Professional Documents
Culture Documents
MC34063 STmicro
MC34063 STmicro
MC34063EB, MC34063EC
DC-DC converter control circuits
Datasheet - production data
Description
The MC34063A/E series is a monolithic control
circuit which delivers the main functions for DCDC voltage converting.
DIP-8
SO-8
Features
Output switch current in excess of 1.5 A
2 % reference accuracy
Low quiescent current: 2.5 mA (typ.)
Operating from 3 V to 40 V
Frequency operation to 100 kHz
Active current limiting
SO-8
MC34063ABN
MC34063ABD-TR
MC34063ACN
MC34063ACD-TR
MC34063EBN
MC34063EBD-TR
MC34063ECN
MC34063ECD-TR
April 2013
This is information on a product in full production.
DocID5257 Rev 11
1/23
www.st.com
23
Contents
Contents
1
Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2/23
DocID5257 Rev 11
Diagram
Diagram
Figure 1. Block diagram
DocID5257 Rev 11
3/23
Pin configuration
Pin configuration
Figure 2. Pin connections
4/23
Pin n
Symbol
SWC
Switch collector
SWE
Switch emitter
TC
GND
CII
VCC
Voltage supply
IPK
IPK sense
DRC
Timing capacitor
Ground
DocID5257 Rev 11
Maximum ratings
Maximum ratings
Table 3. Absolute maximum ratings
Symbol
VCC
VIR
Value
Unit
50
-0.3 to 40
VSWC
40
VSWE
40
VCE
40
VDC
40
IDC
100
mA
ISW
Switch current
1.5
PTOT
TJ
TSTG
TOP
Note:
Parameter
for DIP-8
1.25
for SO-8
0.625
for AC and EC
series
150
-40 to 150
0 to 70
for AB series
-40 to 85
for EB series
-40 to 125
Absolute maximum ratings are those values beyond which damage to the device may occur.
Functional operation under these condition is not implied.
Table 4. Thermal data
Symbol
Parameter
RthJA
RthJC
(1)
DIP-8
SO-8
Unit
100
160
C/W
42
20
C/W
1. This value depends from thermal design of PCB on which the device is mounted.
DocID5257 Rev 11
5/23
Electrical characteristics
Electrical characteristics
Refer to the test circuits, VCC = 5 V, TA = TLOW to THIGH, unless otherwise specified. (a)
Table 5. Oscillator
Symbol
Parameter
Test conditions
Min.
Typ.
Max.
Unit
fOSC
Frequency
24
33
42
kHz
ICHG
Charge current
24
33
42
Discharge current
140
200
260
Discharge to charge
current ratio
5.2
6.2
7.5
250
300
350
mV
Min.
Typ.
Max.
Unit
IDISCHG
IDISCHG/ICHG
VIPK(sense)
Parameter
VCE(sat)
1.3
VCE(sat)
Saturation voltage
0.45
0.7
DC current gain
VCE = 40 V
0.01
100
Min.
Typ.
Max.
Unit
TA = 25C
1.225
1.25
1.275
TA = TLOW to THIGH
1.21
hFE
IC(off)
Test conditions
50
120
Table 7. Comparator
Symbol
VTH
Regline
IIB
Parameter
Threshold voltage
Test conditions
V
1.29
VCC = 3 to 40 V
mV
VIN = 0 V
-5
-400
nA
a. TLOW = 0 C, THIGH = 70 C (AC and EC series); TLOW = -40 C, THIGH = 85 C (AB series); TLOW = -40 C,
THIGH = 125 C (EB series)
6/23
DocID5257 Rev 11
Electrical characteristics
ICC
VSTART-UP
Parameter
Supply current
Test conditions
Typ.
Max.
for MC34063A
2.5
for MC34063E
1.5
for MC34063A
TA = 25C
CT = 1 F, PIN 5 = 0 for MC34063E
2.1
VCC = 5 to 40 V
CT = 1 nF
PIN 7 = VCC
VPIN5 >VTH
PIN 2 = GND
Remaining pins
open
Min.
Unit
mA
V
1.5
1. Start-up voltage is the minimum power supply voltage at which the internal oscillator begins to work.
Note:
DocID5257 Rev 11
7/23
8/23
DocID5257 Rev 11
DocID5257 Rev 11
9/23
PIN 1 = VOUT
PIN 2 = GND
PIN 3 = GND
PIN 4 = VIN
Conditions
Value (Typ.)
