Professional Documents
Culture Documents
Installation Instructions For:: Crank Angle Sensor Replacement For EMS P/N 30-6600
Installation Instructions For:: Crank Angle Sensor Replacement For EMS P/N 30-6600
Installation Instructions For:: Crank Angle Sensor Replacement For EMS P/N 30-6600
WARNING:
This installation is not for the tuning novice nor the PC illiterate!
Use this system with EXTREME caution! The AEM EMS System
allows for total flexibility in engine tuning. Misuse of this
product can destroy your engine! If you are not well versed in
engine dynamics and the tuning of management systems or are
not PC literate, please do not attempt the installation. Refer the
installation to a AEM trained tuning shop or call 800-423-0046
for technical assistance. You should also visit the AEM EMS
Tech Forum at http://www.aempower.com
NOTE: AEM holds no responsibility for any engine damage that
results from the misuse of this product!
This product is legal in California for racing vehicles only and should never
be used on public highways.
Page 1 of 9
Page 2 of 9
Figure 2 shows the location of the CAS sensor (inside the distributor assembly).
Page 3 of 9
Remove the back part of the outer plastic cover on the distributor and remove the
distributor cap as shown in figure 4.
Page 4 of 9
Remove the distributor rotor with carefully with the pry bar as shown in figure 5, taking
note of how the rotor was oriented on the shaft. (The photo shows a different distributor
that has the same type of rotor installation)
Page 5 of 9
Remove the internal CAS disc cover shown in figure 7 with a #2 Phillips screwdriver.
Remove the screw holding the CAS disc and collar as shown in figure 8 with the #2
Phillips screwdriver (Make sure screwdriver is firmly planted since this screw will be very
tight).
Page 6 of 9
Figure 9 shows the original CAS disc with the collar that holds it in place removed. The
original disc can be removed now. For future use, the original disc should be marked UP
to remember what the original orientation of the disc is.
The new AEM trigger disc is installed as shown in figure 10, orientation up or down is not
important, only the D-shaped mounting on the shaft.
Page 7 of 9
The internal CAS disc cover can be reinstalled with two screws that held it in place as
shown in figure 12.
Page 8 of 9
Page 9 of 9
WARNING:
This installation is not for the tuning novice nor the PC illiterate!
Use this system with EXTREME caution! The AEM EMS System
allows for total flexibility in engine tuning. Misuse of this
product can destroy your engine! If you are not well versed in
engine dynamics and the tuning of management systems or are
not PC literate, please do not attempt the installation. Refer the
installation to a AEM trained tuning shop or call 800-423-0046
for technical assistance. You should also visit the AEM EMS
Tech Forum at http://www.aempower.com
NOTE: AEM holds no responsibility for any engine damage that
results from the misuse of this product!
This product is legal in California for racing vehicles only and should never
be used on public highways.
Page 1 of 9
,!
WARNING:
This installation is not for the tuning novice nor the PC illiterate!
Use this system with EXTREME caution! The AEM EMS System
allows for total flexibility in engine tuning. Misuse of this
product can destroy your engine! If you are not well versed in
engine dynamics and the tuning of management systems or are
not PC literate, please do not attempt the installation. Refer the
installation to a AEM trained tuning shop or call 800-423-0046
for technical assistance. You should also visit the AEM EMS
Tech Forum at http://www.aempower.com
NOTE: AEM holds no responsibility for any engine damage that
results from the misuse of this product!
This product is legal in California for racing vehicles only and should never
be used on public highways.
Remove the distributor rotor with carefully with the pry bar as shown in figure 2, taking
note of how the rotor was oriented on the shaft.
Remove the internal cover over the CAS disc as shown in figure 3.
Remove the screw holding the CAS disc and collar as shown in figure 4 with the #2
Phillips screwdriver (Make sure screwdriver is firmly planted since this screw will be very
tight).
When collar and screw are removed, the assembly will look like figure 5.
Install the AEM CAS disc as shown below in figure 6, with the D-shaped shaft aligned as
shown.
Reinstall the screw that holds the CAS disc with some red threadlocker with the #2 Phillips
screwdriver as shown in figure 7.
Figure 7: Screw and collar to hold CAS reinstalled with red threadlocker