Professional Documents
Culture Documents
Epc 41 Control Unit
Epc 41 Control Unit
Description
P000681A
EPC-41
Control Unit
Product No.
31830-5086-1
31830-5086-2
31830-5087-1
31830-5087-2
Printed
Book No.
Jun 1997
1818001-02 V2
Alfa Laval reserve the right to make changes at any time without
prior notice.
Any comments regarding possible errors and omissions or
suggestions for improvement of this publication would be
gratefully appreciated.
Copies of this publication can be ordered from your local Alfa
Laval company.
Published by:
Contents
Overview
6.4
Terminal Protectors
19
Function Description
Spare Parts
21
2.1
Application
2.2
Working Principle
2.3
Design
2.3.1
Front Panel
2.3.2
2.3.3
Control Module
2.3.4
Power Supply
Operation
3.1
Process Operation
3.2
Parameter Setting
3.2.1
Overview
3.2.2
Setting Procedure
Maintenance
11
4.1
Preventive Maintenance
11
4.1.1
11
4.2
Corrective Maintenance
4.2.1
4.3
Lamp Test
12
12
Replacement of Control
Module
13
Technical Data
15
5.1
Specification
15
5.2
Dimensions
16
Installation
17
6.1
Mounting
17
6.2
Cable Routing
18
6.3
18
1818001-02 V2
1818001-02 V2
Overview
1818001-02 V2
1 Overview
EPC-41
1818001-02 V2
Function Description
2.1 Application
The EPC-41 control unit is used in clarifier
and purifier separation systems.
1818001-02 V2
2 Function Description
EPC-41
2.3 Design
2.3.1 Front Panel
G001142A
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
1818001-02 V2
EPC-41
2 Function Description
G001162A
1818001-02 V2
P000591A
1. Control module
2. Circuit board
3. Mode switch
4. Display
5. Push buttons (for parameter setting)
6. Push buttons (for parameter selection)
F1F3 Fuses
F11.Main switch/main fuse
X-. Terminals
2 Function Description
EPC-41
P000601A
1.
F11
T1
Z1
XA
1818001-02 V2
Operation
1818001-02 V2
3 Operation
EPC-41
3.2.1 Overview
The method of parameter setting is:
1. Set the mode selector in position P
(programming).
G001391A
1
2.
3.
4.
5.
6.
7.
G001861A
G001881A
1818001-02 V2
EPC-41
3 Operation
Installation Parameters
G001921A
G044781A
G044791A
G044801A
1818001-02 V2
G001891A
3 Operation
EPC-41
G001931A
G001941A
10
1818001-02 V2
Maintenance
4.1 Preventive
Maintenance
It is recommended to carry out a lamp (LED)
test once a month. No other regular
maintenance is required.
1818001-02 V2
11
4 Maintenance
EPC-41
4.2 Corrective
Maintenance
4.2.1 Fuses and Related Functions
P000103A
Functions influenced
Alarm
F1
Remote alarm
Display black (A4 when new fuse installed)
F2
A1-4
A2-6
C/F EEE
F3
All outputs
PS42
Power terminal
Fuse
Functions influenced
Alarm
F12, F13
Display black
12
1818001-02 V2
EPC-41
4 Maintenance
4.3 Replacement of
Control Module
If a persistent fault is found in the control
module it must not be repaired, but must be
replaced and sent to an Alfa Laval
representative for repair.
1. Make a note of all the actual parameter
settings.
2. Switch off the power to the EPC by the
main switch on the starter.
3. Open the panel door.
4. Pull out the wire terminal sockets by hand
G009293A
G009294A
G009295A
1818001-02 V2
13
4 Maintenance
EPC-41
G009296A
14
1818001-02 V2
Technical Data
5.1 Specification
Mains voltage
48 V AC
During separation:
max. 110 VA
During sludge discharge: max. 200 VA
Inrush:
max. 5 x 45 VA
Continuous: max. 5 x 23 VA
Frequency
50/60 Hz 5%
1.5 mm2
Alarm inputs
Communication
Fuses
Weight
18 kg
1818001-02 V2
+10 %
15 %
15
5 Technical Data
EPC-41
Ambient temperature
Max. 55 C
Degree of protection
IP 65
X001531A
5.2 Dimensions
Article No.
Type
Separator type
31830-5086-1
31830-5087-1
EPC-41
MMPX 303/304
31830-5086-2
31830-5087-2
EPC-41
MOPX
16
1818001-02 V2
Installation
NOTE
If the specifications are not followed,
Alfa Laval cannot be held responsible
for any malfunction of the
installation.
6.1 Mounting
Recommendation
The EPC is wall-mounted by means of two
keyhole lugs and two fastening lugs. For hole
dimensions, see dimensioned drawing.
1818001-02 V2
17
6 Installation
EPC-41
Cables that are to be connected to the lefthand terminals must enter from the LEFT.
Cables that are to be connected to the righthand terminals must enter from the RIGHT.
Any other way of routing or mixing cables is
completely unacceptable.
18
1818001-02 V2
EPC-41
6 Installation
G032401A
G032391A
G032411A
1818001-02 V2
19
6 Installation
20
EPC-41
1818001-02 V2
Spare Parts
G005512A
Item
Qty
Article No.
Description
Remarks
31830-5009-2
Control module
1)
4900795-18
Transformer
2148V/102024 V
4900860-26
Circuit breaker
4901008-02
4901156-03
Screw terminal
6:1
6:2
6:3
6:4
1
5
5
5
5
31830-5021-1
4900850-21
4900850-14
4900850-24
4900850-19
1.
2.
1) 2)
2.5A, 5x20
500 mA, 5x20
5 A, 5x20
1.6 A, 5x20
1818001-02 V2
21
7 Spare Parts
22
EPC-41
1818001-02 V2