Professional Documents
Culture Documents
Extensa 900 Series Notebook Computers: Maintenance Manual
Extensa 900 Series Notebook Computers: Maintenance Manual
Extensa
TM
900 Series
Notebook Computers
9813715-0001
December 1996
Copyright 1996 Texas Instruments
All Rights Reserved
Extensa
TM
900 Series Notebook Computers
Maintenance Manual
TI Part No. 9813715-0001
Original Issue: December 1996
Changes may be made periodically to the information in this publication. Such
changes will be incorporated in new editions of this manual.
No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical,
photocopy, recording, or otherwise, without the prior written permission of
Texas Instruments.
The equipment, as well as the programs that TI has created to use with them,
are tools that can help people better manage the information used in their
business; but tools including TI products cannot replace sound judge-
ment nor make the manager's business decisions.
Consequently, TI cannot warrant that its products are suitable for any specific
customer application. The manager must rely on judgement of what is best for
his or her business.
Address all correspondence regarding orders to:
Texas Instruments
P.O. Box 6102, M/S 3255
Temple, Texas 76503
Extensa is a trademark of Texas Instruments. The icons in the Windows Notebook and
Startup groups are copyrighted by Texas Instruments.
IBM and PS/2 are registered trademarks, and OS/2 is a trademark of International
Business Machines Corporation.
Microsoft, Windows and MS-DOS are registered trademarks of Microsoft Corporation..
Intel and Pentium are registered trademarks of Intel Corporation.
Cirrus is a registered trademark of Cirrus Logic, Inc.
Ethernet is a registered trademark of Xerox Corporation.
IRDA is a trademark of Infra Red Data Association.
Sound Blaster is a trademark of Creative Technology, Ltd.
SimulSCAN is a trademark of Cirrus Logic, Inc.
SCSI is a registered trademark of Security Control Systems, Inc.
Synaptics is a registered trademark of Synaptics, Inc.
Phillips is a tegistered trademark of Phillips screw Company.
TranXit is a trademark of Puma Technology, Inc.
Cyrix is a registered trademark of Dakota Systems, Incorporated.
CHIPS is a registered trademark of Chips Technologies, Inc.
AudioRack is a trademark of ESS Technology, Inc.
Preface ix
Preface
Introduction
This manual provides installation, operation and servicing data for the Extensa
TM
900
Series Notebook Computers.
Intended Audience
This manual is primarily intended for use by qualified service technicians but contains
information useful to non-technical users.
Contents
This manual contains six sections and one appendix that are common to all Extensa
900 Series Notebook Computers (differences described as they are covered):
Section 1: General Description - Introduces the main features of the Extensa
900 Series Notebook Computers; identifies all options, provides physical and
electrical specifications.
Section 2: Installation - Describes how to unpack, install options and begin
using the notebook.
Section 3: Operating Instructions - Describes the notebook computer
operating controls and indicators and basic operating procedures required to
support maintenance operations.
Section 4: Theory of Operation - Provides a block diagram level theory of
operation for the Extensa Series Notebooks.
Section 5: Troubleshooting Procedures - Provides troubleshooting
procedures for the notebook computer series.
Section 6: Field Service - Provides preventive and corrective maintenance
procedures for the notebook computer series including FRU removal/
replacement procedures.
Appendix A: Notebook Schematic Diagrams - Provides schematic diagrams
for the Extensa 900 Series Notebook Computer.
Appendix B: MPB Schematic Diagrams - Provides schematic diagrams for the
Extensa 900 Series Mobile Productivity Base.
x Preface
Other Manuals About the System
The following documents provide additional information related to the Extensa
Notebook Computer Series:
Extensa Series Notebook Computers Users Guide - Contains user reference
information for the Extensa 900 Series Notebook Computers.
PC-Doctor Help and Technical Reference (online)
Ordering Parts and Supplies
To order a copy of any TI publication or to order option kits, spare parts or supplies for
your system, contact your TI reseller:
Telephone Toll-free: 1-800-TI TEXAS.
Contents iii
Contents
Paragraph Page
Preface
Introduction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - vii
Intended Audience- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - vii
Contents - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - vii
Other Manuals About the System- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -viii
Ordering Parts and Supplies - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -viii
Section 1 General Description
Introduction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-1
Product Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-1
Video Display Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-3
Internal LCD - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-3
External CRTs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-3
Display Hot Key Sequences - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-3
Keyboard Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-4
Software Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-4
Standard Peripheral Devices - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-5
900 Series Connectivity Features- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-5
Notebook Expansion Capabilities- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-7
Memory Expanson - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-7
PCMCIA Card Options - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-7
Mobile Productivity Base Option - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-7
Docking and Undocking- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-10
Mobile Productivity Base Ports - - - - - - - - - - - - - - - - - - - - - - - - - 1-11
Advanced PCI Card Options - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-12
Notebook Battery - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-12
Standard Test Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-12
Power On Self Test - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-12
PC-Doctor Diagnostics Program- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-13
Extensa 900 Series Specifications - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-14
Regulatory Agency Approvals- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1-17
Section 2 Installation
Introduction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-1
Unpacking Instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-1
Installing Internal Notebook Options - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-2
Installing Main Memory Expansion (Optional) - - - - - - - - - - - - - - - - - - - - 2-2
Setting Up the Software - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-3
Installing PCMCIA Options - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-4
iv Contents
Contents (continued)
Paragraph Page
Section 2 Installation (continued)
Installing External Notebook Options - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-5
Installing the Mobile Productivity Base (Option) - - - - - - - - - - - - - - - - - - - 2-5
Docking the Notebook to the MPB - - - - - - - - - - - - - - - - - - - - - - - - 2-5
Cabling to the MPB - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-6
Installing Ext. Keyboard/Mouse/Numeric Keypad - - - - - - - - - - - - - - - - - 2-8
Installing an External Parallel Printer - - - - - - - - - - - - - - - - - - - - - - - - - - 2-9
Installing an External Serial Port Device - - - - - - - - - - - - - - - - - - - - - - - 2-10
Installing an External VGA Monitor - - - - - - - - - - - - - - - - - - - - - - - - - - 2-11
Primary Battery Pack Installation- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-13
Installing the AC Power Adapter - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-13
Initial Software Load - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2-14
Section 3 Operating Instructions
Introduction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-1
Controls/Indicators - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-1
Power On/Off Switch - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-2
Notebook LEDs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-2
LED Icons - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-2
Keyboard Hot Key Sequences - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-3
Windows 95 Special Keys - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-5
DOS Special Keys - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-5
Configuring the Touchpad- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-6
Using a CD-ROM Drive (MPB Option Only - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-6
Inserting a CD (MPB Option Only) - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-6
Handling CDs (MPB Option Only - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-6
Built-In Sound System- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-7
Turning Sound On/Off- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-7
Sound Software - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-7
External Sound Equipment- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-8
Using Remote Connections - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-8
Using the Fast Infrared (FIR) Port- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-8
Using Zoomed Video Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-9
MPEG PC Card - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-9
Battery Saving Tips - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-9
Lowering Inactivity Timeouts- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-9
Suspending Operation While Idle - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-10
Responding to a Low Battery Condition- - - - - - - - - - - - - - - - - - - - - - - - 3-10
Replacing the Battery- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-11
Saving to Disk - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3-11
Contents v
Contents (continued)
Paragraph Page
Section 4 Theory of Operation
Introduction- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-1
Notebook Functional Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-1
System Processor - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-3
Memory Subsystem- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-5
Main Memory- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-5
Flash ROM - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-6
System Controller Function - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-6
ALI M1521 (Memory, Cache and DRAM Controller)- - - - - - - - - - - - - 4-8
ALI M1523 (PCA-ISA Bridge)- - - - - - - - - - - - - - - - - - - - - - - - - - - - 4-9
Video Subsystem - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-12
C&T 65550 Features- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-12
Versatile Panel Support - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-13
Low Power Consumption - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-13
Software Compatibility/Flexibility - - - - - - - - - - - - - - - - - - - - - - - -4-13
Sound Subsystem- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-13
ESS1878 Audio Controller with Interface to Expansion Audio Mixer -4-13
ES1878 Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-14
Keyboard Subsystem- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-14
I/O Subsystem- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-14
NS87338VJG Super I/O Controller - - - - - - - - - - - - - - - - - - - - - - -4-14
Hard Disk Drive Subsystem - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-17
PCI0643 Features- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-17
Floppy Disk Drive Subsystem - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-18
PCI 1130 Features - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-19
PCMCIA Subsystem - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-18
Power Subsystem - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-20
ALI M6377 Power Management Unit - - - - - - - - - - - - - - - - - - - - - -4-22
AC Power Adapter- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-25
Mobile Productivity Base Interface - - - - - - - - - - - - - - - - - - - - - - - - - - - -4-25
Section 5 Troubleshooting Procedures
Introduction- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-1
Overview of Fault Isolation Process - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-1
Troubleshooting Procedures - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-3
Troubleshooting a Power Supply Problem - - - - - - - - - - - - - - - - - - - - - - - 5-3
Troubleshooting a Display Problem - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-3
Fault Isolation Using Power On Self Test- - - - - - - - - - - - - - - - - - - - - - - - 5-4
POST Error Messages - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-5
POST Beep Error Messages - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-8
Run-Time Error Messages - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-9
PCMCIA Modem Problems - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -5-10
vi Contents
Contents (continued)
Paragraph Page
Section 6 Troubleshootig Procedures (continued)
General Fault Isolation Procedures - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-12
Fault Isolation Using Diagnostics - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-13
PC-Doctor (In DOS Mode or DOS Windows) - - - - - - - - - - - - - - - - - - - - - 5-13
Supporting Online Documentation- - - - - - - - - - - - - - - - - - - - - - - - - - - 5-15
User Interface to PC-Doctor - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-15
Quitting PC-Doctor - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5-15
Section 6 Field Service
Introduction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-1
Preventive Maintenance - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-1
Cleaning the Computer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-1
Handling the Computer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-2
Handling the Computer Battery Pack - - - - - - - - - - - - - - - - - - - - - - - - - - 6-2
Password Caution - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-3
Required Tools and Equipment - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-3
Notebook FRUs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-3
Cover-Display Assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-4
System Base Assembly- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-6
Mobile Productivity Base Assembly - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-9
Notebook FRU Replacement Procedures - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-10
Removing/Replacing the Notebook Battery Pack- - - - - - - - - - - - - - - - - - 6-11
Removing/Replacing PCMCIA Options - - - - - - - - - - - - - - - - - - - - - - - - 6-12
Installing/Removing the Mobile Productivity Base- - - - - - - - - - - - - - - - - 6-13
Removing/Replacing the Hard Disk Drive Assembly - - - - - - - - - - - - - - - 6-15
Removing/Replacing the Keyboard Assembly - - - - - - - - - - - - - - - - - - - - 6-16
Heat Sink Assembly Removal/Replacement - - - - - - - - - - - - - - - - - - - - - 6-17
Display Assembly Removal/Replacement - - - - - - - - - - - - - - - - - - - - - - 6-18
Removing/Replacing the LED/Microphone Board Assembly - - - - - - - - - - 6-19
Removing/Replacing the CPU Board- - - - - - - - - - - - - - - - - - - - - - - - - - 6-20
Removing/Replacing the Top Cover - - - - - - - - - - - - - - - - - - - - - - - - - - 6-21
Removing/Replacing the VGA Video Board - - - - - - - - - - - - - - - - - - - - - 6-23
Removing/Replacing the Power Supply Board - - - - - - - - - - - - - - - - - - - 6-24
Removing/Replacing the DC-In Board Assembly- - - - - - - - - - - - - - - - - - 6-25
Removng/Replacing the PC Card Module - - - - - - - - - - - - - - - - - - - - - - 6-26
Removing/Replacing the Main Board Assembly - - - - - - - - - - - - - - - - - - 6-27
Removing Touchpad and Speakers- - - - - - - - - - - - - - - - - - - - - - - - - - - 6-28
Removing/Replacing the Display Bezel - - - - - - - - - - - - - - - - - - - - - - - - 6-29
Removing/Replacing the LCD - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-30
Removing/Replacing the Display Inverter Boards - - - - - - - - - - - - - - - - - 6-31
Removing/Repalcing MPB FRUs- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6-32
Removing/Replacing the Media Bay Device - - - - - - - - - - - - - - - - - - - - - 6-32
Contents vii
Contents (continued)
Paragraph Page
Section 6 Field Service (continued)
Removing/Replacing the MPB Battery - - - - - - - - - - - - - - - - - - - - - - - - -6-33
Removing/Replacing the MPB Housing- - - - - - - - - - - - - - - - - - - - - - - - -6-34
Removing/Replacing the Docking Cable - - - - - - - - - - - - - - - - - - - - - - - -6-35
Removing/Replacing the Docking Mechanism - - - - - - - - - - - - - - - - - - - -6-36
Removing/Replacing the MPB DC-DC Converter - - - - - - - - - - - - - - - - - -6-37
Removing/Replacing the MPB Main Board Assembly - - - - - - - - - - - - - - -6-38
Appendix A Notebook Schematic Diagrams
Introduction- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A-1
Appendix B Notebook Schematic Diagrams
Introduction- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - B-1
Appendix A POST BIOS
Introduction- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - C-1
General Description 1-1
1
General Description
1.1 Introduction
This manual contains field and factory level servicing information for the Extensa
TM
900
Series Notebook Computers (Figure 1-1) marketed by Texas Instruments. This section
provides a general overview of the Extensa 900 Series, describes the standard and
optional features, and identifies the major assemblies and subassemblies. This section
also contains detailed functional and environmental specifications for the Extensa 900
Series Notebook Computers.
Figure 1-1 Extensa 900 Series Notebook Computers
1.2 Product Overview
The Extensa 900 Series Notebook Computers are ultra-slim, large screen, high-
performance, multimedia notebooks powered by the Intel
P54CSLM Pentium
Processor Chip (133-MHz). The Extensa 900 can be equipped with an optional Mobile
Productivity Base that allows for quick connect/disconnect to/from the desktop
environment and expanded functionality (modular bay and Advanced PCI card
features).
Other major features of the 900 Series include:
133 MHz Pentium processor with internal 256 KB cache memory and math
coprocessor
Basic Extensa 900 Series
Notebook
Extensa 900 Series
with Mobile Productivity Base
1-2 General Description
Powerful PCI Bus architecture
16 MB main memory (expandable to 80 MB using 8 MB, 8 MB, 16 MB, 32 MB
or 64 MB EDO 64-bit type small outline dual inline memory module (soDIMM)
upgrades)
256 KB Level-2 cache memory
Built-in 2.5-inch IDE high capacity (1.35 GB or greater) Hard Disk Drive
External Floppy Drive Module (attaches to the Parallel Port)
Advanced video features
- DSTN or TFT internal color display
- Simultaneous display with external CRT
- 2.0 MB video memory
- Fast video graphics accelerator
Built-In 86/87-key keyboard
Internal touchpad pointing device with two Select buttons
Fast Infrared communications
Built-in audio features
- 16-bit stereo audio
- Line In, Line Out and Microphone In stereo jacks
Small, lightweight AC adapter, auto-switching (90 VAC to 264 VAC, 50-60 Hz)
Portable power system with advanced power savings features for extra long
battery life
- Zero-Volt Suspend, 5-Volt Suspend and Standby power saving modes
- Rechargeable Li-Ion battery pack
Powerful expansion capabilities including:
- Flexible set of desktop ports including external CRT (and simultaneous
LCD and external CRT display), 9-pin serial port, parallel port for
external printer/floppy drive, PS/2
CL-GD7548, ESS 1888 Sound Device Drivers, WinModem Device Drivers, PC-Card Bus Socket
Services and Card Services Device Drivers, and Windows 95 MPEG-1 Software Audio/Video
Compression Device Drivers.
Windows/DOS 6.22 This environment has some limitations in the Plug N Play area; includes TI utilities and various
device drivers including Cirrus CL-GD7548, ESS 1888 Sound Device Drivers, WinModem Device
Drivers, PC-Card Bus Socket Services and Card Services Device Drivers, etc.
1-6 General Description
1.2.4 Standard Peripheral Devices
As standard features, the Extensa notebooks include an internal IDE hard drive, an
external 3.5-inch floppy disk drive and built-in touchpad (mouse device).
1.2.5 900 Series Connectivity Features
As standard features, the Extensa 900 Series notebooks includes most standard
desktop ports including a serial port, parallel port, PS/2 port, and external VGA port.
The 900 Series also includes a fast infrared (FIR) port and an expansion bus connector
for attaching to the optional Mobile Productivity Base. The external ports for the 900
Series are shown in Figure 1-4 and described in Table 1-2.
Figure 1-4 900 Series External Ports
VGA
Port
Serial
Port
Parallel
Port
AC Adapter
Connection
PS/2
Port
FIR
Port
Line
Out
Line
In
Mic
In
General Description 1-7
Table 1-2 900 Series External Ports
1.2.6 Notebook Expansion Capabilities
In addition to the external ports, the Extensa 900 Series Notebooks are designed with
a variety of expansion features that permit substantial functionality and performance
upgrades over the life of the product. The expansion capabilities built into the notebook
are summarized in Table 1-3 and described in greater detail in the following paragraphs.
Port Assignment Description
External VGA Port 15-pin Female connector used to attach an external SVGA monitor to the
notebook.
Serial Port 9-pin Male connector used to attach an RS-232 serial device to the notebook.
Parallel Port 25-pin Female connector used to attach a bidirectional printer or an external
floppy disk drive (requires special cable for use with floppy disk drive).
PS/2
Port
6-pin Circular connectors used to attach external keyboard/mouse devices to
the notebook.
AC Adapter Connector Power in connector used to attach the output of the AC adapter to the
notebook.
Fast Infrared Port Fast Infrared Port (4 M/b) used for wireless communications between the
notebook and an FIR-equipped device such as keyboard, another notebook,
printer, etc.
Audio In/Out, Mic In Jacks Stereo audio line inputs, stereo line outputs and external microphone input
MPB Bus PCI Bus plus sidebands that support an optional Mobile Productivity Base.
Table 1-3 Extensa 900 Expansion Features Summary
Expansion Feature Description
External 3.5-inch Diskette Drive Module Provides convenient storage on a removable diskette format
Memory Expansion Features Main memory can be expanded from 16 MB to a maximum of 80 MB using
one soDIMM module (8 MB, 16 MB, 32 MB, or 64 MB configurations).
Flash ROM (hardware feature) Permits new versions of BIOS to be downloaded into Flash ROM without
physically having to replace the ROMs
PCMCIA Slots Allows installation of any optional PCMCIA device such as speakerphone
modems, Ethernet
devices, CD-ROM
drives). The test results are stored in a log which can be printed out (by pressing F2)
or saved in a disk file (by pressing F3).
Features of the diagnostic program are accessed through a series of pull-down menus
and basic keyboard keys (cursor keys to move highlighted pointer, Enter key to select
a highlighted feature, Esc key to cancel a function and move back one level.
PC-Doctor is typically user-friendly but if you don't understand a feature, context-
sensitive help information is available at any time by pressing the F1 function key;
pressing the F1 function key twice accesses the online Technical Reference Manual for
PC-Doctor.
A powerful set of utilities within PC-Doctor (that can be run locally or remotely) simplify
the task of determining system configuration data, allocating and using system memory,
IRQ and DMA use, what device drivers are installed, what COM and LPT ports are
assigned and what ports are available, identifying partitioning data for fixed disk
drive(s), determining the VGA setup information, reading the software interrupts/
interrupt vectors, etc.
Note: Refer to Troubleshooting Procedures (Section 5) for additional information
regarding the Diagnostics Program.
1-14 General Description
1.5 Extensa 900 Series Specifications
General specifications for the Extensa 900 Series Notebooks are provided in Table 1-5.
Table 1-5 Extensa 900 Specifications
Characteristic Model 900 Series Specifications
CPU
Pentium P54CSLM, 133 MHz; 3.1 Volt,
Internal Hard Disk Drive
Disk Storage Capacity:
Average access time:
Throughput
1.35 GB or greater
12 ms or less
11+ Million I/O's per second
DRAM Memory
Size
Maximum Expansion Size
16 MB DRAM, 60-ns, page-interleaved
80 MB
Flash ROM:
256 KB
FDD
Disk Storage Capacity:
Disk Size
Drive Height
Mode
External
1.44 MB
3.5-inch disk
12.5 mm
Choice of 720 KB/1.2 MB or 1.44 MB
CD-ROM Drive
Available with Mobile Productivity Base option
LCD Display
12.1-inch DSTN, SVGA or 11.3-inch TFT, SVGA
Software
Dual Load
Internal Keyboard
Key Travel
86/87-key, PS/2 and AT-compatible
Embedded Numeric Keypad
3 mm
Built-in Mouse Device
Touchpad built-in to the base of the keyboard (select buttons on sides
of Touchpad)
General Description 1-15
Video Subsystem
LCD Aspect Ratio
Emulations:
Video Memory Size
Video Bus:
LCD Resolution:
LCD Characters/Line
LCD Lines/Screen:
LCD Brightness Control:
1-1
SVGA
1.5 MB
32-bits
640 x 480 pixels bit-mapped at 256 colors
80
25
Function hot key brightness and contrast control and SimulSCAN
control
External CRT Monitor
Interface
Connector Type:
Monitors Supported:
15-Pin, female, D-type connector
640 x 480 with 16.7 million colors on CRT
800 x 600 with 65K colors on CRT
1024 x 768 with up to 256 colors on CRT
Table 1-5 Extensa 900 Specifications
Characteristic Model 900 Series Specifications
1-16 General Description
RS-232-D Serial Port:
Method:
Type:
Bits per second:
Parity: Transmit:
Receive:
Line control:
Data word:
16550 UART Support
Selectable Serial Port
(BIOS Setup)
9-Pin, male, sub-D-type connector
EIA RS-232-D
Asynchronous transmission
110, 200, 300, 600, 1200, 2400, 4800, 9600, 19200
Odd, even, mark, space
Data check: odd, even
READY/BUSY, DC1/DC3
7- or 8-bit
Yes
COM1(IRQ4, 3F8h)
COM2(IRQ3, 2F8h)
COM3(IRQ4, 3E8h)
COM4(IRQ4, 2E8h)
Disable
Parallel Port
Connector Type
EPP/ECP Bidirectional
25-Pin, DB-25 Connector
Fast I/R Port
Transfer Data Rate
Yes
4 Mb/s
Mobile Productivity
Base Ready
Yes
Table 1-5 Extensa 900 Specifications
Characteristic Model 900 Series Specifications
General Description 1-17
1.6 Regulatory Agency Approvals
All Extensa 900 Series products meet the following regulatory agency standards:
Underwriters Lab (UL) Standard 1950 (safety)
Canadian Standards Association (CSA) Standard 950 or CUL (safety)
FCC CFR 47, Part 15, Subpart B, FCC Level B (Emissions)
Canadian Department of Communications (DOC) ICES, Class B (Emissions)
VDE- EN60950 (Safety)
EN 50082-1 (Immunity: ESD, RFI, EFT, and Surge)
EN 50081-1 (Emissions: RFI, EMI, Harmonics, and Flicker)
Approval Marks: UL, CUL, VDE, FCC, and CE
Installation 2-1
2
Installation
2.1 Introduction
This section contains unpacking and preparation for use instructions for the Extensa
900 Series Notebook Computers. This includes:
Removing the computer and all manuals, options and accessories from the
shipping container(s)
Installing Internal Notebook Options
Installing External Notebook Options
Installing Battery Packs
Installing Desktop Devices
Installing the AC Adapter
Checking Out the System
Installing the System Software
Making Backups of System Software
Loading Application Software
2.2 Unpacking Instructions
Unpack the computer using the following instructions:
1. Carefully cut the tape that seals the top flap of the shipping carton.
2. Remove the computer and the accessories carton from the main shipping
carton.
3. Remove all protective coverings from the computer.
4. Open the accessory box; remove the contents.
Note: Save the two shipping containers and packaging for later reuse.
2-2 Installation
2.3 Installing Internal Notebook Options
If you have no internal options to install at this time, skip to Paragraph 2.4. Otherwise,
continue with Paragraph 2.3.1.
2.3.1 Installing Main Memory Expansion (Optional)
Main memory on the 900 Series Notebooks can be expanded using an EDO Small
Outline Dual Inline Memory Module (EDO soDIMM). These modules are available in
8 MB, 16 MB, 32 MB, and 64 MB sizes and install in the expansion memory slot on
the System Board accessed through the Memory Expansion Door on the bottom of the
notebook. The installation process consists of the following steps:
Caution: The EDO soDIMM module option contains components that are
sensitive to static electricity. When handling the module and the internal
parts of the computer, protect against static electricity by using wrist or
ankle grounding straps and grounded working mats. When moving or
storing items, use the anti-static bags supplied with the items.
1. Ensure that the notebook is powered off and the AC adapter disconnected
from the AC outlet. Also, ensure that all batteries are out of the unit.
2. Disconnect any peripheral device interface cables from the external interface
connectors and remove any installed PCMCIA options.
3. Turn the notebook over and locate the Expansion Memory Access Cover on
the bottom of the notebook.
4. Remove the screw holding the Expansion Memory Access Cover and remove
the cover.
5. Remove the EDO soDIMM module from its shipping container.
6. Refer to Figure 2-1. To install an soDIMM module, first align the connector
edge of the memory module with the key in the connector. Insert the edge of
the memory module board into the connector using a rocking motion to fully
insert the module. Push downward on each side of the memory module until
it snaps in place.
7. Reinstall the Expansion Memory Access Cover using the screw removed in
Step 4.
8. Replace the batteries and AC adapter.
9. Power up the notebook. If all of the installed memory is not recognized, try
reseating the soDIMM module and rebooting.
Installation 2-3
Figure 2-1 Memory Expansion Removal/Replacement
Note: After installing expansion memory in your notebook, you must run the
PHDISK utility in order for the Save-To-Disk or 0V Suspend functions to operate
correctly.
2.3.2 Setting up the Software
Note: If you are using an operating system other than Windows 95, Windows for
Workgroups, or DOS, you may need to re-partition your hard disk drive to allow
for the additional memory. Check with your system administrator.
Expansion
Memory
Access
Cover
Inserting
soDIMM
Memory
Module
2-4 Installation
In Windows 95
Follow these steps if your computer is running Windows 95.
1. From the Taskbar, select Start then Shut Down.
2. Select the Restart the Computer in MS-DOS mode.
3. Click on Yes.
4. Type PHDISK /C /F at the DOS prompt and press Enter.
5. The DOS screen appears and shows the save file name and size. Press any
key to reset the system. The computer will reboot.
In Windows for Workgroups
Follow these steps if your computer is running MS-DOS
and Windows for Workgroups.
1. Close all applications and exit Windows for Workgroups to MS-DOS.
2. At the command prompt (typically C:\) type PHDISK /C /F and press Enter.
This will create a file which can be used to save the contents of your memory
system when you perform a 0V Suspend operation.
2.3.3 Installing PCMCIA Options
The Notebook has two connector slots for PCMCIA option cards. These two slots can be
used to install one Type III or two Type I/II credit card size PCMCIA option cards. You
can install a PCMCIA (PC card) without turning the computer off.
Use the following procedure to install a PCMCIA option:
1. Review the installation instructions supplied with the PCMCIA option card(s).
2. Hold the card at the end opposite the connector pins with the label side up.
Insert the card into an unused slot on the left side of the Notebook.
3. If the option requires external cabling (e.g., modem option), connect external
cabling at this time.
Note: After installation of a PCMCIA option card, Windows 95 displays the New
Hardware Found dialog box to help you configure the new device. To remove a
card, click on the PCMCIA icon; then, press the appropriate PC Card Release
lever (or press both levers for a Type III device) and remove the option.
Installation 2-5
Figure 2-2 Installing PCMCIA Option Cards
Note: When installing a Zoomed Video option card, the card must be installed in
the lower card slot (slot 0 or A). Other option cards can be installed in either card
slot.
2.4 Installing External Notebook Options
2.4.1 Installing the Mobile Productivity Base (Option)
If using the Mobile Productivity Base option, install this accessory now. If not using
the MPB at this time, proceed directly to Paragraph 2.4.2.
2.4.1.1 Docking the Notebook to the MPB
To dock the Notebook Computer into the MPB, use the following procedure:
1. Turn the notebook over and open the expansion door (slide the door toward
the center of the notebook) to expose the docking connector.
2. Slide the lever release latch to the front of the MPB to release the docking
lever (refer to Figure 2-3).
2-6 Installation
3. Swing the Docking Lever outward a full 90 degrees from the side of the MPB.
4. Slide the notebook into the MPB, right side first, as shown in Figure 2-3.
Ensure that the docking guides on both the notebook and the MPB are
securely hooked.
5. Rest the notebook on the MPB. Then press and hold the notebook against
the MPB and swing the Docking Latch inward until the Lever Release Latch
locks.
Figure 2-3 Docking the Notebook into the MPB
2.4.1.2 Cabling to the MPB
Refer to Figure 2-4 (MPB Port Assignments) and then connect all desktop devices to the
MPB instead of directly to the notebook as described in Paragraphs 2.4.2 through 2.4.5.
