Professional Documents
Culture Documents
Amphion Operators Guide OMM
Amphion Operators Guide OMM
Amphion Operators Guide OMM
User Manual
FINAL DOCUMENTATION
Customer
Keppel Fels
Rig/Hull
Seadrill B311
Project Manager
Mark West
Sales Order Number
JS8063001
Serial Number
N/A
Project Number
TX6087
Document Number
Rev
D811001248-MAN-001
www.nov.com
01
Amphion
Operators Guide
Standard
Reference
Reference Description
Standard
www.nov.com
Document Number
Rev.
D811001248-MAN-001
01
D811001248-MAN-001
Revision 01
Revision History
01
08.07.2010
First issue
Anthony
Archilla
Paul
Williams
Jeff
Faga
Rev
Date (dd.mm.yyyy)
Prepared
Checked
Approved
Change Description
Revision
01
Change Description
First Issue
www.nov.com
D811001248-MAN-001
Revision 01
Page i of xii
Table of Contents
Chapter 1: General Information
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notes, Cautions, and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Personnel Training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General System Safety Practices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Proper Use of Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOV Service Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
1-1
1-2
1-2
1-2
1-3
1-3
1-3
1-3
1-3
1-4
i
www.nov.com
D811001248-MAN-001
Revision 01
Page ii of xii
Table of Contents
Step 7 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen Communication Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tool Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ownership . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HTTP Requests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Write Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exceptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tool Ownership . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ownership Controls and Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Granting and Releasing Ownership . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tool Controllers and Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RigSense and WITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Simple Data Acquisition (S-DAQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System 5 Data Acquisition (V-DAQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electronic Driller System (EDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-25
2-27
2-28
2-30
2-31
2-32
2-32
2-34
2-34
2-35
2-35
2-36
2-36
2-36
2-36
2-36
3-1
3-3
3-4
3-4
3-6
3-7
3-7
Chapter 4: Assignments
Drawworks/Top Drive Assignments Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drawworks Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Top Drive Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
4-2
4-2
4-2
5-1
5-1
5-2
5-2
5-3
5-3
5-4
5-4
5-5
5-5
5-6
5-7
5-8
ii
www.nov.com
D811001248-MAN-001
Revision 01
Page iii of xii
Table of Contents
Descriptions and Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Pipe Type Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Loading an Existing Setup File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
Editing an Existing Setup File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
Pipe Type Category Edit Pop-Up Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
Calibrate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
CRT Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
Selecting and Loading a Setup File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
Changing Graph Display Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
Y or X Axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
Mark Shoulder Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
Highlight Minimum and Maximum Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18
Zoom (Y or X) In or Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19
Display Data Points (Dots) or Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19
Fill Graph Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19
Turn and Torque Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19
Chapter 6: Cathead
Operator Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tool Ownership . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cathead Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stream Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Slow Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Defining Tong Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Defining Torque Setpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pull Force . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cathead Tool Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-1
6-1
6-1
6-2
6-2
6-3
6-3
6-4
6-4
6-5
iii
www.nov.com
D811001248-MAN-001
Revision 01
Page iv of xii
Table of Contents
Chapter 8: Crown-Mounted Compensator (CMC)
Operator Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tool Ownership . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HP (Hydraulic Pump) Oil System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low Instrument Air Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Position Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Valve Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Valve Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Air Valve Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CMC Pressure Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Position Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compensator Tool Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-1
8-1
8-1
8-2
8-2
8-2
8-2
8-2
8-3
8-3
8-4
8-4
8-5
Chapter 9: Conveyor
Operator Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Tool Ownership . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Status Displays and Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Tool Mode Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Auto Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Slow Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Warm Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Idle Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Belt Controls and Pipe Length Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Pipe Positioner Controls and Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
Pipe Lifter Controls and Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
Conveyor Tool Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12
iv
www.nov.com
D811001248-MAN-001
Revision 01
Page v of xii
Table of Contents
Defining the Drawworks Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Slip & Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lowering and Hoisting Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Autodrill Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating the Electronic Driller System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating or Deactivating Autodrill Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Defining Parameter Setpoint Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Variable Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drilling Trends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Reaming Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drawworks Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor Controls Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auxiliary Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tool Diagnostics Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drum Encoders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enable or Disable an Encoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hook Load Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enable or Disable a Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compensator Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enable or Disable a Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drawworks Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarm and Fault Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarms Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking Brake Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Capacity Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Valve Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Wear Measurement Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drum and Block Status Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor/VFD Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calibration Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Block and Elevator Position Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hook Load Tare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standpipe Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CMC Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarm Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abnormal Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-13
10-13
10-13
10-14
10-17
10-18
10-18
10-19
10-19
10-21
10-22
10-23
10-25
10-26
10-26
10-27
10-28
10-28
10-28
10-28
10-29
10-29
10-29
10-30
10-30
10-30
10-31
10-31
10-31
10-32
10-32
10-32
10-33
10-34
10-35
10-36
10-36
10-38
10-38
10-46
10-47
10-48
10-49
10-49
10-49
10-49
10-49
v
www.nov.com
D811001248-MAN-001
Revision 01
Page vi of xii
Table of Contents
Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Soft Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Category 2 Stops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E-Stop (Category 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-49
10-49
10-50
10-50
13-1
13-1
13-2
13-2
13-3
13-4
14-1
14-2
14-2
14-2
14-2
14-3
14-4
15-5
15-5
15-6
15-6
15-6
15-6
15-7
vi
www.nov.com
D811001248-MAN-001
Revision 01
Page vii of xii
Table of Contents
Mud Pump Status Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Strokes Per Minute (SPM) Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Defining Maximum SPM Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standpipe Pressure Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Defining the Pressure Limit Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting and Pausing Mud Pump Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stop All Mud Pumps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operator Messages and Miscellaneous Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mud Pump Tool Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mud Pump Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auxiliary Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status and Fault Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Motor Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16-2
16-2
16-3
16-3
16-4
16-4
16-5
16-5
16-6
16-7
16-8
16-8
16-9
18-1
18-1
18-2
18-3
18-4
18-5
vii
www.nov.com
D811001248-MAN-001
Revision 01
Page viii of xii
Table of Contents
Power Available Calculations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Total Power Available . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tool Power Available (General) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Limiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19-13
19-13
19-13
19-13
viii
www.nov.com
D811001248-MAN-001
Revision 01
Page ix of xii
Table of Contents
Slew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guide Arm Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Traverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Slew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Shoulder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Telescope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wrist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ATOS Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bridge Racker Trolley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bridge Racker Aft Traverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bridge Racker Hoist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guide Arm Trolley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guide Arm Shoulder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guide Arm Wrist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guide Arm Slew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Guide Arm Telescope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thread Comp Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Axis Position Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20-34
20-35
20-36
20-37
20-38
20-39
20-40
20-41
20-41
20-42
20-43
20-44
20-44
20-45
20-45
20-46
20-47
20-48
ix
www.nov.com
D811001248-MAN-001
Revision 01
Page x of xii
Table of Contents
Operator Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tool Ownership . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Direction Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lock Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speed and Torque Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Defining the Speed Setpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Zero Throttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Defining the Torque Setpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rotary Table Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22-1
22-1
22-2
22-3
22-3
22-4
22-4
22-4
22-4
22-5
22-6
x
www.nov.com
D811001248-MAN-001
Revision 01
Page xi of xii
Table of Contents
Duck Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mud Bucket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bit Breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rotating Tong Open Throat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Travel Well/Foxhole Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23-25
23-25
23-26
23-26
23-27
24-1
24-1
24-2
24-2
24-2
24-3
24-3
24-3
24-5
24-6
24-6
24-6
24-7
24-7
24-7
24-8
xi
www.nov.com
D811001248-MAN-001
Revision 01
Page xii of xii
Table of Contents
Link Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CCW and CW Link Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Link Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mousehole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Top Drive Tool Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor/VFD Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chopper/DBR Status Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TDS Motor/Assigned VFD Status Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor Winding and Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor Winding Temp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor Temp Abort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fault Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auxiliary Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Trends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25-13
25-13
25-13
25-13
25-14
25-15
25-16
25-16
25-16
25-17
25-17
25-17
25-17
25-18
25-18
25-18
25-19
27-1
27-2
27-3
27-4
27-6
27-8
Chapter A: Appendix
Network Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Opening a Command Prompt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Command Descriptions and Syntax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Ping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Ping Command Switch Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
IP Config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
Tracert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3
Nslookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Network Address Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-5
xii
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Chapter 1.0
Amphion Operators Guide
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.1
General Information
www.nov.com
D811001248-MAN-001
Revision 01
Page 1-1 of 4
General Information
Conventions
This manual is intended for use by field engineering, installation, operation, and repair personnel.
Every effort has been made to ensure the accuracy of the information contained herein. National
Oilwell Varco (NOV) will not be held liable for errors in this material, or for consequences arising
from misuse of this material.
!
The caution symbol indicates that potential damage to
equipment or injury to personnel exists. Follow instructions
explicitly. Extreme care should be taken when performing
operations or procedures preceded by this caution symbol.
1-1
www.nov.com
D811001248-MAN-001
Revision 01
Page 1-2 of 4
General Information
Illustrations
Illustrations (figures) provide a graphical representation of equipment components or screen
snapshots for use in identifying parts or establishing nomenclature, and may or may not be drawn
to scale.
For component information specific to your rig configuration, see the technical drawings included
with your NOV documentation.
Safety Requirements
NOV equipment is installed and operated in a controlled drilling rig environment involving
hazardous situations. Proper maintenance is important for safe and reliable operation. Procedures
outlined in NOV manuals are the recommended methods of performing operations and
maintenance.
!
To avoid injury to personnel or equipment damage,
carefully observe requirements outlined in this section.
Personnel Training
All personnel performing installation, operations, repair, or maintenance procedures on the
equipment, or those in the vicinity of the equipment, should be trained on rig safety, tool operation,
and maintenance to ensure their safety.
!
Personnel should wear protective gear during installation,
maintenance, and certain operations.
Contact the NOV Drilling Equipment training department for more information about equipment
operation and maintenance training.
1-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 1-3 of 4
General Information
Recommended Tools
Service operations may require the use of tools designed specifically for the purpose described.
NOV recommends that only those tools specified be used when stated. Ensure that personnel and
equipment safety are not jeopardized when following service procedures or using tools not
specifically recommended by NOV.
!
Read and follow the guidelines below before installing
equipment or performing maintenance to avoid
endangering exposed persons or damaging equipment.
Replacing Components
R
Verify that all components (such as cables, hoses, etc.) are tagged and labeled
during assembly and disassembly of equipment to ensure correct installment.
Routine Maintenance
Equipment must be maintained on a routine basis. See the service manual for maintenance
recommendations.
!
Failure to conduct routine maintenance could result in
equipment damage or injury to personnel.
1-3
www.nov.com
General Information
D811001248-MAN-001
Revision 01
Page 1-4 of 4
1-4
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.2
Amphion Overview
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-1 of 38
Amphion Overview
Integrated operator interface application for National Oilwell Varco (NOV) and thirdparty tools, systems, or processes, such as:
Alarm and Event System
Automated Drawworks System
Automated Roughneck
Bridge Racker and Tailing Arm
Casing Running Tool
Chair (Workstation) Diagnostics
Drawworks VFD Assignment Controls
Driller Auxiliaries
Fingerboard
Foxhole
Hydraulic BX Elevators
Hydraulic Cathead
Hydraulic Power Unit
Mud Pump Motor Assignment Controls
Motor Control Center (MCC)
Mud Pumps
2-1
www.nov.com
Amphion Overview
D811001248-MAN-001
Revision 01
Page 2-2 of 38
Ownership Overview
Pipe Racking System
Power Management System
Power Slips
Rotary Support Table
Silicon-Controlled Rectifiers (SCR)
Simple Data Acquisition (S-DAQ) module
System 5 Data Acquisition (V-DAQ) module
Top Drive System
Top Drive VFD Assignment Controls
Variable Frequency Drive (VFD) System
RigSense application, RigSense server
Zone Management System (ZMS)
R
Engineering drawings
2-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-3 of 38
Amphion Overview
Operator Workstation
The workstations are the user's interface to the control network and tools. A Wrap-Around
workstation is shown here.
Located in the drillers cabin, each workstation may contain:
R
One chair
300
250
350
500 550
400 450
600
650
700
750
200
800
150
850
100
900
50
X 1000 LB
X 1000 LB
1000
Touchscreen Computers
Workstations include self-contained touchscreens that display tool control, drilling operation,
alarm, and status information. The Wrap-Around workstation can accommodate up to four
touchscreens, all with access to tools connected to the network.
