Professional Documents
Culture Documents
Power Electronics Assignment
Power Electronics Assignment
Power Electronics Assignment
15975669
Ubayeda Shaqer
15975669
Page 1 of 15
Ubayeda Shaqer
15975669
Table of Contents
Solution: .................................................................................................................................................. 3
Assumptions:....................................................................................................................................... 3
Part A: ..................................................................................................................................................... 4
a)
b)
c)
d)
e)
f)
g)
h)
Capacitance: ................................................................................................................................ 8
Part B....................................................................................................................................................... 9
Simulation of part A: ........................................................................................................................... 9
Schematic A:.................................................................................................................................... 9
Vthyristor, Ithyristor,Vouput Vs Time: ............................................................................................ 9
Simulation RMS Values: ................................................................................................................ 10
Simulation of part C: ......................................................................................................................... 11
Schematic C: .................................................................................................................................. 11
Vthyristor, Ithyristor,Vouput Vs Time: .......................................................................................... 11
Simulation RMS Values: ................................................................................................................ 12
Simulation of part E: ......................................................................................................................... 13
Schematic E: .................................................................................................................................. 13
Voltage Output Vs Input ............................................................................................................... 13
Simulation of part H: ......................................................................................................................... 14
Schematic H: ................................................................................................................................. 14
Voltage Output:............................................................................................................................. 14
Discussion.............................................................................................................................................. 15
Page 2 of 15
Ubayeda Shaqer
15975669
Solution:
Assumptions:
1. No free-wheeling diode and constant current output; therefore the thyristors conducts
until the next thyristor is switched on.
2. I (holding) is considered zero for the thyristors.
3. Load current is constant at 10 Amps.
4. Motor operates on 100 Volts DC.
5. Input voltage is assumed to be:
6. In the three phase system calculations line to line voltage have been used.
7.
8. 400 is the RMS line to line voltage.
Page 3 of 15
Ubayeda Shaqer
15975669
Part A:
a) Designing a single phase full wave converter:
(
The constant current which is also the maximum current, average current and IRMS:
Firing Angle:
Page 4 of 15
Ubayeda Shaqer
15975669
Thyristor Currents:
ID RMS:
ID Max:
Rectification Efficiency:
Circuit Design:
Page 5 of 15
Ubayeda Shaqer
15975669
The constant current which is also the maximum current, average current and IRMS:
Or
Page 6 of 15
Ubayeda Shaqer
15975669
Thyristor Currents:
ID RMS:
ID Max:
Rectification Efficiency:
Page 7 of 15
Ubayeda Shaqer
15975669
g) Duty ratio:
h) Capacitance:
Equating Capacitance:
Page 8 of 15
Ubayeda Shaqer
15975669
Part B
Simulation of part A:
Schematic A:
Page 9 of 15
Ubayeda Shaqer
15975669
Calculated
286.202 Volts
286.34 Volts
326.6 Volts
326.6 Volts
I(Thyristor Max)
10 Amps
10 Amps
Page 10 of 15
Ubayeda Shaqer
15975669
Simulation of part C:
Schematic C:
Page 11 of 15
Ubayeda Shaqer
15975669
Calculated
555 Volts
555.6 Volts
565 Volts
565.5 Volts
I(Thyristor Max)
10 Amps
10 Amps
I(Thyristor RMS)
I(Output RMS)
V(Output RMS)
Page 12 of 15
Ubayeda Shaqer
15975669
Simulation of part E:
Schematic E:
Figure 3: Circuit Design of Single Phase Full Wave Rectifier with Diodes
Page 13 of 15
Ubayeda Shaqer
15975669
Simulation of part H:
Schematic H:
Voltage Output:
Page 14 of 15
Ubayeda Shaqer
15975669
Discussion
Small inconsistencies between the simulated and calculated values are because of rounding
up numbers to two decimal points. In the case of the simulated results the PSIM software
has a much higher precision level therefore its values are much more accurate.
Page 15 of 15