dairy farms are more able to weather severe
changes in milk price and operate profitably, while "traditional" very small farms generally do
not have the equity or cash flow to do so. The common public perception of large corporate
farms supplanting smaller ones is generally a misconception, as many small family farms expand
to take advantage of economies of scale, and incorporate the business to limit the legal liabilities
of the owners and simplify such things as tax management.
Before large scale mechanization arrived in the 1950s, keeping a dozen milk cows for the
sale of milk was profitable. Now most dairies must have more than one hundred cows being
milked at a time in order to be profitable, with other cows and heifers waiting to be "freshened"
to join the milking herd . In New Zealand the average herd size, depending on the region, is
about 350 cows.
Herd size in the US varies between 1,200 on the West Coast and Southwest, where large
farms are commonplace, to roughly 50 in the Northeast, where land-base is a significant limiting
factor to herd size. The average herd size in the U.S. is about one hundred cows per fa