2-3
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-4 of 38
Amphion Overview
MUD
PU
THRO MP #1
TTLE
MUD
PU
THRO MP #1
TTLE
MUD
PU
THRO MP #2
TTLE
MUD
PU
THRO MP #2
TTLE
M
U
D
P
U
M
P
S
MUD
PU
THRO MP #3
TTLE
OFF
/AUT
O
TDS
KE
CLO
SE
TDS
DRIL
L
CLO
SE
BRA
TDS
OPE
MUD
PU
THRO MP #3
TTLE
FLO
AT
LINK
OPE
N
POW
ER S
TILT
OPE
N
CLO
SE
ELE
VAT
OR
R AC
ELE
VAT
OR
KER
OFF
/AUT
O
OPE
CLO
SE
RAC
KER
X
OVE /Y
RRID
E
OFF
/AUT
O
DRA
ING
JAW
ON
OVE WORKS
RRID
E
RAC
K
TRA ER
OVE VEL
RRID
E
PAR
K
RAC
KE
JAW R
S
ON
DOL
PAR
K
LINK
CLO
SE
TDS
TDS
TDS
OPE
N
IBOP
LINK
TILT
FLO
AT
CLO
SE
LIPS
DRIL
L
TDS
P
U
M
P
S
ON
OPE
N
TDS
M
U
D
BRA
LY E
NAB
ING
BRA
KE
LE
KE
SLIP
S EN
OVE
ADS
RRID
OPE
N
ABL
E
CLO
SE
IBOP
2-4
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-5 of 38
Amphion Overview
OOR
L FL
DRIL IPMENT
EQU TOP
E-S
H TO
PUS
OOR
L FL
DRIL IPMENT
EQU TOP
E-S
STO
H TO
PUS
STO
TDS
P
RT R
O
AUT
AR - ENCE
U
SEQ
RPM
TDS
AK
MAK
BRE
OUT
IN
DOW
UP
U
ORQ
AR T
PIN
AR S
E
CLO
G
RRIA
W CA
CLO
L
WEL
BAC
SE
SE
N
OPE
EAS
SE
INCR
L
TOO IP
H
ERS
OWN SE ALL
A
RELE
SE/
CLO K
LOC
N/
E
P
O
AUTO
REA
N
OPE
DEC
LOW
LIC F
RAU ALVE
HYD
V
CMC UT OFF
SH
W
AR T
AIR
KING E
WOR
R
CMC PRESSU
APV
AR S
AR
EL
TRAV
SE
C LO
N
OPE
MAIN
CMC VE
VAL
L
TOO IP
H
ERS
OWN SE ALL
A
E
REL
IPS
P/SL
R
BLE
ENA LEVATO
E
BX
PULL
PAY
EAD
CATH
2-5
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-6 of 38
Amphion Overview
Joysticks
Open Slips
Close Slips
Upper
Lower
Lower
Hoist
Dead man
switch
Dead man
switch
Lower
+Y
+X
-X
-Y
Hoist
The joystick mounted on the operator workstations right control panel can control:
R
The drawworks
The racker
The tool or tools that a joystick controls depends upon your particular rig configuration and tool
ownership. Tool ownership logic prevents the operator from taking ownership of both the
drawworks and the racker simultaneously. See section titled "Tool Ownership" on page 2-34.
Using the joystick to move the racker affects its destination, which varies depending on its current
mode (selected via the user interface).
If the joystick does not offer power slip controls, then the workstations control panel normally
contains a discrete switch for opening and closing the slips. This is in addition to touchscreen
controls.
If the joystick has the ability to control both the power slips and the drawworks, the workstations
control panel will not contain controls for opening and closing the power slips. However, the control
2-6
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-7 of 38
Amphion Overview
panel will contain a button that must be pressed in order to enable the power slips and allow the
operator to control the slips by using either the joystick or touchscreen controls.
2-7
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-8 of 38
Amphion Overview
Active tool
2-8
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-9 of 38
Amphion Overview
The tool buttons blink red when there is at least one active and unacknowledged alarm for that
particular tool. The button displays solid red when there is at least one active but already
acknowledged alarm. Otherwise, the button displays solid blue.
Press the red tool button to display alarms associated with that tool. See Chapter 3, titled "Alarms
and Events for more information.
Driller Tools
Current tool ownership status indicators display in the bottom left corner of each tool button (where
applicable). See section titled "Tool Ownership" on page 2-34 for more information.
Press to select a tool and display its default operator screen. See tool-specific chapters in this
manual for more detail.
2-9
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-10 of 38
Amphion Overview
Press the Operator button to display the current tools operator screen.
Back or Forward
Press Back or Forward to toggle between the current screen and the previous screen.
2-10
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-11 of 38
Amphion Overview
Maintenance Mode
Enable maintenance mode to engage tool override for maintenance purposes only.
Controls are disabled at the operator workstation touchscreens when maintenance mode is
enabled.
From the diagnostic workstation (DWS) computer, select one of the following tools:
R
Auxiliary (normally includes the cathead, HPU, power slips, and rotary table)
Conveyor
Racker
Roughneck
Top Drive
Press <This Tool> --> Maintenance Mode to display the Maintenance Mode screen.
Press Active to engage maintenance mode for the appropriate tool controller (also referred to as
an SBC). Press Inactive to disengage maintenance mode.
2-11
www.nov.com
Amphion Overview
D811001248-MAN-001
Revision 01
Page 2-12 of 38
Operator Screens
Many tool screens contain common features shown in this section.
Operator Messages
Most tool screens contain messages for the operator that display along the bottom of the screen.
Keypads
Numeric keypads and alpha-numeric keyboards are pop-up windows that appear when the
operator presses a tools on-screen button, and is normally used to define a specific parameter for
a tool.
2-12
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-13 of 38
Amphion Overview
Utility Menu
Press <This Tool> --> Utility to display the Utility menu:
Choose Units
Press <This Tool> --> Utility --> Choose Units to display the Choose Units pop-up window.
Press the arrow up or down buttons to highlight and select a unit of measure.
2-13
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-14 of 38
Amphion Overview
Choose Language
Press <This Tool> --> Utility --> Choose Language to display the Choose Language pop-up
window.
This screen provides a way for the operator to select English (default), or any other language (or
languages) that the operator screens are configured to support.
Press the arrow up or down buttons to highlight and select a language.
2-14
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-15 of 38
Amphion Overview
Document
General
Add
Delete
Close
This window provides a way for the operator to edit the translations for languages other than
English, or add translations that are missing.
Translations are stored in the operator screens one phrase at a time. Any single-line string on a
screen has its own translation. (For example, the phrase Drill Torque is translated as a whole, as
opposed to word-by-word.)
Each screen document has its own set of translations.
Document
Press Document to display available translations for the last screen selected. (There may be no
translations if that particular screen has not been configured to include them.)
General
Press General to display general translations that apply to the navigation bar and other common
screens (for example, the diagnostic or alarm screens).
2-15
www.nov.com
Amphion Overview
D811001248-MAN-001
Revision 01
Page 2-16 of 38
Add
Use this button to add a new translation:
1. Press Add to display the Add New Translation Key pop-up window.
2. Type the new translation into the space provided, then press Enter (or Enteray as
shown on the keyboard above).
The translation (Home in this example) appears in both the left and the right panes
of the Language Translation Editor window.
3. Press to select the new translation (in the bottom right pane) to display the keyboard
pop-up window again.
4. Type its translation as you want it to appear in that pane (see example shown
below).
2-16
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-17 of 38
Amphion Overview
5. Type the translation into the space provided, then press Enter to return to the
Language Translation Editor window.
Delete
Press Delete to delete an existing translation.
Close
Press Close to close the window.
2-17
www.nov.com
Amphion Overview
D811001248-MAN-001
Revision 01
Page 2-18 of 38
Clean Screen
Press <This Tool> --> Utility --> Clean Screen to temporarily disable tool screens to allow time
for cleaning the touchscreen without accidentally pressing tool controls. Press Start to begin the
onscreen timer, which counts slowly backward from ten.
Service Pages
Service pages are not normally available from the operator workstation touchscreens, and
therefore are not addressed in detail in this manual.
Access the service pages from the touchscreen mounted in the multi-tool controller (MTC) cabinet.
See the NOV document titled Amphion Tool Controller Service Manual for more information
about the service pages.
2-18
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-19 of 38
Amphion Overview
Press <This Tool> --> Common Diagnostics to display the Common Diagnostics menu.
See general descriptions for each diagnostic screen in the sections below.
Press Close to return to the main menu.
2-19
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-20 of 38
Amphion Overview
I/O Diagnostic
Press <This Tool> --> Common Diagnostics --> I/O Diagnostic to display the I/O Diagnostic
screen.
The left side of the sample screen below contains buttons for selecting an I/O type (depending on
the currently-selected tool). Press to select and display information.
Item Name
I/O
Types
Current Value
MOD: Modbus address. Information regarding commands originating from tools and
other Ethernet devices connected to the network.
DP1: Information from the first Applicom card on the first PROFIBUS DP network
(typically used for tools).
DP2 (optional): Information from the optional second Applicom card on the second
PROFIBUS DP network, if applicable (typically used to interface with the other tool
controllers or third-party systems).
Press any of the sort buttons located along the bottom of the screen to sort information By Name,
Node, or Class.
Press the blue arrow up or down buttons to navigate through the diagnostic pages.
Press Back to return to the Common Diagnostics menu.
2-20
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-21 of 38
Amphion Overview
The controller graphic boxes display green to indicate normal communication, or red to indicate a
communication error. The controller name and current status display in the top left corner of the
controller graphic.
Press a controller box to display additional detail.
Code
0
5632
Message
Comment
OK
2-21
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-22 of 38
Amphion Overview
Code
Message
Comment
5648
5664
Cyberbase Status
Press <This Tool> --> Common Diagnostics --> Cyberbase Status to display the Cyberbase
Status screen (not shown here).
This screen displays communication information between various NOV products using Ethernet
protocol, and is not available for all tools.
Modbus Status
Press <This Tool> --> Common Diagnostics --> Modbus Status to display the Modbus Status
screen.
The illustration shown here relates to the top drive. Green node graphics indicate that it is
operating and communicating properly; red indicates an alarm or communication error.
Press a node to display detailed information related to its status (shown below).
2-22
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-23 of 38
Amphion Overview
The Node Status pop-up window lists all WebObjects on the controller with which the
communications node is associated. It also displays the value of each WebObject. The values are
live, and change as the values from the remote controller change.
Press the Node Status window to display the nodes Process Input image.
A process image is essentially a group of bits that the controller holds in its memory to maintain a
complete map of the current state of the inputs or outputs from a given communications node. The
Process Image pop-up window displays either all of the output or all of the input process image for
that communications subsystem mode.
Press Switch to Output Image to display the same information regarding the nodes output
image.
Press anywhere outside of the output image display to return to the Modbus screen.
2-23
www.nov.com
Amphion Overview
D811001248-MAN-001
Revision 01
Page 2-24 of 38
Profibus Status
Press <This Tool> --> Common Diagnostics --> Profibus Status to display the Profibus
Network Status screen.
Green indicates the node is communicating through the Profibus network; red indicates the node is
not communicating through the network; yellow indicates the node is reporting diagnostic
information. The controller has not lost communication with the node, but the node may have a
problem (see note below).
Press any node button to display a detailed node status pop-up window.
Node number
Status code
2-24
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-25 of 38
Amphion Overview
Message
33
36
45
47
93
255
Step 7 Status
Press <This Tool> --> Common Diagnostics --> Step 7 Status to display the Step 7 Status
screen.
This screen displays information from programmable logic controllers (PLCs). This Ethernet
communication protocol not used on all communications systems.
Press any node to display additional information.
2-25
www.nov.com
Amphion Overview
D811001248-MAN-001
Revision 01
Page 2-26 of 38
Press the status detail box to display the nodes input image.
Press the right arrow to display additional input image information, or press Switch to Output
Image to display the same information regarding the nodes output image.
Press anywhere outside of the output image display to return to the Step 7 Status screen.
2-26
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-27 of 38
Amphion Overview
Press <This Tool> --> Common Diagnostics --> Screen Communication Logs to display the
main Screen Communication Logs main screen.
Press the buttons along the top of the window to display different communication information (see
general descriptions in sections below).
Press Close to return to the previous screen.
2-27
www.nov.com
Amphion Overview
D811001248-MAN-001
Revision 01
Page 2-28 of 38
Tool Controllers
Press Tool Controllers to display the Tool Controllers Communication Log screen.
Amphion software communicates simultaneously with all the tool controllers connected to the
network. The Tool Controller Communication Log screen displays basic information about each
tool controller, such as the method of communication being used between the controller and the
software, and the amount of time the software has been communicating with the tool.
Press any communication box to display message information.
2-28
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-29 of 38
Amphion Overview
2-29
www.nov.com
Amphion Overview
D811001248-MAN-001
Revision 01
Page 2-30 of 38
Ownership
Press Ownership to display tool Ownership Communication Log screen.
This window contains information about the tool ownership system, such as a record of the
ownership configuration file. Tool ownership is a built-in safety feature, designed to prevent more
than one operator from simultaneously controlling a tool. (See section titled "Tool Ownership" on
page 2-34.)
Press any of the Ownership States boxes to display more detail.
2-30
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-31 of 38
Amphion Overview
HTTP Requests
Press HTTP Requests to display the HTTP Request Communication Log window.
This window contains the last several messages passed between the touchscreen software and
the tool controllers.
Press any message to display more detail.
2-31
www.nov.com
Amphion Overview
D811001248-MAN-001
Revision 01
Page 2-32 of 38
Write Monitor
Press Write Monitor to display the Write Monitor Communication Log screen.
This window contains only requests that were used to write commands or data to the tool
controllers.
Press Close to close the window.
Exceptions
Press the Exceptions tab to display the Exceptions Communication Log screen.
This screen contains a list of errors that occurred during applet communications.
Press any message to display more detail.
2-32
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-33 of 38
Amphion Overview
2-33
www.nov.com
Amphion Overview
D811001248-MAN-001
Revision 01
Page 2-34 of 38
Tool Ownership
This section contains information about Amphion tool ownership, and is intended to provide rig
personnel with a basic understanding of the concept of tool ownership and how it affects rig
operations.
Amphion tools can be controlled from operator workstations using joysticks, discrete switches, and
touchscreen controls. For safety reasons, control of most tools is limited to one operator
(workstation) at a time.