1 2
3
4
Open the expansion door
on bottom of notebook
Slide release latch on MPB
forward; swing the docking
level outward 90 degrees
Slide notebook into MPB,
right side first; ensure
docking guides are hooked
Press and hold down
notebook and swing the dock
lever in until the release latch
locks
Installation 2-7
Figure 2-4 MPB Port Assignments
PS/2
Keyboard
Port
PS/2
Mouse
Port
Parallel
Port
Serial
Port
VGA
Port
Advanced
PCI
Line
Out
Line
In
Mic
In
2-8 Installation
Figure 2-5 MPB Battery Pack Removal/Installation Installation
2.4.2 Installing Ext. Keyboard/Mouse/Numeric Keypad
A PS/2 compatible Keyboard, mouse or an optional PS/2-compatible numeric keypad
may be installed on the notebook via the mouse connector on the left rear port as shown
in Figure 2-6.
Note: Refer to Figure 2-4 for port assignments if using the MPB option.
Battery Pack
Installation 2-9
Figure 2-6 PS/2 Port Connections
2.4.3 Installing an External Parallel Printer
The Notebook is equipped with an external, bidirectional, ECC/EPP compatible, 25-pin
parallel printer port. The connector pinouts and connector location are shown in
Figure 2-7.
Note: Refer to Figure 2-4 for port assignments if using the MPB option.
2-10 Installation
Figure 2-7 Parallel Port Pinouts
2.4.4 Installing an External Serial Port Device
The notebook contains an external RS-232 serial port with a 9-pin, male DB-9 connector
as shown in Figure 2-10 (25-pin cables require the use of an adapter for use with the
9-pin port). The serial ports are used to interconnect such devices as:
External Modem
Serial Mouse
Serial Printer
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
SIGNAL
SPP Mode
STB*
PD0
PD1
PD2
PD3
PD4
PD5
PD6
PD7
ACK*
BUSY
PE
SLCT
AFD*
ERR*
Ground
INIT*
SLIN*
Note: * Denotes
Active Low
Strobe*
Data Bit 0
Data Bit 1
Data Bit 2
Data Bit 3
Data Bit 4
Data Bit 5
Data Bit 6
Data Bit 7
Acknowledge*
Paper Out
Busy
Auto Line Feed*
Select
Error*
Initialize Printer*
Select In*
LPT18
LPT18
VCC VCC
PLP120
PLP121
PLP122
26 Ground
PLP121
PLP122
PLP120
FDD 5V FDD 5V
FDD 5V FDD 5V
LP125 LP125
PARALLEL PORT PINOUTS
Installation 2-11
Any device that uses an RS-232 interface
Note: Refer to Figure 2-4 for port assignments if using the MPB option.
Caution: Never connect a parallel device to a serial port or a serial device
to a parallel port or video port; this may cause damage to the notebook
and/or external device. If you are uncertain of what type connector the
external device has, refer to the technical manual for the external device.
Figure 2-8 Serial Port Pinouts
2.4.5 Installing an External VGA Monitor
The notebook (and optional MPB) contain an external CRT port that can drive one of
a variety of monitor resolutions and colors as summarized in Section 1. The associated
connector location and pinouts for the notebook are shown in Figure 2-9.
Note: Refer to Figure 2-4 for port assignments if using the MPB option.
2-12 Installation
Figure 2-9 External VGA Pinouts
Use the following procedure to install an external monitor:
1. Turn off power to both the notebook and monitor.
2. Connect the 15-pin external VGA cable from the monitor to the VGA connector
on the notebook computer (Figure 2-9) or MPB (Figure 2-4).
3. Power up the notebook computer first; then, turn on power to the monitor.
4. Setup the notebook display mode for LCD only, simultaneous LCD and CRT
or CRT only (under Windows 95, select the Change Display Utility; under
Installation 2-13
Windows for Workgroups, use the WinMode Utility).
5. Install the correct driver, if required (refer to the Monitor Installation
Instructions supplied by the CRT vendor).
2.5 Primary Battery Pack Installation
1. Turn off the computer and disconnect the AC adapter if attached to the
computer.
2. Unlatch the end locks by pushing the endcaps outward with your thumbs.
3. Align battery connector to connector on notebook and insert the battery pack
into the battery compartment; then push the battery in completely until you
feel the contacts engage.
4. Relatch the battery locks on both ends of the battery.
Figure 2-10 Notebook Battery Removal/Replacement
2.6 Installing the AC Power Adapter
Use the following procedures to connect the AC adapter to the system:
Caution: Use only the AC adapter supplied with the computer; other
adapters can damage the unit.
Unlock Battery Pack
Remove Battery
from Front of Notebook
If Battery Lock comes off,
reinstall as shown
Flush
Slide
2-14 Installation
1. Remove the AC adapter from the packaging. Connect the round coaxial
connector supplied with the notebook to the DC IN power receptacle on the
left rear of the notebook as shown in Figure 2-9.
2. Connect the female side of the AC power cord to the AC adapter and connect
the male end to a grounded AC outlet.
Figure 2-11 Installing the AC Adapter
2.7 Initial Software Load
After unpacking and setting up the notebook for the first time, you must perform an
initial software load that takes approximately 30 minutes.
Because of the way Windows 95 structures its files, stopping in the middle of the setup
process can cause irreversible file damage.
AC Adapter
DC-IN Connector
2-15 Installation
Before starting the initial software load process, ensure that you have the following:
Extensa 900 Users Guide - Contains latest software installation instructions.
AC Adapter/Access to AC power - Although the battery pack may have some
charge, it may be insufficient for the entire set up. Loss of power during setup
can cause irreversible file damage.
Certificate of Authenticity - You will need to enter the number from your
Windows 95 Certificate of Authenticity during Windows 95 Setup. This
certificate is part of the Windows 95 documentation kit. You need this number
even if you are installing Windows for Workgroups.
Language - During initial setup you choose the following:
- Language for Windows displays
- Language for keyboard installed
Printer type - As part of the Windows setup, you are prompted to choose a
printer. Microsoft
Touchpad utility. Configure the touchpad using the Mouse utility located
in the Control Panel Window. Follow these steps to configure the Touchpad:
In Windows 95
1. Select the Start button, then select Settings.
2. Select Control Panel to display the Control Panel window.
3. Double-click on the Synaptics Touchpad icon.
4. Select the touchpad tab to customize the touchpad to your preference.
5. Click on Enhancements to bring up additional features and to get to the
online help for the Synaptics Touchpad drivers.
In Windows for Workgroups
1. From the Program Manager double-click on the Main program group.
2. Double-click on the Control Panel icon.
3. Double-click on the Synaptics Touchpad icon.
4. Select the touchpad tab to customize the touchpad to your preference.
5. Click on Help for the Synaptics Touchpad drivers online documentation.
3.4 Using a CD-ROM Drive (MPB Option Only)
An optional CD-ROM drive installed in the modular bay of a docked Mobile Productivity
Base option provides fast access to text, programs, graphics, sound, animation and
video on a standard CD. (With an optional MPEG PC Card installed, you can play back
approximately 75 minutes of MPEG1-compressed, full-motion video from a CD.)
3.4.1 Inserting a CD (MPB Option Only)
1. With the system powered up, press the eject button on the front of the
CD-ROM drive to eject the disc tray.
2. Slide out the disc tray.
3. Place the CD, label side up, in the depression on the disc tray.
4. Slide the disc tray into the drive.
3.4.2 Handling CDs (MPB Option Only)
Follow these guidelines to avoid damaging your CDs:
When removing a CD from its protective case or loading a CD into a drive, hold
the CD by its central hole and outer edge. Never touch the data surface (non-
label side).
Operating Instructions 3-7
To protect the CD against scratches and dirt when not in use, keep the CD in
its protective case.
Clean a CD with a clean, dry, lint-free cloth. Always wipe from the center to
the edge. Dont wipe the CD in a clockwise or counterclockwise direction.
Keep CDs away from high temperatures and direct sunlight.
3.5 Built-In Sound System
The Extensa 900 Series Notebook comes with an internal microphone and stereo
speakers. These features give direct sound generation and recording capability in the
system.
3.5.1 Turning Sound On/Off
To mute or restore sound, press the following keys:
Fn+PgUp: Turns mute On/Off
3.5.2 Sound Software
The computer has pre-installed sound support utilities in the AudioRack32 group.
These include:
AudioRack32
Audio Recorder
3-8 Operating Instructions
3.5.3 External Sound Equipment
You can improve the quality of sound production and increase convenience by
connecting external sound equipment.
The computer has the following jacks for connecting to external sound equipment:
Microphone Input
Stereo Headphone/Speaker Line Output
Stereo Line Input
3.6 Using Remote Connections
The computer can send and receive e-mail, surf the Internet, connect to one of the
online services or share files with other office employees.
The Extensa communicates with the outside world in one of the following ways:
Over a telephone line using a PC Card modem installed in the computer
Over a network using a network adapter
Note: You can purchase compatible modems and network adapters from your
dealer or directly from Texas Instruments.
3.6.1 Using the Fast Infrared (FIR) Port
The FIR port, located on the rear of the computer, offers wireless communication with
other Texas Instruments notebook computers or a variety of IRDA-compliant devices.
Without a physical connection, you can print remotely, transfer files between
computers, use a remote mouse during a presentation or receive information from a
PDA or pocket organizer. To transfer a file follow these steps:
Align the FIR ports of the two devices making sure that the distance separating them
is between six inches and three feet (one meter).
After the devices are aligned, use the TranXit software, located in the TranXit group,
to complete the communication process. (For further information, refer to the online
TranXit Quick Reference Guide.)
Operating Instructions 3-9
3.7 Using Zoomed Video Features
Your computer supports Zoomed Video (ZV) PC Cards through the PC Card slots. ZV
PC Cards connect to the internal ZV port, allowing advanced multimedia capabilities
such as video conferencing and on-screen television at full, smooth motion. The Zoomed
Video port adds a dedicated video bus that provides a direct link between a PC Card
and the VGA accelerator or audio DAC. This detour lets video and audio data bypass
the PCI bus, reducing bandwidth impositions and improving system performance for
more fluid audio and video.
3.7.1 MPEG PC Card
The optional MPEG PC Card uses the Zoomed Video port built into the computer to
display MPEG video and audio on the computer. The MPEG card features MPEG-1
video playback with 16.7 million colors, MPEG-1 audio layers I and II, is MPC3
compliant and Windows 95 Plug and Play. With this option you can run full-motion
video, combined with digital audio, graphics, text and data, enabling you to create far
more effective presentations or play the most advanced video games.
3.8 Battery Saving Tips
There are a number of actions you can take to reduce the rate at which your computer
depletes the battery. By taking some or all of these actions, you can substantially
increase the time you can operate on battery power before recharging the battery:
Reducing screen brightness Although the screen controller uses new
technology to increase brightness without increasing energy consumption, the
screen is still the largest single consumer of the battery charge. Reducing the
brightness to the lowest acceptable level increases battery life. To reduce the
brightness, press Fn+.
Caching the hard disk drive - By caching the hard disk drive, you can reduce
the length of time the hard disk drive is rotating and using energy. Both
Windows 95 and Windows for Workgroups use a disk-caching program by
default. As long as you have not disabled these programs, you can take
advantage of the battery savings.
3.8.1 Lowering Inactivity Timeouts
Inactivity timeouts turn off devices in the computer when you are not using them.
Lowering the inactivity timeouts shortens the period of time the computer waits before
turning off the device.
3-10 Operating Instructions
3.8.2 Suspending Operation While Idle
Although the computer goes into Suspend mode automatically after a defined period of
inactivity, you can reduce energy consumption even further by pressing either Fn+F3
(Suspend) or Fn+F4 (Standby) as soon as you no longer need the computer to be active.
Pressing Fn+F4 (Standby) turns off the screen.
Pressing Fn+F3 (Suspend) turns off the screen, stops the hard disk drive, and
reduces energy usage to the lowest level possible without turning off the
computer.
Pressing the Shift key resumes activity after the notebook has been in either
the Suspend or Standby modes.
3.8.3 Responding to a Low Battery Condition
When you are operating the computer on battery power and the charge remaining is
down to between 10% and 20%, the battery-low indicator blinks and an audible alarm
sounds. When this happens you should take the following actions to conserve battery
power and reduce the possibility of data loss.
Saving files Save all open files frequently while the computer is in a
low-battery condition.
Turning off the alarm Turn off the audible alarm by pressing Fn+End
(Mute).
Reducing screen brightness Reduce screen brightness by pressing Fn+.
Connecting the AC adapter If you have access to AC power, connect the
computer to the AC adapter. You can do this without turning off the computer.
Suspending operations Press Fn+F3 or Fn+F4 to put the computer into
Suspend or Standby mode whenever you are not actively using the computer.
Press the Shift key to bring the computer out of Suspend or Standby mode.
Operating Instructions 3-11
3.8.4 Replacing the battery
If you have a spare, charged battery, you can do one of the following.
Insert a secondary battery into the MPB option (if installed).
If you already have a battery in a docked MPB, you can replace the primary
battery without turning off the computer.
If you cannot insert the spare battery, suspend operations to disk by pressing
Fn+F2 and replace the battery. When you turn on the computer, the computer
returns to the saved state.
3.8.5 Saving to Disk
When the battery power becomes critically low (less than 5% charge remaining), the
computer saves the current state of the computer to disk and turns off. When you turn
the computer on again, the computer restores the state that was saved to disk.
Theory of Operation 4-1
4
Theory of Operation
4.1 Introduction
This section contains a general block diagram theory of operation description of the
Extensa 900 Series Notebook Computers.
Note: Various internal components may change on future models and
busses/bus speeds are subject to change.
4.2 Notebook Functional Overview
The Extensa 900 Series Notebooks consist of eight major functions or sections
including:
System Processor implemented on the Main Board Assembly
Memory Subsystem implemented on the Main Board Assembly
I/O Subsystem implemented on the Main Board Board
Keyboard Subsystem implemented on the Main Board Assembly and the
Keyboard Assembly
Video Subsystem implemented on the Main Board and LCD Display Panel
assemblies
Sound Subsystem implemented on the Main Board Assembly
Touchpad Mouse Subsystem implemented on the Touchpad assembly and
on the Main Board Assembly
Hard Disk Drive Subsystem implemented on the Main Board Assembly and
the Hard Disk Drive Assembly
Floppy Disk Drive Subsystem implemented on the Main Board Board and
Floppy Disk Drive Assembly
PCMCIA Controller and Sockets implemented on the PCMCIA Module and
on the Main Board
Power Subsystem implemented on the Main Board, the battery pack, and
the AC adapter
4-2 Theory of Operation
Figure 4-1 Extensa Functional Block Diagram
586
CPU
SRAM M1521
BGA
DRAM
HDD
M1523
Graphic
controller
IDE Master
CD
CPU Bus
PCI Bus
ISA Bus
MPB
Theory of Operation 4-3
4.2.1 System Processor
The System Processor function for the notebook is implemented on the Main Board in
the form of an Intel Pentium P54-C Superscalar 586 Processor Chip. The processor
operates in conjunction with RAM and ROM Memory and other control logic to process
software instructions (BIOS, DOS, Windows, and applications). The processor
communicates with the hard disk drive and the memory components using high speed
busses.
The Processor also interacts with other hardware logic to provide the power savings
features for the notebook. These features include controlling CPU clock speeds,
reducing clock speeds whenever possible, e.g., when performing floppy disk drive
accesses, powering down unused devices, etc. A detailed block diagram of the Extensa
900 Series Notebook is shown in Figure 4-2.
The IRQ assignments for the 900 Series Notebooks is provided in Table 4-1.
Table 4-1 Interrupt Channel map
Priority Interrupt Number Interrupt Source
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
SMI
NMI
IRQ 0
IRQ 1
IRQ 2
IRQ 8
IRQ 9
IRQ 10
IRQ 11
IRQ 12
IRQ 13
IRQ 14
IRQ 15
IRQ 3
IRQ 4
IRQ 5
IRQ 6
IRQ 7
Power management unit
Parity error detected, I/O channel error
Interval timer, counter 0 output
Keyboard
Interrupt from controller 2 (cascade)
Real-time clock
Cascaded to INT 0AH (IRQ 2)
Audio (option) / PCMCIA
Audio (option) / PCMCIA
PS/2 mouse
INT from coprocessor
Hard disk controller
CD-ROM controller
Serial port 2, 4
Serial port 1, 3
Parallel port 1 / audio (option)
Diskette controller
Parallel port 2 / audio (option)
NOTE: A PCMCIA card can use IRQ 3, 4, 5, 7, 9 and 11 as long as
it does not conflict with the interrupt address of any other device.
4-4 Theory of Operation
Figure 4-2 Detailed System Block Diagram
C
P
U
M
1
5
2
1
M
1
5
2
3
P
C
I
B
U
S
I
S
A
B
U
S
P
C
I
1
1
3
0
6
5
5
5
0
/
S
3
P
C
I
0
6
4
3
P
C
I
0
6
4
3
E
S
S
1
8
7
8
S
M
3
8
8
1
3
M
6
3
7
7
8
7
3
3
8
C
D
-
R
O
M
F
D
D
P
A
R
A
L
L
E
L
P
O
R
T
S
E
R
I
A
L
P
O
R
T
F
I
R
P
A
R
A
L
L
E
L
P
O
R
T
S
E
R
I
A
L
P
O
R
T
H
D
D
P
C
M
C
I
A
C
R
T
L
C
D
V
I
D
E
O
R
A
M
I
N
T
E
R
N
A
L
K
B
P
S
2
T
O
U
C
H
P
A
D
L
2
C
A
C
H
E
1
6
M
B
R
A
M
D
I
M
M
*
1
H
O
S
T
B
U
S
B
I
O
S
$
C
P
U
_
D
(
6
3
:
0
)
$
C
P
U
_
A
(
3
1
:
3
)
$
C
P
U
_
D
(
6
3
:
0
)
$
C
P
U
_
A
(
1
7
:
3
)
$
C
P
U
_
D
(
6
3
:
0
)
$
C
P
U
_
A
(
3
1
:
3
)
A
D
(
3
1
:
0
)
$
M
D
(
6
3
:
0
)
$
M
A
(
1
1
:
0
)
A
D
(
3
1
:
0
)
A
D
(
3
1
:
0
)
A
D
(
3
1
:
0
)
A
D
(
3
1
:
0
)
A
D
(
3
1
:
0
)
A
D
(
3
1
:
0
)
S
D
(
1
5
:
0
)
S
D
(
1
5
:
0
)
S
D
(
1
5
:
0
)
S
D
(
1
5
:
0
)
S
D
(
1
5
:
0
)
S
A
(
1
1
:
0
)
S
A
(
9
:
0
)
S
A
2
S
A
(
9
:
0
)
Y
(
7
:
0
)
U
V
(
7
:
0
)
Y
(
7
:
0
)
U
V
(
7
:
0
)
R
D
A
T
A
#
,
W
D
A
T
A
#
S
A
(
1
6
:
0
)
,
L
A
(
2
3
:
1
7
)
M
E
D
I
A
B
A
Y
N
o
t
e
b
o
o
k
M
P
B
A
d
v
a
n
c
e
d
P
C
I
C
a
r
d
Theory of Operation 4-5
4.2.2 Memory Subsystem
The memory subsystem comprises the following components:
Main memory
L2 Secondary Memory (cache)
Flash ROM
The Extensa Series uses fast Extended Data Out (EDO) DRAM for main and video
memory and high-speed synchronous, pipelined burst SRAM for L2 cache memory.
Main BIOS and Video BIOS are stored in Flash ROM.
The Extensa 900 Series Memory Address Map is shown in Table 4-2.
Table 4-2 Memory Address Map
The DMA Channel Map is listed in Table 4-3.
Table 4-3 DMA Channel Map
4.2.2.1 Main Memory
The standard 900 Series notebook comes with 16 MB of Main memory installed on the
Main Board. Memory expansion accommodations are provided via a standard soDIMM
connector on the bottom of the Main Board Assembly. By installing a 64 MB soDIMM
module, the basic memory size can be expanded to a maximum of 80 MB.
Address Range Definition Function
000000 - 09FFFF 640 KB memory Base memory
0A0000 - 0BFFFF 128 KB video RAM Reserved for graphics display buffer
0C0000 - 0CBFFF Video BIOS Video BIOS
0E0000 - 0EFFFF
0F0000 - 0FFFFF
128 KB system BIOS System BIOS
System BIOS
100000 - FFFFFF Extended memory Onboard memory
FE0000 - FFFFFF 256 KB system ROM Duplicate of code assignment at 0E0000-0FFFFF
Controller Channel Address Function
1
1
1
1
2
2
2
2
0
1
2
3
4
5
6
7
0087
0083
0081
0082
Cascade
008B
0089
008A
Audio (option)
ECP/FIR/Audio
Diskette
ECP/FIR/Audio
Cascade
Spare
Spare
Spare
4-6 Theory of Operation
4.2.2.2 Flash ROM
All versions of the Extensa notebook family use a "Flash" ROM that contains both the
main system BIOS and the VGA BIOS. The Flash ROM contains "Boot Block" logic that
allows downloading new versions of BIOS without destroying the Boot Load area.
The Flash ROM execution is 8 bits wide. However, better performance can be attained
by enabling the Shadow ROM in the CMOS setup routine or by selecting the Windows
Control Panel Applet. When the Shadow ROM is enabled, BIOS is copied into a 32-bit,
high-speed system.
4.2.3 System Controller Function
The Extensa 900 Series notebook design uses two chips, the ALI M1521 (memory, Cache
and DRAM Controller for the Pentium System and the M1523 (PCI to ISA Bridge chip)
combine to provide the 586 system controller function for the new multimedia/
multithreading operating system, Windows 95.
The notebook utilizes the BGA package to improve the AC characterization, resolves
system bottleneck and make the system manufacturing easier. The system architecture
includes the UMA, ECC, PBSRAM, SDRAM/BEDO, and multi-bus with highly efficient,
deep FIFO between the buses, such as the HOST/PCI/ISA dedicated IDE bus.
The I/O Address Map for the 900 Series Notebook is provided in Table 4-4.
Theory of Operation 4-7
Table 4-4 I/O Address Map
Address Range Device
000 - 00F
020 - 021
022 - 023
040 - 043
048 - 04B
060 - 06E
070 - 071
080 - 08F
0A0 - 0A1
0C0 - 0DF
178 - 17A
1F0 - 1F7
170 - 177
3F6, 3F7
220 - 22F
240 - 24F
260 - 26F
280 - 28F
278 - 27F
2E8 - 2EF
2F8 - 2FF
378 - 37A
3B4, 3B5, 3BA
3C0 - 3C5
3C6 - 3C9
3C0 - 3CF
3D0 - 3DF
3E0 - 3E1
3E8 - 3EF
3F0 - 3F7
3F8 - 3FF
CF8 - CFF
DMA controller-1
Interrupt controller-1
M1523 registers
Timer 1
Timer 2
Keyboard controller
Real-time clock and NMI mask
DMA page register
Interrupt controller-2
DMA controller-2
6377 registers
Hard disk select
CD-ROM
Audio (option)
Audio (option) - default
Audio (option)
Audio (option)
Parallel port 1
COM 4
COM 2
Parallel port 2
Video subsystem
Video DAC
Enhanced graphics display
Color graphics adapter
PCMCIA controller
COM3
Floppy disk controller
COM 1
PCI configuration register
4-8 Theory of Operation
4.2.3.1 ALI M1521 (Memory, Cache and DRAM Controller)
The M1521 provides the system controller and data path components for the Extensa
900 Pentium-based system. It provides 64-bit CPU bus interface, 32-bit PCI bus
interface, 64/72 DRAM data bus with ECC or parity, secondary cache interface
including pipeline burst SRAM or asynchronous SRAM, PCI master to DRAM interface,
four PCI master arbiters, and a UMA arbiter. The M1521 bus interfaces are designed
to interface with 3V and 5V buses. It directly connects to 3V CPU bus, 3V or 5V tag,
3V or 5V DRAM bus, and 5V PCI bus.
4.2.3.1.1 Features of the ALI M1521
Supports all Intel/Cyrix
screwdriver
5 mm Nut Driver
Caution: All boards, options and peripherals contain components that are
sensitive to static electricity. When handling any of these items, protect
against static electricity by using wrist grounding straps and grounded
working mats. When moving or storing items, use the anti-static bags
supplied with the items.
6.4 Notebook FRUs
Table 6-1 lists and describes the various FRUs for the Extensa 990 Series. As shown
in Figure 6-1, all members of the Extensa 900 Series Notebook Computers contain two
major assemblies:
Notebook Assembly
- Cover-Display Assembly
- Base Assembly
Mobile Productivity Base Assembly
6-4 Field Service
Figure 6-1 Extensa 900 Series Assemblies
6.4.1 Cover-Display Assembly
The Cover-Display Assembly shown in Figure 6-2, contains the LCD screen, DC-AC
Inverter Board, DC-DC Inverter Board, bezel LCD cover and various other components
as listed in Table 6-1.
Mobile Productivity
Base Assembly
Notebook Assemblies
Cover-Display Assembly
Base Assembly
Field Service 6-5
.
Figure 6-2 Display FRUs
Table 6-1 Top Cover Assembly Field-Replaceable Units (FRUs)
FRU Description Assembly/
Disassembly
Paragraph
TI Part No.
PWB INVERTER, DSTN, EXT. 90X 6.5.19 9813635-0001
BEZEL, DISPLAY DSTN 12.1", EXT. 90X 6.5.17 9813636-0001
LCD PANEL, DSTN, 12.1",SHARP, EXT. 90X 6.5.18 9813637-0001
DISPLAY ASSY. DSTN, 12.1", SHARP, EXT. 90X 6.5.7 9813638-0001
CABLE, DISPLAY, DSTN, FJ, EXT. 90X 6.5.7 9813678-0001
PWB INVERTER, TFT, EXT. 90X 6.5.19 9813639-0001
BEZEL, DISPLAY TFT, FJ, EXT. 90X 6.5.17 9813640-0001
LCD PANEL, TFT, 11.3", FJ, EXT. 90X 6.5.18 9813641-0001
DISPLAY ASSY, TFT, 11.3", SHARP, EXT. 90X 6.5.7 9813642-0001
CABLE, INVERTER WIRE 12P, EXT. 900 6.5.19 9813680-0001
CN2
Latch Securing
Inverter Boards
DC-AC Inverter
Board Assembly
(large PWB)
LCD
Assembly
LCD Inverter
Board (smaller
PWB)
6-6 Field Service
6.4.2 System Base Assembly
As shown in Figure 6-3, the System Base Assembly houses a variety of field-replaceable
subassemblies and components. The various assemblies and reference paragraph
numbers containing removal/replacement procedures are listed in Table 6-2.
Figure 6-3 Notebook Base Assembly Major FRUs
Power Supply
Board
Battery Connector
Cable Assembly
Main Board
CPU
Board
Touchpad
Assembly
TOP Cover
VGA Video
Board
PC Card
Module
LED Board
Battery
Keyboard
Assembly
Microphone
LCD
Speaker
Speaker
Notebook with Keyboard
and Battery Removed
Heatsink
Assembly
Field Service 6-7
Table 6-2 Base Assembly Field-Replaceable Units (FRUs)
Base Assembly FRU Description Assembly/
Disassembly
Paragraph
TI Part No.
PWB Assemblies
PWB ASSY, MAIN BOARD W/O CPU, EXT. 90X 6.5.15 9813651-0001
PWB ASSY, VGA BOARD, EXT.90 X 6.5.11 9813652-0001
PWB ASSY, LED BOARD, EXT. 90X 6.5.8 9813653-0001
PWB ASSY, CPU BOARD, EXT. 90X 6.5.9 9813654-0001
PWB ASSY, DC-IN BOARD, EXT. 90X 6.5.13 9813655-0001
PWB ASSY, BATTERY BOARD, EXT. 90X 6.5.12 9813656-0001
PWB, POWER SUPPLY, EXT. 90X 6.5.12 9813643-0001
Keyboards
KEYBOARD, US, EXT. 90X 6.5.5 9813648-0001
KEYBOARD, UK, EXT. 900 6.5.5 9813648-0002
KEYBOARD, GER, EXT .900 6.5.5 9813648-0003
KEYBOARD, FRA, EXT. 900 6.5.5 9813648-0004
KEYBOARD, SPA, EXT. 900 6.5.5 9813648-0005
KEYBOARD, SWI/GER/FRA, EXT. 900 6.5.5 9813648-0006
KEYBOARD, ITA, EXT. 900 6.5.5 9813648-0007
KEYBOARD, POR, EXT. 900 6.5.5 9813648-0008
KEYBOARDS, SWE, EXT. 900 6.5.5 9813648-0010
KEYBOARD, DEN, EXT. 900 6.5.5 9813648-0012
KEYBOARD, NOR, EXT. 900 6.5.5 9813648-0013
KEYBOARD, FIN, EXT. 900 6.5.5 9813648-0014
KEYBOARD, BEL, EXT. 900 6.5.5 9813648-0015
KEYBOARD, CHI, EXT. 900 6.5.5 9813648-0019
KEYBOARD, KOR, EXT. 900 6.5.5 9813648-0020
Peripherals/Cables
HDD, 1.4GB, IBM, EXT.90X 6.5.4 9813645-0001
CABLE, FLEX, HDD, EXT.90X 6.5.4 9813644-0001
TOUCHPAD 6.5.16 9813516-0001
CABLE ASSY., TOUCHPAD, EXT. 90X 6.5.16 9813679-0001
6-8 Field Service
FDD, EXT. 90X Ref 9813649-0001
HDD BRACKET ASSY, EXT. 900 6.5.4 9813683-0001
Other Major Assemblies
CASE, UPPER, EXT. 90X 6.5.10 9813646-0001
CASE, LOWER, EXT. 90X 6.5.10 9813647-0001
BATTERY, LI-ION, EXT. 90X 6.5.1 9813633-0001
HEAT SINK, MAIN, EXT. 900 6.5.6 9813685-0001
AC ADAPTER, 45W, ADP-45HP, EXT. 6XX Ref 9813497-0004
PCMCIA MODULE, EXT. 900 6.5.14 9813716-0001
Service Manual Ref 9813715-0001
Dummy Battery (case only) EXT. 90X 6.5.1 9813717-0001
Doors, Access Covers, misc
COVER MEMORY, EXT. 900 2.3.1 9813663-0001
BRACKET HINGE, EXT. 900 Ref 9813664-0001
SPRING, EXT. SWP, EXT 900' SPG EXT SWP 0.2*2.0*17 Ref 9813665-0001
HINGE, RIGHT, EXT. 900 Ref 9813666-0001
HINGE, LEFT, EXT. 900 Ref 9813667-0001
KNOB BATTERY, EXT. 900 Ref 9813668-0001
COVER, HDD, EXT. 900 Ref 9813669-0001
TUBE FOR LCD ABS 072 EXT. 900 Ref 9813674-0001
BATTERY LOCK, RIGHT, EXT. 900 Ref 9813675-0001
BATTERY LOCK LEFT, EXT. 900 Ref 9813676-0001
DOOR SLIDE PC+FB 082 EXT. 900 Ref 9813677-0001
ASSY CORE UPPER CASE, EXT. 900 Ref 9813681-0001
HEAT PLATE ASSY., EXT. 900 6.5.6 9813682-0001
COVER, KEYBOARD, EXT. 900 6.5.5 9813684-0001
HOLDER ,TOUCHPAD, EXT.900 6.5.16 9813686-0001
SPRING LCD LOCK WPS EXT.900 Ref 9813687-0001
HOLDER DOCK CONNECTOR , EXT. 900 Ref 9813688-0001
RUBBER FOOT CR EXT.900 Ref 9813689-0001
Table 6-2 Base Assembly Field-Replaceable Units (FRUs)
Base Assembly FRU Description Assembly/
Disassembly
Paragraph
TI Part No.
