Professional Documents
Culture Documents
Sa STC MR 2g 3g Lte Mop Ver2 2
Sa STC MR 2g 3g Lte Mop Ver2 2
version 2.0
SA STC, project
Typical O/P
Power per
TRX
No. of antenna
lines per sector
No
Model Configuration
No. of System
Module
4+4+4
20 W
6+6+6
20 W
8+8+8
20 W
12+12+12
15 W
6+6+6/4+4+4
20 W
2/2
6+6+6/6+6+6
20 W
2/2
6+6+6/8+8+8
20 W
2/3
8+8+8/6+6+6
20 W
3/2
8+8+8/8+8+8
20 W
3/3
10
8+8+8/12+12+12
15 W
3/3
11
12+12+12/4+4+4
15 W
3/2
12
12+12+12/8+8+8
15 W
3/3
Pipe 2
Pipe 3
Div Rx
Tx 60W/Rx
Div Rx
Tx 60W/Rx
Div Rx
Tx 60W/Rx
Alternativ
e RRH
site
solution
2G/3G/LTE/LTE-A
Flexi Multiradio
System Module,
2G/3G/LTE/LTE-A
Optional PDU
3G or LTE / BB
extension
Optional transport
interfaces
3G or LTE BB
extension
Alternative
Active
Antenna
site
solution
Alternative
Indoor
System
Module
6+6+6 @ 900MHz
4+4+4 @1800MHz
6 TRXs
(20W)
10W
10W
A
12/12/12 @10w per TRX or
8/8/8@15w per TRX or
6/6/6 @ 20w per TRX or
4/4/4 @ 20w per TRX
2/2/2 @60w per TRX
ESMB=max18TRx.
FXDA-900
FXEA-1800
900
1800
8/8/8 or
8/8/8 or
12/12/12
12/12/12
or more sectors
11
900
12
13
14
15
16
Example
Site: ZMKA007
BSC GK12B3
6+8+6(900) / 4+8+4 (1800)
17
18
19
DTRX
WCDMA
WBC
Diplexer
DTRX
43W
20W
17W
MultiRadio
20W/15W
20
WCDMA
WBC
DTRX
20W
43W
DTRX
WCDMA
WBC
Diplexer
WBC
8.7W
MultiRadio
10W
21
6W
WCDMA
WBC
Diplexer
20W
DTRX
17W
43W
DTRX
43W
WCDMA
WBC
Diplexer
20W
17W
MultiRadio
10W
22
NOTES
The above A-bis mapping is for the standard A-bis configuration which is
appearing most of the time in the network
Any odd configuration to be planned by NPO and shared with the rest of the
team before MDT
23
24
Sector 2
Sector 1
Div Rx Tx/Rx
Div Rx Tx/Rx
Div Rx Tx/Rx
Rx Out
Rx Out
Rx Out
1+1+1/2+2+2
2+2+2/3+3+3/4+4+4
BTS Rx Signal Level must be smaller than -102dBm during
commissioning
26
27
Optical cable
DC cable
28
29
30
31
Power consumptions
32
Clock Synchronization
Timing over packet for 2G BTS (Not Co-located with 3G Node-B)
The RAN synchronization is based on Timing Over Packet following standard IEEE 1588.
One ToP master clock can synchronize up between 800 NE.
The ToP will be connected to CE Router as 1+1 ( Active and Standby ) as shown below.
33
Clock Synchronization
Timing over packet for 2G BTS (Co-located with 3G NodeB)
Synchornization to other system modules can also be done based on IEEE1588-2008, provided other
system modules support IEEE1588-2008 slave functionality. ToP Engineering rule should be taken into
account.
2G/3G Modernization
GSM
1. Existing Dump to be used as a reference
2. Existing Physical site database as a reference
3. 2G Parameter/new frequency plan in case new configuration is needed (for
example TRX upgrade), For 3G Parameter/SC plan in case new configuration is
needed (for example Carrier upgrade)
4. A-bis timeslot mapping generated by the planning team to be followed
5. XML creation to be done in a case the site configuration changed (existing
parameters to be used if no upgrade)
6. the above XML to be sent to CM team for implementation
7. Site integration report received from NI after integration
8. NPO will check the parameter consistencies, health check (alarms), and initial KPI
9. Post modernization Drive test to be done to verify the hardware and swap feeders
35
36
37
3G
38
39