All tools affected by Amphion tool ownership are owned by the system at startup. Consequently,
before a tool can be controlled from any workstation, the operator must submit an ownership
request by pressing the Ownership button located on the tool screen. Once a workstation
assumes ownership of a tool, that workstation retains ownership; subsequent ownership requests
from other workstations are invalid until ownership is released.
A green ownership button, displaying the word Available, indicates the tool is
available for ownership. Your station can assume ownership only if the button is
enabled, and the word Take appears in black text along the bottom of the button.
If the text Ownership appears in white, and the button is disabled, your station
cannot assume ownership of the tool. If you are unable to take ownership because
your station already has ownership of another conflicting tool, the name of that tool
appears in white text along the bottom of the button.
An orange ownership button indicates that the tool is currently owned by one of
the operators. The text display inside of the button indicates the workstation that
currently owns the tool.
A red ownership button indicates an emergency stop is engaged, and the tool is
unavailable.
2-34
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-35 of 38
Amphion Overview
Once an operator is finished using a specific tool, he or she should release ownership of that tool
by pressing the Ownership button again.
Alternatively, use the operator workstation control panels Tool Ownership - Release All button.
L
TOO IP
H
ERS
OWN SE ALL
A
RELE
INCR
DECR
EASE
L
TOO
P
RSHI
OWNE E ALL
AS
RELE
SE/
CLO
LOCK
N/
OPE
AUTO
EASE
AIR
ING
WORK RE
CMC PRESSU
APV
OW
C FL
AULI
E
HYDR VALV
CMC UT OFF
SH
SE
CLO
N
OPE
MAIN
CMC E
VALV
PULL
PAY
EAD
CATH
2-35
www.nov.com
Amphion Overview
D811001248-MAN-001
Revision 01
Page 2-36 of 38
Optional Components
RigSense and WITS
RigSense is a stand-alone drilling instrumentation system used to provide drillers and other key
personnel with instant access to critical drilling data. It can display, plot, print, export, and archive
up to 255 channels of data, which can be retrieved and viewed over the entire life of the well.
RigSense transmits and receives Wellsite Information Transfer Specification (WITS) information.
WITS is a communication protocol that enables companies operating different computer systems
to share information using a standard format for data transfer.
RigSense can easily be tailored to any rigs requirements, and the data can be viewed in either
time- or depth-based format.
See the MD Totco RigSense manual for more information.
2-36
www.nov.com
D811001248-MAN-001
Revision 01
Page 2-37 of 38
Amphion Overview
The driller can activate modes through the touchscreens, and adjust individual parameter
setpoints.
2-37
www.nov.com
Amphion Overview
D811001248-MAN-001
Revision 01
Page 2-38 of 38
2-38
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.3
Alarms & Events
www.nov.com
D811001248-MAN-001
Revision 01
Page 3-1 of 8
System Alarms
The navigation menu bars Alarms button flashes red when there is at least one active and
unacknowledged alarm. The button displays solid red when there is at least one active, but already
acknowledged, alarm. Otherwise, the button displays solid blue.
When an alarm is triggered (and unacknowledged), the Alarms button flashes red on both the
navigation menu and tool menu (for tools that have an active alarm) as shown here.
Flashing Red = Active/Unacknowledged
Solid Red = Active/Acknowledged
Tool menu
Alarms button
Navigation menu
Alarms button
3-1
www.nov.com
D811001248-MAN-001
Revision 01
Page 3-2 of 8
Press Alarms on the navigation menu to display the Alarms Menu. Flashing red tool buttons
indicate an active and unacknowledged alarm; solid red indicates an active, but acknowledged
alarm for that tool. Tools that have no active or unacknowledged alarms display solid blue.
Active/unacknowledged
alarm (flashing red)
Alarms Menu
3-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 3-3 of 8
Press to select a tool from the Alarms Menu, or press <This Tool> --> Alarms to display the
Alarm Messages window.
The alarm system displays and stores the most recent 200 alarms for the currently-selected tool.
!
All alarm data clears when electrical power is removed
from the control system.
Red line items indicate that the alarm condition is active, and the alarm itself has not
been acknowledged.
Yellow line items indicate that the alarm was acknowledged, but the alarm condition
has not been corrected.
Orange line items indicate that the alarm condition was corrected, but has not been
acknowledged.
Grey historical line items indicate that the alarm was acknowledged, and the
condition causing the alarm state was corrected.
Blue line items are events of interest that have occurred, but do not indicate an
alarm condition.
3-3
www.nov.com
D811001248-MAN-001
Revision 01
Page 3-4 of 8
The Active Date column displays the date and time the alarm was triggered.
The Inactive Date column displays the date and time the alarm was cleared.
The Acknowledged column displays the date and time the alarm was
acknowledged.
3-4
www.nov.com
D811001248-MAN-001
Revision 01
Page 3-5 of 8
The alarm detail includes an alarm ID, a description of the alarm condition, the date and time that
the alarm was tripped, cleared, and acknowledged, as well as its group, priority, and status.
The alarm shown here has not been acknowledged. Press Acknowledge to do so, then press
Close. The alarm displays yellow to indicate that it has been acknowledged (however, the alarm
condition remains active).
Press the yellow alarm line item again to view its details if necessary.
3-5
www.nov.com
D811001248-MAN-001
Revision 01
Page 3-6 of 8
Alarm Setup
Certain tool screens may contain gauges, bar graphs, or digital readings that have alarm setup
capabilities. This depends on your specific rig configuration.
Press the gauge, bar graph, or digital reading to display the Alarm Configuration pop-up window.
You can set four alarm levels: high-high, high, low, or low-low.
Press Change Level to display the pop-up keypad. Define the alarm value, then press Set to close
the keypad.
Click Enable or Disable to turn the alarm on or off.
Press the descriptions Change button to display the keyboard pop-up window. Type a brief
description of the alarm into the space provided, then press Enter to close the keyboard.
Press Close to close the Alarm Configuration pop-up window and save the values.
3-6
www.nov.com
D811001248-MAN-001
Revision 01
Page 3-7 of 8
Alarm Displays
Alarms display on the operator screen. For example, when the reading on a gauge reaches the
user-defined high alarm level (but remains below the high-high range), the graph or gauge
background displays yellow.
The same is true if the reading reaches the low range (but remains above the low-low range).
If the reading reaches the user-defined high-high range, or falls into the low-low range, the
background displays red, and the touchscreen computer (or HMI) beeps.
Alarm Sounds
Press the gauge, bar graph, or digital reading to display the Alarm Configuration pop-up window.
Disable the beeper by pressing the Turn Beeper Off.
3-7
www.nov.com
D811001248-MAN-001
Revision 01
Page 3-8 of 8
3-8
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.4
Assignments
www.nov.com
D811001248-MAN-001
Revision 01
Page 4-1 of 2
Assignments
This screen provides a way for the operator to assign VFD motors to the drawworks and the top
drive. It also displays the current status of all VFDs.
4-1
www.nov.com
Assignments
D811001248-MAN-001
Revision 01
Page 4-2 of 2
Status Displays
R
Running: Green indicates that the VFD motor is assigned and running.
Motor Lockout: Red indicates that the VFD is currently locked out.
Drawworks Select
Press any unassigned DW (A, B, C, or D) Select - VFD button to assign it to the drawworks.
A green backlight indicates the current selection.
Press the Deassign button to remove the assignment.
Press the Deassign All DW button to deassign all VFD motors from the drawworks.
See Chapter 25, titled "Top Drive System (TDS) for more
information.
4-2
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.5
Casing Running Tool (CRT)
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-1 of 20
Operator Screen
Press <Driller or AD> Tools --> Casing Tool to display the Casing Running Tool operator
screen.
The CRT is used to make up or break out a casing connection, and run the casing string to a
maximum weight of 500 short tons. It is installed on the shaft of the top drive, suspended from the
links. The top drive supplies the rotation and torque necessary to make or break a connection.
Tool Ownership
Assume ownership of the CRT to enable controls. See section titled "Tool Ownership" on page 234.
5-1
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-2 of 20
IBOP Closed: Yellow indicates the internal blowout preventer is closed; grey
indicates a normal state.
Slips Closed: Yellow indicates that the power slips are closed; green indicates that
they are open; grey indicates an inactive state. See Chapter 18, titled "Power Slips.
TDS HPU Running: Green indicates that the top drives hydraulic power unit is
running; grey indicates a normal state.
5-2
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-3 of 20
IBOP Controls
Press the Open or Close button to open or close the internal blowout preventer.
5-3
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-4 of 20
Use Drill to tilt the elevator bales backward into a position that allows drilling
operations to proceed.
Use Float to allow the elevator bales to move into a neutral position.
Use Tilt to tilt the elevator bales forward into a position that allows the elevator to
latch onto the pipe.
5-4
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-5 of 20
Break turns the CRT counter-clockwise and applies full available torque.
Spin-In turns the CRT clockwise, and applies torque and speed limits.
Press Start to begin rotating and lowering the CRT in Spin-In mode.
Press Stop to stop the process.
The graphs located on the left side of the screen display real-time speed and torque data.
Press Exit to return to the main CRT operator screen.
5-5
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-6 of 20
Make Controls
Press Make to display the Make-Up screen.
Press Accept or Reject as appropriate to save the connection data. Press Exit to return to the
previous screen.
5-6
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-7 of 20
5-7
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-8 of 20
CRT Setup
Press Casing Tool --> Setup to display the CRT Setup screen.
Keyboard
Type the information into the space provided, then press Enter to close the key pad or keyboard.
At the CRT Setup screen, press Save to store the data.
5-8
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-9 of 20
5-9
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-10 of 20
1. Either press Use to use the current setup, then skip to step 4, or;
Press Select to display the file selection screen and use a different setup file.
5-10
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-11 of 20
Use the blue arrow up or down keys to scroll through the file list (single arrows scroll
line- by-line; double arrows scroll page up or page down).
2. Highlight a file, then press Set to confirm your selection.
The currently selected file name displays along the bottom of the window.
3. Press Load to return to the Preview Pipe Type Settings screen, then press Use.
4. Press Exit to return to the Current Pipe Type Settings screen.
5. Press Exit again to return to the CRT Setup screen.
5-11
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-12 of 20
5-12
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-13 of 20
7. Press the Other Settings - Edit button to display the following pop-up window.
8. Press the Pipe Type - Edit button to display the keyboard to enter a new file name.
9. Press Exit to return to the Preview Pipe Type Edit pop-up window (shown on page
5-12).
10. At the Preview Pipe Type Edit pop-up window, review the settings, then press Use
to load the activate the settings and display the Current Pipe Type Settings screen
(shown on page 5-9).
11. Press Save to store the new file to the system.
12. Press Exit to return to the CRT Setup screen.
5-13
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-14 of 20
Cross-Thread Settings
Spin-In Settings
Make-Up Settings
5-14
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-15 of 20
On-Shoulder Settings
Over-Turns Settings
Other Settings
5-15
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-16 of 20
Calibrate
At the CRT Setup screen (shown on page 5-8), press Calibrate to display the CRT Calibration
screen.
Press any of the CRT Torque or Load Cell Torque - Edit buttons to adjust the values.
Press Save to store the calibration data, then press Exit to return to the CRT Setup screen.
5-16
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-17 of 20
CRT Review
Press Casing Tool --> Review to display the CRT Review screen.
By default, the Review screen displays torque (y-axis) versus turns (x-axis) for the currently
selected connection file.
Use the blue arrow up or down keys to scroll through the file list (single arrows scroll line-by-line;
double arrows scroll page up or page down). Highlight, then press Set to confirm your selection.
5-17
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-18 of 20
The currently-selected file name selected displays along the bottom of the window.
Press Load to display the Review screen again.
Press Refresh to display the new setup file in the Review screen.
5-18
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-19 of 20
Zoom (Y or X) In or Out
Press Zoom (Y or X) In or Out to zoom in or out. Pressing the button once zooms in to magnify the
graph to twice its 1:1 scale (2x). Press again to magnify to 4x; again to magnify to 8x, and so on.
Press Zoom Out repeatedly to return to the 1:1 (or 1x) scale.
When using the Zoom In feature, you can press (or click)
and drag the graph to display the data points you are most
interested in.
5-19
www.nov.com
D811001248-MAN-0001
Revision 01
Page 5-20 of 20
5-20
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.6
Cathead
www.nov.com
D811001248-MAN-001
Revision 01
Page 6-1 of 6
Cathead
Operator Screen
Press <Driller or AD> Tools --> Cathead to display the Cathead operator screen.
Tool Ownership
Assume ownership of the cathead to enable controls. See section titled "Tool Ownership" on page
2-34.
Status Displays
The left side of the operator screen contains vertical realtime torque and pull force graphs that
reflect their current values. Black markers indicate their user-defined setpoint values.
The Slow Speed light located along the top of the screen displays green to indicate that the mode
is active. See section titled "Slow Mode" on page 6-3.
6-1
www.nov.com
D811001248-MAN-001
Revision 01
Page 6-2 of 6
Cathead
The Maintenance Mode light displays yellow to indicate that maintenance mode is active. See
section titled "Maintenance Mode" on page 2-11.
Cathead Selection
Press Select Cathead - Break Out or Make Up.
Stream Controls
Press the Stream Controls - Pay or Pull button to define the direction of the cathead.
This function may also be controlled using the Cathead - Pay/Pull discrete switch, usually located
on the operator workstations right control panel (depending on your particular rig configuration).
