Professional Documents
Culture Documents
Reostate Pape&Olbertz
Reostate Pape&Olbertz
Reostate Pape&Olbertz
=
PAPE & OLBERTZ
SCHALTGERTE UND WIDERSTNDE GMBH
6
III. Starter description
A starter OADAK, ODAS consists of:
oil tank with oil level indicator and outlet valve
a compartment with a resistor-part and contact-drum (OADAK) fastening under a
lid
the control (and power contactors for ODAS) and the rotor cable terminal block is
on top of the lid under a sheet-steel hood or in a switch-cabinet
the resistor-part consists of only AEG-Resistor grids
protection class IP 54
the 2-K paint corresponds to RAL 7032; other colours on request
Control voltage: 3 x 400 V, 50 Hz and 230 V, 50 Hz or
3 x 440 V, 60 Hz and 230 V, 60 Hz ;
other voltages on request.
a remote control and also an emergency handwheel (OADAK)
thermostat F3 and F31 (and F4 for OADAK 4..U to OADAK 8) for temperature
monitoring
step-time-monitor (OADAK)
oil-circulating pump for OADAK 4...U to OADAK 8...
contacts tungsten-tipped (for h > 2 or P > 3000 kW)(OADAK)
Additional equipment:
auxiliary switches
thermostat
anti-condensation-heater
oil-level-switch
locked-rotor-control (rotor frequency control)
cable glands for rotor cable and control cable
FLS-packet: contactor, auxiliary switches, cable glands, anti-condensation-heater
and control transformer
for raising the periodic starts h , cooling fins or radiators
PAPE & OLBERTZ deliver the starter without oil-filling and stator switch gear!
PAPE & OLBERTZ
SCHALTGERTE UND WIDERSTNDE GMBH
7
IV. Instructions for selecting oil-cooled rheostatic starter OADAK
(drum type) / ODAS (contactor-type)
The size of the starter must be selected to the motor characteristics (P, I
er
, U
er
) and the
starting characteristics (f, t
a
, z, W and h). The characteristics specified in the tables are
maximum values and these values must not exceed without to contact Pape & Olbertz.
1. Selecting a drum-type oil-cooled rheostatic starter type OADAK:
The former has three possibilities for a calculation/selection:
a. calculation of the starting energy W selection the size in table 1.1 with the
heat capacity;
b. selection with the data P and f the starter size in table 1.1 in view of the
starting time t
a
;
c. selection with the data P and the drive application in table 1.2.
Example:
Application: Ball-mill (f = 1.3)
P = 2000 kW
I
er
= 960 A
t
a
= 18 s
z = 3
h = 1
a. W = 0.5 P f z t
a
= 70200 kWs ,
with this heat capacity in table 1.1 the starter size is OADAK 54..
b. With the information of the power P and the starting severity f = 1,4 the
correct starter size according to the table 1.1 and a longer starting time
t
a
= 32 sec is OADAK 64..
c. With the application Ball-mill drive and the rated motor power P you will
also find the starter size OADAK 64.. in table 1.2 .
Now you can select the standard starter size with the rotor current of 1120 A in
table 1.3. You need the 1200 A size, so that the starter size is now OADAK 5412
or OADAK 6412.
PAPE & OLBERTZ
SCHALTGERTE UND WIDERSTNDE GMBH
8
You'll find all technical data in the column for the size in table 1.1. You'll also
find the number for the dimension drawing and the control wiring number of the
standard execution.
By example the data for OADAK 6412:
z = 3; h = 0,35; weight = 1000 kg and you need 1360 ltr. Oil.
But for these example you need h = 1. You'll find the data and the extension for
the starter size in table 1.1 and table1.2 in the columns under size for h = 1.
The starter size is now OADAK 64 12 R14. The starter needs a tank with
radiators (14 elements).
For an execution for h = 2:
with table 1.8 and the size OADAK 6... you select the radiators size R 28 with
the coefficient 5.8. The price is shown in the same row.
The starter size is now OADAK 6412 R28.]
The selection/calculation for the sizes OADAK 1.. to 4...U is the same, but you
need cooling fins (table 1.7).