Unit
Line Regulation
VIN = 8 to 16 V, IO = 175 mA
30
mV
Load Regulation
VIN = 12 V, IO = 75 to 175 mA
10
mV
Output Ripple
VIN = 12 V, IO = 175 mA
300
mV
Efficiency
VIN = 12 V, IO = 175 mA
89
10/23
DocID5257 Rev 11
PIN 1 = VOUT
PIN 2 = GND
PIN 3 = GND
PIN 4 = VIN
Conditions
Value (typ.)
Unit
Line regulation
VIN = 15 to 25 V, IO = 500 mA
mV
Load regulation
VIN = 25 V, IO = 50 to 500 mA
30
mV
Output ripple
VIN = 25 V, IO = 500 mA
100
mV
Efficiency
VIN = 25 V, IO = 500 mA
80
ISC
1.2
DocID5257 Rev 11
11/23
PIN 1 = VOUT
PIN 2 = GND
PIN 3 = GND
PIN 4 = VIN
Conditions
Value (typ.)
Unit
Line regulation
15
mV
Load regulation
VIN = 5 V, IO = 10 to 100 mA
20
mV
Output ripple
VIN = 5 V, IO = 100 mA
230
mV
Efficiency
VIN = 5 V, IO = 100 mA
58
ISC
0.9
12/23
DocID5257 Rev 11
ton/toff
Step-Up
(Discontinuous mode)
Step-Down
(Continuous mode)
Voltage Inverting
(Discontinuous mode)
V OUT + V F V IN min
------------------------------------------------------V IN min V sat
V OUT + V F
----------------------------------------------------------V IN min V sat V OUT
V OUT + V F
------------------------------V IN V sat
1/fmin
1/fmin
1/fmin
4.5x10-5t
on
4.5x10-5t
on
4.5x10-5ton
2Iout(max)[(ton/toff)+1]
2Iout(max)
2Iout(max)[(ton/toff)+1]
RSC
0.3/IPK(switch)
0.3/IPK(switch)
0.3/IPK(switch)
CO
I out t on
------------------------------V ripple p p
I PK switch t on + t off
-----------------------------------------------------8V ripple p p
I out t on
------------------------------V ripple p p
V IN min V sat
-------------------------------------- t on min
I PK switch
V IN min V sat
-------------------------------------- t on min
I PK switch
L(min)
Note:
DocID5257 Rev 11
13/23
14/23
DocID5257 Rev 11
DocID5257 Rev 11
15/23
16/23
DocID5257 Rev 11
DocID5257 Rev 11
17/23
18/23
DocID5257 Rev 11
inch.
Dim.
Min.
A
Typ.
Max.
Min.
3.3
Typ.
Max.
0.130
a1
0.7
1.39
1.65
0.055
0.065
B1
0.91
1.04
0.036
0.041
b
b1
0.028
0.5
0.38
0.020
0.5
0.015
0.020
9.8
0.386
8.8
0.346
2.54
0.100
e3
7.62
0.300
e4
7.62
0.300
7.1
0.280
4.8
0.189
L
Z
3.3
0.44
0.130
1.6
0.017
0.063
P001F
DocID5257 Rev 11
19/23
mm.
Min.
Typ.
inch.
Max.
Min.
Typ.
Max.
1.35
1.75
0.053
0.069
A1
0.10
0.25
0.04
0.010
A2
1.10
1.65
0.043
0.065
0.33
0.51
0.013
0.020
0.19
0.25
0.007
0.010
4.80
5.00
0.189
0.197
3.80
4.00
0.150
0.157
1.27
0.050
5.80
6.20
0.228
0.244
0.25
0.50
0.010
0.020
0.40
1.27
0.016
0.050
k
ddd
8 (max.)
0.1
0.04
0016023/C
20/23
DocID5257 Rev 11
inch.
Dim.
Min.
A
Typ.
Max.
Min.
330
Max.
12.992
12.8
20.2
0.795
60
2.362
13.2
Typ.
0.504
22.4
0.519
0.882
Ao
8.1
8.5
0.319
0.335
Bo
5.5
5.9
0.216
0.232
Ko
2.1
2.3
0.082
0.090
Po
3.9
4.1
0.153
0.161
7.9
8.1
0.311
0.319
DocID5257 Rev 11
21/23
Revision history
Revision history
Table 13. Document revision history
22/23
Date
Revision
Changes
20-Nov-2007
10
Added Table 1.
24-Apr-2013
11
DocID5257 Rev 11
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (ST) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to STs terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN STS TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT AUTHORIZED FOR USE IN WEAPONS. NOR ARE ST PRODUCTS DESIGNED OR AUTHORIZED FOR USE
IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH
PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR
ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED
FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASERS SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN
WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR AUTOMOTIVE,
AUTOMOTIVE SAFETY OR MEDICAL INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS.
PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE
CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
DocID5257 Rev 11
23/23