L
TOO IP
H
ERS
OWN SE ALL
A
RELE
ZMS
E
RRID
OVE
D EC
REA
SE
IN
ASE
CRE
AIR
KING E
WOR
R
CMC PRESSU
APV
SE/
CLO K
LOC
N/
OPE
AUTO
OW
LIC FL
RAU ALVE
HYD
V
CMC UT OFF
SH
SE
CLO
N
OPE
MAIN
CMC E
VALV
PULL
PULL
PAY
PAY
EAD
CATH
CATH
EAD
6-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 6-3 of 6
Cathead
Slow Mode
Press the Slow Mode button to operate the cathead at a slower speed during pull-in operations.
Slow mode has no effect on pay-out operations; it is automatically energized during the first
second to prevent the line from snapping (due to tension being released too quickly) then deenergized to allow pay out at normal speed.
The Slow Speed light located along the top of the screen displays green to indicate that the mode
is active.
Define the tong length value, then press Set to confirm and close the keypad.
6-3
www.nov.com
Cathead
D811001248-MAN-001
Revision 01
Page 6-4 of 6
Define the torque setpoint value, then press Set to confirm and close the keypad. Use the arrow up
or down keys to adjust the setpoint value as needed.
Pull Force
The current Pull Force and Pull Force Setpoint values display to the right of the Torque and
Tong Length Setpoint controls. The system calculates the Pull Force Setpoint value, dividing
the torque setpoint by the tong length to define the appropriate hydraulic pressure required to
achieve the specified line pull value.
If the operator presses Pull before the closed loop control system reaches the appropriate
pressure value, an interlock message displays (pressure setpoint not reached). Once the
pressure setpoint is reached, the interlock clears, and the pull can continue normally. During the
actual pull operation, the pressure output is static, so the loop is inactive.
6-4
www.nov.com
D811001248-MAN-001
Revision 01
Page 6-5 of 6
Cathead
6-5
www.nov.com
Cathead
D811001248-MAN-001
Revision 01
Page 6-6 of 6
6-6
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.7
Chairs (Workstations)
www.nov.com
D811001248-MAN-001
Revision 01
Page 7-1 of 12
Chairs (Workstations)
7-1
www.nov.com
Chairs (Workstations)
D811001248-MAN-001
Revision 01
Page 7-2 of 12
Press AD Tools --> Assistant Chair to display the assistant drillers Chair Status screen.
Tool Signals
A green tool background indicates that the operator has ownership of the tool (as shown here).
Green tool signals indicate the current tool operation, or the position of the switch or joystick.
When the operator is not actuating the switch or button, the signal display is grey (such as the
Racker Jaw displays shown above).
Green signal displays also confirm that the signal from the discrete switch to the workstations
remote I/O and tool controller was successfully received. Failure to display green when the
workstations switch or button is actuated indicates a faulty switch or I/O point.
7-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 7-3 of 12
Chairs (Workstations)
Joystick Status
A green joystick background indicates that the joystick is in use (as shown here).
The yellow indicator on the graphs display the current position of the joystick or top wheel. If the
display does not depict the correct position (for example, if the joystick is pressed forward, but the
yellow indicator is not at the top of the y-axis), recalibrate the joystick. (See section titled "Joystick
Calibration" on page 7-10.)
Green JS Buttons display indicates that the associated button on the joystick is depressed. See
section titled "Deadman Override" on page 7-4 below.
Chair Status
24VDC PS (#1 and #2): Green indicates that the 24-volt DC power supplies are
working properly. Red indicates a fault state.
Ethernet Switch (#1 and #2): Green indicates that the Ethernet switches are
communicating properly. Red indicates a fault state.
7-3
www.nov.com
Chairs (Workstations)
D811001248-MAN-001
Revision 01
Page 7-4 of 12
Deadman Override
The trigger mounted on the front of the right joystick (also referred to as a dead man switch) must
be depressed in order to operate the drawworks or racker, unless the override is engaged.
Press and hold the Deadman Override to operate the joystick without regard to the trigger.
7-4
www.nov.com
D811001248-MAN-001
Revision 01
Page 7-5 of 12
Chairs (Workstations)
7-5
www.nov.com
Chairs (Workstations)
D811001248-MAN-001
Revision 01
Page 7-6 of 12
Status
Press <Driller or AD> Chair --> Status to display the Status menu.
The default screen is related to the local electrical room (LER) and MTC A.
Press the appropriate buttons located in the top right portion of the screen to select another status
screen.
The currently-selected screens button displays green.
7-6
www.nov.com
D811001248-MAN-001
Revision 01
Page 7-7 of 12
Chairs (Workstations)
7-7
www.nov.com
Chairs (Workstations)
D811001248-MAN-001
Revision 01
Page 7-8 of 12
<tool> OLM: Green indicates that the optical link modules are working properly; red
indicates a fault state.
Ethernet (Switches and Media Converters): Green indicates that the Ethernet
switches and converters are communicating properly; red indicates a fault state.
PS - 24 VDC Monitor: Green indicates that the 24-volt DC power supplies are
working properly; red indicates a fault state.
The ZMS Lockout light displays red to indicate that ZMS lockout is engaged; grey
indicates an idle state. See Chapter 27, titled "Zone Management System (ZMS)
for more information.
7-8
www.nov.com
D811001248-MAN-001
Revision 01
Page 7-9 of 12
Chairs (Workstations)
Red displays indicate the emergency stop is engaged. The text next to the display indicates the
emergency stop type and location
7-9
www.nov.com
Chairs (Workstations)
D811001248-MAN-001
Revision 01
Page 7-10 of 12
Calibration
Press <Driller Chair or AD> Chair --> Calibration to display the Calibration menu.
Joystick Calibration
Press <Driller or AD> Chair --> Calibration --> Joystick Calibration to display the Joystick
Calibration screen.
7-10
www.nov.com
D811001248-MAN-001
Revision 01
Page 7-11 of 12
Chairs (Workstations)
!
This process calibrates the value displayed on the operator
workstations hook load gauge. It does not affect calibration
of the hook load sensors themselves. Use this calibration
procedure only if the workstation gauge does not
correspond to the values displayed on the Drawworks
screen. See Chapter 10, titled "Drawworks.
7-11
www.nov.com
Chairs (Workstations)
D811001248-MAN-001
Revision 01
Page 7-12 of 12
7-12
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.8
Crown-Mounted Compensator
(CMC)
www.nov.com
D811001248-MAN-001
Revision 01
Page 8-1 of 6
Operator Screen
Press <Driller or AD> Tools --> Compensator to display the Compensator operator screen.
Tool Ownership
Assume ownership of the compensator to enable controls. See section titled "Tool Ownership" on
page 2-34.
Status Displays
The left side of the operator screen contains realtime air, fluid, and position graphs that reflect their
current values. A blue bar rises and falls to mark the values. The graphs also contain digital
readings.
8-1
www.nov.com
D811001248-MAN-001
Revision 01
Page 8-2 of 6
Tank Level: A text box and a status light indicate the current tank level status. Black
indicates that the pump unit is idle; green indicates that the pump unit is running,
and tank levels are normal; yellow indicates that the tank level has reached either its
high or low alarm limit; red indicates that the tank level has reached its high-high
alarm limit.
Pump Status: A text box and status lights indicate the current pump status. Black
indicates that the pump is stopped; green indicates that the pump is running
normally; red indicates a fault or alarm state. The Auto light displays green when
the pump is in Automatic mode.
!
Acknowledging the alarm does not correct the condition.
See Chapter 3, titled "Alarms and Events.
Position Status
Position status lights display green to indicate the current position.
Valve Status
Valve status lights display green to indicate that they are On (Open), or yellow to indicate that they
are Off (Closed).
Control Location
A text box displays the compensators currently-assigned control location (Amphion or Local). If
the operator takes control using the Amphion screen (see section titled "Tool Ownership" on page
8-1), the CMC can only be controlled using the Amphion interface.
8-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 8-3 of 6
L
TOO IP
H
ERS
OWN SE ALL
A
RELE
ZMS
E
RRID
OVE
N/
OPE
AUTO
SE/
CLO K
LOC
D EC
SE
REA
SE/
CLO K
LOC
N/
OPE
AUTO
EASE
INCR
OW
LIC FL
RAU ALVE
H YD
V
CMC UT OFF
SH
AIR
KING E
WOR
R
CMC PRESSU
APV
SE
CLO
N
OPE
FLOW
ULIC
DRA VALVE
Y
H
CMC UT OFF
SH
MAIN
CMC E
VALV
PULL
PAY
EAD
CATH
L
TOO IP
H
ERS
OWN SE ALL
A
RELE
ZMS
E
RRID
OVE
D EC
REA
SE
EASE
INCR
AIR
KING E
WOR
R
CMC PRESSU
APV
SE/
CLO K
LOC
N/
OPE
AUTO
OW
LIC FL
RAU ALVE
HYD
V
CMC UT OFF
SH
SE
CLO
N
OPE
SE
CLO
MAIN
CMC E
VALV
PEN
PULL
PAY
MAIN
CMC VE
VAL
EAD
CATH
8-3
www.nov.com
D811001248-MAN-001
Revision 01
Page 8-4 of 6
L
TOO IP
H
ERS
OWN SE ALL
A
RELE
ZMS
E
RRID
OVE
ASE
SE
REA
D EC
SE
REA
EASE
INCR
E
INCR
DEC
AIR
KING E
WOR
R
CMC PRESSU
APV
SE/
CLO K
LOC
N/
OPE
AUTO
OW
LIC FL
RAU ALVE
HYD
V
CMC UT OFF
SH
SE
CLO
N
OPE
MAIN
CMC E
VALV
AIR
KING E
WOR
R
C M C PR E S S U
APV
PULL
PAY
EAD
CATH
Position Preset
Press Position Preset to display the Position Preset pop-up window.
8-4
www.nov.com
D811001248-MAN-001
Revision 01
Page 8-5 of 6
8-5
www.nov.com
D811001248-MAN-001
Revision 01
Page 8-6 of 6
8-6
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.9
Conveyor
www.nov.com
D811001248-MAN-001
Revision 01
Page 9-7 of 12
Conveyor
Operator Screen
Press <Driller or AD> Tools --> Conveyor to display the Conveyor (also referred to as the
Horizontal Pipe Conveyor, or HPC) operator screen.
Tool Ownership
Assume ownership of the conveyor to enable controls. See section titled "Tool Ownership" on page
2-34.
9-7
www.nov.com
D811001248-MAN-001
Revision 01
Page 9-8 of 12
Conveyor
Tool On
E-Stop
Maintenance Mode
Hydraulics Alarm
Interlock
Auto Sequence
Press the Auto Sequence toggle button to start or stop auto sequence mode.
Use Auto Sequence mode to step through tool operations. This mode moves the conveyor belt
automatically when the operator presses the Belt - Feed In or Feed Out buttons. (See section
titled "Belt Controls and Pipe Length Display" on page 9-10.)
After releasing the Belt - Feed In or Feed Out button, the pipe continues feeding until it reaches its
destination.
A green backlight indicates that auto sequence mode is active.
9-8
www.nov.com
D811001248-MAN-001
Revision 01
Page 9-9 of 12
Conveyor
Slow Speed
Press the Slow Speed button to operate the conveyor belt at a slower speed.
Warm Up
Press the Warm Up Mode - On button to start warm-up mode.
Use Warm-up mode to warm up the conveyor hydraulics. This includes a flushing cycle that
generates heat by passing oil over a conveyor orifice, then circulating it through the manifold and
conveyor motor gear case, followed by a pre-programmed idle period.
A green backlight indicates that the mode is active.
Idle Mode
Press the Idle Mode - On button to start idle mode.
Use Idle mode to begin a low speed rotation of the conveyor belt and powered rollers to maintain a
readiness condition.
A green backlight indicates that the mode is active.
9-9
www.nov.com
Conveyor
D811001248-MAN-001
Revision 01
Page 9-10 of 12
A digital reading of the current system-calculated pipe length displays above the controls.
9-10
www.nov.com
D811001248-MAN-001
Revision 01
Page 9-11 of 12
Conveyor
9-11
www.nov.com
Conveyor
D811001248-MAN-001
Revision 01
Page 9-12 of 12
9-12
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.10
Drawworks
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-1 of 50
Drawworks
Press Drawworks --> Drilling to display the Drawworks Drilling screen. See illustration on the
following page and the section titled "Drawworks Menu" on page 10-25.
10-1
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-2 of 50
Tool Ownership
Assume ownership of the drawworks from the Drawworks Tripping screen.
See section titled "Tool Ownership" on page 2-34.
10-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-3 of 50
Drawworks
10
E-Stop
Brake System
Drive System
Chair System
Other Alarms
Override
Power Limit
CSB Deployed
Displays red when the casing stabbing basket is not in its home
position, or grey when it is. If the CSB is not parked, the drawworks
speed is reduced to 10% of the user-defined speed settings.
ZMS Off
10-3
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-4 of 50
CMC (Sensor
Fault, Comm Fault,
Locked, Inhibit
Unlock)
Green Opened or Closed displays indicate the current trip tank valve
position.
A Standpipe Pressure reading, located in the top right corner of both the Drawworks Drilling
and Drawworks Tripping screens, displays the current pressure sensor reading.
