Professional Documents
Culture Documents
Bansal's Wiki - Planning Machine
Bansal's Wiki - Planning Machine
Bansal's Wiki - Planning Machine
Bed:
It is a very large and heavy cast iron structure which is provided with cross ribs for additional
strength and stiffness. In case of large planers the bed is sometimes made in two parts which are
properly machined and then bolted together to form a single length of bed.
Leveling pads or jacks are provided under the bottom of the bed to level it during its installation.
The bed itself accommodates the table driving mechanisms. V-ways and sometimes flat ways are
provided on the top of bed to guide and support the reciprocating table of the planer. These bed
ways are straight and parallel accurately machined and scrapped. The bed ways should be
constantly lubricated.
January (61)
LABELS
3GL (1) 4GL (1) abstract (1) active (2) addition (2)
adhesive
advantages
(1)
disadvantages (6)
and
Table:
The table or platen is also made of cast iron with an accurately machined top. It carries a box
type construction provided with strengthening ribs under it in order to make it strong enough to
support the heavy work over it. At its top it has longitudinal T-slots and holes to accommodate
the clamping bolt and other devices.
Under the table chip pockets are cast integral with it for collecting and removing the chips. On its
side the table carries adjustable stops to reverse its motion at the end of each stroke. A common
safety device i.e. large cutting tool is bolted under the table on its both sides and stops blocks are
fixed on the bed on each side.
In case of running away of the table the tool will take a deep cut into the stop block and thus
absorb the whole kinetic energy of the table, bringing it to a halt without damage to machine or
workman.
(8)
carbon
dioxide
(3)
coding (20)
coke
comparison
(1)
(2)
constants
(1)
constituents
(1)
Cross rail:
It is a horizontal member of heavy structure which connects the two vertical housings of the
machine. It provides additional rigidity to the machine. By means of elevating screws it can be
moved up and down along the guide ways.
Clamps are provided to lock the cross rail in any desired position along the columns. In order that
the cross rail is moved up or down uniformly on both ends, both the elevating screws are rotated
simultaneously by horizontal shaft, mounted on the top of the machine.
Accurately finished ways are provided at the front of the cross rails for the two vertical tool heads.
Inside the rail the feed rods for vertical power feed and cross feed for the tools are provided.
cutting (6)
DC and AC equipment
decision (8)
defects in
drilling (5)
Tool heads:
The planner tool heads resemble with shape tool heads in construction as well as in operation.
bansalwiki.blogspot.in/2013/02/planing-machine.html
(1) fibonacci (1) files (3) filing (1) filler (1) fire (1)
firew all services (1) fitting (3) fitting processes (1)
fixed time slot (1) flatters (1) float (1) floor (1) flow
2/4
1/20/14
Four tool heads can be fitted in a planer and any or all of them can be used at a time. Two tool
heads can be fitted in a vertical position on the cross rails and the other two can be fitted in
horizontal position on the vertical columns.
The tool head on the cross rail can travel horizontally along the cross rail. They can also be raised
or lowered moving the cross rail up and down. The side tools can move up and down along the
vertical column ways. The side tools can be fed horizontally into the job or at a desired
inclination.
Both hand and power feeds can be employed for all the tool heads. The tool head can swivel on
either side from its normal position and the apron can also be set at an inclination whenever
needed in the same way as in shaper head. The clapper block is also hinged in similar way as in
shaper so as to avoid scratching during idle stroke.
(2) flux (1) follow board (1) forge (2) forging (3)
forging operations
(1)
format (47)
foundry
(5)
(19)
(1)
friend
functions
Controls:
Various controls for governing the action of different parts of planer are systematically provided
in the easy reach of the operator. The controls may be provided on a suspended pedant easily
approachable by the operator. A suspended pedant usually has the controls like start, stop,
automatic cut, automatic return etc. The controls are devices for quick adjustments of vertical or
horizontal tool feeds, control for rapid transverse of the tool heads individually or together. These
controls sometimes increases the work efficiency.
(34)
identifiers
language (53)
shearing (2) limit (5) link (1) linking (1) linux (1)
Labels: bed, construction, controls, cross rail, machine, manufacturing, plaining machine, planar type,
liquid (1) loader (1) loam (1) logical (1) logs (1)
(10)
loop
machine (12)
No comments:
(1)
malleability
(1)
manufacturing (30)
marking (6)
Post a Comment
manipulators
(1)
(9)
seasoning
network
Comment as:
Publish
Google Account
(3)
(1)
nested
(5)
non-ferrous
(2)
(1)
normalizing (1)
objects (6)
Preview
method
nibbling
operating (6)
OOPs (21)
operands (1)
operators (19)
on w ood (1)
(6)
output
(2)
oxy-acetylene
optical (1)
OS
w elding
(1)
Home
Older Post
practical (22)
program
programming (47)
(42)
bansalwiki.blogspot.in/2013/02/planing-machine.html
3/4