Field Service 6-9
6.4.3 Mobile Productivity Base Assembly
The FRU list for the MPB is provided in Table 6-3. The major MPB FRUs are identified
in Figure 6-4.
TOUCHPAD, GND PLATE, EXT. 900 6.5.16 9813690-0001
CABLE, FLEX, LED BOARD, EXT. 90X 6.5.8 9813691-0001
Table 6-3 Mobile Productivity Base FRUs
FRU Description Assembly/
Disassembly
Paragraph
TI Part No.
PWB ASSY, CHARGER BOARD, MPB, EXT. 90X Ref 9813657-0001
CASE, BOTTOM, MPB, EXT. 90X Ref 9813658-0001
PWB ASSY, MAIN BOARD, MPB, EXT. 90X 6.6.7 9813661-0001
PWB ASSY, DC-IN BOARD, MPB, EXT. 90X 6.6.6 9813662-0001
PWB ASSY, BATTERY BOARD, EXT. 900
(same as used in Notebook)
Ref 9813656-0001
CASE, UPPER, MPB, EXT. 90X Ref 9813659-0001
CABLE ASSY, DOC, MPB, EXT. 90X Ref 9813660-0001
KNOB HAND LEVER LOCK, MPB, EXT. 900 Ref 9813670-0001
KNOB, MODULE LATCH, MPB, EXT. 900 Ref 9813671-0001
LOCK HAND LEVER, MPB, EXT. 900 Ref 9813672-0001
LATCH MODULE, MPB, EXT. 900 Ref 9813673-0001
CD-ROM DRIVE, EXT. 90X 6.6.1 9813650-0001
Table 6-2 Base Assembly Field-Replaceable Units (FRUs)
Base Assembly FRU Description Assembly/
Disassembly
Paragraph
TI Part No.
6-10 Field Service
Figure 6-4 Mobile Productivity Base Major FRUs
6.5 Notebook FRU Replacement Procedures
The following paragraphs contain field service-level removal/replacement procedures
for the 900 Series Notebook Computers.
Most FRU removal/replacement procedures involve connecting and disconnecting cable
connectors. The Extensa series uses two types of connectors including:
Locking-type connectors - Use a plastic stick to unlock and lock these type of
connectors as shown in Figure 6-5.
Non-locking connectors
MPB with Upper Cover
Removed
DC-DC Converter
Dock
Mechanism
Main Board
Assembly
Lever Release
Latch
Dock Release
Lever
Upper Cover of
Mobile Productivity Base
Field Service 6-11
Figure 6-5 Removing/Installing Cables with Locking-Type Connectors
6.5.1 Removing/Replacing the Notebook Battery Pack
Before performing any of the assembly/disassembly procedures, always disconnect the
AC adapter from the notebook and remove all battery packs. The procedure for removing
and replacing the notebook battery pack is as follows:
1. Turn off the computer and disconnect the AC adapter from the computer.
2. Unlock the battery on each side of the notebook and pull the battery out of
the front of the notebook as shown in Figure 6-6.
3. Replacement is essentially the reverse of Steps 1 and 2 (connector side of
battery goes up).
Unplugging the
Cable
Connecting the
Cable
6-12 Field Service
Figure 6-6 Notebook Battery Removal/Replacement
6.5.2 Removing/Replacing PCMCIA Options
The procedure for removing and replacing the PCMCIA options is as follows:
1. Turn off the computer and remove the battery pack(s) as described in
Paragraph 6.5.1.
2. Press the upper card eject button to eject the upper card, lower button
controls the lower card and use both buttons for Type III devices.
3. To replace the PCMCIA device, remove any filler cards present and insert the
device. Reinstall any external cabling required for the device.
Unlock the Battery
Pull Battery Out of Unit
Unlock Battery Pack
Remove Battery
from Front of Notebook
If Battery Lock comes off,
reinstall as shown
Flush
Slide
Field Service 6-13
Figure 6-7 Installing/Removing PCMCIA Options
6.5.3 Installing/Removing the Mobile Productivity Base
The procedure for removing and replacing the Mobile Productivity Base assembly is as
follows:
1. Power down the notebook and disconnect the AC adapter if installed.
2. Slide the lever release latch to the front of the MPB to release the docking
lever (refer to Figure 6-8).
3. Swing the Docking Lever outward a full 90 degrees from the side of the MPB.
6-14 Field Service
Figure 6-8 Removing/Replacing the MPB
4. The swing lever also pushes the computer up slightly off the MPB allowing
you to grasp the computer on the left hand side.
5. Lift the computer up slightly on the left hand side. Hold the computer securely
on both ends and pull the computer out of the MPB, left side first as shown
in Figure 6-8
6. Close the lever and close the expansion door on the bottom of the computer.
7. To replace the notebook in the MPB, turn the notebook over and open the
expansion door (slide the door toward the center of the notebook).
8. Slide the Release latch toward the front of the MPB to release the lever; then
swing the lever completely away from the MPB until the lever is 90 degrees
open from the side of the MPB.
Lever Release
Latch
Docking/
Undocking
Lever
Left Side
Right
Side
Field Service 6-15
9. Slide the computer into the MPB, right side first, ernsuring that the guides
on both the computer and the docking base are securely hooked; then rest
the computer on the base.
10. Press and hold down the computer; then swing the lever toward the MPB
until the latch release locks the computer in place.
6.5.4 Removing/Replacing the Hard Disk Drive Assembly
The procedure for removing and replacing the Hard Disk Drive assembly is as follows:
1. Power down the notebook, disconnect the AC adapter, if installed, and remove
the battery pack as described in Paragraphs 6.5.1 and 6.5.2.
2. Disconnect the Mobile Productivity Base and any installed PCMCIA options.
3. Turn the computer over and remove the hard disk drive bay cover (refer to
Figure 6-9).
4. Grasp the drive loop and remove the drive from the notebook.
Figure 6-9 Removing/Replacing the Hard Disk Drive Module
Drive
Removal
Loop
HDD
Access
Cover
6-16 Field Service
5. Store the HDD in an antistatic bag.
6. Replacement is the reverse of Steps 1 through 5.
6.5.5 Removing/Replacing the Keyboard Assembly
The procedure for removing and replacing the keyboard assembly is as follows:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Remove the four screws near the display hinges (rear of the notebook) as
shown in Figure 6-10.
3. Snap out and pull up the Status Panel (refer to Figure 6-10).
Figure 6-10 Removing the Keyboard Assembly
4. Lift up the Keyboard Assembly to free it from the notebook and then flip the
keyboard to the left side of the notebook as shown in Figure 6-10.
Lift up and flip
Keyboard to the left
3
Remove Status
Panel Screws
1
4
Unplug Keyboard
Connectors
2
Snap out and
pull up Status
Panel
Field Service 6-17
5. Unplug the keyboard connectors (CN5 and CN14) and set aside the Keyboard
Assembly.
6. Replacement is essentially the reverse of Steps 1 through 5.
6.5.6 Heat Sink Assembly Removal/Replacement
To remove and replace the Heat Sink Assembly, use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Remove the Keyboard Assembly as described in Paragraph 6.5.5.
3. Remove the four screws securing the Heat Sink Assembly to the notebook
and remove the heat sink.
4. Replacement of the Heat Sink Assembly is the reverse of Steps 1 through 3.
Figure 6-11 Heat Sink Assembly Removal/Replacement
1
Remove Keyboard
2
Remove four screws
and remove Heat Sink
Assembly
6-18 Field Service
6.5.7 Display Assembly Removal/Replacement
To remove and replace the Display Assembly, use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Remove the Keyboard Assembly as described in Paragraph 6.5.5.
3. Remove the Heat Sink Assembly as described in Paragraph 6.5.6.
4. Refer to Figure 6-12 and remove the two rear screws that secure the Display
to the notebook housing. Note: You dont have to remove the leftmost screw.
Figure 6-12 Removing/Replacing the Display Assembly
5. Remove the screw securing the Display Cable to the Main Board and unplug
the Display Cable (CN1) and the Inverter Cable (CN8).
6. Remove the Display Assembly from the Base Assembly.
7. Replacement is the reverse of Steps 1 through 6.
Remove Rear
Display Screws
1
CN8
CN1
2
Remove Display Cable
Screw And Unplug Two
Cables (CN1, CN8)
Field Service 6-19
6.5.8 Removing/Replacing the LED/Microphone Board
Assembly
To remove and replace the LED Board Assembly, use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Remove the Keyboard Assembly as described in Paragraph 6.5.5.
3. Remove the Heat Sink Assembly as described in Paragraph 6.5.6.
4. Remove the Display Assembly as described in Paragraph 6.5.7.
5. Remove the two screws that secure the LED Board Assembly and unplug
cable connector CN7; remove the LED Board Assembly.
6. Replacement is the reverse of Steps 1 through 5.
Figure 6-13 Removing/Replacing the LED/Microphone Board Assembly
1
Remove Keyboard
2 Remove Heat Sink
3
Remove two screws
and Connector CN7
CN7
6-20 Field Service
6.5.9 Removing/Replacing the CPU Board
To remove and replace the CPU Board Assembly, use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Remove the Keyboard Assembly as described in Paragraph 6.5.5.
3. Remove the Heat Sink Assembly as described in Paragraph 6.5.6.
4. Remove the screw securing the CPU Board to the Main Board and pull up to
remove the board from connector J1.
5. Replacement is the reverse of Steps 1 through 4.
Figure 6-14 CPU Board Assembly Removal/Replacement
J 1
1
Remove Keyboard and
Heat Sink Assemblies
2
Remove screw and
Cable Connector at J1
Field Service 6-21
6.5.10 Removing/Replacing the Top Cover
To remove and replace the Top Cover Assembly, use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Remove the Keyboard Assembly as described in Paragraph 6.5.5.
3. Remove the Heat Sink Assembly as described in Paragraph 6.5.6.
4. Remove the Display Assembly as described in Paragraph 6.5.7.
5. Remove four screws from the bottom of the base assembly.
6. Turn the base assembly over and remove Touchpad/Speaker connector
CN19.
7. Remove four screws from the four corners of the top cover (Figure 6-14).
8. Beginning from the left side of the unit, unsnap the top cover from the base
assembly.
9. Replacement is the reverse of Steps 1 through 8.
6-22 Field Service
Figure 6-15 Removing/Replacing the Top Cover
3
Unplug Speaker
Connector CN19 an
remove screws at fo
corners
1
2
Remove keyboard and
Heat Sink Assemblies
Remove four Screws
at Bottom of Main Unit
4
Beginning at left side,
unsnap top cover
from base assembly
Field Service 6-23
6.5.11 Removing/Replacing the VGA Video Board
To remove and replace the VGA Video Board Assembly, use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Remove the Keyboard Assembly as described in Paragraph 6.5.5.
3. Remove the Heat Sink Assembly as described in Paragraph 6.5.6.
4. Remove the Display Assembly as described in Paragraph 6.5.7.
5. Remove two screws and unplug the VGA Video Board from the Main Board
as shown in Figure 6-16.
6. Replacement is the reverse of Steps 1 through 5.
Figure 6-16 Removing/Replacing the VGA Video Board Assembly
1
Remove Keyboard,
Heat Sink and Top
Cover Assemblies
2 Remove Two Screws
and Unplug VGA Board
from Main Board
6-24 Field Service
6.5.12 Removing/Replacing the Power Supply Board
To remove and replace the Power Supply Board Assembly, use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Remove the Keyboard Assembly as described in Paragraph 6.5.5.
3. Remove the Heat Sink Assembly as described in Paragraph 6.5.6.
4. Remove the screw that secures the Power Supply Board Assembly to the Main
Board and remove the board from the base assembly.
5. Replacement is the reverse of Steps 1 through 4.
Figure 6-17 Removing/Replacing the VGA Video Board Assembly
CN1
CN22 and CN20
Power Supply
Board
Battery Connector
Cable Assembly
Field Service 6-25
6.5.13 Removing/Replacing the DC-In Board Assembly
To remove and replace the DC-In Board Assembly, use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Remove the Keyboard Assembly as described in Paragraph 6.5.5.
3. Remove the Heat Sink Assembly as described in Paragraph 6.5.6.
4. Unplug cable connectors CN9 and CN10 and remove the board.
5. Replacement is the reverse of Steps 1 through 4.
Figure 6-18 Removing/Replacing the DC-In Board Assembly
CN9
CN10
DC-In
Board
6-26 Field Service
6.5.14 Removing/Replacing the PC Card Module
To remove and replace the PC Card Module Assembly, use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Remove the Keyboard Assembly as described in Paragraph 6.5.5.
3. Remove the Heat Sink Assembly as described in Paragraph 6.5.6.
4. Remove the Display Assembly as described in Paragraph 6.5.7.
5. Remove the four screws that secure the PC Card Module to the Main Board
(refer to Figure 6-19).
6. Replacement is the reverse of Steps 1 through 5.
Figure 6-19 Removing/Replacing the PC Card Module
PC Module
Main Board
Assembly
Field Service 6-27
6.5.15 Removing/Replacing the Main Board Assembly
To remove and replace the Main Board Assembly, use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Remove the Keyboard Assembly as described in Paragraph 6.5.5.
3. Remove the Heat Sink Assembly as described in Paragraph 6.5.6.
4. Remove the Display Assembly as described in Paragraph 6.5.7.
5. Remove the Top Cover Assembly as described in Paragraph 6.5.10.
6. Remove fourteen screws from the bottom assembly as shown in Figure 6-20.
7. Remove the top cover as described in Paragraph 6.5.10.
8. Remove the Main Board Assembly.
9. Replacement is the reverse of Steps 1 through 8.
Figure 6-20 Removing/Replacing the Main Board Assembly
Main Board Assembly
6-28 Field Service
6.5.16 Removing Touchpad and Speakers
To remove and replace the Touchpad and Speakers, use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Remove the Keyboard Assembly as described in Paragraph 6.5.5.
3. Remove the Heat Sink Assembly as described in Paragraph 6.5.6.
4. Remove the Display Assembly as described in Paragraph 6.5.7.
5. Remove the Top Cover Assembly as described in Paragraph 6.5.10.
6. Remove the connectors on both sides of the Touchpad Assembly and detach
speakers from the top cover.
7. Remove the two screws that secure the Touchpad Assembly to the Top Cover
and remove the Button Assembly, Metal Plate, and Touchpad Main Sensor
as shown in Figure 6-21.
8. Replacement is the reverse of Steps 1-7.
Figure 6-21 Removing Touchpad Assembly
Button Assembly
Metal Plate
Touchpad
Connector
Field Service 6-29
6.5.17 Removing/Replacing the Display Bezel
To remove and replace the Display Bezel Assembly, use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Use a sharp object to remove the six bezel screw covers and remove the six
screws.
3. Pull out and remove the Display Bezel.
4. Replacement is the reverse of Steps 1 through 3.
Figure 6-22 Removing/Replacing the Display Bezel
6-30 Field Service
6.5.18 Removing/Replacing the LCD
To remove and replace the LCD, use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Remove the Display Bezel as described in Paragraph 6.5.17.
3. Remove three screws securing the LCD Assembly and pull up on the LCD
Panel (Figure 6-23).
4. Tilt the LCD Panel away from the display cover; unplug the LCD Panel from
the Display Cable Assembly (Figure 6-23) and remove the LCD Assembly.
5. Replacement is the reverse of Steps 1 through 4.
Figure 6-23 Removing/Replacing the LCD Assembly
Field Service 6-31
6.5.19 Removing/Replacing the Display Inverter Boards
To remove and replace the Display Inverter Boards, use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Remove the Display Bezel as described in Paragraph 6.5.17.
3. Gently fold back the foil around the display and unplug the inverter cable,
CN2.
4. Next, remove the screw securing the DC-AC Inverter Board (larger of the two
PWBs) and the LCD ID Board (smaller of the PWBs) to the display back cover.
5. Press down on the latch (refer to Figure 6-24) and remove the Inverter Boards.
6. Replacement is the reverse of Steps 1 through 5.
Figure 6-24 Removing/Replacing the Display Inverter Boards
CN2
6-32 Field Service
6.6 Removing/Replacing MPB FRUs
6.6.1 Removing/Replacing the Media Bay Device
To remove and replace a MPB Modular Bay Device (e.g., CD-ROM Drive or Floppy Disk
Drive), use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Unlatch the module by pressing the latch at the base of the MPB toward the
unlock icon (rear of MPB) (refer to Figure 6-25).
3. Simultaneously, grasp the recessed grip area on the module and pull module
out of the MPB.
4. Installation is the reverse of Steps 1 through 3.
Figure 6-25 Installing/Removing Media Bay Devices
CD-ROM
Drive
Modular Bay
Release
Latch
Mobile Productivity
Base
Field Service 6-33
6.6.2 Removing/Replacing the MPB Battery
To remove and replace an MPB battery pack or dummy battery pack, use the following
procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Using your thumbs, unlock the two battery locks at each side of the MPB
(refer to Figure 6-26).
3. Pull the module out of the MPB.
4. Installation is the reverse of Steps 1 through 3.
Figure 6-26 Installing/Removing Battery Pack in MPB
Unlocking the Battery
Battery Groove
Removing the Battery
6-34 Field Service
6.6.3 Removing/Replacing the MPB Housing
To remove and replace the MPB housing, use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Using your thumbs, unlock the two battery locks at each side of the MPB
(refer to Figure 6-26).
3. Pull the module out of the MPB.
4. Slide the Lever Release Latch forward to release the Docking Lever; extend
Docking Lever 90 degrees from the side of the MPB.
5. Remove fourteen screws from the top of the MPB as shown in Figure 6-27.
6. Lift up on the top section of the MPB Housing (from the left side as shown in
Figure 6-27) then pull to remove the top section of the MPB.
7. Replacement is the reverse of Steps 1 through 6.
Figure 6-27 Removing/Replacing the MPB Housing
A
Lever Release
Latch
Dock Release
Lever
Upper Cover of
Mobile Productivity Base
14 Screws
B
1
2
3
Remove Screws
Extend Dock
Release lever
Lift and Pull Out
Upper Cover
Field Service 6-35
6.6.4 Removing/Replacing the Docking Cable
To remove and replace the MPB Docking Cable, use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Using your thumbs, unlock the two battery locks at each side of the MPB
(refer to Figure 6-26); pull the battery pack out of the MPB.
3. Remove the MPB Housing as described in Paragraph 6.6.3.
4. Remove two screws securing the Docking Cable to release the assembly (refer
to Figure 6-28).
5. Remove the four screws securing the Docking Cable assembly to the Docking
Mechanism and remove the Docking Cable.
6. Replacement is essentially the reverse of Steps 1 through 5.
Figure 6-28 Removing/Replacing the MPB Docking Cable
Release Docking Cable
Remove Docking Cable Screws
6-36 Field Service
6.6.5 Removing/Replacing the Docking Mechanism
To remove and replace the MPB Docking Mechanism, use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Using your thumbs, unlock the two battery locks at each side of the MPB
(refer to Figure 6-26); pull the battery pack out of the MPB.
3. Remove the MPB Housing as described in Paragraph 6.6.3.
4. Remove the Docking Cable as described in Paragraph 6.6.4.
5. Remove the two screws that secure the Docking Mechanism to the bottom
section of the housing and remove the Docking Mechanism.
6. Replacement is the reverse of Steps 1 through 5.
Figure 6-29 Removing/Replacing the Docking Mechanism
Docking Mechanism
Field Service 6-37
6.6.6 Removing/Replacing the MPB DC-DC Converter
To remove and replace the MPB DC-DC Converter Assembly, use the following
procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Using your thumbs, unlock the two battery locks at each side of the MPB
(refer to Figure 6-26); pull the battery pack out of the MPB.
3. Remove the MPB Housing as described in Paragraph 6.6.3.
4. Remove the screw that secures the DC-DC Converter to the bottom section
of the MPB housing and remove the DC-DC-Converter.
5. Replacement is the reverse of Steps 1 through 4.
Figure 6-30 Removing/Replacing the MPB DC-DC Converter Board
DC-DC Converter
CN8, CN9
6-38 Field Service
6.6.7 Removing/Replacing the MPB Main Board Assembly
To remove and replace the MPB Main Board Assembly, use the following procedure:
1. Turn off the computer; disconnect the AC power adapter (if it is attached),
and remove the battery pack and PCMCIA cards as described in Paragraphs
6.5.1 and 6.5.2. Also disconnect the MPB (Paragraph 6.5.3) if attached.
2. Using your thumbs, unlock the two battery locks at each side of the MPB
(refer to Figure 6-26); pull the battery pack out of the MPB.
3. Remove the MPB Housing as described in Paragraph 6.6.3.
4. Remove the MPB Docking Cable and Docking Mechanism as described in
Paragraphs 6.6.4 and 6.6.5.
5. Remove the screw that secures the DC-DC Converter to the bottom section
of the MPB housing and remove the DC-DC-Converter.
6. Remove the DC-In and Battery Charger Cable Connectors (CN 13 and CN10).
7. Remove the 12 screws that secure the Main Board to the bottom section of
the housing. Then pull up on the main board and remove it from the unit.
8. Replacement is the reverse of Steps 1 through 7.
Figure 6-31 Removing/Replacing the MPB Main Board Assembly
CN13
CN10
12 Screws
Main Board
Assembly
Notebook Schematic Diagrams A-1
A
Notebook Schematic Diagrams
A.1 Introduction
This section contains schematic diagrams for the Extensa 900 Series Notebook
Computer. Logic schematics for the Mobile Productivity Base are provided in Appendix
B of this manual.