10-4
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-5 of 50
Drawworks
10
DRIL
TDS
LINK
TILT
FLO
AT
OPE
TDS
CLO
SE
LINK
OPE
N
CLO
SE
TDS
EL
OFF
/AUT
O
EVA
TOR
RAC
KER
ON
JAW
OFF
/AUT
O
ON
DRA
W
OVE WORKS
RR
IDE
PAR
K
DOLL
Y
ING
BRA
KE
PAR
K
ING
BRA
KE
ENA
BLE
SLIP
S EN
OPE
N
ABLE
CLO
SE
IBOP
10-5
www.nov.com
10
D811001248-MAN-001
Revision 01
Page 10-6 of 50
Drawworks
Derrick Graphics
The Drawworks Tripping screen derrick graphic contains markers for both high and low travel
limits and stops.
The Drawworks Drilling screen graphic also contains markers for high travel limits, and a yellow
Drill Stop Point marker (low travel stops are not marked).
Proximity indicators on both screens display red to indicate a fault or open circuit state.
Block and
elevator positions
Low travel stop
Low travel limit
Tripping screen
10-6
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-7 of 50
Drawworks
10
Red block and elevator position backgrounds indicate that the block requires calibration. See
section titled "Block and Elevator Position Calibration" on page 10-38.
10-7
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-8 of 50
Use the High Travel Limit keypad to define the maximum block height value, then press Set to
confirm the value and close the keypad.
Use the High Travel Stop keypad to define the high travel stop value. The block stops here before
reaching its maximum travel limit. Press Set to confirm the value and close the keypad.
To continue travel to the High Travel Limit after stopping at the High Travel Stop, zero the
joystick (return to home position), then move the joystick again in the hoist direction.
Use the Low Travel Limit keypad to define the lowest possible block height value, then press Set
to confirm the value and close the keypad.
Use the Low Travel Stop keypad to define the low travel stop value. The block stops here before
reaching its Low Travel Limit. Press Set to confirm the value and close the keypad.
To continue travel to the Low Travel Limit after stopping at the Low Travel Stop, zero the joystick
(return to home position), then move the joystick again in the lower direction.
10-8
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-9 of 50
Drawworks
10
Use the Drill Stop Point keypad to define a Drill Stop Point value.
R
Enter a negative value to allow the elevators to travel below the drill floor, and the
Link-Tilt feature of the top drive to be used. When the links are fully retracted (in
Drill mode), the top drive elevators are raised several feet above their normal
(Float) position. The blocks are then able to travel to a lower position before the
elevators come in contact with the drill floor.
10-9
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-10 of 50
Define maximum speed values, then press Set to confirm and close the keypad.
10-10
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-11 of 50
Drawworks
10
Buttons
not used
Dead man
switch
Lower
Hoist
See section titled "Defining Maximum Block Speeds" on page 10-10, and section titled "Auto
Reaming Setup" on page 10-23.
10-11
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-12 of 50
Define a maximum weight value for the drawworks, then press Set to confirm the value and close
the keypad.
10-12
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-13 of 50
10
Drawworks
At the Drawworks Tripping screen, press Mode Select to display the automated drawworks
system ADS Mode Select window.
Normal
Use to operate the drawworks at 100% of the maximum speed.
Brake Only
Use in power loss situations. Brake Only mode allows free spooling of the drill line and limits
operation of the drawworks to brake use only, at the user-defined maximum speed.
See section titled "Defining Maximum Block Speeds" on page 10-10.
10-13
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-14 of 50
Slip & Cut mode bypasses High and Low Travel Limit
settings, allowing free movement of the block without
position protection. Potential damage to equipment or
injury to personnel exists. Exercise extreme caution in
this mode.
1. Ensure that motors are assigned and auxiliaries are turned on.
2. Press to select Slip & Cut mode to display the Confirm Slip & Cut Operation popup window.
3. Press Yes! Start Slip & Cut from Driller Chair or Local Station to display the
associated Slip & Cut Control screen (see below).
Alternatively, press No to abort the procedure and return to the previous screen.
10-14
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-15 of 50
Drawworks
Driller Chair
10
Local Station
4. Press the RPM button to display the maximum drum speed keypad.
5. Define a maximum drum revolution speed value using the keypad, then press Set to
confirm and close the keypad.
6. If you choose to perform this procedure from the drillers chair:
Q
After closing the keypad, press OK, then perform the necessary slip and cut
operations.
Press Close. The drawworks mode resets to Normal, and the operation is
complete.
10-15
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-16 of 50
7. Press Transfer To Local to request that control be transferred to the local control
station.
The Local Station indicator flashes green when the transfer request is received,
and displays solid green when accepted.
8. From the local control station, turn the switch to Local to accept the transfer
request.
9. Perform the necessary slip and cut operations, then request that control be returned
to the driller by turning the switch mounted on the local control panel to Drillers
Control.
10. Press Accept Control from the operator workstation touchscreen (shown above).
10-16
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-17 of 50
10
Drawworks
The indicator flashes green until the operator accepts the transfer.
11. Press Close.
The drawworks mode resets to Normal.
Press Mode Select again to display the drawworks Mode Select pop-up window
(see page 10-13) to select another mode.
!
Perform a full block calibration after each slip & cut
operation. See section titled "Block and Elevator Position
Calibration" on page 10-38.
10-17
www.nov.com
10
D811001248-MAN-001
Revision 01
Page 10-18 of 50
Drawworks
Autodrill Mode
Autodrill mode launches (and allows operation of the drawworks through) the Electronic Driller
System (EDS) application.
!
The driller is responsible for ensuring that the crownmounted compensator (CMC) is locked, and the position
status reflects little or no ocean heave prior to activating
Autodrill Mode. Excessive heave could cause damage to
equipment and rig down time. Extreme care should be
taken when using Autodrill mode. See Chapter 8, titled
"Crown-Mounted Compensator (CMC) for more
information.
10-18
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-19 of 50
10
Drawworks
Digital readings display above each parameters vertical graph. Black markers on the graphs mark
the user-defined setpoint values.
Activate or
Deactivate
10-19
www.nov.com
10
D811001248-MAN-001
Revision 01
Page 10-20 of 50
Drawworks
Activate or
Deactivate
Variable Adjust
Current
Setpoint Value
Define
Setpoint
Define the setpoint value, then press Set to confirm the value and return to the Drilling screen.
10-20
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-21 of 50
10
Drawworks
Variable Adjustment
The real-time drilling trend display (see section titled "Drilling Trends below) is driven by digital
signals received at certain intervals. Dampening (also referred to as time-constant adjustment)
can improve the readability of the weight on bit (WOB) and delta pressure displays by limiting the
frequency of the display update.
Press the (WOB or Delta P) Variable Adjust button to display its pop-up window.
Variable Adjust
You can also zero the or adjust the parameter value at this
screen by pressing Zero WOB or Zero Delta P.
10-21
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-22 of 50
Drilling Trends
Press Drilling Trends to display a real-time graph that charts the data for activated drilling
parameters. The colors on the graph correspond to the active parameters on the Drawworks
Drilling screen.
Drag the slider, or use the blue Lower or Higher buttons to adjust the appropriate variables gain
factor.
Press Close Trend to close the Drilling Parameter Trends window.
10-22
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-23 of 50
10
Drawworks
!
The driller is responsible for ensuring that the crownmounted compensator (CMC) is locked, and the position
status reflects little or no ocean heave prior to using Auto
Reaming. Excessive heave could cause damage to
equipment and rig down time. Extreme care should be
taken when using Auto Reaming mode. See Chapter 8,
titled "Crown-Mounted Compensator (CMC) for more
information.
At the Drawworks Drilling screen, press the Reaming button to display the Auto Reaming setup
screen.
Enable: Press the Enable button to enable and disable the reaming feature. The
text display changes to reflect the status.
Pull Limit: Press the Pull Limit button to display the keypad. Define a maximum
pull weight value, then press Set to close the keypad. The system reduces pull
speed as the real load weight approaches this setpoint value.
Hoist and Lower Speed: Press the Hoist or Lower Speed button to display the
keypad. Define a maximum speed value (in feet per hour), then press Set to close
the keypad.
Distance: Press the Distance button to display the keypad. Define the distance
between the block and the drill stop setpoint during reaming operations, then press
Set to close the keypad. Once the block hoists this distance, it lowers at the userdefined Lower Speed setpoint value.
10-23
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-24 of 50
10-24
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-25 of 50
Drawworks
10
Drawworks Menu
From any Drawworks screen, press the Drawworks button located on the main menu bar to
display its tool menu.
10-25
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-26 of 50
Auxiliary Control
Press Drawworks --> Motor Controls --> Auxiliary Control to display the Auxiliary Control
screen.
Press the appropriate Stop or Start button to enable or disable a blower or lube pump motor.
Motor Running lights display green to indicate that the motor is running.
Air Pressure lights display red to indicate a fault or alarm condition; black to indicate a normal
state.
10-26
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-27 of 50
10
Drawworks
Assignments
Press Drawworks --> Motor Control --> Assignments to display the Drawworks/Top Drive
Assignments screen.
This screen provides a way for the operator to assign VFD motors to the drawworks and the top
drive. It also displays the current status of all VFDs.
See Chapter 4, titled "Assignments for more information.
10-27
www.nov.com
10
D811001248-MAN-001
Revision 01
Page 10-28 of 50
Drawworks
Drum Encoders
Press Drawworks --> Tool Diagnostic --> Drum Encoders to display the Drum Encoders
screen.
Status Displays
R
!
For safety reasons, NOV recommends that all three
encoders are enabled at all times.
10-28
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-29 of 50
Drawworks
10
Status Displays
R
Hook Load: Displays weight on the drill string according to each sensor.
!
For safety reasons, National Oilwell Varco recommends
that all three sensors be enabled at all times.
10-29
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-30 of 50
Compensator Sensors
Press Drawworks --> Tool Diagnostic --> Compensator Sensors to display the Compensator
Sensors screen.
Status Displays
R
10-30
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-31 of 50
10
Drawworks
Status Menu
Press Drawworks --> Status to display the Drawworks Status menu.
.
Drawworks Status
Press Drawworks --> Status --> Drawworks Status to display the Drawworks Status screen.
10-31
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-32 of 50
Alarms Reset
Press Alarms Reset to reset alarm displays after appropriate action has been taken to clear the
condition.
Motor Displays
R
A green Blower Running display indicates that the blower is running normally;
black indicates a normal or idle state; red indicates a fault or alarm condition.
A red Diff Pressure Low display indicates that the difference between the suction
and the exhaust of the blower is too low, and the motor is not receiving proper air
flow.
The motor Speed reading displays the current speed (rpm) value.
A green VFD Status display indicates that the VFD is running; black indicates an
idle or normal state; red indicates a fault or alarm condition.
10-32
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-33 of 50
10
Drawworks
!
The system must be parked with minimal hook load (empty
traveling assembly) prior to beginning this test.
At the Drawworks Status screen, press Capacity Test to display the Brake Capacity Test popup window.
10-33
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-34 of 50
Green Pass displays indicate that the brake passed the test; red Fail displays indicate that the
brake failed the test.
Brake load capacity readings display beneath the Pass/Fail displays.
Press Close to return to the Drawworks Status screen.
10-34
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-35 of 50
10
Drawworks
Press Measure Brake 1 or Measure Brake 2 to put that Brake into the proper state for
measurement. Brake 1 is the one on the left if facing the drum. In order to test the other brake or to
close the dialog, press the Reset button.
Press Reset to select Measure Brake 2 or to close.
10-35
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-36 of 50
Oil Temperature
Oil Pressure
Elevator Position
Drum Setpoint
Drum Speed
Park Status
Motor/VFD Status
Press Drawworks --> Status --> Motor/VFD Status to display the Motor/VFD Status Detail
screen.
This screen contains current chopper motor status (health and air flow) and drawworks VFD status
(speed, torque, and winding temperature readings).
Status indicators display the following information:
Health
Displays green to indicate that the chopper is online and operating normally; red
to indicate a fault or alarm state; black to indicate that the chopper is offline.
Displays green to indicate that the drawworks brake resistor air flow fan is on and
operating normally; black to indicate it is off.
Ready
Assigned
10-36
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-37 of 50
10
Drawworks
Fault
Running
Press the VFD Fault Reset button to reset the VFDs after the appropriate action has been taken
to clear faults.
10-37
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-38 of 50
Calibration Menu
Press Drawworks --> Calibration to display the Drawworks Calibration menu.
1. Ensure that the system is parked, then press Full Calibration to begin.
10-38
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-39 of 50
Drawworks
10
4. Press to select the correct number of lines strung, then press Close.
5. Press Continue to display the next Block Height Calibration screen.
6. Move the drum to a transition between layers, then press the button that
corresponds to that layer transition (1st, 2nd, or 3rd).
10-39
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-40 of 50
8. Lower the block until the elevator rests on the slips, rotary table, or at a known height
position, then press the Set Elevator Position button to display its keypad.
9. Enter the correct elevator height value, then press Set to close the keypad.
10. Verify the value, then press Set Elevator Position and Continue.
10-40
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-41 of 50
Drawworks
10
!
Select the manual method only if the system cannot
automatically calculate the length of the assembly due to
unavailable targets (for example, if the top drive is parked
in the side skid), or due to proximity switch failure.
!
The block travel speed is no longer reduced to 25%; it now
moves at 100%.
10-41
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-42 of 50
13. If you selected Enter Length of Assembly Manually, the following screen appears.
Follow the remaining steps of this procedure.
14. Manually measure the length of the traveling assembly (from the top of the block, to
the bottom of the elevator).
15. Press the measurement button, then enter the value using the keypad.
16. Press Set to close the keypad.
10-42
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-43 of 50
Drawworks
10
!
