This document provides a standard testing procedure for evaluating the water resistance of coatings using a water immersion test. The procedure involves partially immersing coated specimens in distilled water at 30 degrees Celsius for 24 hours. After removal from the water bath, the specimens are wiped dry and evaluated within 10 minutes for any changes in color, blistering or other effects from water exposure that could indicate degradation of the coating. The water immersion test is useful for research and quality control to determine if coatings will adequately resist damage from water over time.
This document provides a standard testing procedure for evaluating the water resistance of coatings using a water immersion test. The procedure involves partially immersing coated specimens in distilled water at 30 degrees Celsius for 24 hours. After removal from the water bath, the specimens are wiped dry and evaluated within 10 minutes for any changes in color, blistering or other effects from water exposure that could indicate degradation of the coating. The water immersion test is useful for research and quality control to determine if coatings will adequately resist damage from water over time.
Original Description:
water immersion test for coating application is a very good document prepared by rajan gangar
This document provides a standard testing procedure for evaluating the water resistance of coatings using a water immersion test. The procedure involves partially immersing coated specimens in distilled water at 30 degrees Celsius for 24 hours. After removal from the water bath, the specimens are wiped dry and evaluated within 10 minutes for any changes in color, blistering or other effects from water exposure that could indicate degradation of the coating. The water immersion test is useful for research and quality control to determine if coatings will adequately resist damage from water over time.
This document provides a standard testing procedure for evaluating the water resistance of coatings using a water immersion test. The procedure involves partially immersing coated specimens in distilled water at 30 degrees Celsius for 24 hours. After removal from the water bath, the specimens are wiped dry and evaluated within 10 minutes for any changes in color, blistering or other effects from water exposure that could indicate degradation of the coating. The water immersion test is useful for research and quality control to determine if coatings will adequately resist damage from water over time.
Testing water resistance of coatings using water immersion
Reference A part of this document has been referred from ASTM D 870 - 9702
Author: Rajan Gangar Reviewed By: Approved By:
Date : 30 th Aug14 Revision # 00
Scope: This test method covers the basic principles and operating procedures for testing water resistance of coatings by partial or complete immersion of coated specimens in distilled or de-mineralized water at ambient temperature conditions, this practice is limited to tests in water alone and is limited to the methods of obtaining, measuring and controlling the conditions and procedures of water immersion tests. It does not specify specimen preparation, specific test conditions or evaluation of results. Significance and use: Immersion in water can cause the degradation of coatings. Knowledge on how a coating resists water immersion is helpful in predicting its service life. Failure in water immersion test may be caused by a number of factors including a deficiency in the coating itself, contamination of substrate or inadequate surface preparation. The test is therefore useful in evaluating coatings alone or complete coating systems. Water immersion test is used for research and development of coatings and substrate treatments, specification acceptance and quality control in manufacturing. These tests typically result in pass or fail determination, but the degree of failure may also be measured. A coating system is considered to pass if there is no evidence of water related failure after a specified period of time. Procedure: 1. Fill the transparent plastic bag with distilled water to a depth such that the test specimen / coated glass bottle is partially immersed for approximately half the length of the test specimen.
2. A constant temperature of ~ 30 deg C is required to be maintained throughout the test.
3. Place the coated test specimens in the water bath for a period of 24 hrs unless or until specifically mentioned for specific evaluation purpose.
4. Conclude the test after the specified period of time or after effects from water immersion have been observed.
5. Wipe the test specimens dry. Rate specimens for changes in color, blistering etc.
6. Evaluate specimens no less than 5 min and no more than 10 min after removal from water bath, as the effects from water exposure can change within a short time. Remove only as many specimens as can be rated within the specified time.