A-2 Notebook Schematic Diagrams
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 1 of 30)
Notebook Schematic Diagrams A-3
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 2 of 30)
A-4 Notebook Schematic Diagrams
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 3 of 30)
Notebook Schematic Diagrams A-5
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 4 of 30)
A-6 Notebook Schematic Diagrams
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 5 of 30)
Notebook Schematic Diagrams A-7
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 6 of 30)
A-8 Notebook Schematic Diagrams
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 7 of 30)
$MD32
$MD33
$MD34
$MD35
$MD36
$MD37
$MD38
$MD39
$CAS#4
$CAS#5
2
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
71
73
75
77
79
81
83
85
87
89
91
93
95
97
99
101
103
105
107
109
111
113
115
117
119
121
123
125
127
129
131
133
135
137
139
141
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
72
74
76
78
80
82
84
86
88
90
92
94
96
98
100
102
104
106
108
110
112
114
116
118
120
122
124
126
128
130
132
134
136
138
140
142
144 143
146
145
CN12
SDIMM144
$MA[0..11]
$MD[0..63]
$MD0
$MD1
$MD2
$MD3
$MD4
$MD5
$MD6
$MD7
$CAS#0
$CAS#1
$MD[0..63]
DRAM_VCC
DIMM SOCKET
2,6
2
2
2 $RAS#2
$RAS#3
$MWE#
$MD8
$MD9
$MD10
$MD11
$MD12
$MD13
$MD14
$MD15
$MA0
$MA1
$MA2
9
1
2
R202
100KR3
DIMM_IN#
$MD40
$MD41
$MD42
$MD43
$MD44
$MD45
$MD46
$MD47
$MA3
$MA4
$MA5
M+5V
23
19
MOS_ON#
ID_CLK
9 8
1
4
1
0
7
U51C
SOLCX125M
1
2
R154
100KR3
$MD48
$MD49
$MD50
$MD51
$MD52
$MD53
$MD54
$MD55
$MD56
$MD57
$MD58
$MD59
$MD60
$MD61
$MD62
$MD63
$MA7
$MA11
$CAS#6
$CAS#7
M+3.3V
M+3.3V
1 2
R81
2KR3
$MD16
$MD17
$MD18
$MD19
$MD20
$MD21
$MD22
$MD23
$MD24
$MD25
$MD26
$MD27
$MD28
$MD29
$MD30
$MD31
$MA6
$MA8
$MA9
$MA10
$CAS#2
$CAS#3
19 DIMM_DATA
2
C166
SCD1U
C167
SCD1U
C168
SCD1U
C169
SCD1U
C172
SCD1U
C179
SCD1U
C171
SC10U16V
1
2
R82
3K3R3
$CAS#[0..7]
$CAS#[0..7]
DRAM_VCC
C180
SCD1U
C176
SCD1U
C177
SCD1U
C178
SCD1U
DRAM_VCC
Notebook Schematic Diagrams A-9
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 8 of 30)
A-10 Notebook Schematic Diagrams
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 9 of 30)
Notebook Schematic Diagrams A-11
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 10 of 30)
A-12 Notebook Schematic Diagrams
Figure A-1 Motherboard PWB Logic Diagrams (Sheet 11 of 23 )
Notebook Schematic Diagrams A-13
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 12 of 30)
A-14 Notebook Schematic Diagrams
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 13 of 30)
4,14,15,17,19,20,25
20,23
1
2
R101
DUMMY-R3
SD[0..7]
@IRQ8#
IRQ#8
SD7
SD1
SD2
SD3
SD4
SD5
SD6
SD0
SD[0..7]
U40 PIN 22
4
23
19
19
VCC
24
CS$
13
AS
14
R/W$
15
DS
17
RST$
18
RCL$
21
EXTRAM
22
BC
20
X1
2
X2
3
AD7
11
AD6
10
AD5
9
AD4
8
AD3
7
AD2
6
AD1
5
AD0
4
INT$
19
SQW
23
MOT
1
VSS
12
VSS
16
U40
BQ3285E
1
2
R105
10KR3
2 1
G1
GAP-OPEN
1 2
RX13
DUMMY-R3
CX21
SCD1U
PWRGOOD#
RTCAS
RTCRW
RTCDS
PWRGOOD#
RTCAS
RTCRW
RTCDS
+5V +5V
RTC
SB: ADD DUMMY RESISTER TO
14 ENEXTCMOS
4 SA[0..15]
A0
12
A1
11
A2
10
A3
9
A4
8
A5
7
A6
6
A7
5
A8
27
A9
26
A10
23
A11
25
A12
4
A13
28
A14
29
A15
3
A16
2
CE
22
VCC
32
VSS
16
VPP
1
DQ0
13
DQ1
14
DQ2
15
DQ3
17
DQ4
18
DQ5
19
DQ6
20
DQ7
21
PGM
31
OE
24
A17/N.C
30
U45
S128K8-150
SA0
SA1
+5V
BIOS ROM
C213
SCD1U
1 2 3
4 5 6
D16
RB731U
SB:ADD 100KR3 FOR QUICK DISCHARGE
4
3
2
1
Q6
S2N3906
1
2
R147
10KR3
C226
SCD1U
1
2
RX21
100KR3
MEMW#
SD0
SD1
SD2
SD3
SD4
SD5
SD6
SD7
MEMW#
M+12V
4
19
19
MEMR#
XSA16
XSA17
SA2
SA3
SA4
SA5
SA6
SA7
SA8
SA9
SA10
SA11
SA12
SA13
SA14
SA15
MEMR#
4
25
1
2
3
1
4
7
U44A
SSHC32
RTCROMCS#
DISROM
RTCROMCS#
DISROM
+5V
19
3
1
2 Q7
RN1424
FLASH_ON
FLASH_ON
1 4
2 3
X4
CAN32768
1
2
BT1
BR1225-H1A
Notebook Schematic Diagrams A-15
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 14 of 30)
PIN1,4
ON
OFF
PASSWORD ENABLE
PASSWORD DISABLE
MATRIX1 KB TYPE
0
1
TYPE 0
TYPE 1
19
10
1
2
4
3
SW1
LSM702
1
2
R87
10KR3
1
2
R84
100KR3
HOTKEY#
3.3V/5V#
+5V
KBC_5V
D
Q
2
1
D
Q
1
2
D
Q
0
3
W
R
#
4
R
D
#
5
C
S
#
6
A
0
7
P
5
3
/
S
R
D
Y
#
8
P
5
2
/
S
C
L
K
9
P
5
1
/
T
X
D
1
0
P
5
0
/
R
X
D
1
1
P
4
7
/
I
N
T
4
1
2
P
4
6
/
I
N
T
3
1
3
P
4
5
/
I
B
F
0
#
/
O
B
F
1
1
4
P
4
4
/
O
B
F
0
1
5
P
4
3
/
I
N
T
2
1
6
P37
49
P36
50
P35
51
P34
52
P33
53
P32
54
P31
55
P30
56
VCC
57
P61/CNTR0
58
P60/INT5/OBF2
59
DQ7
60
DQ6
61
DQ5
62
DQ4
63
DQ3
64
P42/INT1
17
CNVSS
18
RESET#
19
P41/INT0
20
P40
21
XIN
22
XOUT
23
VSS
24
P27
25
P26
26
P25
27
P24
28
P23
29
P22
30
P21
31
P20
32
P
1
7
3
3
P
1
6
3
4
P
1
5
3
5
P
1
4
3
6
P
1
3
3
7
P
1
2
3
8
P
1
1
3
9
P
1
0
4
0
P
0
7
4
1
P
0
6
4
2
P
0
5
4
3
P
0
4
4
4
P
0
3
4
5
P
0
2
4
6
P
0
1
4
7
P
0
0
4
8
U28
M38813
1
2
RY1
47KR3
K
C
O
L
1
K
C
O
L
2
K
C
O
L
3
K
C
O
L
4
K
C
O
L
5
K
C
O
L
6
K
C
O
L
7
K
C
O
L
8
K
C
O
L
9
K
C
O
L
1
0
K
C
O
L
1
1
K
C
O
L
1
2
K
C
O
L
1
3
K
C
O
L
1
4
K
C
O
L
1
5
K
C
O
L
1
6
HOTKEY#
KBC_5V
M+5V
SC:ADD RY1 PULLED-UP
KEYBOARD CONTROLLER
4,13,15,17,19,20,25
C153
SCD1U
1 2
L12
SCHOKE-D
C154
SC1KP
SD[0..7]
KROW6
KROW7
KROW8
SD[0..7]
KBC_5V M+5V
4
4
4
20
26
26
13
IOW#
IOR#
SA2
@KBCS#
TDATA
TCLK
ENEXTCMOS
SD3
SD4
SD5
SD6
SD7
SD0
SD1
SD2
KROW1
KROW2
KROW3
KROW4
KROW5
SA2
IOR#
IOW#
TDATA
TCLK
@KBCS#
1
2
RX09
20KR3
CLLED#
NLLED#
CLLED#
NLLED#
IRQ1
IRQ12
B_SMB_DATA
B_SMB_CLK
KBCLK
KBDATA
+5V
M38813
SB: ADD 20K PULL-UP TO @SUSRST#
SB: ADD IRQ1 PULL-UP
4
4
10,11,15
21,26
21,26
28
28
1
3
2
X2
RESON-8MHZ
1
2
R83
DUMMY-R3
1
2
RX08
20KR3
1 2
R79
DUMMY-R3
1 2
R76
DUMMY-R3
IRQ1
IRQ12
@SUSRST#
KBCLK
KBDATA
SUSPEND#
KBC_5V
M+5V
20
27
27
21
21
1 2
1
4
7 1
3
U25A
SOHC4066
11 10
1
4
7 1
2
U25B
SOHC4066
1 2
RX26
470R3
1 2
RX27
470R3
SMB1_DATA
SMB1_CLK
SMB2_DATA
SMB2_CLK
+5VSB
SB: M+5V CHANGED TO +5VSB
SMB_SEL
B_SMB_DATA
B_SMB_CLK
23
21,26
21,26
1
3
5
7
2
4
6
8
CN5
ELCO-CONN8
KROW1
KROW3
KROW5
KROW7
KROW2
KROW4
KROW6
KROW8
ANYKEY
EN_213RI
PS2DATA
PS2CLK
ANYKEY
EN_213RI
PS2DATA
PS2CLK
1
2
3
4
5 6
7
8
9
10
RP21
SRP10K
KROW4
KROW1
KROW2
KROW3
KROW5
KROW6
KROW7
KROW8
KBC_5V KBC_5V
SMB_SEL=1 : SELECT SHIVA BATTERY
SMB_SEL=0 : SELECT UMA BATTERY
1
2
R68
100KR3
13 12
1
4
7
U61F
SSHC14
+5V
4 3
1
4
7 5
U25C
SOHC4066
8 9
1
4
7 6
U25D
SOHC4066
19
KCOL2
KCOL4
KCOL6
KCOL8
KCOL10
KCOL12
KCOL13
KCOL15
1
3
5
7
9
11
13
2
4
6
8
10
12
14
15
17
16
18
CN14
ELCO-CONN18
KCOL1
KCOL5
KCOL7
KCOL9
KCOL3
KCOL11
KCOL14
KCOL16
KCOL5
A-16 Notebook Schematic Diagrams
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 15 of 30)
16,22
16,22
16,22
16,22
16,22
16,22
16,21
ACK#
BUSY
PE
SLCT
SLCTIN#
INIT#
ERROR#
1 2 3 4
5 6 7 8
RP11
SRN33
1 2 3 4
5 6 7 8
RP12
SRN33
1
2
3
4 5
6
7
8
RP9
SRN33
1
2
3
4 5
6
7
8
RP10
SRN33
1 2
R42
33R3
PD[0..7]
I
R
Q
3
I
R
Q
4
I
R
Q
5
I
R
Q
6
I
R
Q
7
P
D
0
P
D
1
P
D
2
P
D
3
P
D
4
P
D
5
P
D
6
P
D
7
SUPER I/O CONTROLLER
4
16,21,22
16,22
IRQ[3..7]
STROB#
+5V
NOT INSTALLED
4
4
4,19
4
4
8
1 2
R52
100R3
C118
SC47P
C112
SCD1U
C125
SC39P
1
2
R57
47R3
RSTDRV
0WS#
DRQ2
DACK#2
TC
IRSL1
$SIO_24M
$SIO_24M
$SIO_24M
CS1/ZWS
1
DRQ2
2
DACK2
3
TC
4
X1
5
IRSL1
6
VSS
7
D7
8
D6
9
D5
10
D4
11
D3
12
D2
13
D1
14
D0
15
WR
16
RD
17
AEN
18
A9
19
A8
20
A7
21
A6
22
A5
23
A4
24
A3
25
A
2
2
6
A
1
2
7
A
0
2
8
A
1
0
2
9
D
S
K
C
H
G
3
0
D
R
Q
1
3
1
H
D
S
E
L
3
2
R
D
A
T
A
3
3
W
P
3
4
T
R
K
0
3
5
W
G
A
T
E
3
6
W
D
A
T
A
3
7
S
T
E
P
3
8
D
I
R
3
9
V
S
S
4
0
M
T
R
1
/
I
D
L
E
/
I
R
S
L
2
4
1
D
R
0
4
2
D
R
1
/
P
D
4
3
M
T
R
0
4
4
I
N
D
E
X
4
5
D
E
N
S
E
L
/
A
D
R
A
T
E
1
4
6
D
R
V
2
/
P
N
F
/
D
R
2
3
/
S
I
R
Q
1
3
/
I
R
S
L
2
4
7
V
D
D
4
8
D
R
A
T
E
1
/
M
S
E
N
1
/
C
S
0
/
S
I
R
Q
I
2
/
D
A
C
K
3
4
9
D
R
A
T
E
0
/
M
S
E
N
0
5
0
IOCHRDY
51
DACK1
52
DACK0
53
DRQ0
54
IRQ9
55
IRQ10
56
IRQ11
57
IRQ15/SIRQI1/DRQ3
58
VSS
59
RI2/A11
60
DTR2/A12
61
CTS2/A13
62
SOUT2/BOUT2/CFG0/IRTX
63
RTS2/A14
64
SIN2/IRRX1
65
DSR2/IRQ12/IRRX2/IRSL0
66
DCD2/A15
67
RI1
68
DTR1
69
CTS1
70
SOUT1/BOUT1/BADDR1
71
RTS1/BADDR0
72
SIN1
73
DSR1
74
DCD1
75
A
F
D
/
D
S
T
R
B
/
D
E
N
S
E
L
7
6
E
R
R
/
H
D
S
E
L
7
7
I
N
I
T
/
D
I
R
7
8
S
L
I
N
/
S
T
E
P
/
A
S
T
R
B
7
9
S
L
C
T
/
W
G
A
T
E
8
0
P
E
/
W
D
A
T
A
8
1
B
U
S
Y
/
W
A
I
T
/
M
T
R
1
8
2
A
C
K
/
D
R
1
8
3
P
D
7
/
M
S
E
N
1
8
4
P
D
6
/
D
R
A
T
E
0
8
5
P
D
5
/
M
S
E
N
0
8
6
P
D
4
/
D
S
K
C
H
G
8
7
V
S
S
8
8
P
D
3
/
R
D
A
T
A
8
9
P
D
2
/
W
P
9
0
P
D
1
/
T
R
K
0
9
1
P
D
0
/
I
N
D
E
X
9
2
S
T
B
/
W
R
I
T
E
9
3
I
R
Q
7
9
4
I
R
Q
6
9
5
I
R
Q
5
/
A
D
R
A
T
E
0
9
6
V
D
D
9
7
I
R
Q
4
9
8
I
R
Q
3
9
9
M
R
1
0
0
U23
PC87338VJG
SD7
SD6
SD5
SD4
SD3
SD2
SD1
SD0
PC87338
4
4
4
4,19
4,19
16
16
16
16
20
20
2
1MR3
IRQ11
IRQ10
IRQ9
DRQ0
AUTOFD#
IRRX1
IRRX2
IRTX
DRQ3 SA[11..15]
DCD1#
RI1#
SA15
SA14
SA13
SA12
SA11
IRTX
SOUT1
RTS1#
SIN1
DSR1#
RI1#
CTS1#
DTR1#
4
4
4
4
4
16
22
22
22
C151
SCD1U
C159
SC1KP
C155
SC10U16V
DACK#0
DACK#1
IOCHRDY#
+5V
4,19
22
22
22
22
22
22
DACK#3
PNF
DR0#
IRSL2 DRQ1
RPM
INDEX#
MTR0#
WGATE#
TRK0#
WRTPRT#
RDATA#
HDSEL
DSKCHG#
SA9
SA8
SA7
SA6
SA5
SA4
SA3
SA2
SA1
SA0
SA10
MTR0#
4
4
4
4
4,13,14,17,19,20,25 SD[0..7]
IOW#
IOR#
AEN
SA[0..10]
22
22
22
FDIR
STEP#
WDATA#
SB: CHANGE MAX213 TO MAX3243
16,21
16,21
16,21
16,21
16,21
16
16,21
16,21
C81
SCD1U
C82
SCD1U
C1+
28
C1-
24
C2+
1
C2-
2
T1IN
14
T2IN
13
T3IN
12
R2OUTB
20
R1OUT
19
R2OUT
18
R3OUT
17
R4OUT
16
R5OUT
15
FORCEON
23
FORCEOFF#
22
INVALID#
21
V+
27
V-
3
T1OUT
9
T2OUT
10
T3OUT
11
R1IN
4
R2IN
5
R3IN
6
R4IN
7
R5IN
8
GND
25
VCC
26
U7
MAX3243
PSOUT1
PRTS1#
PDTR1#
PSIN1
PDSR1#
PCTS1#
PRI1#
PDCD1#
M+5V
14
20,23
20
C61
SCD1U
C62
SCD1U
SUSPEND#
@RI1#
@DCD1#
SOUT1
RTS1#
SIN1
DSR1#
CTS1#
DTR1#
1
RX35
CX13
SCD1U
Notebook Schematic Diagrams A-17
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 16 of 30)
A-18 Notebook Schematic Diagrams
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 17 of 30)
)
Notebook Schematic Diagrams A-19
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 18 of 30)
A-20 Notebook Schematic Diagrams
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 19 of 30)
)
Notebook Schematic Diagrams A-21
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 20 of 30)
A-22 Notebook Schematic Diagrams
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 21 of 30)
Notebook Schematic Diagrams A-23
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 22 of 30)
A-24 Notebook Schematic Diagrams
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 23 of 30)
Notebook Schematic Diagrams A-25
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 24 of 30)
A-26 Notebook Schematic Diagrams
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 25 of 30)
4
4
4 IRQ14
IRQ15
IRQ12
RSTDRV
+5V
1
2
3
4
5 6
7
8
9
10
RP48
SRP10K
MEMR#
MEMW#
IOR#
IOW#
+5V
4,19
4,19
4,19
1
2
3
4
5 6
7
8
9
10
RP36
SRP4K7
1
2
3
4 5
6
7
8
RP41
SRN100K
DRQ1
DRQ3
DRQ2
DRQ1
DISROM
DRQ3
DRQ2
+5V
4
4
4
4,19
4,19
4,19
4,19 DRQ0
DRQ5
DRQ6
DRQ7
MEMCS16#
IOCS16#
REFRESH#
DRQ0
DRQ5
DRQ6
DRQ7
MEMCS16#
IOCS16#
REFRESH#
SD4
SD5
SD6
SD7
+5V
1
2
3
4
5 6
7
8
9
10
RP49
SRP10K
SD0
SD1
SD2
SD3
+5V
1
2
3
4
5 6
7
8
9
10
RP46
SRP100K
1
2
3
4
5 6
7
8
9
10
RP47
SRP100K
SD8
SD9
SD10
SD11
LA19
LA18
LA17
SBHE#
+5V
+5V
LA22
LA21
LA20
SD12
SD13
SD14
SD15
LA23
+5V
+5V
SD3
SD4
+5V
B1
1
B2
2
B3
3
B4
4
B5
5
B6
6
B7
7
B8
8
B9
9
B10
10
B11
11
B12
12
B13
13
B14
14
B15
15
B16
16
B17
17
B18
18
B19
19
B20
20
B21
21
B22
22
B23
23
B24
24
B25
25
B26
26
B27
27
B28
28
B29
29
B30
30
B31
31
B32
32
B33
33
B34
34
B35
35
B36
36
B37
37
B38
38
B39
39
B40
40
A1
41
A2
42
A3
43
A4
44
A5
45
A6
46
A7
47
A8
48
A9
49
A10
50
A11
51
A12
52
A13
53
A14
54
A15
55
A16
56
A17
57
A18
58
A19
59
A20
60
A21
61
A22
62
A23
63
A24
64
A25
65
A26
66
A27
67
A28
68
A29
69
A30
70
A31
71
A32
72
A33
73
A34
74
A35
75
A36
76
A37
77
A38
78
A39
79
A40
80
GF1
MS-DBG-GF80
SD[0..15]
+5V
DEBUG-BD GOLDEN FINGER
4
4
4
4
4
4
4
4
4
4
4
4
4
13
19
23
RSTDRV
IOCHRDY#
AEN
IOW#
IOR#
BALE
IRQ11
LA20
LA21
LA22
LA23
MEMR#
MEMW#
DISROM
FLASH_ON
PWRGIN
SD7
SD8
SD9
SD10
SD11
SD12
SD13
SD14
SD15
PWRGIN
FLASH_ON
DISROM
MEMW*
MEMR*
LA20
LA21
LA22
LA23
IRQ11
BALE
IOR#
IOW#
AEN
IOCHRDY#
RSTDRV
4
4
4
4
4
19
19
RTCROMCS#
XSA17
XSA16
SBHE#
LA19
LA18
LA17
SD0
SD1
SD2
SA0
SA1
SA2
SA3
SA4
SA5
SA6
SA7
SA8
SA9
SA10
SA11
SA12
SA13
SA14
SA15
SA16
MEMW#
MEMR#
RTCROMCS#
XSA17
XSA16
SBHE#
LA19
LA18
LA17
4 IOCHK#
IOCHRDY# 1 2
R258
1KR3
1 2
R263
10KR3
+5V
+5V
4
4
4
4 IRQ6
IRQ5
IRQ4
IRQ3
IRQ3
IRQ4
IRQ5
IRQ6
+5V
4
4
4
1
2
3
4
5 6
7
8
9
10
RP45
SRP10K
IRQ10
IRQ9
IRQ7
IRQ11
IRQ10
IRQ7
IRQ9
+5V
4
SA[0..16]
SA[0..16]
SD5
SD6
Notebook Schematic Diagrams A-27
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 26 of 30)
1 2
L9
MLB321611
1 2 3 4
5 6 7 8
RP3
SRN10K
1 2
F1
SPOLY100
+5V
PS2 INTERFACE
14,21
14,21
14,21
14,21
PS2DATA
PS2CLK
KBCLK
KBDATA
C79
SC47P
1 2
R1
47R3
1 2
R2
47R3
1 2
R4
47R3
1 2
R3
47R3
1 2
L4
MLB321611
1 2
L5
MLB321611
1 2
L7
MLB321611
1 2
L6
MLB321611
1
2
3
4
5
6
7
8
CN9
SD5339810-6
C78
SC47P
C77
SC47P
C76
SC47P
14 TDATA
18
18
14
1
3
5
7
9
11
13
2
4
6
8
10
12
14
15 16
17 18
CN19
SD5255917-14
1 2 3 4
5 6 7 8
RP31
SRN10K
SPK_L1
SPK_R1
TCLK
+5V
+5V
TOUCHPAD CONNECTOR
SB: CHANGE CN19 PIN DEFINITION
C234
SC47P
C224
SC47P
AUD_GND
A-28 Notebook Schematic Diagrams
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 27 of 30)
13 12
1
4
7
U86F
SSHC14
+5VSB 1
2
R253
47KR3
AD+
+5VSB
1 2
R252
150KR3
3
1
2 Q9
RN1424
AD_IN#
ADAPTOR PLUG-IN DETECTION CIRCUIT
23 AD5V
AD5V
C351
SCD1U
C352
SC1KP
+5VSB
+5VSB
CHARGER INTERFACE CIRCUIT
14
14
1
2
3
4
5
6
7
8
CN21
MOLEX-CON8
SMB1_CLK
SMB1_DATA
BAT_TH
BAT_VS
BAT+
BATTERY CONNECTOR
SMB1_CLK, SMB1_DATA: CHARGER SMB I2C
19
21
28
1
3
5
7
9
11
13
15
17
19
2
4
6
8
10
12
14
16
18
20
CN22
MOLEX-CONN20A
1
2
R251
10KR3
CSO CSI
CHARGE_LED
CHGR_CLK CHGR_DATA
BAT_TH
SMB1_CLK SMB1_DATA
BAT_VS
+5VSB
BAT+ BAT+
CSI, CSO:CHARGER HANDSHAKING
SIGNALS
19
21
2 1
D28
NSQ03A04-1
DCBATOUT
ADAPTOR/BATTERY INTERFACE
AD+
1 2
R242
560R3
1
2
3
D22
BAV99
DK_ADBATON
BL3#
DCBATOUT
1
2
3
4
8
7
6
5
U94
SI4435DY
2 1
D27
NSQ03A04-1
1
2
3
Q13
2N7002
1 2
RY16
4K7R3
2
1
DY6
MBR0540T1
1
2
R270
240KR3
1
2
R269
100KR3
1
3
DY1
BZX84C4V3L
BAT+
CY13
SCD1U50V3ZY
330KR3
82KR3
1 2
RY23
220KR3
1
2
3
QY1
2N7002
2.2KR3
CY14
SCD1U50V3ZY
CHGR_CLK,CHGR_DATA: CHARGER SEEPROM'S CLOCK & DATA
19 BL1#
+5VSB
+5V
19
1
3
5
7
9
11
13
15
17
19
2
4
6
8
10
12
14
16
18
20
CN20
MOLEX-CONN20A
BL2#
DCBATOUT DCBATOUT
AD+
CHARGER SEEPROM
ADDRESS SELECT
SHIVA:PULL LOW(ADDRESS 0)
UMA:OPEN(ADDRESS 1)
INTERNAL PULLED HIGH AT CHARGER BOARD
29
1
2
R272
0R3
ON/OFF#
CHARGER CONNECTOR
6/18 MOVE BL3# FROM PIN 10 TO PIN 16
AD5V
BL3#
CHARGER CONNECTOR
Notebook Schematic Diagrams A-29
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 28 of 30)
C73
SCD1U
+5V
C74
SCD1U
C72
SCD1U
M+5V +5VSB
LED INTERFACE
21 27
3
1
2 Q1
RN1424
CHARGE_LED
3
1
2 Q2
RN1424
DK_CHG_LED
CHARGE_LED#
14
14
20
CLLED#
NLLED#
@COVER_SW
COVER_SW
CHARGE_LED#
NLOCK_LED#
CLOCK_LED#
M+5V
+5VSB
SB: ADD LOWBAT_LED
19
29
1
3
5
7
9
11
13
2
4
6
8
10
12
14
15
17
19
16
18
20
CN7
SD5255917-16
POWER_SW2
LOWBAT_LED
POWER_SW2
STANDBY_LED#
HDD/FDD_LED#
+5V
MIC_R
AUD_GND
18 INTMIC
19
21
24
1
2
R141
10KR3
HDD_LED#
DK_DISKLED#
HDD/FDD_LED#
+5V
CLOSE TO CONNECTOR
CLOSE TO AUDIO CHIP
19
C59
SC1U10V5JY
9 8
1
4
7
U8D
SSHC14
12 11
1
4
1
3
7
U56D
SSHC125
STNDBY#
STANDBY_LED#
+5V +5V
1
2
R14
2MR5
1
2
D7
S1N4148
1
2
R26
220KR3
11 10
1
4
7
U8E
SSHC14
+5V
A-30 Notebook Schematic Diagrams
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 29 of 30)
Notebook Schematic Diagrams A-31
Figure A-1 Notebook Main Board Logic Diagrams (Sheet 30 of 30)
3 4
1
4
7
U11B
SSHC14
M+5V
11 10
1
4
7
U34E
SSHC14
13 12
1
4
7
U34F
SSHC14
1 2
1
4
7
U11A
SSHC14
M+5V M+5V M+5V
11 10
1
4
7
U53E
SSHC14
13 12
1
4
7
U53F
SSHC14
+5V +5V
13 12
1
4
7
U8F
SSHC14
9 8
1
4
7
U12D
SSHC14
13 12
1
4
7
U19F
SSHCT04
+5V +5V +5V
+5V
11 10
1
4
7
U1E
SSHC14
13 12
1
4
7
U1F
SSHC14
M+5V M+5V
9
10
8
1
4
7
U67C
SSHC32
4
5
6
1
4
7
U67B
SSHC32
1
2
3
1
4
7
U54A
SSHC08
9
10
8
1
4
7
U91C
SSHC08
M+5V M+5V
+5V +5VSB
12
13
11
1
4
7
U67D
SSHC32
1
2
3
1
4
7
U14A
TSHCT00
D
2
CLK
3
Q
5
Q
6
VCC
14
P
R
4
GND
7 C
L
1
U64A
SSHCT74
M+5V
+5V
12
13
11
1
4
7
U91D
SSHC08
+5VSB
+5V
M+3.3V
8 9
1
4
7 6
U75D
SOHC4066
M+3.3V M+3.3V M+3.3V
AUDIO_+5VA
AUD_GND
D
12
CLK
11
Q
9
Q
8
VCC
14
P
R
1
0
GND
7 C
L
1
3
U43B
SSHC74
12
13
11
1
4
7
U48D
SSHC08
+5V
+5V
M+3.3V
+5V
9 8
1
4
1
0
7
U62C
SOLCX125M
12 11
1
4
1
3
7
U62D
SOLCX125M
2 3
1
4 1
7
U51A
SOLCX125M
5 6
1
4 4
7
U51B
SOLCX125M
12 11
1
4
1
3
7
U51D
SOLCX125M
1 2
1
4
7
U34A
SSHC14
M+5V
MPB Schematic Diagrams B-1
B
MPB Schematic Diagrams
B.1 Introduction
This section contains schematic diagrams for the Extensa 900 Mobile Productivity Base.
Logic schematics for the MPB are provided in Appendix A of this manual.
B-2 MPB Schematic Diagrams
P
Figure B-1 MPB CPU Board Logic Diagrams (Sheet 1 of 3)
V
C
C
_
C
P
U
C
5
1
S
C
2
2
U
1
0
V
0
J
Y
C
4
5
S
C
2
2
U
1
0
V
0
J
Y
C
4
6
S
C
2
2
U
1
0
V
0
J
Y
C
5
4
S
C
2
2
U
1
0
V
0
J
Y
C
3
7
S
C
2
2
U
1
0
V
0
J
Y
C
5
0
S
C
2
2
U
1
0
V
0
J
Y
C
4
4
S
C
2
2
U
1
0
V
0
J
Y
C
4
8
S
C
2
2
U
1
0
V
0
J
Y
C
2
0
S
C
2
2
U
1
0
V
0
J
Y
C
2
7
S
C
2
2
U
1
0
V
0
J
Y
C
4
9
S
C
2
2
U
1
0
V
0
J
Y
C
3
4
S
C
2
2
U
1
0
V
0
J
Y
1
2
3
4
5
6
7
8
9
1
0
1
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
2
0
2
1
2
2
2
3
2
4
2
5
2
6
2
7
2
8
2
9
3
0
3
1
3
2
3
3
3
4
3
5
3
6
3
7
3
8
3
9
4
0
4
1
4
2
4
3
4
4
4
5
4
6
4
7
4
8
4
9
5
0
5
1
5
2
5
3
5
4
5
5
5
6
5
7
5
8
5
9
6
0
6
1
6
2
6
3
6
4
6
5
6
6
6
7
6
8
6
9
7
0
7
1
7
2
7
3
7
4
7
5
7
6
7
7
7
8
7
9
8
0
8
1
8
2
8
3
8
4
8
5
8
6
8
7
8
8
8
9
9
0
9
1
9
2
9
3
9
4
9
5
9
6
9
7
9
8
9
9
1
0
0
J
1
A
W
R
2
0
0
P
V
F
W
A
1
V
C
C
_
3
V
C
5
3
S
C
1
K
P
C
1
8
S
C
1
K
P
1
3
2
N
F
2
S
T
C
2
2
2
B
1
3
2
N
F
3
S
T
C
2
2
2
B
C
P
U
_
V
C
C
C
1
5
S
C
1
K
P
C
3
3
S
C
1
K
P
$
N
M
I
$
C
P
U
_
A
2
5
$
C
P
U
_
A
2
6
$
C
P
U
_
A
2
7
$
C
P
U
_
A
2
8
$
C
P
U
_
A
3
$
C
P
U
_
A
4
$
C
P
U
_
A
5
$
C
P
U
_
A
6
$
C
P
U
_
A
7
$
C
P
U
_
A
8
$
C
P
U
_
A
9
$
C
P
U
_
A
3
1
$
C
P
U
_
A
1
0
$
C
P
U
_
A
1
1
$
C
P
U
_
A
1
2
$
C
P
U
_
A
1
3
$
C
P
U
_
A
1
4
$
C
P
U
_
A
1
5
$
C
P
U
_
A
1
6
$
C
P
U
_
A
1
7
$
C
P
U
_
A
1
8
$
C
P
U
_
A
1
9
$
C
P
U
_
A
2
0
2
$
M
I
O
#
$
D
C
#
$
W
R
#
$
B
R
D
Y
#
$
I
G
N
N
E
#
$
F
E
R
R
#
$
C
P
U
A
D
S
#
C
P
U
_
I
D
0
C
P
U
_
I
D
1
C
P
U
_
I
D
2
C
P
U
_
I
D
3
C
P
U
_
V
O
L
T
0
C
P
U
_
V
O
L
T
1
C
P
U
_
V
E
N
D
$
I
N
V
C
P
U
_
T
H
M
C
P
U
_
T
H
M
G
$
C
P
U
_
A
3
0
$
C
P
U
_
A
2
9
$
C
P
U
_
A
2
1
$
C
P
U
_
A
2
2
$
C
P
U
_
A
2
3
$
C
P
U
_
A
2
42
22
2 22
2 3 3 3 3
3 3
3
2
3
3
$
A
H
O
L
D
$
A
2
0
M
#
$
E
A
D
S
#
$
I
N
T
R
$
K
E
N
#
$
N
A
#
$
S
M
I
A
C
T
#
$
B
O
F
F
#
$
C
A
C
H
E
#
$
H
I
T
M
#
$
H
L
O
C
K
#
$
H
O
L
D
$
H
L
D
A
$
W
B
/
W
T
#
22 2
2 2
2
2
2 2 22
22
2
$
C
P
U
C
L
K
$
C
P
U
I
N
I
T
$
C
P
U
R
S
T
$
S
M
I
#
$
S
T
P
C
L
K
#
$
B
E
#
7
$
B
E
#
6
$
B
E
#
5
$
B
E
#
4
$
B
E
#
3
$
B
E
#
2
$
B
E
#
1
$
B
E
#
0
2
2
,
3
2
,
3
2
2
$
C
P
U
_
A
[
3
.