The block travel speed is no longer reduced to 25%; it now
moves at 100%.
The first Block Height Calibration screen displays (partial screen shown here).
10-43
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-44 of 50
19. Press Elevator Position Calibration to display the Elevator Position Reset
screen.
20. Move the elevator to a known position (such as the drill floor at 0.0 feet), then press
the New Elevator Position button to display the keypad.
21. Define the position, then press Set to confirm the value and close the keypad.
The following screen appears.
10-44
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-45 of 50
Drawworks
10
22. Press Set Elevator Position to store the value, then press Close.
Elevator position calibration is complete.
10-45
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-46 of 50
10-46
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-47 of 50
10
Drawworks
Standpipe Calibration
!
Turn mud pumps off before performing his procedure.
Press Drawworks --> Calibration --> Standpipe Tare to display the Standpipe Sensor
Selection and Tare screen.
Press Use Sensor (1 or 2) to select a sensor, then press Zero Standpipe Pressure to zero the
reading.
10-47
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-48 of 50
CMC Calibration
Press Drawworks --> Calibration --> CMC Calibration to display the Compensator Position
Calibration screen.
10-48
www.nov.com
D811001248-MAN-001
Revision 01
Page 10-49 of 50
10
Drawworks
Alarms
Alarm Definitions
Trip
Action taken by the control system in response to an abnormal condition.
Abnormal Condition
R
Fault
R
Instrument failure or process condition that makes the signal to the control system
greater than 20.2 ma, or less than 3.8 ma.
A condition in which two components on the a same circuit are not in the same state
(for example, a switch and relay not in the same state where monitored).
Alarm
A text message displayed on the alarm banner and the Alarms screen until cleared. Abnormal
conditions, faults, soft trips, and all category stops generate an alarm.
Soft Trip
A condition where continued operation may cause damage to the drawworks or its associated
systems. The trip bit is set, and an alarm triggers, notifying the driller of the condition. When the
driller moves the joystick below the +/- 25% position, commands above 25% are limited to 25% of
the driller-defined maximum. Once the system is parked, it remains parked until the fault is cleared
or acknowledged.
10-49
www.nov.com
10
Drawworks
D811001248-MAN-001
Revision 01
Page 10-50 of 50
Category 2 Stops
R
The first type of category 2 stop is a controlled stop with power remaining available
to the VFDs/motors. Joystick commands are disabled. After drum speed is reduced
to zero rpm, the spring brakes are set. Once they are engaged and the load is
secured, the speed and torque commands to the VFDs are zeroed. If the system
cannot be decelerated by the motors, the friction brakes stop the drum before the
solenoid valves de-energize, and the system initiates a Category 2 - Brake Only
stop (described below).
The second type is referred to as a Brake Only stop, which is a controlled stop that
reduces joystick movement commands to zero. VFDs shut down, and the friction
brake speed controller decelerates the system to zero rpm. After drum speed
reaches zero rpm, power to the brake systems solenoid valves is removed, which
sets the spring-applied brakes.
The third type is referred to as a Category 2 Stop Open Loop stop, which initiates
the same sequence of events as the Brake Only stop, except the friction brake is
applied to achieve a calculated deceleration rate, without speed control. This stop is
initiated when an encoder fault is detected, and the system cannot determine which
encoder is valid.
E-Stop (Category 0)
Category 0 emergency stops immediately remove power to the VFDs and motors (uncontrolled
stop; VFDs trip and coast to a stop), removes pressure from the spring-applied brakes, and applies
full pressure to air-applied service brakes. This stop can be initiated either automatically by the
control system, or by manually pushing the E-Stop button located on the driller workstation control
panel.
If a system has two chairs, the E-Stop button on the chair that has ownership of the drawworks
initiates a Category 0 E-Stop. The E-Stop on the other chair will initiate a Category 2 E-Stop.
Normally, that would mean that the E-Stop button on the drillers chair will initiate a Category 0 EStop and the one of the AD chair will cause a Category 2 E-Stop. However, if the AD has
ownership of the drawworks, then the AD chairs E-Stop button will cause the Category 0 E-Stop
and the drillers chair E-Stop button will cause the Categoy 0 E-Stop.
10-50
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.11
Driller Auxiliaries
www.nov.com
D811001248-MAN-001
Revision 01
Page 11-1 of 4
Driller Auxiliaries
Operator Screen
Press <Driller or AD> Tools --> Driller Auxiliaries to display the first Driller Auxiliaries screen.
11-1
www.nov.com
11
Driller Auxiliaries
D811001248-MAN-001
Revision 01
Page 11-2 of 4
11-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 11-3 of 4
Driller Auxiliaries
11
11-3
www.nov.com
11
Driller Auxiliaries
D811001248-MAN-001
Revision 01
Page 11-4 of 4
Green indicators reflect all mud treatment tools currently running; grey indicators reflect an idle
state; red indicators reflect a fault state or communication error.
11-4
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.12
Fingerboard
www.nov.com
D811001248-MAN-001
Revision 01
Page 12-1 of 4
Fingerboard
Operator Screen
Press <Driller or AD> Tools --> Fingerboard to display the Fingerboard operator screen.
While latches are closed, pipes in the fingerboard display as solid black circles, and contain a
white number assignment. A black number inside a white circle signifies an empty pipe slot.
Empty slots
12-1
www.nov.com
12
Fingerboard
D811001248-MAN-001
Revision 01
Page 12-2 of 4
Press anywhere outside of the work area to display the main Fingerboard screen.
12-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 12-3 of 4
Fingerboard
12
12-3
www.nov.com
12
Fingerboard
D811001248-MAN-001
Revision 01
Page 12-4 of 4
Fingerboard Setup
Press Fingerboard --> Setup to display the Fingerboard Setup menu.
Follow the onscreen instructions to define the finger values, then press Accept Positions.
12-4
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.13
Foxhole
www.nov.com
D811001248-MAN-001
Revision 01
Page 13-1 of 4
Foxhole
Operator Screen
Press <Driller or AD> Tools --> Foxhole to display the Foxhole operator screen.
Tool Ownership
Assume tool ownership of the foxhole to enable controls. See section titled "Tool Ownership" on
page 2-34.
13-1
www.nov.com
13
Foxhole
D811001248-MAN-001
Revision 01
Page 13-2 of 4
Status Displays
The right side of the screen contains status and alarm displays.
R
Foxhole Open: Displays green to indicate that the foxhole is open; grey to indicate it
is not.
Foxhole Closed: Displays green to indicated that the foxhole is closed; grey to
indicate that it is not.
PRS Comms Lost: Displays red to indicate a communication fault with the pipe
racking system; grey to indicate that communication is normal.
Foxhole Controls
Press Controls - Open or Close buttons to open or close the foxhole.
13-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 13-3 of 4
Foxhole
13
Override Controls
If the racker is not positioned directly above the foxhole, you can use the Override controls to open
the foxhole.
Press and hold the Interlock - Override button to override normal operating requirements for the
foxhole.
!
For safety reasons, this function must be activated from
another touchscreen.
13-3
www.nov.com
13
Foxhole
D811001248-MAN-001
Revision 01
Page 13-4 of 4
13-4
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.14
Hydraulic Power Unit (HPU)
www.nov.com
D811001248-MAN-001
Revision 01
Page 14-1 of 4
Operator Screen
Press <Driller or AD> Tools --> HPU to display the Hydraulic Power Unit screen.
14-1
www.nov.com
14
D811001248-MAN-001
Revision 01
Page 14-2 of 4
Status Displays
Motor Status
Displays along the top of the screen indicate the status of each HPU motor.
Control Location
Displays along the right side of the screen indicate each motors current control location.
Green displays indicate the assigned location; all grey displays indicate that the control location is
either unassigned or unavailable.
R
Motor <#> Auto: Indicates that only the driller or assistant driller can control the
HPU using the Amphion interface. See section titled "HPU Controls" on page 14-3.
Motor <#> Local: Indicates that the HPU motor can only be controlled from the
HPU itself.
Motor <#> Remote: Indicates that a previously set up remote station (not located at
tool itself) can control the HPU motors. While the driller or assistant driller can still
control the motors in this state, they can still be turned on or off at this remote
station.
Messages
Operator messages display along the bottom of the screen.
14-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 14-3 of 4
14
HPU Controls
Motor controls are enabled on this screen only if the motor status is Available (see section titled
"Motor Status" on page 14-2), and the current control location status is set to Auto or Remote
(see section titled "Control Location" on page 14-2).
Press the appropriate motors Stop or Start button to stop or start a motor.
14-3
www.nov.com
14
D811001248-MAN-001
Revision 01
Page 14-4 of 4
HPU Menu
Press the HPU button to display its tool menu.
14-4
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.15
Mud Bucket
www.nov.com
D811001248-MAN-001
Revision 01
Page 15-5 of 8
Mud Bucket
Operator Screen
Press <Driller or AD> Tools --> Mud Bucket to display the Mud Bucket operator screen.
Tool Ownership
Assume tool ownership of the mud bucket to enable controls. See section titled "Tool Ownership"
on page 2-34.
15-5
www.nov.com
15
Mud Bucket
D811001248-MAN-001
Revision 01
Page 15-6 of 8
Status Displays
A green Stowed display indicates that the mud bucket is in a stowed position.
A yellow Maintenance Mode display indicates maintenance mode is engaged. See section titled
"Maintenance Mode" on page 2-11 for more information.
Jaw
Press Open or Close to control jaw movement.
15-6
www.nov.com
D811001248-MAN-001
Revision 01
Page 15-7 of 8
Mud Bucket
15
15-7
www.nov.com
15
Mud Bucket
D811001248-MAN-001
Revision 01
Page 15-8 of 8
15-8
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.16
Mud Pumps
www.nov.com
D811001248-MAN-001
Revision 01
Page 16-1 of 10
Mud Pumps
Operator Screen
Press <Driller or AD> Tools --> Mud Pumps to display the Mud Pumps operator screen.
Tool Ownership
Assume ownership of the mud pumps to enable controls. See section titled "Tool Ownership" on
page 2-34.
16-1
www.nov.com
16
Mud Pumps
D811001248-MAN-001
Revision 01
Page 16-2 of 10
Auxiliaries OK: Displays grey to indicate an idle state; green to indicate that
auxiliaries are running properly; red to indicate a fault state.
Drive OK: Displays green to indicate that the drive is running properly; grey to
indicate an idle state; red to indicate a fault state.
Power Limit: Displays red when the system is limiting the power, and its speed
command is being dynamically reduced; yellow when the power limit speed
reduction is released, and the tool is ramping back up to its last speed command;
green when power is not limited, and the tool is operating at its current speed
command. See Chapter 19, titled "Power System.
A digital SPM reading displays at the top of the graph, and a blue bar rises and falls on the vertical
graph to mark the current reading.
16-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 16-3 of 10
Mud Pumps
16
Define a maximum SPM value, then press Set to confirm the value and close the keypad.
Use the blue arrow up or down buttons to incrementally increase or decrease this value.
The current user-defined SPM Setpoint value displays on the control button.
A blue bar rises and falls to mark the current reading, and a digital reading displays at the top of
the graph.
16-3
www.nov.com
16
Mud Pumps
D811001248-MAN-001
Revision 01
Page 16-4 of 10
Define a maximum pressure limit value, then press Set to confirm the value and close the keypad.
The current user-defined Pressure Limit value displays on the control button.
Press the Controls - Pause button to slowly stop and pause a pump motor.
Press the Controls - Pause button again to return a mud pump to its previously
operating SPM.
16-4
www.nov.com
D811001248-MAN-001
Revision 01
Page 16-5 of 10
Mud Pumps
16
Press the Controls - Pause button again to return a mud pump to its previously operating SPM.
(See section titled "Starting and Pausing Mud Pump Motors" on page 16-4.)
Press Misc Controls to display MP (1, 2, and 3) Aux Override and Fault Reset controls along the
bottom of the Mud Pump operator screen.
Safety interlocks prevent certain auxiliary operations from engaging where applicable. If an
operation must be performed without interlocks, press and hold the MP (1, 2, or 3) Aux - Override
button while issuing commands. (See section titled "Auxiliary Controls" on page 16-8.)
Press the Fault - Reset button to reset fault displays after appropriate action has been taken to
clear the condition.
Press Messages to display operator messages again.
16-5
www.nov.com
16
Mud Pumps
D811001248-MAN-001
Revision 01
Page 16-6 of 10
16-6
www.nov.com
D811001248-MAN-001
Revision 01
Page 16-7 of 10
Mud Pumps
16
All information on the Mud Pump Status screen is display-only. Digital speed (command and
actual), SPM, torque (limit and actual), and temperature (winding and bearing) readings display in
the center portion of the screen. (See section titled "Defining Maximum SPM Values" on page 163.)
Status and fault indicators display along the left and top/center portions of the screen:
R
Drive Monitor - Ready: Displays green to indicate that the drive is ready; grey to
indicate an idle state.
Drive Monitor - Assigned: Displays green to indicate that the drive is assigned;
grey to indicate it is unassigned.
Drive Monitor - Fault: Displays red to indicate a fault state; grey to indicate a
normal state.
(Liner Wash and Pre-Charge) Pump Running: Displays green to indicate that the
pump is running; grey to indicate an idle state.
Blower Running: Displays green to indicate that the blower is running; grey to
indicate an idle state.
Blower Pressure Switch: Displays red to indicate a pressure switch fault; grey to
indicate a normal state.
Press Mud Pump (#2 or #3) to display the same status screen for another mud pump.
