Professional Documents
Culture Documents
Test 924G, Hydraulic System Pressure - Release
Test 924G, Hydraulic System Pressure - Release
Test 924G, Hydraulic System Pressure - Release
Pgina 1 de 3
Cerrar SIS
Pantalla anterior
Producto: WHEEL LOADER
Modelo: 924G WHEEL LOADER 3PZ
Configuracin: 924G 924Gz Wheel Loader 3PZ00001-UP (MACHINE)
POWERED BY 3056 Engine
Pruebas y Ajustes
Part Number
Description
8T-0856
177-7860
Hose Assembly
6V-4143
Coupler Assembly
6V-3989
Nipple
NOTICE
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 09/09/2011
924G 924Gz Wheel Loader 3PZ00001-UP (MACHINE) POWERED BY 3056 Eng... Pgina 2 de 3
Illustration 1
g00623972
Illustration 2
Pressure reducing valve
g00623709
(1) Test port for the pilot oil pressure in the pressure reducing valve. (2) Test port for the steering pressure in the
pressure reducing valve. (3) Relief valve.
1. Install a 8T-0856 Pressure Gauge on a 177-7860 Hose Assembly . Install the other end of the
hose to the test port (2) for the steering pressure in the pressure reducing valve.
Note: Prior to testing the pilot system pressure, make sure that the standby pressure of the
steering pump is within the specification. The maximum standby pressure of the steering pump
is 4300 170 kPa (625 25 psi).
2. Install a 8T-0856 Pressure Gauge on a 177-7860 Hose Assembly .
3. Install the other end of the hose assembly on the test port for the pilot pressure (1) .
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 09/09/2011
924G 924Gz Wheel Loader 3PZ00001-UP (MACHINE) POWERED BY 3056 Eng... Pgina 3 de 3
4. Start the engine and run the engine at high idle. With the oil at normal operating temperature,
the pressure reading must be 2600 170 kPa (375.0 25.0 psi).
5. If the pressure reading is correct, stop the engine and remove the test equipment from pressure
tap (1) .
If the pressure reading is not correct, stop the engine. Perform the following procedure:
a. Loosen the locknut on the relief valve (3) . Turn the stem on the relief valve clockwise
in order to increase the pressure. Turn the stem on the relief valve counterclockwise in
order to decrease the pressure.
6. If the pressure reading is correct, stop the engine and remove the test equipment from the
pressure tap (1) .
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 09/09/2011
924G 924Gz Wheel Loader 3PZ00001-UP (MACHINE) POWERED BY 3056 Eng... Pgina 1 de 2
Cerrar SIS
Pantalla anterior
Producto: WHEEL LOADER
Modelo: 924G WHEEL LOADER 3PZ
Configuracin: 924G 924Gz Wheel Loader 3PZ00001-UP (MACHINE)
POWERED BY 3056 Engine
Pruebas y Ajustes
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 09/09/2011
924G 924Gz Wheel Loader 3PZ00001-UP (MACHINE) POWERED BY 3056 Eng... Pgina 2 de 2
3. Move the control levers through the full range of travel. Repeat the movement of the levers
several times in order to discharge the accumulator for the pilot system. This will relieve any
pressure that may be present in the work tool hydraulic system.
4. Depress the brake pedal repeatedly. This will relieve any pressure that may be present in the
brake hydraulic system.
https://sisweb.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 09/09/2011