Professional Documents
Culture Documents
Is Iso 7452 2002
Is Iso 7452 2002
Is Iso 7452 2002
Whereas the Parliament of India has set out to provide a practical regime of right to
information for citizens to secure access to information under the control of public authorities,
in order to promote transparency and accountability in the working of every public authority,
and whereas the attached publication of the Bureau of Indian Standards is of particular interest
to the public, particularly disadvantaged communities and those engaged in the pursuit of
education and knowledge, the attached public safety standard is made available to promote the
timely dissemination of this information in an accurate manner to the public.
!"#$%&# '(%)
!"# $ %& #' (")* &" +#,-.
Satyanarayan Gangaram Pitroda
Invent a New India Using Knowledge
/0)"1 &2 324 #' 5 *)6
Jawaharlal Nehru
Step Out From the Old to the New
7"#1 &" 8+9&"), 7:1 &" 8+9&")
Mazdoor Kisan Shakti Sangathan
The Right to Information, The Right to Live
!"# %& ;<" =7"#" > 72 &(: ?0)"@" #AB 7" <&*" A*
Bhart+hariN,ti-atakam
Knowledge is such a treasure which cannot be stolen
IS/ISO 7452 (2002): Hot-Rolled structural steel plates -
tolerances on dimensions and shape [MTD 4: Wrought Steel
Products]
ISIISO 7452 : 2002
~ ~ ~ ~ f i ~
\3WWf ~ \3W.hR %g ~
Indian Standard
HOT-ROLLED STRUCTURAL STEEL PLATES -
TOLERANCES ON DIMENSIONS AND SHAPE
ICS 77.140.01; 77.140.50
SIS 2009
BUREAU OF INDIAN STANDARDS
MANAK SHAVAN. 9 SAHADUR SHAH ZAFAR MARG
NEWDELHI 110002
March 2009
Price Group 7
Wrought Steel Products Sectional Committee, MTD 4
NATIONALFOREWORD
This Indian Standard which is identical with ISO 7452: 2002 'Hot-rolled structural steel plates - Tolerances
on dimensions and shape' issued by the International Organization for Standardization (ISO) was adoptedby
the Bureau of Indian Standards on the recommendation of the Wrought Steel Products Sectional Committee
and approval of the Metallurgical Engineering Division Council.
This standard has been-taken up to align it with ISO 7452 : 2002 by adoption under dual numbering system.
The text of the ISO Standard has been approved as suitable for publication as an Indian Standard without
deviations. Certain conventions are, however, not identical to those used in Indian Standards. Attention is
particularly drawn to the following:
a) Wherever the words 'International Standard' appear referring to this standard, they should be readas
'Indian Standard'.
b) Comma (,) has been used as a decimal marker in the International Standard while in IndianStandards,
the current practice is to use a point (.) as the decimal marker.
In reporting the results of a test or analysis made in accordance with this standard. if the final value,
observed or calculated, is to be rounded off, it shall be done in accordance with IS 2 : 1960 'Rules for
rounding off numerical values (revised)'.
15IISO 7452: 2002
Indian Standard
HOT-ROLLED STRUCTURAL STEEL PLATES -
TOLERANCES ON DIMENSIONS AND SHAPE
1 Scope
. This Intemational Standard specifies requirements for tolerances for hot-rolled steel plates made on a reversing mill
(excluding stainless steels) with the following characteristics:
\
' a) nominal thickness a 4 mm but 400 mm;
! b) nominal width > 600 mm;
c) specified minimum yield strength 700 N/mm
2
.
, Tolerances for products of width < 600 mm, cut or slit from plate, should be agreed between manufacturer and
, purchaser at the time of inquiry and order.
Tolerances on dimensions and shape of steel plates having a specified minimum yield stress greater than
700 N/mm
2
should be the subject of agreement at the time of inquiry and order.
This International Standard does not include continuous mill products, custom-made plate, checker plate or bulb
, plate for flooring or wide flats.
It does not apply to continuous hot-rolled steel plates as defined in specific International Standards (see ISO 4995,
! ISO 4996, ISO 5951, ISO 5952).