16-7
www.nov.com
16
Mud Pumps
D811001248-MAN-001
Revision 01
Page 16-8 of 10
Auxiliary Controls
Press Mud Pumps --> Auxiliary Controls to display the default Mud Pump #1 Auxiliary
Controls screen.
Assume ownership of the mud pumps to enable controls. See section titled "Tool Ownership" on
page 16-1.
Press Mud Pump (#2 or #3) to display the same screen for another mud pump.
Motor Running: Displays green to indicate that the motor is running; grey to
indicate an idle state.
Air Pressure: Displays green to indicate that blowers air pressure value is within an
acceptable range; red to indicate that pressure has fallen below an acceptable level.
Water Pressure: Displays green to indicate that the liner wash or charge pumps
water pressure value is within an acceptable range; red to indicate that pressure has
fallen below an acceptable level.
Oil Pressure: Displays green to indicate that the lube pumps oil pressure value is
within an acceptable range; red to indicate that pressure has fallen below an
acceptable level.
16-8
www.nov.com
D811001248-MAN-001
Revision 01
Page 16-9 of 10
Mud Pumps
16
16-9
www.nov.com
16
Mud Pumps
D811001248-MAN-001
Revision 01
Page 16-10 of 10
16-10
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.17
Ownership Overview
www.nov.com
D811001248-MAN-001
Revision 01
Page 17-1 of 2
Ownership Overview
Operator Screen
Press <Driller or AD> Tools --> Ownership Overview to display the Tool Ownership Overview
screen.
A text box and status light indicate the current ownership state of each tool.
R
A green status light indicates that one of the operators currently own the tool. The
text box beneath displays the current owner.
A red status light indicates that the tool is unavailable. The text box beneath
provides additional information (for example, the text box displays E-Stop if the
emergency stop is engaged).
See section titled "Tool Ownership" on page 2-34 for more information.
17-1
www.nov.com
17
D811001248-MAN-001
Revision 01
Page 17-2 of 2
Ownership Overview
17-2
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.18
Power Slips
www.nov.com
D811001248-MAN-001
Revision 01
Page 18-1 of 6
Power Slips
Operator Screen
Press <Driller or AD> Tools --> Power Slips to display the Power Slips operator screen.
Tool Ownership
If the joystick does not offer power slip controls, then press the Ownership button located in the
bottom right corner of the screen to assume ownership and enable controls.
If the joystick has the ability to control both the power slips and the drawworks, the workstations
left control panel will contain a button that must be pressed in order to enable the power slips and
allow the operator to assume ownership.
18-1
www.nov.com
18
D811001248-MAN-001
Revision 01
Page 18-2 of 6
Power Slips
If this is the case, push the Slips Enable button, then assume ownership of the power slips to
enable controls.
DRIL
TDS
LINK
OPE
TILT
FLO
AT
TDS
CLO
SE
LINK
OPE
N
CLO
SE
TDS
ELE
VATO
R
RAC
KER
OFF
/AUTO
JAW
CLO
S
DRAW
OVE WORKS
RRID
E
PAR
KIN
G BR
AKE
DOLL
Y EN
ABLE
SLIP
OPE
N
S EN
ABLE
CLO
SE
IBOP
SLIP
S EN
ABL
Status Displays
The top left portion of the Power Slips operator screen contains fault and status displays.
A red display indicates that the pressure value has fallen below an
acceptable level; grey indicates a normal state.
Slips Open or
Slips Closed
Maint Mode
RST Locked
A red display indicates the rotary support table is locked; grey indicates
an idle state. See Chapter 22, titled "Rotary Table.
18-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 18-3 of 6
18
Power Slips
Alternatively, either the operator workstations right joystick or left control panel offers power slip
controls, depending on your particular rig configuration.
Open Slips
OFF
/AUT
O
ON
Close Slips
OPE
N
TDS
BR
OPE
N
CLO
S
OPE
N
AKE
TDS
FLO
AT
CLO
SE
DRIL
POW
ER S
L
CLO
SE
IPS
TILT
OPE
N
CLO
SE
TDS
IBOP
TDS
Dead man
switch
LINK
TDS
EL
OPE
N
RAC
KER
X
OVE /Y
RRID
E
OFF
/AUT
O
PAR
K
ING
BRA
RAC
K
TRA E R
OVE VEL
RRID
E
ON
POW
EVA
TOR
ER S
LIPS
CLO
SE
RAC
KE
JAW R
S
KE
A
OVE DS
RRID
E
Either use the buttons on the top right side of the joystick, or the Power Slips - Open or Close
discrete switch to control the slips.
See section titled "Workstation Control Panels" on page 2-4 for more information.
18-3
www.nov.com
18
Power Slips
D811001248-MAN-001
Revision 01
Page 18-4 of 6
A red Grease Level display indicates that the grease has fallen below an acceptable level.
A digital reading displays the number of cycles completed since the last greasing.
18-4
www.nov.com
D811001248-MAN-001
Revision 01
Page 18-5 of 6
Power Slips
18
18-5
www.nov.com
18
Power Slips
D811001248-MAN-001
Revision 01
Page 18-6 of 6
18-6
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.19
Power System
www.nov.com
D811001248-MAN-001
Revision 01
Page 19-1 of 14
Power System
Overview
The purpose of the Amphion power system is to monitor and analyze the status of the drilling
power source, and report power capacity and power consumed values to each tool. From these
values, each tool calculates a power available value:
Power Available = Power Capacity Power Consumed
Programming code stored on each tools controller determines whether power available is
sufficient for its purposes, or if the tool needs to go into power limit mode.
For more information about power calculations:
R
On smaller rigs, the Amphion power system may be the only power management system on the
rig. In this case, it monitors the status of the generators or utility power directly. It also monitors the
overall system load, in addition to the drilling load.
On larger rigs, the Amphion power system may be integrated as a sub-component to a larger
overall power management system (PMS). In this case, it is normally the rigs power management
system that sends power availability signals to the Amphion power system for drilling purposes
only; the Amphion power system would not manage the overall system load.
In either case, the primary objective of the Amphion power system is to deliver power availability
information to all drilling tools in order to prevent a system overload and blackout.
19-1
www.nov.com
19
D811001248-MAN-001
Revision 01
Page 19-2 of 14
Power System
Operator Screen
Press <Driller or AD> Tools --> Power System to display the Power System Overview (also
referred to as the One-Line Status screen).
All information on this screen is display-only. Please note that this screen may not reflect your
particular rig configuration.
Screen Symbols
Green symbols indicate an on, running, or closed state; red symbols indicate an off, stopped, or
open state; white symbols indicate an unknown status.
Inverter (INV)
Rectifier
Silicon-Controlled
Rectifier (SCR)*
*not applicable on all rigs
19-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 19-3 of 14
Power System
19
19-3
www.nov.com
19
D811001248-MAN-001
Revision 01
Page 19-4 of 14
Power System
Drives
Press Drives to display the Drive Status menu.
Inverters
Press Drives --> Inverters to display the Inverters Status screen.
All information on this screen is display-only. Please note that this screen may not reflect your
particular rig configuration.
Two vertical graphs display the selected drives current motor speed and torque values. A blue bar
rises and falls to mark the current reading. A digital reading also displays at the bottom of both
graphs.
Status displays indicate the current state for each of the following:
Ready
Running
Fault
19-4
www.nov.com
D811001248-MAN-001
Revision 01
Page 19-5 of 14
Power System
Encoder Fault
Disconnect Closed
Fuse Status
19
Press any of the Drive buttons located along the right side of the screen to display the same
information about another drive.
Choppers
Press Drives --> Choppers to display the Choppers Status screen.
All information on this screen is display-only. Please note that this screen may not reflect your
particular rig configuration.
Disconnect Closed
19-5
www.nov.com
19
D811001248-MAN-001
Revision 01
Page 19-6 of 14
Power System
Enable
Fuses OK
General Fault
Over Current
Rectifiers
Press Drives --> Rectifiers to display the Rectifiers Status screen.
19-6
www.nov.com
D811001248-MAN-001
Revision 01
Page 19-7 of 14
Power System
19
All information on this screen is display-only. Please note that this screen may not reflect your
particular rig configuration.
Fuses OK
Over Temperature
Disconnect Switch
Blower Running
19-7
www.nov.com
19
Power System
D811001248-MAN-001
Revision 01
Page 19-8 of 14
All information on this screen is display-only. Please note that this screen may not reflect your
particular rig configuration.
This screen provides MCC status information related to the following:
R
Mud pump blowers, liner wash, lube oil, and charge pumps
Green status displays indicate an active state; grey indicates an idle or normal state.
19-8
www.nov.com
D811001248-MAN-001
Revision 01
Page 19-9 of 14
Power System
19
Trends
Press Power System --> Trends to display the Power Trend screen.
All information on this screen is display-only. Please note that this screen may not reflect your
particular rig configuration.
This trend graph realtime online power capacity and consumed kW values.
Online status displays in the top right corner indicate the following:
R
Emg: Green indicates that the emergency generator is online; grey indicates it is
offline.
Xfmr: Green indicates that the transformer is online; grey indicates it is not.
19-9
www.nov.com
19
Power System
D811001248-MAN-001
Revision 01
Page 19-10 of 14
The Amphion power system calculates a total system capacity. Then, depending on the bus
configuration, it determines the capacity available to each individual tool.
System Capacity
When the rigs PMS sends a power available signal, the Amphion power system does not have the
data necessary to determine the exact total online capacity for the entire rig. Therefore, the
Amphion power system calculates a total power consumed value by reading the power consumed
value from each drilling tool at the drilling bus. It then calculates a system capacity value by adding
the power available value received from the rigs PMS to its calculated total power consumed
value.
(PMS) Power Available + Total Power Consumed (Drilling Bus) = System Capacity
19-10
www.nov.com
D811001248-MAN-001
Revision 01
Page 19-11 of 14
19
Power System
DC Rectifier Capacity
For most rigs, the maximum rated capacity value for each rectifier can be set using the Debug
Monitor modules powerPlant.co.maxKwAtRect file. The rectifiers default values depend on your
particular rig configuration.
The Amphion power system calculates the rectifiers individual total capacity values by using one
of the following calculated value or method:
R
By adding the consumed power value (from the rectifier) to the available power
value (from the AC Bus)
The system uses whichever value is lowest. If a rectifier is not online, its reported total capacity
value is zero.
DC Bus Capacity
The Amphion power system calculates the DC bus capacity value based on the sum of all online
rectifiers capacity values. This could be calculated using either the individual total capacity values,
or by using the sum of the individual maximum rated capacity values as described in the section
above, titled "DC Rectifier Capacity.
19-11
www.nov.com
19
Power System
D811001248-MAN-001
Revision 01
Page 19-12 of 14
DC Bus Consumed
The Amphion power system calculates the DC bus power consumed value based on the sum of all
power consumed values read from each of the tool inverters. On rigs with multiple DC buses, the
system maintains separate power consumed values for each DC bus.
AC Bus Consumed
When the Amphion power system is monitoring the status of the generators (as is normally the
case on smaller rigs) it determines the AC bus power consumed value based on the sum of the
load kW values read from each generator.
When the Amphion power system is receiving a power consumed value from a larger rigs power
management system (PMS), it uses the value provided by the PMS as the AC bus power
consumed value.
19-12
www.nov.com
D811001248-MAN-001
Revision 01
Page 19-13 of 14
19
Power System
Power Limiting
Generally speaking, if the power demands exceed the power available, the maximum power
consumption allowed for all drives is reduced simultaneously. While there is normally no
prioritization of one tool versus another (unless your rig is configured as such), power may not be
reduced proportionally between the tools consuming power. The system is designed to ensure that
there is always enough torque to hold the static load of the drawworks. In addition, power limiting is
dynamic, so all power can be diverted to a single drive if the other drives are not demanding that
power.
The motor control center (MCC) and lighting circuits are not subject to power limiting, so the power
they consume also reduces the total shared power available.
19-13
www.nov.com
19
Power System
D811001248-MAN-001
Revision 01
Page 19-14 of 14
19-14
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.20
Racker (Bridge Racker)
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-1 of 48
Operator Screen
Press <Driller or AD> Tools --> Racker to display the Bridge Racker operator screen.
Tool Ownership
Assume ownership of the racker to enable controls. See section titled "Tool Ownership" on page 234.
20-1
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-2 of 48
Fingerboards
By default, the center of the Racker operator screen displays the fingerboards. While latches are
closed, pipes in the fingerboard display as solid black circles, and contain a white number
assignment. A black number inside a white circle signifies an empty pipe slot.
Empty slots
20-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-3 of 48
20
Status Displays
The current tool mode, tool selection, operate mode, and fingerboard mode are displayed along
the top of the screen, as well as the current pipe diameter, pipe type, and pipe weight.
A graphical representation of the racker displays along the left side of the screen, illustrating the
current position and state of the roller, grip, and guide arm.
The Joystick State display located in the bottom right portion of the screen indicates the current
destination of the racker based on joystick movement and the current operation mode. See section
titled "Defining the Operation Mode" on page 20-10.
The right side of the screen contains green, yellow, red, or grey status and fault displays.
Green = Active/True
Grey = Idle
Yellow = Active/True
Grey = Idle
20-3
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-4 of 48
Tools Synchronized
Displays green when the racker and the guide arm are
synchronized.
Pin Clear
Displays green to indicate that the pin end of the tubular has
been hoisted clear of the deck, mouse hole or box at well center.