.
3
1
]
$
B
E
#
[
0
.
.
7
]
2
2
C
3
8
S
C
2
2
U
1
0
V
0
J
Y
1
3
2
N
F
1
S
T
C
2
2
2
B
V
C
C
_
3
V
C
3
2
S
C
1
K
P
C
1
4
S
C
1
K
P
C
3
S
C
2
2
U
1
0
V
0
J
Y
V
C
C
_
I
/
O
C
P
U
B
O
A
R
D
C
O
N
N
E
C
T
O
R
|
L
I
N
K
|
C
P
U
1
.
S
C
H
|
C
P
U
2
.
S
C
H
C
P
U
_
V
C
C
1
0
1
1
0
2
1
0
3
1
0
4
1
0
5
1
0
6
1
0
7
1
0
8
1
0
9
1
1
0
1
1
1
1
1
2
1
1
3
1
1
4
1
1
5
1
1
6
1
1
7
1
1
8
1
1
9
1
2
0
1
2
1
1
2
2
1
2
3
1
2
4
1
2
5
1
2
6
1
2
7
1
2
8
1
2
9
1
3
0
1
3
1
1
3
2
1
3
3
1
3
4
1
3
5
1
3
6
1
3
7
1
3
8
1
3
9
1
4
0
1
4
1
1
4
2
1
4
3
1
4
4
1
4
5
1
4
6
1
4
7
1
4
8
1
4
9
1
5
0
1
5
1
1
5
2
1
5
3
1
5
4
1
5
5
1
5
6
1
5
7
1
5
8
1
5
9
1
6
0
1
6
1
1
6
2
1
6
3
1
6
4
1
6
5
1
6
6
1
6
7
1
6
8
1
6
9
1
7
0
1
7
1
1
7
2
1
7
3
1
7
4
1
7
5
1
7
6
1
7
7
1
7
8
1
7
9
1
8
0
1
8
1
1
8
2
1
8
3
1
8
4
1
8
5
1
8
6
1
8
7
1
8
8
1
8
9
1
9
0
1
9
1
1
9
2
1
9
3
1
9
4
1
9
5
1
9
6
1
9
7
1
9
8
1
9
9
2
0
0
J
1
B
W
R
2
0
0
P
V
F
W
A
1
$
C
P
U
_
D
1
6
$
C
P
U
_
D
1
7
$
C
P
U
_
D
1
8
$
C
P
U
_
D
1
9
$
C
P
U
_
D
2
0
$
C
P
U
_
D
2
1
$
C
P
U
_
D
2
2
$
C
P
U
_
D
2
3
$
C
P
U
_
D
2
4
$
C
P
U
_
D
2
5
$
C
P
U
_
D
2
6
$
C
P
U
_
D
2
7
$
C
P
U
_
D
2
8
$
C
P
U
_
D
2
9
$
C
P
U
_
D
3
0
$
C
P
U
_
D
3
1
$
C
P
U
_
D
3
2
$
C
P
U
_
D
3
3
$
C
P
U
_
D
5
0
$
C
P
U
_
D
5
1
$
C
P
U
_
D
5
2
$
C
P
U
_
D
5
3
$
C
P
U
_
D
5
4
$
C
P
U
_
D
5
5
$
C
P
U
_
D
5
6
$
C
P
U
_
D
5
7
$
C
P
U
_
D
5
8
$
C
P
U
_
D
5
9
$
C
P
U
_
D
6
0
$
C
P
U
_
D
6
1
$
C
P
U
_
D
6
2
$
C
P
U
_
D
6
3
$
C
P
U
_
D
3
4
$
C
P
U
_
D
3
5
$
C
P
U
_
D
3
6
$
C
P
U
_
D
3
7
$
C
P
U
_
D
3
8
$
C
P
U
_
D
3
9
$
C
P
U
_
D
4
0
$
C
P
U
_
D
4
1
$
C
P
U
_
D
4
2
$
C
P
U
_
D
4
3
$
C
P
U
_
D
4
4
$
C
P
U
_
D
4
5
$
C
P
U
_
D
4
6
$
C
P
U
_
D
4
7
$
C
P
U
_
D
4
8
$
C
P
U
_
D
4
9
C
P
U
_
V
O
L
T
A
G
E
1
C
P
U
_
V
O
L
T
A
G
E
2
C
P
U
_
V
O
L
T
A
G
E
3
C
P
U
_
V
O
L
T
A
G
E
4
12
R
2
8
0
R
3
12
R
2
9
0
R
3
12
R
3
0
0
R
3
12
R
3
1
0
R
3
F
O
R
S
H
I
V
A
S
B
$
C
P
U
_
D
0
$
C
P
U
_
D
1
$
C
P
U
_
D
2
$
C
P
U
_
D
3
$
C
P
U
_
D
4
$
C
P
U
_
D
5
$
C
P
U
_
D
6
$
C
P
U
_
D
7
$
C
P
U
_
D
8
$
C
P
U
_
D
9
$
C
P
U
_
D
1
0
$
C
P
U
_
D
1
1
$
C
P
U
_
D
1
2
$
C
P
U
_
D
1
3
$
C
P
U
_
D
1
4
$
C
P
U
_
D
1
5
$
C
P
U
_
D
[
0
.
.
6
3
]
2
MPB Schematic Diagrams B-3
Figure B-1 MPB CPU Board Logic Diagrams (Sheet 2 of 3)
B-4 MPB Schematic Diagrams
Figure B-1 MPB CPU Board Logic Diagrams (Sheet 3 of 3)
C22
SCD1U
C13
SCD1U
C29
SCD1U
C40
SCD1U
C25
SCD1U
CPU_VEND
CPU_ID2
CPU_ID3
1
1
1
1
2
R14
0R3
1
2
R2
0R3
1
2
R3
0R3
1
2
R12
0R3
1
2
R11
0R3
CPU_ID0
CPU_ID1
1
1
Not Installed
C36
SCD1U
C30
SCD1U
R12 R11 R12
SHIGA SHIGA
R2 R3
RATIO
1
2
R25
36KR3D
R11
SHIVA
CPU
CLOCK
CPU_VOLT0 1
FOR SHIGA
SHIVA NOT INS.
CPU_VOLT1
CPU_THM
CPU_THMG
1
1
1
THERMAL SENSOR
1
2
TH1
TH301
50MHz
60MHz
66MHz X
O : Install
O
X
X
X : Not install
X X
O
O
X
X X1.5
X2.0
X2.5
O O
X O
O X
X
O
C19
SCD1U
C43
SCD1U
C4
SCD1U
C2
SCD1U
VCC_CPU
C9
SCD1U
C21
SCD1U
C16
SCD1U
C12
SCD1U
C6
SCD1U
VCC_CPU
C17
SCD1U
C28
SCD1U
C41
SCD1U
C5
SCD1U
C23
SCD1U
C8
SCD1U
C24
SCD1U
C10
SCD1U
C11
SCD1U
C35
SCD1U
C39
SCD1U
C31
SCD1U
C42
SCD1U
C52
SCD1U
VCC_I/O
1
2
R26
10KR3
CPU_THM
C47
SCD1U
CPU_VEND
CPU_ID2
CPU_ID3
FOR SHIVA
SHIGA NOT INS.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
J2
HRS-CON18
1 2
R8
33R3
1 2
R9
33R3
1 2
R27
33R3 1 2
R22
33R3
$CPUINIT
$RS#
$PRDY
$TDI
$TDO
$TMS
$TCK
$TRST#
$CPURST
VCC_I/O
1
1
2
2
2
2
2
2
SHIVA & SHIGA NOT INS.
DQ
1
CLK/CONV#
2
RST#
3
GND
4
VDD
8
THIGH
7
TLOW
6
TCOM
5
U2
DS1620
CPU_VOLT0
CPU_VOLT1
CPU_THMG
MPB Schematic Diagrams B-5
Figure B-2 MPB Battery Board Logic Diagrams (Sheet 1 of 1)
CLOSE BATTRY CONN. PIN1
1
2
3
4
5
6
7
8
CN1
AMP-CON8
1
2
3
4
5
6
7
8
CN2
MOLEX-CON8
C1
SC1000P50V3MX
C2
SC1000P50V3MX
C3
SC1000P50V3MX
C4
SC1000P50V3MX
C5
SC1000P50V3MX
C6
SC1000P50V3MX
B-6 MPB Schematic Diagrams
Figure B-3 MPB Main Board (Motherboard) Logic Diagrams (Sheet 1 of 10)
1
2
3
4
5678
R
P
5
S
R
N
1
0
1
2
3
4
5678
R
P
6
S
R
N
1
0
1
2
3
4
5678
R
P
7
S
R
N
1
0
$
P
C
IC
L
K
0A
D
8
A
D
9
A
D
1
0
A
D
1
1
A
D
1
2
A
D
1
3
A
D
1
4
A
D
1
5
A
D
2
4
$
P
C
IC
L
K
0
2
,1
0
1
2
R
1
1
9
1
0
R
3
1 2 3 4
5
6
7
8
R
P
1
0
S
R
N
1
0
1234
5
6
7
8
R
P
1
S
R
N
1
0
1234
5
6
7
8
R
P
2
S
R
N
1
0
R
E
Q
#
1
P
A
R
IN
T
C
#
IN
T
B
#
P
E
R
R
#
A
D
0
A
D
1
A
D
2
A
D
3
A
D
4
A
D
5
R
E
Q
#
1
P
A
R
IN
T
C
#
IN
T
B
#
$
P
C
IC
L
K
1
T
P
6
7
T
P
6
8
T
P
6
9
T
P
6
6
T
P
2
8
T
P
1
4
1
T
P
6
0
T
P
5
3
T
P
5
4
T
P
5
5
T
P
6
1
T
P
5
6
T
P
6
5
T
P
1
7
1
T
P
1
4
6
T
P
1
4
5
T
P
1
4
8
T
P
1
4
7
T
P
1
5
1
T
P
1
5
0
T
P
1
4
9
T
P
1
6
1
T
P
1
7
3
T
P
1
6
6
1 2 3 4 5 6 7 8 91
0
1
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
2
0
2
1
2
2
2
3
2
4
2
5
2
6
2
7
2
8
2
9
3
0
3
1
3
2
3
3
3
4
3
5
3
6
3
7
3
8
3
9
4
0
4
1
4
2
4
3
4
4
4
5
4
6
4
7
4
8
4
9
5
0
5
1
5
2
5
3
5
4
5
5
5
6
5
7
5
8
5
9
6
0
6
1
6
2
6
3
6
4
6
5
6
6
6
7
6
8
6
9
7
0
7
1
7
2
7
3
7
4
7
5
7
6
7
7
7
8
7
9
8
0
8
1
8
2
8
3
8
4
8
5
8
6
8
7
8
8
8
9
9
0
9
1
9
2
9
3
9
4
9
5
9
6
9
7
9
8
9
9
1
0
0
1
0
1
1
0
2
1
0
3
1
0
4
1
0
5
1
0
6
1
0
7
1
0
8
1
0
9
1
1
0
1
1
1
1
1
2
1
1
3
1
1
4
1
1
5
1
1
6
1
1
7
1
1
8
1
1
9
1
2
0
C
N
2
J
A
E
-
C
O
N
N
1
2
0
B
$
P
C
IC
L
K
1
2
2
,8
,1
0
8
8
,1
0
2
,8
C
/B
E
#
[
0
..3
]
1234
5
6
7
8
R
P
4
S
R
N
1
0
1234
5
6
7
8
R
P
9
S
R
N
1
0
1 2 3 4
5
6
7
8
R
P
3
S
R
N
1
0
C
R
T
_
S
W
3
Y
[
0
..7
]
Z
V
_
P
C
L
K
Z
V
_
L
R
C
L
K
Z
V
_
M
C
L
K
A
D
6
A
D
7
A
D
1
6
A
D
1
7
A
D
1
8
A
D
1
9
A
D
2
0
A
D
2
1
A
D
2
2
A
D
2
3
Y
0
Y
1
Y
2
Y
3
Y
4
Y
5
Y
6
Y
7
Z
V
_
P
C
L
K
C
/B
E
#
0
C
/B
E
#
1
C
/B
E
#
2
C
/B
E
#
3
T
P
5
7
T
P
5
8
T
P
1
7
7
T
P
5
9
T
P
6
2
T
P
6
3
T
P
6
4
T
P
7
4
T
P
7
5
T
P
7
6
T
P
7
7
T
P
1
7
5
T
P
7
3
T
P
7
2
T
P
7
1
T
P
7
0
T
P
1
5
2
T
P
1
0
3
T
P
1
6
7
T
P
1
6
8
T
P
1
6
5
T
P
1
6
4
T
P
1
7
0
T
P
1
7
2
T
P
1
6
2
T
P
1
6
0
T
P
1
6
3
T
P
1
5
3
T
P
2
4
T
P
1
5
4
T
P
1
4
4
T
P
1
7
6
5
88
8
8
1
2
R
1
1
8
1
0
R
3
1
2
R
1
2
1
1
0
R
3
1
2
R
1
2
2
1
0
R
3
1
2
3
4
5678
R
P
8
S
R
N
1
0
D
D
C
_
C
L
K
C
R
T
_
S
W
1
C
R
T
_
S
W
2
U
V
[
0
..7
]
Z
V
_
S
C
L
K
Z
V
_
D
A
T
A
F
R
A
M
E
#
S
E
R
R
#
S
T
O
P
#
T
R
D
Y
#
IR
D
Y
#
Z
V
_
H
R
E
F
Z
V
_
V
R
E
F
A
D
2
5
A
D
2
6
A
D
2
7
A
D
2
8
A
D
2
9
A
D
3
0
A
D
3
1
Z
V
_
S
C
L
K
Z
V
_
D
A
T
A
U
V
0
U
V
1
U
V
2
U
V
3
U
V
4
U
V
5
U
V
6
U
V
7Z
V
_
H
R
E
F
Z
V
_
V
R
E
F
55
5
8
88
2
,8
,1
0
8
,1
0
2
,8
,1
0
2
,8
,1
0
2
,8
,1
0
88
1
2
R
1
2
0
0
R
3
1
2
R
1
2
3
0
R
3
T
2
4
8
T
P
-
1
T
5
5
T
P
-
1
T
1
9
1
T
P
-
1
T
7
0
T
P
-
1
T
1
7
7
T
P
-
1
T
1
7
6
T
P
-
1
T
6
3
T
P
-
1
T
4
6
T
P
-
1
T
1
9
3
T
P
-
1
T
5
6
T
P
-
1
T
6
4
T
P
-
1
T
1
7
3
T
P
-
1
T
1
6
6
T
P
-
1
T
1
7
5
T
P
-
1
T
5
7
T
P
-
1
T
1
5
T
P
-
1
T
1
1
4
T
P
-
1
T
5
8
T
P
-
1
T
1
5
2
T
P
-
1
T
1
6
7
T
P
-
1
T
1
6
8
T
P
-
1
T
7
4
T
P
-
1
T
5
9
T
P
-
1
T
1
8
1
T
P
-
1
T
P
2
4
8
T
P
4
6
T
P
1
9
3
T
P
1
5
T
P
1
1
4
T
P
1
8
1
T
P
5
9
T
P
5
8
T
P
5
7
T
P
5
6
T
P
5
5
T
P
6
3
T
P
6
4
T
P
1
7
5
T
P
1
5
2
T
P
7
4
T
P
1
6
8
T
P
1
6
7
T
P
1
6
6
T
P
1
7
3
T
P
1
7
6
T
P
1
7
7
T
P
1
9
1
T
P
7
0
T
1
8
2
T
P
-
1
T
7
3
T
P
-
1
T
7
5
T
P
-
1
T
1
6
5
T
P
-
1
T
1
6
4
T
P
-
1
T
7
6
T
P
-
1
T
7
2
T
P
-
1
T
1
3
7
T
P
-
1
T
8
8
T
P
-
1
T
7
1
T
P
-
1
T
7
7
T
P
-
1
T
1
7
0
T
P
-
1
T
1
7
2
T
P
-
1
T
1
0
3
T
P
-
1
T
6
2
T
P
-
1
T
1
3
8
T
P
-
1
T
P
1
8
2
T
P
1
3
7
T
P
8
8
T
P
1
3
8
T
P
6
2
T
P
7
1
T
P
7
2
T
P
7
3
T
P
7
5
T
P
7
6
T
P
7
7
T
P
1
0
3
T
P
1
7
2
T
P
1
7
0
T
P
1
6
4
T
P
1
6
5
C
R
T
_
V
S
C
R
T
_
H
S
L
O
O
P
B
A
C
K
5
,1
0
5
,1
0
C
R
T
_
B
C
R
T
_
G
C
R
T
_
R
R
G
B
_
G
N
D
R
G
B
_
G
N
D
5
,1
0
5
,1
0
5
,1
0
N
O
T
IN
S
T
A
L
L
12
R
1
4
3
1
0
K
R
3
12
R
1
8
4
7
K
R
3
F
R
A
M
E
#
P
C
IR
S
T
#
D
E
V
S
E
L
#
+
5
V
12
R
1
4
4
4
7
K
R
3
12
R
1
4
5
4
7
K
R
3
12
R
1
4
6
4
7
K
R
3
T
R
D
Y
#
IR
D
Y
#
|P
O
W
E
R
.S
C
H
|L
IN
K
|D
O
C
K
ID
E
.S
C
H
|F
E
A
T
U
R
E
.S
C
H
|D
O
C
K
P
O
R
T
.S
C
H
|C
H
A
R
G
E
R
.S
C
H
|C
D
_
F
D
D
.S
C
H
P
A
G
E
2
P
A
G
E
1
P
A
G
E
3
P
A
G
E
4
P
A
G
E
5
P
A
G
E
6
P
A
G
E
7
|P
S
2
_
C
O
N
N
.S
C
H
P
A
G
E
8
P
A
G
E
9
|A
U
D
IO
.S
C
H
P
A
G
E
1
0
|T
P
.S
C
H
D
o
c
k
in
g
c
o
n
n
.
U
M
A
ID
E
I/F
(
P
C
I0
6
4
3
Q
)
F
e
a
t
u
r
e
b
o
a
r
d
c
o
n
n
.
C
D
,H
D
D
&
F
D
D
I/F
&
Q
W
C
R
T
,P
R
IN
T
E
R
,R
S
-
2
3
2
C
O
N
N
.
C
H
R
G
E
R
,E
2
P
R
O
M
&
B
A
T
T
R
Y
C
O
N
N
.
A
U
D
IO
A
M
P
. &
D
C
_
IN
B
D
. C
O
N
N
.
D
C
/D
C
,F
D
D
/ID
E
'S
P
W
O
E
R
M
O
S
F
E
T
&
1
4
9
3
'S
P
O
W
E
R
M
O
S
F
E
T
P
S
2
'S
M
O
U
S
E
, P
S
2
'S
K
E
Y
B
O
A
R
D
&
U
S
B
C
O
N
N
.
D
O
C
K
I
N
G
C
O
N
N
E
C
T
O
R
A
D
[
0
..3
1
]
A
D
[
0
..3
1
]
2
,8
,1
0
T
6
7
T
P
-
1
T
6
8
T
P
-
1
T
6
1
T
P
-
1
T
1
6
1
T
P
-
1
T
1
4
9
T
P
-
1
T
1
5
0
T
P
-
1
T
2
6
2
T
P
-
1
T
P
1
6
1
T
P
1
4
9
T
P
1
5
0
T
P
6
7
T
P
6
8
T
P
6
1
L
O
O
P
B
A
C
K
T
P
3
7
5
T
3
7
5
T
P
-
1
T
1
6
3
T
P
-
1
T
1
5
1
T
P
-
1
T
1
7
1
T
P
-
1
T
6
0
T
P
-
1
T
5
4
T
P
-
1
T
1
6
0
T
P
-
1
T
1
4
7
T
P
-
1
T
6
5
T
P
-
1
T
2
8
T
P
-
1
T
5
3
T
P
-
1
T
6
6
T
P
-
1
T
1
4
8
T
P
-
1
T
1
4
4
T
P
-
1
T
2
4
T
P
-
1
T
1
4
1
T
P
-
1
T
1
4
5
T
P
-
1
T
1
6
2
T
P
-
1
T
1
5
4
T
P
-
1
T
1
4
6
T
P
-
1
T
1
5
3
T
P
-
1
T
P
1
6
3
T
P
1
6
0
T
P
1
4
4
T
P
2
4
T
P
1
6
2
T
P
1
5
4
T
P
1
5
3
T
P
1
4
6
T
P
1
4
5
T
P
1
4
1
T
P
1
4
8
T
P
1
4
7
T
P
1
5
1
T
P
1
7
1
T
P
6
5
T
P
6
6
T
P
5
3
T
P
2
8
T
P
6
0
T
P
5
4
D
C
B
A
T
O
U
T
T
6
9
T
P
-
1
T
P
6
9
T
3
7
6
T
P
-
1
T
P
3
7
6
1 2 3 4 5 6 7 8 91
0
1
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
2
0
2
1
2
2
2
3
2
4
2
5
2
6
2
7
2
8
2
9
3
0
3
1
3
2
3
3
3
4
3
5
3
6
3
7
3
8
3
9
4
0
4
1
4
2
4
3
4
4
4
5
4
6
4
7
4
8
4
9
5
0
5
1
5
2
5
3
5
4
5
5
5
6
5
7
5
8
5
9
6
0
6
1
6
2
6
3
6
4
6
5
6
6
6
7
6
8
6
9
7
0
7
1
7
2
7
3
7
4
7
5
7
6
7
7
7
8
7
9
8
0
8
1
8
2
8
3
8
4
8
5
8
6
8
7
8
8
8
9
9
0
9
1
9
2
9
3
9
4
9
5
9
6
9
7
9
8
9
9
1
0
0
1
0
1
1
0
2
1
0
3
1
0
4
1
0
5
1
0
6
1
0
7
1
0
8
1
0
9
1
1
0
1
1
1
1
1
2
1
1
3
1
1
4
1
1
5
1
1
6
1
1
7
1
1
8
1
1
9
1
2
0
C
N
1
J
A
E
-
C
O
N
N
1
2
0
B
S
B
1
2
R
2
0
R
3
1
2
R
1
5
3
3
K
3
R
3
A
U
D
IO
_
C
D
_
L
A
U
D
IO
_
C
D
_
R
E
N
_
1
3
9
4
P
W
R
C
S
I
C
S
O D
K
_
M
IC
D
K
_
M
O
S
O
N
H
D
S
E
L
W
G
A
T
E
#
D
S
K
C
H
G
#
R
D
A
T
A
#
T
R
K
0
#
W
R
T
P
R
T
#
F
B
A
C
T
#
C
D
/F
D
D
_
R
D
Y
#
C
D
_
L
O
C
K
#
S
M
B
_
C
L
K
S
M
B
_
D
A
T
A
I2
C
_
C
L
K
I2
C
_
D
A
T
A
E
N
_
F
B
Z
V
#
L
O
O
P
B
A
C
K
T
P
2
4
8
T
P
4
6
A
U
D
_
G
N
D
3
3
6
,1
0
7
,1
0
7
4
7
3
,1
0
3
,1
0
33
3
3
8
,1
0
6
6
7
7
7
,8
,1
0
7
,1
0
8
,1
0
T
P
3
7
5
L
O
O
P
B
A
C
K
1
2
R
5
0
R
3
D
K
_
L
IN
E
IN
_
L
D
K
_
L
IN
E
IN
_
R
P
R
I1
#
P
D
T
R
1
#
P
C
T
S
1
#
P
S
O
U
T
1
P
R
T
S
1
#
P
S
IN
1
P
D
S
R
1
#
D
K
_
B
L
1
#
D
K
_
B
L
2
#
F
B
D
A
T
A
C
D
_
E
X
IS
T
#
D
K
_
C
H
G
_
L
E
D
D
K
_
P
J
IN
#
D
K
_
S
O
U
N
D
_
R
D
K
_
S
O
U
N
D
_
L
F
D
D
_
E
X
IS
T
#
E
N
_
C
H
G
R
_
R
O
M
F
L
A
S
H
_
O
N
D
K
_
H
D
L
E
D
#
O
N
/O
F
F
#
D
O
C
K
P
W
O
K
7
7
N
O
C
O
N
D
K
_
M
IC
_
P
J
IN
T
P
1
9
1
A
U
D
_
G
N
D
A
D
+
44
5555555 778
,1
0
37
4
4
,1
0
4
,1
0
3
7
,1
0
8
,1
0
3
6
6
2
,8
,1
0
5
4
1
2
3
4
5 6 7 8
R
P
1
1
S
R
N
1
0
P
S
2
C
L
K
P
S
2
D
A
T
A
S
T
R
O
B
# A
C
K
#
B
U
S
Y
P
E
S
L
C
T
S
L
C
T
IN
#
IN
IT
#
E
R
R
O
R
#
A
U
T
O
F
D
#
U
S
B
P
0
U
S
B
P
1
P
D
C
D
1
#
IR
Q
1
5
G
N
T
#
1
G
N
T
#
0
R
E
Q
#
0
P
C
IR
S
T
#
T
P
1
8
1
T
P
1
3
7
T
P
8
8
T
P
1
3
8
9
,1
0
9
,1
0
5 5 5 5 5 5 5 5 5
9
,1
0
9
,1
0
52
2
,1
0
8
,1
0
8
2
,8
,1
0
T
P
3
7
6
T
P
1
8
2
12
R
1
2
4
1
0
R
3
1
2
R
1
0
R
3
1
2
R
3
0
R
3
K
B
C
L
K
K
B
D
A
T
A
P
D
0
P
D
1
P
D
2
P
D
3
P
D
4
P
D
5
P
D
6
P
D
7
F
D
D
/P
R
T
#
S
T
E
P
#
F
D
IR
W
D
A
T
A
#
M
T
R
0
#
D
R
0
#
IN
D
E
X
#
D
E
V
S
E
L
#
C
H
A
R
G
E
R
_
O
N
T
P
1
9
3
T
P
1
5
9
,1
0
9
,1
0
5
3
,1
03
,1
0
3
,1
03
,1
03
,1
0
3
2
,8
,1
0
7
,1
0
1
,5
1
,5
1
,5
1
,5
1
,5
1
,5
1
,5
1
,5
T
P
1
1
4
MPB Schematic Diagrams B-7
Figure B-3 MPB Main Board (Motherboard) Logic Diagrams (Sheet 2 of 10)
1
2
R
2
1
2
2
R
3
1
2
R
3
9
D
U
M
M
Y
-
R
3
G
N
T
#
1
I
D
E
_
D
A
C
K
0
#
I
N
T
C
#
I
D
E
_
D
A
C
K
0
#
G
N
T
#
1
T
P
1
1
0
1 8
3
,1
0
3
4
147
U
1
1
B
S
S
H
C
1
4
1
2
R
1
5
8
D
U
M
M
Y
-
R
3
IR
Q
1
5
+
5
V
T
P
3
7
7
D
1
2
C
L
K
1
1
Q
9
Q
8
V
C
C
1
4
PR
10
G
N
D
7
CL
13
U
5
B
S
O
H
C
T
7
4
12
R
1
6
3
4
7
K
R
3
C
D
_
P
A
S
S
#
+
5
V
+
5
V
+
5
V
T
P
3
7
8
N
C
1
/1
O
E
2
1
A
3
1
Y
4
/2
O
E
5
2
A
6
G
N
D
8
2
Y
7
N
C
9
3
Y
1
0
3
A
1
1
/3
O
E
1
2
4
Y
1
3
4
A
1
4
/4
O
E
1
5
V
C
C
1
6
U
2
4
Q
S
3
1
2
5
F
R
A
M
E
#
P
C
I
R
S
T
#
F
R
A
M
E
#
+
5
V
1
T
P
3
8
0
1
2
R
1
9
2
0
K
R
3
C
3
S
C
D
1
U
C
4
S
C
1
K
P
I
R
D
Y
#
S
T
O
P
#
P
A
R
P
E
R
R
#
D
E
V
S
E
L
#
T
R
D
Y
#
I
D
E
_
D
R
Q
0
$
P
C
I
C
L
K
0
A
D
2
4
I
R
D
Y
#
S
T
O
P
#
P
A
R
P
E
R
R
#
D
E
V
S
E
L
#
T
R
D
Y
#
I
D
E
_
D
R
Q
0
P
C
I
R
S
T
#
$
P
C
I
C
L
K
0
T
P
1
1
2
TP267
TP334
+
3
.3
V
1
,8
,
1
0
1
,
8
,
1
0
1
,
8
,
1
0
1
,
8
,
1
0 1
,
8
,
1
0
1
1
,
8
,
1
0
3
12
R
3
3
1
0
K
R
3
1
2
R
2
0
2
2
R
3
R
E
S
E
T
#
1
P
C
I
M
O
D
E
2
C
/
B
E
3
#
3
C
/
B
E
2
#
4
C
/
B
E
1
#
5
C
/
B
E
0
#
6
A
D
3
1
7
A
D
3
0
8
A
D
2
9
9
A
D
2
8
1
0
A
D
2
7
1
1
A
D
2
6
1
2
A
D
2
5
1
3
A
D
2
4
1
4
V
S
S
1
5
V
D
D
1
6
A
D
2
3
1
7
A
D
2
2
1
8
A
D
2
1
1
9
A
D
2
0
2
0
E
N
I
D
E
2
1
I
R
Q
1
4
2
2
A
D
1
9
2
3
A
D
1
8
2
4
A
D
1
7
2
5
AD16
26
VSS
27
AD15
28
AD14
29
AD13
30
AD12
31
AD11
32
AD10
33
AD9
34 AD
8
35
DSD15
36
DSD14
37
DSD13
38
DSD12
39
VSS
40
VDD
41
AD7
42
AD6
43 AD5
44
AD4
45 AD
3
46
AD2
47
AD1
48
AD0
49
DSD11
50 D
S
D
1
0
5
1
D
S
D
9
5
2
D
S
D
8
5
3
V
S
S
5
4
D
C
S
0
#
5
5
D
C
S
1
#
5
6
D
I
O
R
#
5
7
D
I
O
W
#
5
8
D
R
S
T
#
5
9
D
M
A
R
Q
1
6
0
T
E
S
T
1
#
6
1
D
S
D
7
6
2
D
S
D
6
6
3
D
S
D
5
6
4
D
S
D
4
6
5
V
S
S
6
6
V
D
D
6
7
D
S
A
0
6
8
D
S
A
1
6
9
D
S
A
2
7
0
D
S
D
3
7
1
D
S
D
2
7
2
D
S
D
1
7
3
D
S
D
0
7
4
D
I
R
Q
1
7
5
DCHRDY
76
2NDIOR#
77
2NDIOW#
78
DCS3#
79
DCS
2#
80
PCIREQ#
81
PCIGNT#
82
IRQ15
83
INTA#
84
TEST0
85
DIRQ2
86
2NDIDEEN#/DMACK0#
87
DMACK1#
88
PCICLK
89
VSS
90
VDD
91
TRDY#
92
DEVSEL#
93
DMARQ0
94
PERR#
95
PAR
96
STOP#
97
FRAME#
98
IRDY#
99
IDSEL
100
U
4
P
C
I
0
6
4
3
Q
1
2
3
4
5 6 7 8
R
P
1
8
S
R
N
2
2
C
1
S
C
D
1
U
C
2
S
C
1
K
P
1
2
R
2
3
2
2
R
3
R
E
Q
#
1
I
D
E
_
R
D
Y
R
E
Q
#
1
T
P
3
5
1
T
P
2
9
3
+
3
.3
V
1
,1
0
3
12
R
2
4
1
K
R
3
+
5
V
S
C
12
R
X
6
1
0
K
R
3
S
B
1
2
R
2
2
2
2
R
3
12
R
3
7
4
K
7
R
3
1
2
R
3
8
0
R
3
IR
Q
1
5
I
D
E
_
I
R
Q
T
P
2
6
9
1
,
1
0
3
N
O
T
I
N
S
T
A
L
L
1
2
3
4
5 6 7 8
R
P
2
1
S
R
N
2
2
C
6
S
C
4
7
0
P
ID
E
_
A
0
ID
E
_
A
1
ID
E
_
A
2
I
D
E
_
I
O
W
#
I
D
E
_
I
O
R
#
I
D
E
_
C
S
0
#
I
D
E
_
C
S
1
#
I
D
E
_
R
S
T
#
I
D
E
_
A
0
I
D
E
_
A
1
I
D
E
_
A
2
I
D
E
_
R
S
T
#
3
,
1
0
3
,
1
0
3
,
1
0
3
,
1
0
3
,
1
0
3
,
1
0
3
,
1
0
3
,
1
0
1
2
3
4
5 6 7 8
R
P
1
9
S
R
N
2
2
1
2
3
4
5 6 7 8
R
P
2
0
S
R
N
2
2
1
2
3
4
5 6 7 8
R
P
2
2
S
R
N
2
2
12
R
3
1
2
K
2
R
3
ID
E
_
D
0
ID
E
_
D
1
ID
E
_
D
2
ID
E
_
D
3
I
D
E
_
D
4
I
D
E
_
D
5
I
D
E
_
D
6
I
D
E
_
D
7
I
D
E
_
D
8
I
D
E
_
D
9
I
D
E
_
D
1
0
I
D
E
_
D
1
1
T
P
3
1
0
T
P
3
5
4
T
P
3
5
3
T
P
3
2
0
T
P
3
2
1
T
P
3
4
3
T
P
3
2
2T
P
3
3
9
T
P
3
2
6
T
P
3
4
0
T
P
3
2
5
T
P
3
3
8
T
P
3
0
0
T
P
2
9
7
T
P
2
9
8
T
P
2
9
9
T
P
3
1
4
T
P
3
1
3
T
P
3
1
2
T
P
3
1
1
T
P
2
0
12
R
3
6
1
0
K
R
3
12
R
3
2
2
K
2
R
3
A
D
1
7
A
D
1
8
A
D
1
9
A
D
2
0
A
D
2
1
A
D
2
2
A
D
2
3
A
D
2
4
A
D
2
5
A
D
2
6
A
D
2
7
A
D
2
8
A
D
2
9
A
D
3
0
A
D
3
1
C
/B
E
#
0
C
/B
E
#
1
C
/B
E
#
2
C
/B
E
#
3
T
P
3
1
9
T
P
2
9
+
3
.
