This document provides specifications for round head tension control structural bolts according to ASTM F2280 Type 1. It lists dimensional requirements for bolt size, length, diameter, thread length and other characteristics. Any bolts received must meet these standards or it could result in corrective action for the supplier. Material properties and mechanical testing must also adhere to specifications for heavy hex structural bolts, nuts and washers.
This document provides specifications for round head tension control structural bolts according to ASTM F2280 Type 1. It lists dimensional requirements for bolt size, length, diameter, thread length and other characteristics. Any bolts received must meet these standards or it could result in corrective action for the supplier. Material properties and mechanical testing must also adhere to specifications for heavy hex structural bolts, nuts and washers.
This document provides specifications for round head tension control structural bolts according to ASTM F2280 Type 1. It lists dimensional requirements for bolt size, length, diameter, thread length and other characteristics. Any bolts received must meet these standards or it could result in corrective action for the supplier. Material properties and mechanical testing must also adhere to specifications for heavy hex structural bolts, nuts and washers.
Round Head Tension Control Structural Bolts, ASTM F2280, Type 1, Assembled The information below lists the required dimensional, chemical and physical characteristics of the fasteners in this purchase order. If the order received does not meet these requirements, it may result in a supplier corrective action request, which could jeopardize your status as an approved vendor. Unless otherwise specified, all referenced consensus standards must be adhered to in their entirety.
D LT LS S Max. Min. Max. Basic Max. Min. 1/2" 0.515 0.482 1.126 5/16 0.323 0.302 Ref. 0.50 0.32 5/8" 0.642 0.605 1.313 25/64 0.403 0.378 1.25 0.60 0.43 3/4" 0.768 0.729 1.580 15/32 0.483 0.455 1.38 0.65 0.53 7/8" 0.895 0.852 1.880 35/64 0.563 0.531 1.50 0.72 0.61 1" 1.022 0.976 2.158 39/64 0.627 0.591 1.75 0.80 0.70 1 1/8" 1.149 1.098 2.375 11/16 0.718 0.658 2.00 0.80 0.80 E Nominal Size (inch) Length of Spline Ref. Width Across Flats Spline Ref Head Dia. H Head Height Thread Length Basic Full Size Body Dia.
Max. Min. Max. Min. Max. Min. 1/2 .875 .850 1.010 .969 .504 .464 5/8 1.062 1.031 1.227 1.175 .631 .587 3/4 1.250 1.212 1.443 1.382 .758 .710 7/8 1.438 1.394 1.660 1.589 .885 .833 1 1.625 1.575 1.876 1.796 1.012 .956 1 1/8 1.812 1.756 2.093 2.002 1.139 1.079 Nominal Size F G H Width Across Flats Width Across Corners Thickness
Page 2 of 2 Fastenal Product Standard REV-01 Date: February 13, 2012
TCSB.F2280.ASMBL.P
B A Nominal Nominal Min. Max. 1/2 1.063 .531 .097 .177 5/8 1.313 .688 .122 .177 3/4 1.468 .813 .122 .177 7/8 1.750 .938 .136 .177 1 2.000 1.063 .136 .177 1 1/8 2.250 1.188 .136 .177 C Size
Specification Requirements: Dimensions: ASME B18.2.6. Material & Mechanical Properties: Heavy Hex Structural Bolt: ASTM F2280, Type 1. Heavy Hex Nut: ASTM A563 Grade DH. Structural Washer: ASTM F436. Thread requirements: ASME B1.1 UNC Class 2A. Head marking: Must have A490TC and manufacturer ID. Coating: Light protective oil. Material Test Reports: The MTR must have documented lot traceability, including full chemical and mechanical figures, to the specification(s) above.