This document provides step-by-step instructions for creating a basic PLC program using Unity Pro XL software that controls an output relay based on the status of "Start" and "Stop" input bits. The program involves: 1) Creating a new project and configuring I/O modules, 2) Programming a ladder logic routine using contacts and coils, 3) Assigning tags to represent the I/O bits, 4) Downloading and simulating the program on a PLC, 5) Creating an operator interface with pushbuttons to control the "Start" and "Stop" bits. The program demonstrates how the relay output is turned on and off based on the status of the input bits.
This document provides step-by-step instructions for creating a basic PLC program using Unity Pro XL software that controls an output relay based on the status of "Start" and "Stop" input bits. The program involves: 1) Creating a new project and configuring I/O modules, 2) Programming a ladder logic routine using contacts and coils, 3) Assigning tags to represent the I/O bits, 4) Downloading and simulating the program on a PLC, 5) Creating an operator interface with pushbuttons to control the "Start" and "Stop" bits. The program demonstrates how the relay output is turned on and off based on the status of the input bits.
This document provides step-by-step instructions for creating a basic PLC program using Unity Pro XL software that controls an output relay based on the status of "Start" and "Stop" input bits. The program involves: 1) Creating a new project and configuring I/O modules, 2) Programming a ladder logic routine using contacts and coils, 3) Assigning tags to represent the I/O bits, 4) Downloading and simulating the program on a PLC, 5) Creating an operator interface with pushbuttons to control the "Start" and "Stop" bits. The program demonstrates how the relay output is turned on and off based on the status of the input bits.
Schneider Electric Thailand Automation Solution 2 Choose Unity Pro XL 3 Program active 4 Create new PLC program 5 Choose PLC type 6 Project creating 7 Choose Hardware config (double click) 8 Existing PLC with blank I/O 9 Double click slot No. 1 10 Choose 16 Input module 11 Choose another slot 12 Choose 16 Output module 13 Click to close Hardware catalog 14 Start MAST task (click) 15 Select section 16 Right click to create new section 17 Choose LD ( Ladder ) 18 Apply section name 19 Click OK 20 New section programming area 21 Click to close PLC bus 22 Click to close Project Browser 23 Click to enlarge Programming area 24 Ready to programming 25 Choose NO contact ---| |--- 26 Click to place contact on any location 27 Choose NC contact ---|/|--- 28 Choose Output ---( )--- 29 Place on any location in 1 st row 30 Choose vertical line 31 Connect vertical line 32 Change mouse back to pointer 33 Double click to assign tag 34 Assigned Start tag 35 Choose BOOL 36 Accept change 37 Assign Stop tag 38 Assign Relay tag 39 Double click to assign tag 40 Choose existing tag 41 Choose Relay tag 42 OK to confirm 43 Analyze project 44 Analyze report 45 Rebuild project 46 Rebuild report 47 Connect to PLC Simulation Mode 48 PLC status program difference 49 Download program 50 Transfer confirm 51 Transferring 52 Transfer complete 53 Place PLC in RUN 54 PLC RUN Confirm 55 PLC RUN 56 Right click on Start bit set 1 57 Start bit active 58 Right click on Start bit set 0 59 Start bit OFF 60 Right click on Stop bit set 1 61 Stop bit active 62 Bit status monitor (drag mouse cover monitor bits) 63 Bit monitoring showing up 64 Right click then choose Table 65 Animation table show bit status 66 Show multiple windows 67 Monitor both Ladder & Table 68 Choose Modification 69 Right click on modify bit, set to 0 70 Stop bit Inactive 71 Select Start bit and set value to 1 72 Start bit Active->Relay bit 73 Reset Start bit 74 Start bit Inactive but Relay still Active 75 Set Stop bit 76 Stop bit Active->Relay bit Inactive 77 Reset Stop bit 78 Stop bit Inactive 79 Open Project Browser to create Operator screen 80 Right click to create new screen 81 Apply screen name and click ok 82 Screen area 83 Choose Push Button 84 Place on location 85 Select and right click to Copy Button 86 Right click and paste 87 Drag to desired location 88 Choose Text 89 Place on location 90 Copy text 91 Paste 92 Text Done 93 Double click to config button 94 Choose tag and ok 95 Tag assign done 96 Assign another tag 97 OK 98 Config text with Relay ON 99 Choose REDcolor 100 Choose animated object 101 Choose Relay tag 102 Show when bit = 1 103 Choose Standard display 104 Config Text 2 with Relay OFF 105 Choose Green 106 Choose animated object 107 Choose Relay tag 108 Show when bit = 0 109 Choose Standard display 110 Rearrange screen 111 Add 1 st Button label 112 Add 2 nd Button label 113 Operator screen ready to test 114 Start graphic monitor 115 Press Start 116 Relay ON 117 Press Stop 118 Relay OFF 119 Save work 120 Enter file name 121 Finish saving 122 Exit program 123 Confirm to exit 124 Thank you