3
V
P
C
I
0
6
4
3
C
/B
E
#
[
0
..
3
]
C
/B
E
#
[
0
.
.
3
]
I
D
E
_
D
0
I
D
E
_
D
1
I
D
E
_
D
2
I
D
E
_
D
3
I
D
E
_
D
4
I
D
E
_
D
5
I
D
E
_
D
6
I
D
E
_
D
7
I
D
E
_
D
8
I
D
E
_
D
9
I
D
E
_
D
1
0
1
,
8
,
1
0
A
D
[
0
.
.
3
1
]
[
0
.
.1
5
]
A
D
[
0
.
.
3
1
]
I
D
E
_
D
1
1
I
D
E
_
D
1
2
I
D
E
_
D
1
3
I
D
E
_
D
1
4
I
D
E
_
D
1
5
I
D
E
_
D
[
0
.
.
1
5
]
1
,
8
,
1
0
I
D
E
C
O
N
T
R
O
L
L
E
R
1
2
3
4 5
6
7
8
R
P
1
7
S
R
N
2
2
AD8
AD9
AD10
AD11
AD12
AD13
AD
14
AD15
AD16
IDE_D12
IDE_D13
IDE_D14
IDE_D15
TP349
TP348
TP347
TP346
C
5
S
C
4
7
P
1
2
R
3
4
3
3
R
3
12
R
3
5
1
K
R
3
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
I
D
E
_
I
O
C
S
1
6
#
+
3
.
3
V
ID
E
_
I
O
C
S
1
6
#
3
+
3
.3
V
T
3
1
0
T
P
-
1
T
3
5
4
T
P
-
1
T
3
5
3
T
P
-
1
T
3
2
0
T
P
-
1
T
3
2
1
T
P
-
1
T
3
4
3
T
P
-
1
T
3
2
2
T
P
-
1
T
2
9
7
T
P
-
1
T
3
4
6
T
P
-
1
T
3
4
7
T
P
-
1
T
3
0
0
T
P
-
1
T
3
3
8
T
P
-
1
T
3
2
5
T
P
-
1
T
3
4
0
T
P
-
1
T
3
2
6
T
P
-
1
T
3
3
9
T
P
-
1
T
3
1
3
T
P
-
1
T
3
1
2
T
P
-
1
T
3
1
1
T
P
-
1
T
3
4
9
T
P
-
1
T
3
4
8
T
P
-
1
T
P
3
2
2
T
P
3
4
3
T
P
3
2
1
T
P
3
2
0
T
P
3
5
3
T
P
3
5
4
T
P
3
1
0
T
P
3
3
9
T
P
3
2
6
T
P
3
4
0
T
P
3
2
5
T
P
3
3
8
T
P
3
0
0
T
P
2
9
7
T
P
3
4
6
T
P
3
4
7
T
P
3
4
8
T
P
3
4
9
T
P
3
1
1
T
P
3
1
2
T
P
3
1
3
T
3
5
1
T
P
-
1
T
2
6
9
T
P
-
1
T
2
9
8
T
P
-
1
T
2
9
9
T
P
-
1
T
3
1
4
T
P
-
1
T
P
3
5
1
T
P
2
6
9
T
P
2
9
8
T
P
2
9
9
T
P
3
1
4
T
2
0
T
P
-
1
T
P
2
0
T
P
3
2
3
T
3
2
3
T
P
-
1
T
P
3
7
8
T
P
3
8
0
T
3
7
8
T
P
-
1
T
3
8
0
T
P
-
1
T
P
3
7
7
T
3
7
7
T
P
-
1
T
P
3
6
1
T
P
3
0
4
T
P
3
5
7
T
P
3
4
4
T
2
9
3
T
P
-
1
T
1
1
0
T
P
-
1
T
3
3
4
T
P
-
1
T
1
1
2
T
P
-
1
T
2
6
7
T
P
-
1
T
2
9
T
P
-
1
T
3
1
9
T
P
-
1
T
3
6
1
T
P
-
1
T
3
0
4
T
P
-
1
T
3
5
7
T
P
-
1
T
3
4
4
T
P
-
1
T
P
3
1
9
T
P
2
9
T
P
2
6
7
T
P
1
1
2
T
P
3
3
4
T
P
1
1
0
T
P
2
9
3
12
R
4
0
4
7
R
3
C
1
1
S
C
3
9
P
T
R
D
Y
#
T
P
3
4
4
12
R
4
1
4
7
R
3
C
1
0
S
C
3
9
P
IR
D
Y
#
T
P
3
5
7
N
o
t
i
n
s
t
a
l
l
12
R
4
2
4
7
R
3
C
9
S
C
3
9
P
$
P
C
I
C
L
K
0
T
P
3
2
3
12
R
4
4
4
7
R
3
C
8
S
C
3
9
P
D
E
V
S
E
L
#
T
P
3
0
4
12
R
4
3
4
7
R
3
C
7
S
C
3
9
P
F
R
A
M
E
#
T
P
3
6
1
B-8 MPB Schematic Diagrams
Figure B-3 MPB Main Board (Motherboard) Logic Diagrams (Sheet 3 of 10)
MPB Schematic Diagrams B-9
Figure B-3 MPB Main Board (Motherboard) Logic Diagrams (Sheet 4 of 10)
AUDIO AMP.
C88
SCD1U
C89
SC1KP
AD+
1 2
L7
SCHOKE-D
+5V AMP_5V
C85
SC100P
1 2
R100
56KR3
+5V
+5V
1
2
R102
DUMMY-R3 1
2
R101
100KR3
C87
SCD1U
+5V
SB
1
2
3
Q7
2N7002
2
4
6
8
10
12
14
16
18
20
3
5
7
9
11
13
15
17
19
1
CN13
HRS-CONN20D
1
3
D14
BZX84C4V3L
1 2
R159
1KR6
1 2
R162
1KR6
DK_LINEIN_R
DK_LINEIN_L
DK_PJIN#
DK_MIC_PJIN
LINE_OUT_L
LINE_OUT_R
DK_PJIN#
AD+
AUD_GND
1
1
1,10
1
1 2
C82
ST47U10VDM
1 2
C83
ST47U10VDM
1 2
R99
56KR3
DK_MIC
LINE_OUT_L
LINE_OUT_R TP333
TP328
AMP_5V
AUD_GND
1
IN_A
2
IN_B
6
BYPASS
3
SHUTDOWN
5
OUT_A
1
OUT_B
7
V
D
D
8
G
N
D
4
U19
LM4880M
1 2
R97
20KR3
1 2
R98
20KR3
C81
SC1U
C84
SCD1U
DK_SOUND_L
DK_SOUND_R
DK_PJIN#
TP329
TP332
TP330
AUD_GND
AUD_GND
1
1
C86
SC100P
MPB DC_IN B.D CONN.
T329
TP-1
TP329
T332
TP-1
T330
TP-1
T333
TP-1
T328
TP-1
TP332
TP330
TP333
TP328
B-10 MPB Schematic Diagrams
Figure B-3 MPB Main Board (Motherboard) Logic Diagrams (Sheet 5 of 10)
MPB Schematic Diagrams B-11
Figure B-3 MPB Main Board (Motherboard) Logic Diagrams (Sheet 6 of 10)
C
6
1
S
C
1
K
P
12
C
6
7
S
T
1
0
0
U
1
6
V
D
M
1
2
R
1
1
1
1
0
K
R
3
1
2
R
1
1
2
1
0
K
R
3
3
V
1
3
V
2
5
V
3
5
V
4
3
V
_
I
D
7
D
C
B
A
T
T
_
I
N
8
D
C
B
A
T
T
_
I
N
9
3
.
3
V
O
N
/
O
F
F
1
0
P
G
V
C
C
1
1
P
G
1
2
O
N
/
O
F
F
1
3
5
V
S
B
1
4
1
2
V
1
5
8
V
1
6
G
N
D
5
G
N
D
6
C
N
1
4
T
6
2
-
0
3
0
-
C
+
5
V
+
1
2
V
+
8
V
12
C
5
8
S
T
1
0
0
U
1
6
V
D
M
12
C
5
9
S
T
1
0
0
U
1
6
V
D
M
C
6
4
S
C
D
1
U
12
C
6
5
S
T
2
2
U
3
5
V
D
M
1
2
C
6
6
S
T
2
2
U
3
5
V
D
M
C
6
8
S
C
1
K
P
C
6
9
S
C
D
1
U
1
2
R
1
4
1
1
0
0
K
R
3
O
N
/
O
F
F
#
D
C
B
A
T
O
U
T
+
3
.
3
V
+
5
V
1
1 3
D
1
3
B
Z
X
8
4
C
4
V
3
L
1
2
R
1
5
7
3
K
3
R
3
D
O
C
K
P
W
O
K
T
P
3
6
0
+
5
V
1
,
1
0
1
2
147
U
1
1
A
S
S
H
C
1
4
D
C
/
D
C
&
P
O
W
E
R
S
W
I
T
C
H
T
P
3
4
1
+
5
V
9
8
147
U
1
1
D
S
S
H
C
1
4
D
C
/
D
C
8
1
2
D
6
M
B
R
S
3
4
0
1
3
9
4
P
O
W
E
R
T
P
2
5
7
1
2
3
4
8
7
6
5
U
1
6
S
I
4
4
1
0
D
Y
C
D
_
5
V
+
5
V
1
2 3
Q
2
2
N
7
0
0
2
12
R
8
1
1
0
0
K
R
3
12
R
5
8
1
K
R
3
12
R
1
4
8
2
2
0
K
R
3
TP241
T
P
2
8
2
C
D
_
5
V
+
1
2
V
C
D
/
F
D
D
_
R
D
Y
#
C
D
/
F
D
D
_
R
D
Y
#
1
,
3
,
1
0
1
2
R
5
6
1
0
0
K
R
3
C
2
2
S
C
D
1
U
1
2
D
1
S
1
N
4
1
4
8
31
2
Q
1
R
N
1
4
2
4
1
3
1
2
147
U
3
F
S
S
H
C
1
4
1
2
3
1
4
7
U
1
2
A
S
S
H
C
3
2
C
D
_
L
O
C
K
#
C
D
_
L
O
C
K
#
T
P
8
3
T
P
2
9
6
T
P
3
4
5
+
5
V
+
5
V
+
5
V
1
,
1
0
1
1
1
0
147
U
3
E
S
S
H
C
1
4
2
1
3
S
W
1
D
S
-
1
2
0
0
-
0
2
12
R
1
1
5
1
0
0
K
R
3
1
2
R
1
2
7
1
0
K
R
3
1
2
147
U
3
A
S
S
H
C
1
4
1
2
R
5
9
2
M
R
5
1
2
D
2
S
1
N
4
1
4
8
T
P
3
0
8
C
D
_
5
V
+
5
V
+
5
V
C
2
3
S
C
1
U
C
9
6
S
C
D
1
U
C
9
7
S
C
D
1
U
C
9
8
S
C
D
1
U
C
9
9
S
C
D
1
U
C
1
0
0
S
C
D
1
U
+
5
V
B
A
T
+
C
1
0
1
S
C
D
1
U
C
1
0
2
S
C
D
1
U
C
1
0
3
S
C
D
1
U
C
1
0
4
S
C
D
1
U
C
1
0
5
S
C
D
1
U
C
1
0
7
S
C
D
1
U
C
1
0
8
S
C
D
1
U
C
1
0
9
S
C
D
1
U
C
1
1
0
S
C
D
1
U
D
C
B
A
T
O
U
TC
1
0
6
S
C
D
1
U
C
1
1
1
S
C
D
1
U
C
1
1
2
S
C
D
1
U
+
1
2
V
T
2
4
9
T
P
-
1
T
2
5
7
T
P
-
1
T
3
1
8
T
P
-
1
T
3
5
9
T
P
-
1
T
2
8
2
T
P
-
1
T
3
4
1
T
P
-
1
T
3
6
0
T
P
-
1
T
3
0
5
T
P
-
1
T
2
4
1
T
P
-
1
T
8
3
T
P
-
1
T
3
0
8
T
P
-
1
T
3
4
5
T
P
-
1
T
P
2
4
9
T
P
2
5
7
T
P
3
1
8
T
P
3
5
9
T
P
2
8
2
T
P
3
4
1
T
P
3
6
0
T
P
3
0
5
T
P
2
4
1
T
P
8
3
T
P
3
0
8
T
P
3
4
5
T
2
9
6
T
P
-
1
T
P
2
9
6
C
7
0
S
C
D
1
U
12
C
7
1
S
T
1
0
U
3
5
V
D
M
T
P
2
4
9
1
2
F
1
S
M
D
0
7
5
3
0
V
/
0
.
7
5
A
1
2
3
4
8
7
6
5
U
1
5
S
I
4
4
3
5
D
Y
12
R
1
4
9
8
2
K
R
3
TP318
D
C
B
A
T
O
U
T
S
C
C
X
1
S
C
D
4
7
U
12
R
7
9
4
7
0
K
R
3
1
2 3
Q
3
2
N
7
0
0
2
12
R
1
5
0
4
7
0
K
R
3
1
2
R
1
4
0
1
0
0
K
R
3
T
P
3
0
5
TP359
1
2
3
D
1
2
B
A
V
9
9
E
N
_
1
3
9
4
P
W
R
D
C
B
A
T
O
U
T
1
B-12 MPB Schematic Diagrams
Figure B-3 MPB Main Board (Motherboard) Logic Diagrams (Sheet 7 of 10)
1
2 3
Q
4
2
N
7
0
0
2
C
1
1
3
S
C
D
1
U
A
D
5
V
T
P
2
9
2
+
5
V
S
B
12
R
8
8
1
5
0
K
R
3
12
R
8
7
4
7
K
R
3
A
D
+
T
2
9
2
T
P
-
1
T
3
3
6
T
P
-
1
T
3
3
5
T
P
-
1
T
3
3
7
T
P
-
1
T
2
8
5
T
P
-
1
T
2
4
4
T
P
-
1
T
1
2
1
T
P
-
1
T
P
2
9
2
T
P
3
3
6
T
P
3
3
5
T
P
3
3
7
T
P
2
8
5
T
P
2
4
4
T
3
5
0
T
P
-
1
T
3
2
7
T
P
-
1
T
3
6
7
T
P
-
1
T
3
6
3
T
P
-
1
T
3
6
4
T
P
-
1
T
3
7
2
T
P
-
1
T
P
1
2
1
T
P
3
5
0
T
P
3
2
7
D
K
_
B
L
3
#
I
D
_
C
L
K
I
D
_
D
A
T
A
A
D
5
V
D
K
_
M
O
S
O
N
D
C
B
A
T
O
U
T
1
,
1
0
1
2
R
1
0
4
5
6
0
R
3
1
2
3
D
7
B
A
V
9
9
T
P
3
5
0
D
K
_
B
L
3
#
1
2 3
Q
X
1
2
N
7
0
0
2
S
C
C
7
5
S
C
D
1
U
C
7
6
S
C
1
K
P
B
A
T
+
+
5
V
S
B
1
2
3
4
5
6
7
8
C
N
1
0
M
O
L
E
X
-
C
O
N
8
C
7
3
S
C
D
1
U
1
2
C
7
2
S
T
2
2
U
3
5
V
D
M
C
7
4
S
C
1
K
P
S
M
B
_
C
L
K
S
M
B
_
D
A
T
A
B
A
T
_
T
H
B
A
T
_
V
S
B
A
T
+
1
1
1
2
3
4
8
7
6
5
U
1
8
S
I
4
4
3
5
D
Y
12
R
8
6
3
3
0
K
R
3
T
P
1
2
1
B
A
T
+
12
R
8
5
8
2
K
R
3
1 2
D
X
1
M
M
B
Z
5
2
3
0
B
2 1
D
X
2
M
B
R
0
5
4
0
T
1
1
2 3
Q
X
3
2
N
7
0
0
2
C
X
4
S
C
D
1
U
5
0
V
3
Z
Y
2
1
D
9
N
S
Q
0
3
A
0
4
-
1
2
1
D
8
N
S
Q
0
3
A
0
4
-
1
T
P
2
4
4
D
C
B
A
T
O
U
T
A
D
+
4
3
147
5
U
2
2
C
S
O
H
C
4
0
6
6
+
5
V
S
B
+
5
V
S
B
D
K
_
B
L
3
#
L
O
O
P
B
A
C
K
12
R
X
1
1
0
0
K
R
3
+
5
V
S
B
C
X
3
S
C
D
1
U
1
2
3
D
X
3
B
A
V
9
9
1
2
R
X
3
1
K
R
3
S
C
E
N
_
C
H
G
R
_
R
O
M
I
2
C
_
C
L
K
I
2
C
_
D
A
T
A
1
1
,
8
,
1
01
,
1
0
1
2
147
13
U
2
2
A
S
O
H
C
4
0
6
6
1
1
1
0
147
12
U
2
2
B
S
O
H
C
4
0
6
6
I
D
_
C
L
K
I
D
_
D
A
T
A
+
5
V
S
B
+
5
V
S
B
12
R
1
4
2
1
0
0
K
R
3
12
R
9
1
1
M
R
3
D
K
_
B
L
3
#
T
P
3
2
7
+
5
V
12
R
1
0
6
0
R
3
12
R
1
0
7
0
R
3
12
R
1
0
8
D
U
M
M
Y
-
R
3
+
5
V
T
P
3
3
6
T
P
3
3
5
T
P
3
3
7
12
R
1
0
9
D
U
M
M
Y
-
R
3
12
R
1
0
5
0
R
3
12
R
1
1
0
D
U
M
M
Y
-
R
3
A
0
1
A
2
3
V
C
C
8
S
C
L
6
A
1
2
G
N
D
4
S
D
A
5
T
E
S
T
7
U
2
0
S
2
5
6
K
8
12
R
1
1
3
0
R
3
I
2
C
_
C
L
K
I
2
C
_
D
A
T
A
TP285
2
4
C
0
2
1
2 3
Q
5
2
N
7
0
0
2
M
A
S
T
E
R
/
S
L
A
V
E
S
E
L
E
C
T
I
N
M
A
S
T
E
R
M
O
D
E
P
U
L
L
L
O
W
1
1
2
R
X
4
2
2
0
K
R
3
C
X
6
S
C
D
1
U
5
0
V
3
Z
Y
1
2
R
X
2
2
K
2
R
3
S
C
1 2 3 4 5 6 7 8 9
1
0
1
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
2
0
C
N
9
M
O
L
E
X
-
C
O
N
N
2
0
C
S
O
C
S
I
D
K
_
C
H
G
_
L
E
D
S
M
B
_
C
L
K
S
M
B
_
D
A
T
A
I
D
_
D
A
T
A
I
D
_
C
L
K
B
A
T
_
T
H
B
A
T
_
V
S B
A
T
+
B
A
T
+
1
,
1
0
1
,
1
0
12
R
8
3
1
0
0
K
R
3
1 2 3 4 5 6 7 8 9
1
0
1
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
2
0
C
N
8
M
O
L
E
X
-
C
O
N
N
2
0
D
K
_
B
L
1
#
D
K
_
B
L
2
#
C
H
A
R
G
E
R
_
O
N
D
K
_
B
L
3
#
A
D
5
V
D
C
B
A
T
O
U
T
D
C
B
A
T
O
U
T
A
D
+
+
5
V
S
B
+
5
V
1
,
1
0
C
H
A
R
G
E
R
I
/
F
MPB Schematic Diagrams B-13
Figure B-3 MPB Main Board (Motherboard) Logic Diagrams (Sheet 8 of 10)
12
R
4
7
4
7
R
3
12
R
4
8
4
7
R
3
12
R
4
9
4
7
R
3
C
1
2
S
C
3
9
P
C
1
3
S
C
3
9
P
C
1
4
S
C
3
9
P
F
R
A
M
E
#
D
E
V
S
E
L
#
$
P
C
I
C
L
K
1
T
P
3
5
5
T
P
3
5
6
T
P
3
0
9
12
R
4
5
4
7
R
3
12
R
4
6
4
7
R
3
C
1
5
S
C
3
9
P
C
1
6
S
C
3
9
P
I
R
D
Y
#
T
R
D
Y
#
T
P
3
5
8
T
P
3
0
2
+
5
V
T
3
5
5
T
P
-
1
T
1
9
7
T
P
-
1
T
P
3
5
5
1
3
9
4
-
8
1
2
3
4
5
6
7
8
9
1
0
1
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
2
0
2
1
2
2
2
3
2
4
2
5
2
6
2
7
2
8
2
9
3
0
3
1
3
2
3
3
3
4
3
5
3
6
3
7
3
8
3
9
4
0
4
1
4
2
4
3
4
4
4
5
4
6
4
7
4
8
4
9
5
0
5
1
5
2
5
3
5
4
5
5
5
6
5
7
5
8
5
9
6
0
6
1
6
2
6
3
6
4
6
5
6
6
6
7
6
8
6
9
7
0
7
1
7
2
7
3
7
4
7
5
7
6
7
7
7
8
7
9
8
0
8
1
8
2
8
3
8
4
8
5
8
6
8
7
8
8
8
9
9
0
9
1
9
2
9
3
9
4
9
5
9
6
9
7
9
8
9
9
1
0
0
1
0
1
1
0
2
1
0
3
1
0
4
1
0
5
1
0
6
1
0
7
1
0
8
1
0
9
1
1
0
1
1
1
1
1
2
1
1
3
1
1
4
1
1
5
1
1
6
1
1
7
1
1
8
1
1
9
1
2
0
C
N
3
H
R
S
-
C
O
N
N
1
2
0
B
Y
0
Y
2
Y
4
Y
6
U
V
0
U
V
2
U
V
4
U
V
6
Z
V
_
P
C
L
K
F
B
D
A
T
A
Z
V
_
L
R
C
L
K
F
B
A
C
T
#
Y
0
Y
2
Y
4
Y
6
U
V
0
U
V
2
U
V
4
U
V
6
Z
V
_
P
C
L
K
3
.
3
V
F
B
A
C
T
#
I
I
L
R
1
3
9
4
P
O
W
E
R
F
B
D
A
T
A
1
3
9
4
-
2
1
3
9
4
-
4
1
3
9
4
-
6
1
3
9
4
-
8
1
3
9
4
-
1
0
+
3
.
3
V
1
,
1
0
1
1
,
1
0
1
,
1
0
1
,
1
0
1
,
1
0
1
,
1
0
1
,
1
0
1
,
1
0
1
,
1
0
1
,
1
0
1
,
1
0
1
3
9
4
-
1
,
2
,
3
,
4
A
D
D
G
U
A
R
D
T
R
A
C
E
.
N
o
t
i
n
s
t
a
l
l
3
2
1
Q
8
S
2
N
3
9
0
6
1
2
3 4
5
6
D
1
0
R
B
7
3
1
U
C
9
1
S
C
D
1
U
1
2
C
9
2
S
T
1
0
U
Y
1
Y
3
Y
5
Y
7
U
V
1
U
V
3
U
V
5
U
V
7
Z
V
_
H
R
E
F
Z
V
_
V
R
E
F
1
3
9
4
P
O
W
E
R
I
2
C
_
C
L
K
Z
V
_
M
C
L
K
1
3
9
4
P
O
W
E
R
F
L
A
S
H
_
V
P
P
F
B
C
L
K
Y
1
Y
3
Y
5
Y
7
U
V
1
U
V
3
U
V
5
U
V
7
Z
V
_
H
R
E
F
3
.
3
V
I
I
M
C
L
K
Z
V
_
V
R
E
F
1
3
9
4
-
1
1
3
9
4
-
3
1
3
9
4
-
5
1
3
9
4
-
7
1
3
9
4
-
9
+
1
2
V
+
5
V
+
3
.
3
V
1
,
7
1
,
1
0
1
,
1
0
1
,
1
0
1
,
1
0
1
,
1
0
1
,
1
0
1
,
1
0
1
,
1
0
1
,
1
0
1
,
1
0
1
,
1
0
6
2
N
3
9
0
6
12
R
1
1
6
1
0
K
R
3
31
2
Q
9
R
N
1
4
2
4
12
R
1
4
7
1
0
K
R
3
F
L
A
S
H
_
O
N
T
P
3
0
6
T
P
3
4
2
+
1
2
V
1
P
C
I
I
D
I
N
T
B
#
R
E
Q
#
0
C
/
B
E
#
2
S
E
R
R
#
P
A
R
D
E
V
S
E
L
#
I
R
D
Y
#
Z
V
_
S
C
L
K
$
P
C
I
C
L
K
1
E
N
_
F
B
Z
V
#
I
I
S
C
L
K
I
N
T
B
#
$
F
B
_
C
L
K
R
E
Q
#
0
A
D
8
A
D
1
0
A
D
1
2
A
D
1
4
A
D
1
7
A
D
1
9
A
D
2
1
A
D
2
3
A
D
2
5
A
D
2
7
A
D
2
9
A
D
3
1
C
/
B
E
#
2
3
.