Tip:
Select the motor with the lowest rotor current!
71 . 5
35 , 0
2
h
h
a
set
real
= = =
PAPE & OLBERTZ
SCHALTGERTE UND WIDERSTNDE GMBH
9
2. Selecting a contactor-type oil-cooled rheostatic starter type ODAS:
The former has two possibilities for a calculation/selection:
a. calculation of the starting energy W selection the size in table 1.4 with the
heat capacity;
b. selection with the data P and f the starter size in table 1.4.
Example:
P = 300 kW
I
er
= 365 A
f = 1
t
a
= 15 s
z = 3
h = 1
a. W = 0.5 P f z t
a
= 6750 kWs ,
with the heat capacity in table 1.4 the starter size is ODAS 24-...
b. With the rated power of the motor P and the start severity f you'll also find
the starter size ODAS 24-... in table 1.4 .
Now you can select the standard starter size with the rotor current of 365A in
table 1.5. You need the 370 A size, so that the starter size is now ODAS 24-
370/6.
You'll find all technical data in the column for the size in table 1.4. You'll find
also the number for the dimension drawing of the standard execution.
Data for ODAS 24-370/6:
z = 3; h = 1,2; weight = 125 kg and you need 100 ltr. Oil.
For an execution for h = 2:
with table 1.7 and the size ODAS 2... you select the fins size R 1 with the
coefficient 2.
Tip:
Select the motor with the lowest rotor current!
67 . 1
2 . 1
2
h
h
a
set
real
= = =
PAPE & OLBERTZ
SCHALTGERTE UND WIDERSTNDE GMBH
10
V. Conditions of sale and delivery
The standard term of delivery is ex works, excluding packing, excluding customs fees
and import taxes. Other terms on request.
Pape & Olbertz deliver the starter without oil-filling and stator switch-gear.
Pape & Olbertz reserve the right to adjust the prices and the technical data. The prices
base on buying one unit, for more units ask Pape & Olbertz for other conditions.
PAPE & OLBERTZ
SCHALTGERTE UND WIDERSTNDE GMBH
11
Appendix A.: Dimension drawings MZ..
MZ 1495
MZ 1507
MZ 1553
MZ 1556
MZ 1571
MZ 1614
MZ 1615
MZ 1630
MZ 1631
MZ 1632
MZ 1633
MZ 1634
MZ 1691
MZ 1693
MZ 1695
MZ 1704
MZ 1721
MZ 1733
MZ 1760
MZ 1761
MZ 1830
PAPE & OLBERTZ
SCHALTGERTE UND WIDERSTNDE GMBH
12
Appendix B.: Standard wiring diagram (SF..) for starter type
OADAK
SF 120
SF 158
SF 167
PAPE & OLBERTZ
SCHALTGERTE UND WIDERSTNDE GMBH
13
Appendix C.: Example wiring diagram for starter type ODAS
S 1 DAS 117
PAPE & OLBERTZ
SCHALTGERTE UND WIDERSTNDE GMBH
14
Appendix D.: Project-sheet for a rheostatic-starter calculation
For a calculation of a rheostatic starter Pape & Olbertz need the following data:
Rated motor power P [kW] (X):
Rotor voltage at standstill U
er
[V] :
Rotor current at full load I
er
[A] (X):
Rated motor speed n
n
[rpm]:
Motor pull-out torque:
Total moment of inertia related to motor
speed GD [kpm]:
Type of driven machine (X):
Load torque plotted against speed:
Number of consecutive starts z:
Permissible number of starts per hour h:
The starter do you need for your drive can Pape & Olbertz now exactly calculate with
these data.
For the first step at a project Pape & Olbertz need only the data marked with (X).
If you have any questions referring to calculation, technology or other products of our
delivery scope, please contact our technical department
Herr Legrand Tel. + 49(0)2233/96337-33
Herr Althaus Tel. + 49(0)2233/96337-34
Herr Bauer Tel. + 49(0)2233/96337-31
Phone: ++49-(0)2233-96337-0
FAX: ++49-(0)2233-96337-60
Mail: po@pape-olbertz.de