: 2 Information to be supplied by the purchaser
2.1 General
, The following information shall be supplied by the purchaser at the time of inquiry and order,
a) description of this product (plate);
b) number of this Intemational Standard, i.e, ISO 7452;
c) nominal thickness, in millimetres;
d) the thickness tolerance table and class required (Table 1 class N; Table 2 class A, B, or C) (see 3.2 and 4.1.1);
. e) nominal width, in millimetres (see 4.2.1);
!
I
"f) the letters NKif plate with mill edges is required (see 4.2.2);
;
I (Option 1, see clause 9.)
g) the flatness tolerance required (Table 5,6, 7 or 8);
1 .
ISIISO 7452: 2002
h) nominal length. in millimetres (see 4.3);
i) the letter G if plate with limited edge camber and out-of-squareness is required (see 5.1);
(Option 2, see clause 9.)
2.2 Options
A number of options are specified in clause 9. In the event that the purchaser does not indicate his wish to
implement any of these options, the supplier shall supply the goods in accordance with the basic specification
(see 3.2).
3 Form of supply
3.1 Plate shall be supplied:
with thickness tolerances of Table 1 (class N) or Table 2 (class A, B or C) (see 4.1.1);
with trimmed edges or with mill edges (NK) (see 4.2.2).
3.2 In the absence of information in the order or of code letters for the supply, plate shall be supplied as follows:
sheared or flame cut edges;
normal thickness tolerances, class N (see Table 1);
edge camber and out-of-squareness in accordance with 5.1;
normal flatness tolerances (see Table 5).
4 Tolerances on dimensions
4.1 Thickness
4.1.1 Tolerances on thickness are given in Table 1.
When the purchaser requires another distribution of tolerances (Table 2), the purchaser shall indicate if class A. B
or C is required (see 2.1).
class A: for minus thickness tolerances depending on the nominal thickness;
class B: for a fixed minus tolerance of 0,3 mm;
class C: for all plus tolerances depending on me nominal thickness.
4.1.2 The special provision applicable to ground parts of the surtace of the plates are given in the Intemational
Standards for the corresponding products.
2
I5nSO 7452: 2002
Table 1 - Range of tolerances on thickness (class N)
Dimensions in millimetres
Nominal width, w
Nominal thickness
w<2oo0
t
lower upper lower upper lower upper
4,00 t < 5,00 -0,60 + 0.60 -0.65 + 0,65 - -
5,00 t < 8,00 - 0,60 + 0,60 - 0,75 + 0,75 - -
8,00 t < 15,0 -0.65 +0.65 -0,80 + 0,80 -0.90 + 0.90
15,0 t < 25.0 -0.75 + 0,75 -0.95 + 0,95 - 1.10 + 1,10
25,0 t < 40,0 -0,80 + 0.80 -1,00 + 1,00 -1,20 + 1,20
40,0 t < 80.0 -1,00 + 1.00 -1,20 + 1,20 -1,40 + 1,40
80,0 t < 150 -1,40 + 1,40 -1,60 + 1,60 -1,80 + 1,80
150 t < 250 -1,80 .; 1.80 - + 1,95 - 2.10 + 2,10
.- 2.00 + 2,00 -2.20 + 2.20 -2.40 + 2,40
NOTE 1 For heavier plate thicknesses mm) for special applicat ions, an increased plus (+) tolerance may be permitted
by agreement between the purchaser and the manufadurer.
NOTE 2 By agreement at the time of enquiry and order. and additionally to the N tolerances. a maximum thickness
difference within any plate may be applied , see annex A.
3
...
Table 2 - Classes of distribution of tolerances on thickness
CJ)
o
Ul
N
N
o
:a
Dimensions In rnillimetres
Nominal width, II
II' 4000
I
,---t
Class A Class B L Class C
lower I upper I low0pper lower
Class B
lower I upper
2000,,"<4000
Class A
lower I upper
Class C
lower I upper
Class B
11' < 2 000
lower I upper lower I upper
Class A
Nominal
thickn...
4,00 '" 1<5,00 - 0,40 1+ 0,80 - 0,30 I + 0,90 1+1.20 - 0,45 I + 0,85 0,30 I 1,00