3
V
I
R
D
Y
#
D
E
V
S
E
L
#
S
E
R
R
#
P
A
R
A
D
1
9
E
N
_
F
B
Z
V
#
+
3
.
3
V
1
,
2
1
,
1
0 1
,
1
0
1
,
1
0
1
,
2
1
,
2
,
1
0
1
1
,
2
,
8
,
1
0
1
P
C
I
R
S
T
#
G
N
T
#
0
C
/
B
E
#
0
C
/
B
E
#
1
C
/
B
E
#
3
P
E
R
R
#
T
R
D
Y
#
S
T
O
P
#
I
N
T
C
#
F
R
A
M
E
#
Z
V
_
D
A
T
A
I
I
D
A
T
A
I
N
T
C
#
P
C
I
R
S
T
#
G
N
T
#
0
A
D
9
A
D
1
1
A
D
1
3
A
D
1
5
A
D
1
6
A
D
1
8
A
D
2
0
A
D
2
2
A
D
2
4
A
D
2
6
A
D
2
8
A
D
3
0
C
/
B
E
#
3
C
/
B
E
#
1
3
.
3
V
T
R
D
Y
#
S
T
O
P
#
P
E
R
R
#
C
/
B
E
#
0
F
R
A
M
E
#
+
3
.
3
V
1
1
1
,
1
0
1
,
2
,
1
0
1
,
2
,
1
0
1
,
2
,
1
0
1
,
2
,
1
0
1
,
2
,
8
,
1
0
1
,
2
,
8
,
1
0
1
,
2
,
8
,
1
0
1
,
2
,
1
0
T
3
5
6
T
P
-
1
T
3
0
9
T
P
-
1
T
3
5
8
T
P
-
1
T
3
0
2
T
P
-
1
T
3
0
6
T
P
-
1
T
1
0
4
T
P
-
1
T
1
9
5
T
P
-
1
T
1
9
8
T
P
-
1
T
1
9
9
T
P
-
1
T
2
0
0
T
P
-
1
T
2
0
1
T
P
-
1
T
2
0
2
T
P
-
1
T
2
0
3
T
P
-
1
T
2
1
3
T
P
-
1
T
P
3
5
6
T
P
3
0
9
T
P
3
5
8
T
P
3
0
2
F
L
A
S
H
_
V
P
P
1
3
9
4
-
1
1
3
9
4
-
2
1
3
9
4
-
3
1
3
9
4
-
4
1
3
9
4
-
6
1
3
9
4
-
9
1
3
9
4
-
1
0
T
3
4
2
T
P
-
1
T
1
2
4
T
P
-
1
T
2
1
4
T
P
-
1
T
P
3
0
6
T
P
3
4
2
1
3
9
4
P
O
W
E
R
1
3
9
4
-
5
1
3
9
4
-
7
A
D
[
0
.
.
3
1
]
A
D
1
A
D
3
A
D
5
A
D
7
1
,
2
,
1
0
A
D
0
A
D
2
A
D
4
A
D
6
A
d
v
a
n
c
e
d
P
C
I
I
/
F
B-14 MPB Schematic Diagrams
Figure B-3 MPB Main Board (Motherboard) Logic Diagrams (Sheet 9 of 10)
+5V
4
5
6
1
4
7
U2B
SSHC00
9
10
8
1
4
7
U2C
SSHC00
12
13
11
1
4
7
U2D
SSHC00
11
10
1
4
7
U11E
SSHC14
13 12
1
4
7
U11F
SSHC14
+5V
+5V
+5V
+5V
+5VSB
+5V
1 2
R25
10KR3
D
2
CLK
3
Q
5
Q
6
VCC
14
P
R
4
GND
7 C
L
1
U5A
SOHCT74
TP352
+5V
8
9
1
4
7 6
U22D
SOHC4066
9
10
8
1
4
7
U12C
SSHC32
12
13
11
1
4
7
U12D
SSHC32
12
13
11
1
4
7
U1D
SSHC32
+5V
+5V
1
2
R26
10KR3
TP303
1
2 L1
MLB321611
1
2
L2
MLB321611
6
4
2
1
3
5
7
9
8
CN11
KBMS-CONN
1 2
R93
47R3
1 2
R94
47R3
1
2
L3
MLB321611
1 2
F2
SPOLY100
KBCLK
KBDATA
TP117
TP42
TP41
+5V
1
1,10
15V/1.1A
SMD100
1
2
R95
47R3
1
2
R96
47R3
1
2
L6
MLB321611
1
2
F3
SPOLY100
PS2DATA
PS2CLK
TP38
TP40
TP39
+5V
1
1,10
15V/1.1A
SMD100
KEYBOARD CONN
C77
SC47P
C78
SC47P
1 2
L4
MLB321611
1
2
L5
MLB321611
6
4
2
1
3
5
7
9
8
CN12
KBMS-CONN
MOUSE CONN
C79
SC47P
C80
SC47P
1
2
L8
MLB321611
1
2
F4
SPOLY100
+5V
15V/1.1A
SMD100
1
2
R151
33R3
C114
SC47P
C115
SC47P
USBP0
USBP1
1
1
PS/2 , USB CONN.& NO USE GATE
1
2
R152
33R3
C116
SCD1U
1
2
3
4
5
6
7
8
JP1
AMP-USB-CONN
T38
TP-1
T41
TP-1
T42
TP-1
T117
TP-1
TP117
TP42
TP41
T125
TP-1
T39
TP-1
T40
TP-1
TP38
TP40
TP39
TP125
T352
TP-1
T303
TP-1
TP352
TP303
MPB Schematic Diagrams B-15
Figure B-3 MPB Main Board (Motherboard) Logic Diagrams (Sheet 10 of 10)
T
2
6
8
T
P
-
1
T
2
7
0
T
P
-
1
T
2
7
1
T
P
-
1
T
2
7
2
T
P
-
1
T
2
7
3
T
P
-
1
T
2
7
4
T
P
-
1
T
1
5
6
T
P
-
1
T
1
5
7
T
P
-
1
T
1
5
8
T
P
-
1
T
1
5
9
T
P
-
1
T
1
7
4
T
P
-
1
T
2
1
1
T
P
-
1
T
2
1
2
T
P
-
1
T
1
6
9
T
P
-
1
T
2
1
5
T
P
-
1
T
2
1
6
T
P
-
1
T
2
1
7
T
P
-
1
T
2
1
8
T
P
-
1
A
D
2
5
P
A
R
A
D
8
A
D
1
8
A
D
1
2
I
D
E
_
D
1
1
I
D
E
_
D
1
I
D
E
_
D
2
I
D
E
_
D
3
I
D
E
_
D
8
C
D
_
5
V
1
,
2
,
8
1
,
2
,
8
1
,
2
,
8
1
,
2
,
8
1
,
2
,
8
2
,3
2
,3
2
,3
2
,3
2
,3
T
4
7
T
P
-
1
T
4
8
T
P
-
1
T
4
9
T
P
-
1
T
5
0
T
P
-
1
T
5
1
T
P
-
1
T
5
2
T
P
-
1
T
1
0
7
T
P
-
1
T
1
0
8
T
P
-
1
T
1
0
9
T
P
-
1
T
1
1
1
T
P
-
1
T
1
1
3
T
P
-
1
T
1
1
5
T
P
-
1
I
D
E
_
R
S
T
#
C
D
/
F
D
D
_
R
D
Y
#
W
G
A
T
E
#
R
E
Q
#
0
7
7
N
O
C
O
N
D
K
_
M
O
S
O
N
Z
V
_
S
C
L
K
Z
V
_
D
A
T
A
U
V
7
U
V
1
$
P
C
I
C
L
K
0
U
V
5
7
1
8
6
8 8 8
88
1
5
2
T
5
T
P
-
1
T
6
T
P
-
1
T
7
T
P
-
1
T
8
T
P
-
1
T
9
T
P
-
1
T
1
0
T
P
-
1
C
R
T
_
V
S
C
R
T
_
B
Y
7
Y
5
Y
4
Y
3
A
D
1
4
Z
V
_
M
C
L
K
Y
6
Z
V
_
V
R
E
F
Z
V
_
H
R
E
F
Z
V
_
L
R
C
L
K
1
,
2
,
8
1
1
8
8 8 8 8
8 8
8
8
T
1
1
T
P
-
1
T
1
2
T
P
-
1
T
1
4
T
P
-
1
T
1
6
T
P
-
1
T
1
7
T
P
-
1
T
1
8
T
P
-
1
T
1
9
T
P
-
1
Y
1
Y
0
I
N
T
C
#
A
D
1
5
A
D
1
3
P
E
R
R
#
S
T
O
P
#
G
N
T
#
0
G
N
T
#
1
P
S
2
C
L
K
P
S
2
D
A
T
A
K
B
C
L
K
K
B
D
A
T
A
F
B
A
C
T
#
1
,
2
,
8
1
,
2
,
8
1
1
,9
1
1
,9
1 1
1
8 8
1
,
2
,
8
8
2
,8
T
8
0
T
P
-
1
T
8
1
T
P
-
1
T
8
4
T
P
-
1
T
8
5
T
P
-
1
T
8
6
T
P
-
1
T
8
7
T
P
-
1
T
9
0
T
P
-
1
T
1
1
6
T
P
-
1
T
1
1
8
T
P
-
1
T
1
1
9
T
P
-
1
T
1
2
2
T
P
-
1
T
1
2
3
T
P
-
1
T
1
2
6
T
P
-
1
T
1
2
7
T
P
-
1
C
D
_
L
O
C
K
#
A
D
2
8
A
D
3
0
C
R
T
_
H
S
C
R
T
_
R
P
C
I
R
S
T
#
E
N
_
1
3
9
4
P
W
R
U
V
3
D
K
_
S
O
U
N
D
_
L
D
K
_
S
O
U
N
D
_
R
D
K
_
H
D
L
E
D
#
F
L
A
S
H
_
O
N
E
N
_
C
H
G
R
_
R
O
M
E
N
_
F
B
Z
V
#
1
,
2
,
8
1
,
2
,
8
1
1 1
1
6
1
1
3
1
1
8
1
T
1
7
8
T
P
-
1
T
1
7
9
T
P
-
1
T
1
8
0
T
P
-
1
T
1
8
3
T
P
-
1
T
1
8
4
T
P
-
1
T
1
8
5
T
P
-
1
T
1
8
6
T
P
-
1
T
2
3
8
T
P
-
1
T
2
4
0
T
P
-
1
T
2
4
2
T
P
-
1
T
2
4
3
T
P
-
1
T
2
4
5
T
P
-
1
T
2
4
6
T
P
-
1
T
2
4
7
T
P
-
1
M
T
R
0
#
C
D
_
E
X
I
S
T
#
I
D
E
_
R
D
Y
A
D
1
6
F
R
A
M
E
#
I
R
D
Y
#
I
D
E
_
D
0
I
D
E
_
D
4
I
D
E
_
D
5
I
D
E
_
D
6
I
D
E
_
D
7
I
D
E
_
D
9
I
D
E
_
D
1
0
+
5
V
1
,
2
,
8
3
1
1
,
2
,
8
1
,2
2
,3
2
,3
2
,3
2
,3
2
,3
2
,3
2
,3
3
T
2
7
5
T
P
-
1
T
2
7
6
T
P
-
1
T
2
7
7
T
P
-
1
T
2
7
8
T
P
-
1
T
2
7
9
T
P
-
1
T
2
8
0
T
P
-
1
T
2
8
1
T
P
-
1
T
2
8
3
T
P
-
1
T
2
8
4
T
P
-
1
T
2
8
7
T
P
-
1
T
2
8
8
T
P
-
1
T
2
8
9
T
P
-
1
T
2
9
0
T
P
-
1
T
2
9
1
T
P
-
1
T
2
9
5
T
P
-
1
T
1
8
7
T
P
-
1
T
1
8
8
T
P
-
1
T
1
8
9
T
P
-
1
T
1
9
0
T
P
-
1
T
1
9
2
T
P
-
1
T
1
9
4
T
P
-
1
T
1
9
6
T
P
-
1
T
2
0
4
T
P
-
1
T
2
5
0
T
P
-
1
T
2
5
1
T
P
-
1
T
2
5
2
T
P
-
1
T
2
5
3
T
P
-
1
T
2
5
4
T
P
-
1
T
2
5
5
T
P
-
1
T
2
5
6
T
P
-
1
T
2
5
8
T
P
-
1
F
B
D
A
T
A
I
D
E
_
I
R
Q
I
D
E
_
I
O
R
#
I
D
E
_
A
1
I
D
E
_
I
O
W
#
I
D
E
_
C
S
1
#
I
D
E
_
C
S
0
#
C
/
B
E
#
2
I
D
E
_
D
1
2
I
D
E
_
D
1
3
I
D
E
_
D
1
4
I
D
E
_
D
1
5
R
E
Q
#
1
I
D
E
_
D
R
Q
0
I
D
E
_
D
A
C
K
0
#
I
D
E
_
A
2
1
,
8
2
1
,
2
,
8
3
2
,3
2
,3
2
,3
2
,3
2
2
2 22 2
2
3
T
9
1
T
P
-
1
T
9
2
T
P
-
1
T
9
3
T
P
-
1
T
9
4
T
P
-
1
T
9
5
T
P
-
1
T
9
6
T
P
-
1
T
9
7
T
P
-
1
T
9
8
T
P
-
1
T
1
2
8
T
P
-
1
T
1
2
9
T
P
-
1
T
1
3
0
T
P
-
1
T
1
3
1
T
P
-
1
T
1
3
2
T
P
-
1
T
1
3
3
T
P
-
1
T
1
3
4
T
P
-
1
T
1
3
5
T
P
-
1
A
U
D
I
O
_
C
D
_
R
R
D
A
T
A
#
D
R
0
#
I
N
D
E
X
#
S
T
E
P
#
W
D
A
T
A
#
T
R
K
0
#
H
D
S
E
L
I
2
C
_
D
A
T
A
U
S
B
P
1
U
S
B
P
0
I
2
C
_
C
L
K
D
K
_
P
J
I
N
#
A
D
9
A
D
1
9
A
D
2
3
1
,
2
,
8
1
,
2
,
8
1
,
2
,
8 1 1
3
11
1
1
3
3
3
4
1
,7
1
,
7
T
2
1
T
P
-
1
T
2
2
T
P
-
1
T
2
3
T
P
-
1
T
2
5
T
P
-
1
T
2
6
T
P
-
1
T
2
7
T
P
-
1
T
3
2
T
P
-
1
T
3
3
T
P
-
1
A
D
2
4
A
D
2
6
A
D
1
0
A
D
1
1
C
/
B
E
#
0
C
/
B
E
#
3
D
S
K
C
H
G
#
C
D
_
P
A
S
S
#
A
D
7
A
D
6
A
D
5
A
D
4
A
D
0
A
D
2
A
D
3
1
,
2
,
8
1
,
2
,
8
1
,
2
,
8
1
,
2
,
8
1
,
2
,
8
1
,
2
,
8
1
,
2
,
8
1
,
2
,
8
1
,
2
,
8
1
,
2
,
8
1
,
2
,
83
1
,
2
,
8
1
,
2
,
8
3
T
3
5
T
P
-
1
T
3
7
T
P
-
1
T
4
3
T
P
-
1
T
4
4
T
P
-
1
T
4
5
T
P
-
1
I
D
E
_
I
O
C
S
1
6
#
F
D
D
_
E
X
IS
T
#
W
R
T
P
R
T
#
Y
2
F
D
IR
F
D
D
/
P
R
T
#
Z
V
_
P
C
L
K
A
D
1
C
/
B
E
#
1
C
R
T
_
G
S
E
R
R
#
D
E
V
S
E
L
#
1
,
2
,
8
5
1
3
1
,2
3
1
8
1
,8 8
1
,
2
,
8
T
9
9
T
P
-
1
T
1
0
0
T
P
-
1
T
1
0
1
T
P
-
1
T
1
0
2
T
P
-
1
T
1
0
5
T
P
-
1
T
1
0
6
T
P
-
1
T
1
3
6
T
P
-
1
T
1
3
9
T
P
-
1
T
1
4
0
T
P
-
1
T
1
4
2
T
P
-
1
T
1
4
3
T
P
-
1
T
1
5
5
T
P
-
1
I
D
E
_
A
0
U
V
2
$
P
C
IC
L
K
1
U
V
4
U
V
6
U
V
0
A
D
2
1
A
D
2
2
A
D
2
0
A
D
2
7
A
D
3
1
A
D
2
9
1
,2
,8
1
,
2
,
8
1
,
2
,
8
1
,2
,8
1
,
2
,
8
1
,
2
,
8
8 8 8 8
1
2
T
2
0
5
T
P
-
1
T
2
0
6
T
P
-
1
T
2
0
7
T
P
-
1
T
2
0
8
T
P
-
1
T
2
0
9
T
P
-
1
T
2
1
0
T
P
-
1
T
2
5
9
T
P
-
1
T
2
6
0
T
P
-
1
T
2
6
3
T
P
-
1
T
2
6
4
T
P
-
1
T
2
6
5
T
P
-
1
T
2
6
6
T
P
-
1
T
R
D
Y
#
A
D
1
7
A
U
D
IO
_
C
D
_
L
D
O
C
K
P
W
O
K
I
R
Q
1
5
IN
T
B
#
C
S
I
1
,
2
,
8
3
1
2
6
1
,
2
,
8
T
3
3
1
T
P
-
1
T
3
6
2
T
P
-
1
A
M
P
_
5
V
T
3
6
5
T
P
-
1
T
3
6
6
T
P
-
1
T
3
6
8
T
P
-
1
D
K
_
B
L
1
#
D
K
_
B
L
2
#
C
S
O
77
7
T
3
6
9
T
P
-
1
T
3
7
0
T
P
-
1
T
3
7
1
T
P
-
1
D
K
_
C
H
G
_
L
E
D
C
H
A
R
G
E
R
_
O
N
+
5
V
S
B
71
B-16 MPB Schematic Diagrams
Figure B-4 MPB VGA Board Logic Diagrams (Sheet 1 of 5)
$VGACLK
2
2
CRT_R
CRT_G
DEVSEL#
RGBGND
2
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
CN2
HRS-CONN140
CRT_VS
CRT_HS
CRT_R
CRT_G
CRT_VS
CRT_HS
RGBGND
2
2
2
2
2
C/BE#[0..3]
Y[0..7]
UV[0..7]
ENAVEE
AD[0..31]
Y[0..7]
UV[0..7]
C/BE#[0..3]
AD[0..31]
C52
SCD1U
2
4
2
2
C10
SCD1U
C29
SCD1U
ZV_VREF
DISPLAY
DDC_DATA
DDC_CLK
C/BE#0
ENAVEE
ZV_HREF
ZV_VREF
ZV_PCLK DISPLAY
CRT_B
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
AD8
AD9
AD10
AD11
AD12
AD13
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
UV0
UV1
UV2
UV3
UV4
+5V
2
2
2
4
1
2
R10
47R3
C17
SC39P
1
2
R22
47R3
C40
SC39P
ZV_HREF
ZV_PCLK
CRT_B
LCDVEE
FRAME#
+5V
C53
SCD1U
1
2
R11
47R3
C25
SC39P
TRDY#
CLOSE VGA C
1
2
R9
47R3
C15
SC39P
2
2
2
2
2
2
5
2
2
2
1
2
R23
47R3
C41
SC39P
PERR#
IRDY#
DEVSEL#
PAR
PCIRST#
STNDBY#
3.3V/5V#
$VGACLK
$VGA_14M
@32K2
IRDY#
2
2
2
2
TRDY#
STOP#
SERR#
FRAME#
C/BE#1
C/BE#2
C/BE#3
TRDY#
STOP#
SERR#
PERR#
IRDY#
DEVSEL#
PAR
PCIRST#
$VGA_14M
$VGACLK
3.3V/5V#
STNDBY#
FRAME#
AD14
AD15
AD16
AD17
AD18
AD19
AD20
AD21
AD22
AD23
AD24
AD25
AD26
AD27
AD28
AD29
AD30
AD31
@32K2
UV5
UV6
UV7
C44
SCD1U
C43
SCD1U
+3.3V
VGA BOARD CONNECTOR
+3.3V
MPB Schematic Diagrams B-17
Figure B-4 MPB VGA Board Logic Diagrams (Sheet 2 of 5)
33 3 333
1
2
3
4
5 6 7 8
R
P
8
S
R
N
3
3
C
2
8
S
C
D
1
U
C
1
8
S
C
D
1
U
1234
5
6
7
8
R
P
7
S
R
N
3
3
R
A
S
A
#
R
A
S
B
#
C
A
S
A
H
#
C
A
S
A
L
#
W
E
A
#
W
E
B
#
P
R
A
S
A
#
P
R
A
S
B
#
P
C
A
S
A
H
#
P
C
A
S
A
L
#
P
W
E
A
#
P
W
E
B
#
C
2
S
C
1
0
U
1
6
V
C
1
2
S
C
D
1
U
+
5
V
V
G
A
P
W
R
V
R
A
M
V
C
C
D
V
C
C
A
V
C
C
C
V
C
C
0
C
V
C
C
1
+
5
V
3
V
A
A
[
0
..8
]
VMAD1
VMAD2
VMAD3
VMAD4
VMAD5
VMAD6
VMAD7
VMAD8
VMAD9
VMAD10
VMAD11
VMAD12
VMAD13
VMAD14
VMAD15
VMBD0
VMBD1
VMBD2
VMBD3
VMBD4
VMBD5
VMBD6
VMBD7
VMBD8
VMBD9
VMBD10
VMBD11
VMBD12
VMBD13
VMBD14
VMBD15
VAA0
VAA1
VAA2
VAA3
VAA4
VAA5
VAA6
VAA7
VAA8
3
3
1
2
R
2
1
4
K
7
R
3
1
2
R
2
4
3
3
R
3
ID
S
E
L
1
1
IR
D
Y
#
2
3
S
T
O
P
#
2
7
D
E
V
S
E
L
#
2
5
P
A
R
3
1
C
/B
E
3
#
1
0
R
E
S
E
T
#
2
0
7
C
/B
E
1
#
3
2
T
R
D
Y
#
2
4
AD18
18
AD17
19
F
R
A
M
E
#
2
2
C
/B
E
0
#
4
3
C
/B
E
2
#
2
1
R
O
M
A
0
1
7
9
R
O
M
A
1
1
8
0
R
O
M
A
2
1
8
2
R
O
M
A
3
1
8
3
R
O
M
A
4
1
8
5
R
O
M
A
1
0
1
8
6
R
O
M
A
5
1
8
7
R
O
M
A
6
1
8
9
R
O
M
A
9
1
9
0
R
O
M
A
7
1
9
1
R
O
M
A
8
1
9
2
R
O
M
A
1
2
1
9
3
R
O
M
A
1
3
1
9
4
R
O
M
A
1
5
1
9
5
R
O
M
A
1
4
1
9
6
R
O
M
A
1
6
1
9
7
R
O
M
A
1
7
1
9
8
AD00
51
AD01
50
AD02
49
AD03
48
AD04
47
AD05
46
AD06
45
AD07
44
AD08
41
AD09
40
AD10
38
AD11
37
AD12
36
AD13
35
AD14
34
AD15
33
R
E
F
C
L
K
2
0
3
(
R
E
S
E
R
V
E
D
)
2
0
4
S
T
N
D
B
Y
#
1
7
8
AVCC
59
AGND
56
BVCC
9
BVCC
42
DVCC
66
IVCC
80
MVCCC
108
IGND
77
MGNDC
105
MGNDB
139
IGND
184
BGND
12
BGND
26
BGND
39
DGND
63
MAD8
170
MAD9
171
MAD10
172
MAD11
173
MAD12
174
MAD13
175
MAD14
176
MAD15
177
AA0
145
AA1
146
AA2
147
AA3
148
AA4
149
AA5
150
AA6
151
AA7
152
AA8
153
R
A
S
A
#
1
5
6
C
A
S
A
H
#
1
5
9
MBD1
128
MBD2
129
MBD3
130
MBD4
131
MBD5
132
MBD6
133
MBD7
134
P
0
7
1
P
1
7
2
P
2
7
3
P
3
7
4
P
4
7
5
P
5
7
6
P
6
7
8
P
7
7
9
L
P
6
8
F
L
M
6
7
S
H
F
C
L
K
7
0
E
N
A
V
D
D
6
2
R
6
0
G
5
8
B
5
7
H
S
Y
N
C
6
5
V
S
Y
N
C
6
4
R
O
M
A
1
1
1
8
8
E
N
A
V
E
E
6
1
AD16
20
MAD0
162
MAD1
163
MAD2
164
MAD3
165
MAD4
166
MAD5
167
MAD6
168
MAD7
169
3
2
K
H
Z
1
5
4
C
A
S
A
L
#
1
6
0
W
E
A
#
1
5
7
MBD0
127
MBD8
135
MBD9
136
MBD10
137
MBD11
138
MBD12
140
MBD13
141
MBD14
143
MBD15
144
R
A
S
B
#
1
2
3
C
A
S
B
H
#
1
2
5
C
A
S
B
L
#
1
2
6
W
E
B
#
1
2
4
P
8
8
1
P
9
8
2
P
1
0
8
3
P
1
1
8
4
P
1
2
8
5
P
1
3
8
6
P
1
4
8
7
P
1
5
8
8
A
C
T
I
5
3
E
N
A
B
K
L
5
4
M
6
9
A
2
0
1
9
9
R
O
M
O
E
#
2
0
0
C
L
K
2
0
1
A
2
3
2
8
S
E
R
R
#
3
0
MVCCB
142
IVCC
181
CVCC0
205
CVCC1
206
CGND0
202
CGND1
208
R
S
E
T
5
5
P
E
R
R
#
2
9
AD19
17
AD20
16
AD21
15
AD22
14
AD23
13
AD24
8
AD25
7
AD26
6
AD27
5
AD28
4
AD29
3
AD30
2
AD31
1
M
C
D
0
1
0
6
M
C
D
1
1
0
7
M
C
D
2
1
0
9
M
C
D
3
1
1
0
M
C
D
4
1
1
1
M
C
D
5
1
1
2
M
C
D
6
1
1
3
M
C
D
7
1
1
4
M
C
D
8
1
1
5
M
C
D
9
1
1
6
M
C
D
1
0
1
1
7
M
C
D
1
1
1
1
8
M
C
D
1
2
1
1
9
M
C
D
1
3
1
2
0
M
C
D
1
4
1
2
1
M
C
D
1
5
1
2
2
CA0
90
CA1
91
CA2
92
CA3
93
CA4
94
CA5
95
CA6
96
CA7
97
CA8
98
HREF
99
R
A
S
C
#
1
0
1
C
A
S
C
H
#
1
0
3
C
A
S
C
L
#
1
0
4
W
E
C
#
1
0
2
O
E
C
#
1
0
0
BGND
52
DGND
89
MVCCA
158
MGNDA
161
O
E
A
B
#
1
5
5
U
4
C
T
6
5
5
5
0
1
2
3
4
5 6 7 8
R
P
9
S
R
N
4
K
7
V
M
A
D
[
0
..1
5
]
V
M
B
D
[
0
.
.1
5
]
VMAD0
A
D
2
2
V
A
A
0
V
A
A
5
S
B
1
11 1 111
1
IR
D
Y
#
T
R
D
Y
#
D
E
V
S
E
L
#
S
T
O
P
#
P
A
R
F
R
A
M
E
#
P
C
I
R
S
T
#
C
/B
E
#
[
0
..3
]
C
/B
E
#
0
C
/B
E
#
1
C
/B
E
#
2
C
/B
E
#
3
1
2
G
1
G
A
P
-
C
L
O
S
E
S
B
6
5
5
5
0
-
B
1
2
R
1
2
3
3
R
3
V
R
A
M
O
E
#
Y
0
Y
1
Y
2
33
3
1
2
3
4
5 6 7 8
R
P
5
S
R
N
2
2
1
2
3
4
5 6 7 8
R
P
6
S
R
N
2
2
1
2
3
4
5 6 7 8
R
P
3
S
R
N
2
2
1
2
3
4
5 6 7 8
R
P
4
S
R
N
2
2
1
2
3
4
5
6
7
8
9
1
0
2
0
1
9
1
8
1
7
1
6
1
5
1
4
1
3
1
2
1
1
U
3
Q
P
R
N
-
R
2
7
C
1
5
1
2
3
4
5
6
7
8
9
1
0
2
0
1
9
1
8
1
7
1
6
1
5
1
4
1
3
1
2
1
1
U
2
Q
P
R
N
-
R
2
7
C
1
5
C
A
S
B
H
#
C
A
S
B
L
#
U
D
[
0
.
.3
]
L
D
[
0
..
