Professional Documents
Culture Documents
Survival Sewing PDF
Survival Sewing PDF
com
http://wildernessarena.com/skills/general-repair/survival-sewing
Survival Sewing
bhaddock
June 6,
2012
Possessing the knowledge and ability to sew is an essential toolset if you are to survive in the wild for any extended
period of time. Clothing, shelter, shoes, and tools may need to be repaired and often those repairs require basic
sewing technique.
Types of Stitches
Running Stitch The needle is passed alternately up and down through the fabric with each pass moving a few
threads distance. The shorter the distance between the stitches the stronger the seam will be.
Zigzag stitch This is a back and forth stitch that is useful for
reinforcing buttonholes, stitching flexible fabrics, temporarily joining two
fabrics, or to fasten down the trimmed edge of fabric to keep it from
unraveling. Moving from right to left, move diagonally to the left taking a
small stitch, then move diagonally to the right with another small stitch.
Blind Stitch This stitch is ideal for sewing along folds of fabric as it creates a nearly invisible hem because only the
zigzags (which are separated by several straight stitches) penetrate to the visible side of the material. Start by pulling
the needle through the edge of the folded fabric so that the knot is inside the fold and near the crease. Move over only
a couple of threads and push the needle back inside the fold. Run the needle along the fold (on the inside) for about
six threads and then repeat the pattern.
Sewing a knot - Take a tiny stitch through the surface of the fabric about 1/8 of an
inch away from your last stitch. Pull the needle and thread through, leaving a small
loop. Turn the needle around and pass it through the loop, pulling snugly. Clip the
thread.
Basic Repairs
Stitching up a Seam
First, identify whether you are repairing a regular seam or a flat-felled seam. A flat-felled seam is one where the edges
have been rolled under each other to cover the raw edges. Flat-felled seams more common in garments that get
washed frequently (such as shirts).
Regular Seam
Step 1 Pull the edges of the garment flat, matching the raw seam edges to each other. Starting at a point where
the stitching is still solid (slightly before the beginning of the tear), take back stitches along the seam line. You should
be able to follow the pricks and the fold of the earlier stitching; if not, eyeball it so that youre going in a straight line.
Step 2 Continue the stitching until you are slightly past the point where the stitching is missing; for the last section,
be sure to keep to the existing stitching line.
Step 3 When you have finished the stitching, secure your thread by sewing a knot.
Intact Flat-Felled Seam
If the actual seam is intact (you cant poke your finger through the hole), youll just need to stitch down the folds.
Step 1 Tuck the seam extensions securely into their pre-existing folds this is usually just a matter of tucking the
folds that are already there a little more tightly. If you are working with natural fibers, you probably will not need pins
to hold the folds in the fabric. Pinch them down with your fingers; dampening your fingers will help hold the creases
even better.
Step 2 Starting at a point where the stitching is still solid (slightly before the beginning of the tear), whip stitch along
the seam line.
Step 3 Continue stitching until you are past the point where the felling is loose, and secure your thread by sewing a
knot.
Not Intact Flat-Felled Seam
Step 1 Fold the seam allowance to one side. If one side is narrower than the other, fold them so that the narrow one
is under the wider one. If theyre the same width, fold them towards the ridge formed by the existing portions of the
seam. If there are creases in the seam allowance from its former folds, they should stick up.
Step 2 Fold the upper seam allowance around the lower one (if the lower one is narrower) or, if theyre the same
width, fold both seam allowances under.
Step 3 Proceed as directed for repairing the folds of a flat-felled seam.
Repairing a Hem
Hems involve a double fold to protect the raw edge of the fabric; repairing a hem is very similar to repairing the fold of
a flat-felled seam as described above.
Step 1 Fold the hem into place, following the creases that probably exist in the garment. If its gone so long
between repairs that you can no longer find the creases, eyeball the folds based on the edges next to the missing
stitches. Again, natural fibers hold a crease very well. Pinch the folds well with your fingers and you should be able to
continue without using pins.
Step 2 Starting at a point where the stitching is still solid, blind stitch or whip stitch along the fold just catching a
thread or two of the garment fabric.
Step 3 Continue stitching until you are slightly past the point where the hem is torn, and secure your thread by
sewing a knot.
Reattaching a Button
First, determine what kind of button youre replacing. In general, you will be dealing with a shank button (like a uniform
button or a thread button, with a loop underneath it) or sometimes a flat button (two or four holes in the button, no
loop). Next, look to see if your garment has a button stand. In general, you will find one on a woolen garment (coat,
waistcoat, breeches). This is a strip of linen that is sewn along the long edges below where the buttons are attached.