3
]
U
D
3
U
D
2
U
D
1
U
D
0
L
D
3
L
D
2
L
D
1
L
D
0
S
U
D
3
S
U
D
2
S
U
D
1
S
U
D
0
S
U
D
7
P
C
A
S
B
H
#
P
C
A
S
B
L
#
1
1 1
111
S
U
D
[
0
..7
]
C
R
T
_
G
C
R
T
_
R
C
R
T
_
B
C
R
T
_
H
S
C
R
T
_
V
S
S
U
D
6
S
U
D
4
S
U
D
5
RGBH
S
Y
N
C
V
S
Y
N
C
1
1
12
R
5
7
5
R
3
12
R
6
7
5
R
3
12
R
7
7
5
R
3
Y
[
0
..7
]
U
V
[
0
..7
]
Z
V
_
P
C
L
K
Y
3
Y
4
Y
5
Y
6
Y
7
U
V
0
U
V
1
U
V
2
U
V
3
U
V
4
U
V
5
U
V
7
U
V
6
Z
V
_
P
C
L
K
1 1
1
11
1
11
4
444
1
2
R
1
8
1
0
R
3
1
2
R
1
9
1
0
R
3
1
2
R
2
0
1
0
R
3
1
2
R
1
7
1
0
R
3
C
3
3
S
C
4
7
P
C
3
4
S
C
4
7
P
C
3
5
S
C
3
3
P
C
3
6
S
C
3
3
P
C
3
7
S
C
3
3
P
S
H
F
C
L
KM
O
D
L
P
L
F
S
$
V
G
A
_
1
4
M
P
E
R
R
#
S
E
R
R
#
D
D
C
_
D
A
T
A
D
D
C
_
C
L
K
@
3
2
K
2
$
V
G
A
C
L
K
S
T
N
D
B
Y
#
R
G
B
G
N
D
1
1
5
4 A
D
[
0
.
.3
1
]
E
N
A
V
E
E
E
N
A
V
D
D
R
[
0
..7
]
AD0
R
0
R
1
R
2
R
3
R
4
R
5
R
6
R
7
1 2 3 4 5 6 7 8 9 1
0
2
0
1
9
1
8
1
7
1
6
1
5
1
4
1
3
1
2
1
1
U
1
Q
P
R
N
-
R
2
7
C
1
5
1 2 3 4
5
6
7
8
R
P
2
S
R
N
2
2
1 2 3 4
5
6
7
8
R
P
1
S
R
N
2
2
AD1
AD2
AD3
AD4
AD5
AD6
AD7
AD8
AD9
AD10
AD11
AD12
AD13
AD14
AD15
AD16
AD17
AD18
AD19
AD20
AD21
AD22
AD23
AD24
AD25
AD26
AD27
AD28
AD29
AD30
AD31
ZV_HREF
ZV_VREF
V
G
A
C
O
N
T
R
O
L
L
E
R
1 1
12
R
8
5
6
0
R
3
Z
V
_
H
R
E
F
Z
V
_
V
R
E
F
R
G
B
G
N
D
R
G
B
G
N
D
R
G
B
G
N
D
R
G
B
G
N
D
B-18 MPB Schematic Diagrams
Figure B-4 MPB VGA Board Logic Diagrams (Sheet 3 of 5)
V
M
A
D
8
V
M
A
D
9
V
M
A
D
1
0
V
M
A
D
1
1
V
M
A
D
1
2
V
M
A
D
1
3
V
M
A
D
1
4
V
M
A
D
1
5
V
C
C
1
D
Q
0
2
D
Q
1
3
D
Q
2
4
D
Q
3
5
V
C
C
6
D
Q
4
7
D
Q
5
8
D
Q
6
9
D
Q
7
1
0
N
.
C
1
1
N
.
C
1
2
N
.
C
1
3
N
.
C
1
4
W
E
1
5
R
A
S
1
6
N
.
C
1
7
A
0
1
8
A
1
1
9
A
2
2
0
A
3
2
1
V
C
C
2
2
V
S
S
4
4
D
Q
1
5
4
3
D
Q
1
4
4
2
D
Q
1
3
4
1
D
Q
1
2
4
0
V
S
S
3
9
D
Q
1
1
3
8
D
Q
1
0
3
7
D
Q
9
3
6
D
Q
8
3
5
N
.
C
3
4
N
.
C
3
3
N
.
C
3
2
L
C
A
S
3
1
U
C
A
S
3
0
O
E
2
9
A
8
2
8
A
7
2
7
A
6
2
6
A
5
2
5
A
4
2
4
V
S
S
2
3
U
1
2
S
2
5
6
K
1
6
-
6
0
C
4
2
S
C
D
1
U
V
M
A
D
0
V
M
A
D
1
V
M
A
D
2
V
M
A
D
3
V
M
A
D
4
V
M
A
D
5
V
M
A
D
6
V
M
A
D
7
V
R
A
M
V
C
C
2
2
2
V
C
C
1
D
Q
0
2
D
Q
1
3
D
Q
2
4
D
Q
3
5
V
C
C
6
D
Q
4
7
D
Q
5
8
D
Q
6
9
D
Q
7
1
0
N
.
C
1
1
N
.
C
1
2
N
.
C
1
3
N
.
C
1
4
W
E
1
5
R
A
S
1
6
N
.
C
1
7
A
0
1
8
A
1
1
9
A
2
2
0
A
3
2
1
V
C
C
2
2
V
S
S
4
4
D
Q
1
5
4
3
D
Q
1
4
4
2
D
Q
1
3
4
1
D
Q
1
2
4
0
V
S
S
3
9
D
Q
1
1
3
8
D
Q
1
0
3
7
D
Q
9
3
6
D
Q
8
3
5
N
.
C
3
4
N
.
C
3
3
N
.
C
3
2
L
C
A
S
3
1
U
C
A
S
3
0
O
E
2
9
A
8
2
8
A
7
2
7
A
6
2
6
A
5
2
5
A
4
2
4
V
S
S
2
3
U
1
0
S
2
5
6
K
1
6
-
6
0
C
1
6
S
C
D
1
U
C
3
9
S
C
D
1
U
V
A
A
[
0
.
.
8
]
W
E
A
#
R
A
S
A
#
V
A
A
0
V
A
A
1
V
A
A
2
V
A
A
3
W
E
A
#
R
A
S
A
#
V
R
A
M
V
C
C
M
5
M
4
4
2
5
6
2 22
C
A
S
A
H
#
C
A
S
A
L
#
V
R
A
M
O
E
#
V
A
A
4
V
A
A
5
V
A
A
6
V
A
A
7
V
A
A
8
C
A
S
A
H
#
C
A
S
A
L
#
O
E
#
2 2
V
C
C
1
D
Q
0
2
D
Q
1
3
D
Q
2
4
D
Q
3
5
V
C
C
6
D
Q
4
7
D
Q
5
8
D
Q
6
9
D
Q
7
1
0
N
.
C
1
1
N
.
C
1
2
N
.
C
1
3
N
.
C
1
4
W
E
1
5
R
A
S
1
6
N
.
C
1
7
A
0
1
8
A
1
1
9
A
2
2
0
A
3
2
1
V
C
C
2
2
V
S
S
4
4
D
Q
1
5
4
3
D
Q
1
4
4
2
D
Q
1
3
4
1
D
Q
1
2
4
0
V
S
S
3
9
D
Q
1
1
3
8
D
Q
1
0
3
7
D
Q
9
3
6
D
Q
8
3
5
N
.
C
3
4
N
.
C
3
3
N
.
C
3
2
L
C
A
S
3
1
U
C
A
S
3
0
O
E
2
9
A
8
2
8
A
7
2
7
A
6
2
6
A
5
2
5
A
4
2
4
V
S
S
2
3
U
5
S
2
5
6
K
1
6
-
6
0
C
A
S
B
H
#
C
A
S
B
L
#
V
A
A
4
V
A
A
5
V
A
A
6
V
A
A
7
V
A
A
8
C
A
S
B
H
#
C
A
S
B
L
#
O
E
#
V
M
B
D
8
V
M
B
D
9
V
M
B
D
1
0
V
M
B
D
1
1
V
M
B
D
1
2
V
M
B
D
1
3
V
M
B
D
1
4
V
M
B
D
1
5
2
2
C
3
1
S
C
D
1
U
R
A
S
B
#
W
E
B
#
V
A
A
0
V
A
A
1
V
A
A
2
V
A
A
3
W
E
B
#
R
A
S
B
#
V
M
B
D
0
V
M
B
D
1
V
M
B
D
2
V
M
B
D
3
V
M
B
D
4
V
M
B
D
5
V
M
B
D
6
V
M
B
D
7
V
A
A
4
V
A
A
5
V
A
A
6
V
A
A
7
V
A
A
8
C
A
S
B
H
#
C
A
S
B
L
#
O
E
#
V
M
B
D
8
V
M
B
D
9
V
M
B
D
1
0
V
M
B
D
1
1
V
M
B
D
1
2
V
M
B
D
1
3
V
M
B
D
1
4
V
M
B
D
1
5
V
R
A
M
V
C
C
2
C
3
8
S
C
D
1
U
V
M
B
D
[
0
.
.
1
5
]
W
E
A
#
R
A
S
A
#
V
A
A
0
V
A
A
1
V
A
A
2
V
A
A
3
V
M
B
D
0
V
M
B
D
1
V
M
B
D
2
V
M
B
D
3
V
M
B
D
4
V
M
B
D
5
V
M
B
D
6
V
M
B
D
7
M
5
M
4
4
2
5
6
2
M
V
R
A
M
C
1
9
S
C
D
1
U
M
5
M
4
4
2
5
6
V
C
C
1
D
Q
0
2
D
Q
1
3
D
Q
2
4
D
Q
3
5
V
C
C
6
D
Q
4
7
D
Q
5
8
D
Q
6
9
D
Q
7
1
0
N
.
C
1
1
N
.
C
1
2
N
.
C
1
3
N
.
C
1
4
W
E
1
5
R
A
S
1
6
N
.
C
1
7
A
0
1
8
A
1
1
9
A
2
2
0
A
3
2
1
V
C
C
2
2
V
S
S
4
4
D
Q
1
5
4
3
D
Q
1
4
4
2
D
Q
1
3
4
1
D
Q
1
2
4
0
V
S
S
3
9
D
Q
1
1
3
8
D
Q
1
0
3
7
D
Q
9
3
6
D
Q
8
3
5
N
.
C
3
4
N
.
C
3
3
N
.
C
3
2
L
C
A
S
3
1
U
C
A
S
3
0
O
E
2
9
A
8
2
8
A
7
2
7
A
6
2
6
A
5
2
5
A
4
2
4
V
S
S
2
3
U
1
1
S
2
5
6
K
1
6
-
6
0
V
M
A
D
8
V
M
A
D
9
V
M
A
D
1
0
V
M
A
D
1
1
V
M
A
D
1
2
V
M
A
D
1
3
V
M
A
D
1
4
V
M
A
D
1
5
C
3
0
S
C
D
1
U
V
M
A
D
0
V
M
A
D
1
V
M
A
D
2
V
M
A
D
3
V
M
A
D
4
V
M
A
D
5
V
M
A
D
6
V
M
A
D
7
V
R
A
M
V
C
C
V
A
A
0
V
A
A
1
V
A
A
2
V
A
A
3
W
E
B
#
R
A
S
B
#
C
1
3
S
C
D
1
U
V
M
A
D
[
0
.
.
1
5
]
V
A
A
4
V
A
A
5
V
A
A
6
V
A
A
7
V
A
A
8
C
A
S
A
H
#
C
A
S
A
L
#
O
E
#
M
5
M
4
4
2
5
6
2
MPB Schematic Diagrams B-19
)
Figure B-4 MPB VGA Board Logic Diagrams (Sheet 4 of 5)
R4
R5
R6
1
2
3
4
5 6
7
8
9
10
CP1
SRP1K-2
R0
R1
R2
R3
SUD0
SUD1
SUD2
SUD3
UD0
UD1
UD2
UD3
R7
SUD4
SUD5
SUD6
SUD7
LD0
LD1
LD2
LD3
1
2
3
4
5 6
7
8
9
10
CP2
SRP1K-2
1
2
3
4
5 6
7
8
9
10
CP3
SRP1K-2
CHIP CAPACITOR
2
1
2 R2
10R3
LP
CLK
1
3
2
NF1
STC222B
SB
2
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
CN1
JAE-CONN80C
C3
SC47P
1 2
R15
22R3
R[0..7]
SUD[0..7]
UD3
R1
R2
R3
R4
R5
R6
R7
R0
SUD2
SUD1
SUD6
SUD5
SUD3
SUD0
SUD7
SUD4
2
2
1 2
R13
22R3
LFS
2
1
2
2
2
2
5
C26
SCD1U
C1
SC10U16V
1 2
R14
22R3
1
2
R1
100KR3
MOD
LCD_3/5V#
LCD_3/5V#
LCDPWR
+5V
+3.3V
+3.3V
2
2
2
1
2
R16
0R3
UD0
LD3
LD1
LD0
UD1
LD2
UD2
LCDVEE
LCD I/F
1 DISPLAY
C51
SCD1U
1
2
1
4
7
U13A
SSHC04
3
4
1
4
7
U13B
SSHC04
LVC ,VHC OR LCX
B-20 MPB Schematic Diagrams
Figure B-4 MPB VGA Board Logic Diagrams (Sheet 5 of 5)
5
V
I
N
7
3
.
3
V
I
N
6
S
R
8
V
C
C
2
V
C
C
3
S
1
5
S
2
4
GND
1
U
7
S
I
9
7
0
6
D
Y
2
3
1
147
U
9
A
S
S
H
C
0
2
+
5
V
+
3
.
3
V
V
G
A
P
W
R
+
3
.
3
V
1
1
1
2
1
3
147
U
9
D
S
S
H
C
0
2
+
3
.
3
V
+
3
.
3
V
C
4S
C
1
0
0
0
P
5
0
V
3
M
X
C
4
9
S
C
1
0
U
1
6
V
C
4
8
S
C
1
U
1
6
V
5
Z
Y
V
G
A
P
W
R
D
V
C
C
C
l
o
s
e
1
0
5
(
M
G
N
D
C
)
,
1
0
8
(
M
V
C
C
C
)
P
I
N
C
5
0
S
C
D
1
U
C
6
S
C
D
1
U
C
5
S
C
1
0
U
1
6
V
C
1
4
S
C
D
1
U
C
2
0
S
C
1
0
U
1
6
V
C
1
1
S
C
1
0
U
1
6
V
V
R
A
M
V
C
C
C
l
o
s
e
6
6
(
D
V
C
C
)
P
I
N
&
6
3
,
8
9
(
G
N
D
)
P
I
N
+
5
V
+
3
.
3
V
1
2
R
3
1
0
R
3
1
2
R
3
2
D
U
M
M
Y
-
R
3
1
5
6
4
147
U
9
B
S
S
H
C
0
2
12
R
2
7
1
0
0
K
R
3
C
2
7
S
C
D
1
U
3
.
3
V
/
5
V
#
+
3
.
3
V
1
3
1
2
147
U
1
3
F
S
S
H
C
0
4
5
V
I
N
7
3
.
3
V
I
N
6
S
R
8
V
C
C
2
V
C
C
3
S
1
5
S
2
4
GND
1
U
6
S
I
9
7
0
6
D
Y
L
C
D
P
W
R
5
V
I
N
7
3
.
3
V
I
N
6
S
R
8
V
C
C
2
V
C
C
3
S
1
5
S
2
4
GND
1
U
8
S
I
9
7
0
6
D
Y
D
V
C
C
8
9
1
0
147
U
9
C
S
S
H
C
0
2
+
3
.
3
V
5
6
147
U
1
3
C
S
S
H
C
0
4
+
3
.
3
V
9
8
147
U
1
3
D
S
S
H
C
0
4
+
3
.
3
V
L
V
C
,
V
H
C
O
R
L
C
X
N
O
T
I
N
S
.
2
4
C
4
6
S
C
D
0
1
U
C
2
2
S
C
D
0
1
U
C
2
1
S
C
D
1
U
C
4
7
S
C
D
1
U
E
N
A
V
D
D
L
C
D
_
3
/
5
V
#
C
V
C
C
1
C
V
C
C
0
R
G
B
G
N
D
1
1
1
0
147
U
1
3
E
S
S
H
C
0
4
+
3
.
3
V
C
3
2
S
C
D
1
U
C
4
5
S
C
D
1
U
1
2
R
2
5
3
3
R
3
1
2
R
2
6
3
3
R
3
C
2
4
S
C
1
0
U
1
6
V
C
2
3
S
C
1
0
U
1
6
V
V
G
A
P
W
R
1
2
L
4
H
F
7
0
A
C
B
C
7
S
C
1
0
U
1
6
V
C
8
S
C
D
0
1
U
C
9
S
C
D
1
U
A
V
C
C
R
G
B
G
N
D
R
G
B
G
N
D
V
O
L
T
A
G
E
S
W
I
T
C
H
L
C
D
_
3
/
5
V
#
E
N
A
V
D
D
0
0
0
1
1
0
1
1
L
C
D
P
W
R
S
1
S
2
0100
0001
MPB Schematic Diagrams B-21
)
Figure B-5 MPB DC In Board Logic Diagrams (Sheet 1 of 1)
1
2
3
4
5
C
N
2
P
H
-
J
K
1
1
A
U
D
_
G
N
D
C
3
S
C
1
0
0
P
2
5
V
3
K
N
C
4
S
C
1
0
0
P
2
5
V
3
K
N
C
5
S
C
1
0
0
P
2
5
V
3
K
N
C
6
S
C
1
0
0
P
2
5
V
3
K
N
D
K
_
P
J
I
N
#
1
2
L
4
H
F
7
0
A
C
B
1
2
L
5
H
F
7
0
A
C
B
L
I
N
E
_
O
U
T
_
L
L
I
N
E
_
O
U
T
_
R
D
K
_
L
I
N
E
I
N
_
L
C
9
S
C
1
0
0
P
2
5
V
3
K
N
C
1
1
S
C
1
0
0
P
2
5
V
3
K
N
1
2
L
1
H
F
7
0
A
C
B
1
2
3
4
5
C
N
1P
H
-
J
K
1
1
C
7
S
C
1
0
0
0
P
5
0
V
3
J
N
1
2
R
3
1
0
K
R
3
1
2
3
4
5
C
N
3
P
H
+
5
V
A
U
D
_
G
N
D
12
R
2
1
0
0
K
R
3
C
1
0
S
C
1
0
0
P
2
5
V
3
K
N
C
1
2
S
C
1
0
0
P
2
5
V
3
K
N
C
1
3
S
C
1
0
0
P
2
5
V
3
K
N
C
1
4
S
C
1
0
0
P
2
5
V
3
K
N
C
1
6
S
C
D
1
U
1
2
L
2
H
F
7
0
A
C
B
D
K
_
L
I
N
E
I
N
_
R
D
K
_
M
I
C
D
K
_
M
I
C
_
P
J
I
N
C
8
S
C
1
0
0
0
P
5
0
V
3
J
N
12
R
1
1
0
K
R
3
1
2
L
3
H
F
7
0
A
C
B
C
1
5
A
U
D
_
G
N
D
D
K
_
P
J
I
N
#
+
5
V
L
I
N
E
_
O
U
T
_
L
L
I
N
E
_
O
U
T
_
R
D
K
_
L
I
N
E
I
N
_
L
D
K
_
L
I
N
E
I
N
_
R
D
K
_
M
I
C
A
D
+
A
U
D
_
G
N
D
D
K
_
M
I
C
_
P
J
I
N
2
4
6
8
1
0
1
2
1
4
1
6
1
8
2
0
3
5
7
9
1
1
1
3
1
5
1
7
1
9
1
C
N
4
H
R
S
-
C
O
N
N
2
0
D
A
U
D
_
G
N
D
1
2
3
4
J
K
1
M
O
J
-
D
2
1
C
2
S
C
1
0
0
0
P
5
0
V
3
J
N
C
1
7
S
C
D
1
U
2
1
4
3
T
R
6
S
B
T
-
0
3
0
8
W
C
1
S
C
D
1
U
A
D
+
B-22 MPB Schematic Diagrams
Figure B-6 MPB LED Board Logic Diagrams (Sheet 1 of 1)
2
1
3
SW1
SW-SPVE1
COVER_SW
1
2
3
4
SW2
SKQGAB
POWER_SW2
+5VSB
+5V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
CN1
MOLEX-CON16
M+5V
1
2
CN2
MICROPHONE
+5V
+5VSB
COVER_SW
NLOCK_LED
CLOCK_LED
CHARGE_LED
STANDBY_LED
HDD/FDD_LED
POWER_SW2
POWER_LED
NUMBER LOCK
1 2
LED2
LED-G
1 2
R3
1KR3
NLOCK_LED
+5V
POWER LED
CAPS LOCK
1 2
LED1
LED-G
1 2
LED3
LED-G
1 2
R1
1KR3
1 2
R4
1KR3
CLOCK_LED
POWER_LED
+5V
STANDBY LED
1 2
LED4
LED-G
1 2
R5
1KR3
1 2
LED6
LED-G
CHARGE_LED
STANDBY_LED
+5V
+5V
HD/FD/CD LED
CHARGING LED
1 2
LED5
LED-G
1 2
R2
1KR3
1 2
R6
1KR3
HDD/FDD_LED
POST BIOS C-1
C
POST BIOS
C.1 Introduction
This section contains a listing of the POST BIOS calls for the Extensa 900 Series
Notebook.
;----------------------------------------------------------------------------
; Make sure we entered POST in real mode
; Determine the CPU type
; Convert all segment limits to 4GB
;----------------------------------------------------------------------------
002H post Verify Real Mode
004H cpu Get Type J
006H post Hardware Initialize
024H postSetHugeESJ
;----------------------------------------------------------------------------
; Initialize the chipset
; Set the in-POST flag
; Autosize the RAM
; Clear the base RAM
; Test the base RAM
; Autosize the cache
; Shadow the BIOS
;----------------------------------------------------------------------------
008H cs Initialize
011H post Reg Initialize J
00EH io Initialize OPTIONAL
00CH cache Initialize
016H post Checksum Test
018H post Timer Init
017H cache Pre Ram Auto size, OPTIONAL
028H cs Ram Auto size
03AH cache Auto size
02AH post Zero Base Ram
02CH post Real Address Test
030H post Base Ram Test
02FH cache Pre Sys Shadow OPTIONAL
038H cs System Shadow Config
020H post Refresh Test, FAR
009H post Set In Post Flag, FAR
;----------------------------------------------------------------------------
; Initialize all the hardware to a known state
;----------------------------------------------------------------------------
00AH cpu Initialize
00BH cpu Cache On
00FH fdiskInitializeJ
010H pmInitializeJ, OPTIONAL
;----------------------------------------------------------------------------
; Perform hardware tests, and further initialization
;----------------------------------------------------------------------------
014H post I8742 Init, FAR
C-2 POST BIOS
01AH post Dma InitJ, FAR
01CH post Reset PIC
;----------------------------------------------------------------------------
; Test the keyboard controller
; Compute the CPU clock speed
; Test the CMOS RAM
;----------------------------------------------------------------------------
022H post I8742 Test, FAR
032H post Compute Speed, FAR
034H post Cmos Test, FAR
;----------------------------------------------------------------------------
; Optimize chipset timing
; Optimize other hardware
;----------------------------------------------------------------------------
03CH cs Adv Config
03DH post Adv Reg Config, OPTIONAL
;----------------------------------------------------------------------------
; Initialize interrupt vectors
; Make sure ROM copyright notice is intact
; Check for configuration errors
; Initialize the video
; Shadow the video
; Display the copyright notice
; Display the CPU type
; Initialize EISA bus
; Set segment limits back to 4GB (PCI code may have changed them)
;----------------------------------------------------------------------------
042H post Vector Init, FAR
046H post Copyright Check, FAR
047H pci Op Rom Init
049H pci Init
048H post Config Check, FAR
04AH pci Video Init
04CH cs Video Shadow Config
024H postSetHugeESJ
;----------------------------------------------------------------------------
; Test and initialize the keyboard
; Check for unexpected interrupts
; Display prompt "Press F2 to enter SETUP"
;----------------------------------------------------------------------------
052H post KB Test, FAR
054H feat Setup Keyclick, OPTIONAL, FAR
076H post Keyboard Test, FAR
058H post Hot Interrupt Test, FAR
;----------------------------------------------------------------------------
; Initialize QuietBoot if it's installed
; Note: Both the keyboard and timer interrupts (IRQ0 and IRQ1) are enabled
; here. Also, interrupts are enabled here and run through the end
; of POST. If your POST task requires interrupts to be off, please
; preserve them by doing a PUSHF, CLI at the beginning and a POPF at
; the end. If you change the PIC, please preserve existing bits.
; Display the copyright notice
; Display the CPU type
; Initialize EISA bus
POST BIOS C-3
; Display prompt "Press F2 to enter SETUP"
;----------------------------------------------------------------------------
04BH quiet Boot Start, OPTIONAL, FAR
04EH post Copyright Display, FAR
050H cpu Display, FAR
051H eisa Init, OPTIONAL
05AH post Display F2 Message, FAR
;----------------------------------------------------------------------------
; Disable the CPU cache
; Size and test the system memory
; Size and test the extended memory
; Test extended memory address lines
; User hook # 1
;----------------------------------------------------------------------------
05BH cpu Cache Off
05CH post Memory Test, FAR
060H post Extended Memory Test, FAR
062H post Extended Address Test, FAR
064H user Patch1
;----------------------------------------------------------------------------
; Enable and configure the cache
; Display the cache size if a cache was detected and enabled.
; Display size of shadow RAM, size of non-disposable BIOS
;----------------------------------------------------------------------------
066H cache Adv Config
068H cache Configure
06AH post Display Cache Size, FAR
06CH post Display Shadows, FAR
06EH post Display Non Disposable, FAR
;----------------------------------------------------------------------------
; Display any POST errors
; Check for configuration errors
; Test Real Time Clock
; Check for keyboard errors
;----------------------------------------------------------------------------
070H post Display Error Messages, FAR
072H post Test Config, FAR
074H post RTC Test, FAR
;----------------------------------------------------------------------------
; Set up hardware interrupt vectors
; Test coprocessor if present
; Return to standard real mode
;----------------------------------------------------------------------------
07CH post Setup Hardware Vectors, FAR
07EH cpu Coprocessor Test, FAR
096H post Clear Huge ES
;----------------------------------------------------------------------------
; Disable programmable I/O devices
; Detect and install fixed RS232 ports
; Detect and install fixed parallel ports
; Init PC-compatible PNP & PCI devices (COM, LPT, floppy, etc.)
; Re-enable programmable I/O and check for conflicts with fixed I/O
;----------------------------------------------------------------------------
post Shutdown Eight Table LABEL post Proc
C-4 POST BIOS
094H post Disable A20, FAR
080H io Before Init, OPTIONAL
085H pci Init Pcc, OPTIONAL
082H io RS232 Test Code
084H io Parallel Test Code
086H io After Init
;----------------------------------------------------------------------------
; Initialize Bios Data Area and Extended Bios Data Area
; Initialize hard and floppy disk controllers
; Initialize MP Environment
;----------------------------------------------------------------------------
088H post Bios Init, FAR
08CH post Floppy Test, FAR
090H fdisk Post Test, FAR
08AH post Init Ext BDAJ, FAR
08BH feat Mouse Test, OPTIONAL, FAR
095H hdd CD Test, OPTIONAL, FAR
093H mp Init, OPTIONAL
092H user Patch2
;----------------------------------------------------------------------------
; Scan for BIOS ROM extensions
;----------------------------------------------------------------------------
098H pci Rom Area Check
;----------------------------------------------------------------------------
; Set up Power Management
; Enable hardware interrupts
; Set time
; Check for key lock
; Init typematic rate
;----------------------------------------------------------------------------
09CH pm Setup, OPTIONAL
09EH post Enable IRQs, FAR
0A0H post Set Time Of Day, FAR
0A2H post Key Lock Test, FAR
0A4H feat Init Keyboard Rate, OPTIONAL, FAR
;----------------------------------------------------------------------------
; Erase F2 prompt
; Check to see if F2 key was pressed
; Optionally print "Press F1 or F2" prompt, and/or enter SETUP
;----------------------------------------------------------------------------
0A8H post Erase F2 Msg, FAR
0AAH post Scan For F2, FAR
0ACH post Setup Check, FAR
;----------------------------------------------------------------------------
; Clear the In Post flag
; Check for errors
; Prepare to boot
; Beep once
; Optionally check password
;----------------------------------------------------------------------------
0AEH post Clear Boot Flag, FAR
POST BIOS C-5
0B0H post Error Check, FAR
0B2H post Done, FAR
0B4H post One Beep, FAR
0B5H quiet Boot End, OPTIONAL, FAR
0B6H feat Check Password, OPTIONAL, FAR
;----------------------------------------------------------------------------
; Shutdown 4 is a boot retry
;----------------------------------------------------------------------------
post Shutdown Four TableLABELpost Proc
;----------------------------------------------------------------------------
;Clear parity checkers
;Optionally clear the screen
;Optionally display any reminder messages
;Try to boot via INT 19
;----------------------------------------------------------------------------
0BCH post Clear Parity, FAR
0BAH post DMI Config, OPTIONAL, FAR
0BDH feat Boot Menu, OPTIONAL, FAR
0BBH pnp Oprom InitBCVs, OPTIONAL, FAR
0BEH post Clear Screen, FAR
0BFH post Check Reminders, OPTIONAL, FAR
08FH fdisk Pre Fast Init, OPTIONAL
091H fdisk Fast Init, OPTIONAL
09FH fdisk Rest Fast Init, OPTIONAL
097H post Mp Fix Up Table, OPTIONAL
0C0H postInt19
postSegment ENDS