When you are replacing a button, you need to be sure to stitch into this strip, otherwise your button will be prone to
ripping off again.
Shank Button
Step 1 Wax your sewing thread by passing it several times over a chunk of beeswax, and thread your needle with a
double thickness.
Step 2 Take several stiches through the loop and cloth, making sure to catch through to the button stand, which will
keep the buttons from tearing the cloth.
Step 3 Draw the thread to the inside and take a couple of stitches to finish.
Flat Button
Step 1 Wax your sewing thread by passing it several times over a chunk of beeswax, and thread your needle with a
double thickness.
Step 2 Place the needle into the fabric, starting at the back side of the garment, bringing it up through the garment.
Step 3 Make two or three stitches in the fabric where the button will be placed, without the button, to anchor your
thread.
Step 4 Place the button over the anchor stitches and bring the needle up through the button.
Step 5 Lay a straight pin or another needle over the button, between the pair(s) of holes.
Bring your needle down through the button and fabric, allowing the thread to trap the pin.
Repeat two or three times. If you have a 4-hole button, do one pair of holes first, then repeat these steps with the
second pair of holes.
Step 6 When you have taken two or three stitches through each pair of holes, remove the straight pin.
Step 7 Bring the needle up through the fabric and wrap it around the threads a couple of times just underneath the
button to form a thread shank.
Step 8 Bring the needle back to the underside of the fabric and take a couple of stitches to finish.
Darning
First, find thread or yarn that matches the fabric in color, fiber content, and texture; you can use linen or cotton thread
for most applications, while wool yarn is best for wool stockings. Choose a darning needle look for a large eye. A
tapestry needle may also be used for stockings, although it wont work as well for other garments.
Darns go on the wrong side of the garment; if youre darning a stocking, turn it inside-out.
If darning a stocking, place a darning egg inside it and position the hole over the egg. Your needle will glide smoothly
over the eggs surface, making your stitching go faster. If there is no darning egg available, any hard rounded object
(such as a smooth rock) will work. If darning a flat garment, work against a table or other hard flat surface.
Thread the needle with the yarn or thread and leave the end unknotted. The darning process should create a tight
weave that makes knots unnecessary.
Step 1 Start your work on either side of the hole. Take several small vertical running stitches in the intact fabric of
the garment, about 1/2 inch to the left or right of the hole. Turn the garment upside down and make another row of
stitches next to the first. Keep your stitches even try to pick up a single thread per stitch, if possible. This will make
the darn sturdier and more even.
Step 2 When you reach the point at which the hole begins, your stitching line should extend from 1/2 inch above the
hole to 1/2 inch below it. Think of drawing a rectangle around the hole with your darn, and keep the sides of the
rectangle relatively equidistant from it.
Step 3 Continue making vertical running stitches. When your stitching reaches the hole, take your thread or yarn
over the hole and into the fabric on the other side, forming what resembles a vertical bridge over the hole. Stitching
should extend 1/2 inch beyond the hole at both the top and bottom edges.
Step 4 Once you have covered the hole with vertical threads and extended the stitching 1/2 inch past it so that both
sides of the hole look identical, take a tiny stitch across the corner of the rectangle of stitches you have just created.
Step 5 Take the threaded needle and weave it under and over the vertical threads that cover the hole (as well as
the vertical threads that lie within 1/2 inch of the hole).
Step 6 Turn the garment upside down once you reach the opposite end of the hole, and weave another thread next
to the first, making sure you go under the threads you formerly went over, and vice-versa. You are, in effect, reweaving the fabric that is missing. Make these rows very tight together use your fingers to pack them closely, if
necessary.
Step 7 Continue stitching back and forth until youve completely filled the hole. Trim excess thread. No knots are
necessary if you work the stitching correctly.
Patching
Patches are applied to the inside of the garment. Ideally a patch will very closely match the garment; the goal is for
the patch to be as unobtrusive as possible.
Step 1 Cut a patch that is sufficiently large to extend beyond the damage and permit it to be sewn to sound cloth.
Step 2 Fold under the cut edges of the patch and pin it to the inside of the garment, allowing it to overlap beyond the
edges of the damage.
Step 3 Stitch down the patch with a whip stitch or blind stitch.
Step 4 Turn the garment to the outside and secure the edges of the damage to the patch with a zigzag stitch.
If you prefer, you may cut back the damaged area close to the edges of the patch, turn the edges under, and whip
stitch them to the patch. This finish gives the appearance of a flat-felled seam.