Jaw Removed
Claw Removed
ZMS Interlock
FB Comms Fault
Operator Messages
20-4
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-5 of 48
20
Press Jaw Override to open the rackers gripper jaw without pipe setdown requirements.
Press Tool Override to override the normal operating mode of the selected tool.
20-5
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-6 of 48
Backup Controls
Press the Backup Controls button located in the bottom right portion of the operator screen to
display the Backup Controls screen.
This screen allows the operator to control the tool using the on-screen controls.
R
Hoist Axis: Press and drag the red circle vertically along the Hoist Axis grid to
raise and lower the tool.
Main Joystick Display: The red circle in the Main Joystick display indicates the
current position of the joystick.
Jaws/Claw: Press Jaws/Claw - Open or Close to open or close the jaws or the
claw, depending on which tool is selected.
You can also control the jaws using the Jaws - Open/Close switch located on the
workstations left control panel.
DRIL
TDS
LINK
OPE
N
TILT
FLO
AT
TDS
CLO
SE
LINK
OPE
N
CLO
SE
OPE
N
TDS
ELE
VAT
OR
RAC
KER
OFF
/AUT
O
CLO
SE
JAW
CLO
S
DRAW
OVE WORKS
RRID
E
PAR
KIN
G BR
AKE
DOLL
Y
R AC
KER
JAW
ENA
B
LE
SLIP
SE
OPE
N
NAB
LE
CLO
SE
IBOP
20-6
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-7 of 48
20
See section titled "Jaw and Tool Override Controls" on page 20-5.
Fingerboard Controls
Press Fingerboard Controls to display the default Racker operator screen.
See section titled "Fingerboards" on page 20-2.
Park: Use to park the racker. The operator can also run the racker to jaw change
positions in Park mode.
20-7
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-8 of 48
Guide Arm: Select this option to operate the guide arm independently of the bridge
racker. This function allows the racker to tail pipe from one location to another, while
the upper end of the stand is supported by other means.
Sync: Select this option to run both the bridge racker and the guide arm in unison.
This is the default, or normal running mode.
Bridge: Select this option to operate the bridge racker independently of the guide
arm. This mode can be used to allow tripping to continue in situations where the
guide arm cannot be used to tail the lower end of the tubular.
20-8
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-9 of 48
20
Joystick Controls
A joystick mounted on the right control panel may control either the bridge racker or the
drawworks, depending on tool ownership status and your particular rig configuration.
Lower
Upper
Lower
Hoist
Dead man
switch
+Y
+X
-X
-Y
For each joystick operational function (hoist, rotate, travel, and arm movement), the degree of
joystick movement determines the speed of racker movement. For example, if you move the
joystick only slightly, the racker operates at a slow speed. If you move the joystick all the way to the
end of an axis, the racker operates at maximum speed.
Moving the racker joystick affects racker destinations, which vary depending on its current mode
(selected via the user interface) and your rig configuration. See section titled "Defining the
Operation Mode" on page 20-10.
20-9
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-10 of 48
Polar
Setback Area
Extend Arms
V-Door
Drawworks
Well Center
Traverse
Slew
Drawworks
Setback
Slew
V-Door
Arms Retract
(N/A)
(N/A)
Well Center
X/Y Override: Use this mode to allow the tool jaw to be moved in a straight line
along a designated vertical or horizontal axis.
Polar Override: Use this mode to drive the tool into a position that allows the bridge
racker to slew clockwise and counterclockwise in an arc (similar to that of an
extended guide arm).
Traverse Override: Use this mode to allow either the bridge racker, guide arm, or
both tools travel axis to be driven without any other axis. In this mode, the tools can
run only along their designated travel axis.
Press the appropriate HELP button located beneath each mode button for additional information.
Press OK to close the pop-up window and display the current modes operator screen.
20-10
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-11 of 48
20
At the Operate Mode pop-up window (see section titled "Defining the Operation Mode" on page
20-10 above), press the Manual On/Off toggle button to enable or disable manual mode.
Press OK to close the pop-up window and display the Manual Mode operator screen.
Each axis can be selected for precise positioning of the bridge racker.
Press to select an axis. A green backlight marks the current selection.
The illustration shown below depicts each axis and possible destinations based on joystick
movement and your rig configuration.
20-11
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-12 of 48
Trolley
V-Door
Drawworks
Well
Center
Fingerboard
Slew
Up
Well Center
V-Door
Drawworks
Hoist
Travel
Down
Fingerboard
Counter-clockwise (CCW)
Up
Down
CW
CCW
Clockwise (CW)
Set Mode
Press Fingerboard - Set Mode to display the Fingerboard Mode pop-up window.
Press the FB Mode - Auto, Sequence, or Manual button to select a fingerboard mode, then press
OK.
20-12
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-13 of 48
20
In Auto mode, the racker carries pipe to and from the fingerboard in pre-defined
sequences. Fingerboard latches open or close automatically as pipe is collected
from or taken to the fingerboard by the racker. (The jaw state of the racker dictates
whether the latches are opened or closed.)
In Sequence mode, the racker carries pipe to and from the fingerboard in predefined sequences (as in Auto mode), but the operator controls the opening and
closing of the latches by pressing the Activate button on the screen. (The jaw state
of the racker dictates whether the latches are opened or closed.)
In Manual mode, the operator manually selects the fingerboard slots and controls
the opening and closing of the latches. Automatic movement of the racker is
prohibited in this mode.
Set Begin/End
Press Fingerboard - Set Begin/End to display the Set Fingerboard Begin/End pop-up window.
Use this pop-up window to set the range of fingerboard slots for the racker to use when racking
pipe.
Press the appropriate button to display its keypad pop-up window.
Define the value, then press Set to confirm and close the keypad.
Press OK to close the Set Fingerboard Begin/End pop-up window.
20-13
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-14 of 48
Press the Pipe Type - Pipe, Collar, or Casing button to select the appropriate pipe type, then
press OK to close the pop-up window.
20-14
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-15 of 48
20
Define the weight value of the tubular to be handled, then press Set to confirm and close the
keypad.
!
The value entered here must be accurate, as the system
uses this weight value to calculate thread compensation.
20-15
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-16 of 48
20-16
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-17 of 48
20
Setup Menu
Press Racker --> Setup to display the Setup menu.
20-17
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-18 of 48
Axis Calibration
At the Maintenance Mode and Calibration screen, press Axis Calibration to display the main
Axis Calibration screen.
Press to select an axis, then follow screen prompts to calibrate the racker.
20-18
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-19 of 48
20
2. Move the bridge racker to its calibration point, then press Next to write the
calibration values to the tool controller and display the second calibration screen.
3. Move the bridge racker to ensure that it is operating properly, then press Finish.
Bridge racker trolley calibration is complete.
20-19
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-20 of 48
2. Move the bridge racker to its calibration point, then press Next to write the
calibration values to the tool controller and display the second calibration screen.
3. Move the bridge racker to ensure that it is operating properly, then press Finish.
Bridge racker aft traverse calibration is complete.
20-20
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-21 of 48
20
2. Move the bridge racker to its calibration point, then press Next to write the
calibration values to the tool controller and display the second calibration screen.
3. Move the bridge racker to ensure that it is operating properly, then press Finish.
Bridge racker fore traverse calibration is complete.
20-21
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-22 of 48
2. Rotate the bridge racker to its calibration point, then press Next to write the
calibration values to the tool controller and display the second calibration screen.
3. Rotate the bridge racker to ensure that it is operating properly, then press Finish.
Bridge racker slew calibration is complete.
20-22
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-23 of 48
20
2. Move the bridge racker to its calibration point, then press Next to write the
calibration values to the tool controller and display the second calibration screen.
3. Move the bridge racker to ensure that it is operating properly, then press Finish.
Bridge racker hoist calibration is complete.
20-23
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-24 of 48
2. Move the bridge racker to its calibration point, then press Next to write the
calibration values to the tool controller and display the second calibration screen.
3. Move the bridge racker to ensure that it is operating properly, then press Finish.
Thread compensation cylinder calibration is complete.
20-24
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-25 of 48
20
2. Move the bridge racker to its calibration point, then press Next to write the
calibration values to the tool controller and display the second calibration screen.
3. Move the bridge racker to ensure that it is operating properly, then press Finish.
Guide arm trolley calibration is complete.
20-25
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-26 of 48
2. Rotate the bridge racker to its calibration point, then press Next to write the
calibration values to the tool controller and display the second calibration screen.
3. Rotate the bridge racker to ensure that it is operating properly, then press Finish.
Guide arm shoulder calibration is complete.
20-26
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-27 of 48
20
2. Move the bridge racker to its calibration point, then press Next to write the
calibration values to the tool controller and display the second calibration screen.
3. Move the bridge racker to ensure that it is operating properly, then press Finish.
Guide arm wrist calibration is complete.
20-27
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-28 of 48
2. Rotate the bridge racker to its calibration point, then press Next to write the
calibration values to the tool controller and display the second calibration screen.
3. Rotate the bridge racker to ensure that it is operating properly, then press Finish.
Guide arm slew calibration is complete.
20-28
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-29 of 48
20
2. Move the bridge racker to its calibration point, then press Next to write the
calibration values to the tool controller and display the second calibration screen.
3. Move the bridge racker to ensure that it is operating properly, then press Finish.
Guide arm telescope calibration is complete.
20-29
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-30 of 48
At the Maintenance Mode and Calibration screen, press Bridge Racker to display the main
Bridge Racker Calibration screen.
!
A red Low Hydraulic Pressure display indicates that
hydraulic pressure has fallen below an acceptable level.
Correct the situation before continuing calibration
procedures.
The center portion of the screen depicts the current position of the joystick, and related racker
destinations. See section titled "Defining the Operation Mode" on page 20-10 for information about
joystick movement and racker destinations as it relates to the currently-selected operation mode.
Press the rackers Jaw - (Open or Close) button to control the racker jaws. See section titled "Jaw
and Tool Override Controls" on page 20-5 for more information. Select an axis to begin calibration.
20-30
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-31 of 48
20
Trolley
At the Bridge Racker Calibration screen, press the Select Axis - Trolley button display the
Trolley Calibration screen.
The current Trolley Position displays in the top left portion of the screen.
The center portion of the screen depicts the current position of the joystick, and related racker
destinations. See section titled "Defining the Operation Mode" on page 20-10 for information about
joystick movement and racker destinations as it relates to the currently-selected operation mode.
Press the rackers Jaw - (Open or Close) button to control the racker jaws. See section titled "Jaw
and Tool Override Controls" on page 20-5 for more information.
1. Ensure that the correct pipe type is defined. See section titled "Defining the Pipe
Type" on page 20-14.
2. Ensure that the correct tubular diameter is set. See section titled "Defining the Pipe
Diameter" on page 20-14.
3. Using the joystick, move the racker toward each possible destination, ensuring that
the racker is operating properly.
Press Main Page to return to the main Maintenance Mode and Calibration screen.
20-31
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-32 of 48
Travel
At the Bridge Racker Calibration screen, press the Select Axis - Travel button display the
Travel Calibration screen.
The top left portion of the screen contains displays of the current positions for both the Fore and
the Aft Bridge.
The center portion of the screen depicts the current position of the joystick, and related racker
destinations. See section titled "Defining the Operation Mode" on page 20-10 for information about
joystick movement and racker destinations as it relates to the currently-selected operation mode.
Press the rackers Jaw - (Open or Close) button to control the racker jaws. See section titled "Jaw
and Tool Override Controls" on page 20-5 for more information.
1. Ensure that the correct pipe type is defined. See section titled "Defining the Pipe
Type" on page 20-14.
2. Ensure that the correct tubular diameter is set. See section titled "Defining the Pipe
Diameter" on page 20-14.
3. Press and hold one of the Travel Override Mode buttons
4. Using the joystick, move the racker toward each possible destination, ensuring that
the racker is operating properly.
5. Repeat this procedure using each of the Travel Override Modes.
Press Main Page to return to the main Maintenance Mode and Calibration screen.
20-32
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-33 of 48
20
Hoist
At the Bridge Racker Calibration screen, press the Select Axis - Hoist button display the Hoist
Calibration screen.
The top left portion of the screen displays the current Hoist Position.
The center portion of the screen depicts the current position of the joystick, and related racker
destinations. See section titled "Defining the Operation Mode" on page 20-10 for information about
joystick movement and racker destinations as it relates to the currently-selected operation mode.
Press the rackers Jaw - (Open or Close) button to control the racker jaws. See section titled "Jaw
and Tool Override Controls" on page 20-5 for more information.
1. Ensure that the correct pipe type is defined. See section titled "Defining the Pipe
Type" on page 20-14.
2. Ensure that the correct tubular diameter is set. See section titled "Defining the Pipe
Diameter" on page 20-14.
3. Using the joystick, move the racker toward each possible destination, ensuring that
the racker is operating properly.
Press Main Page to return to the main Maintenance Mode and Calibration screen.
20-33
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-34 of 48
Slew
At the Bridge Racker Calibration screen, press the Select Axis - Slew button display the Slew
Calibration screen.
The top left portion of the screen displays the current Slew Position.
The center portion of the screen depicts the current position of the joystick, and related racker
destinations. See section titled "Defining the Operation Mode" on page 20-10 for information about
joystick movement and racker destinations as it relates to the currently-selected operation mode.
Press the rackers Jaw - (Open or Close) button to control the racker jaws. See section titled "Jaw
and Tool Override Controls" on page 20-5 for more information.
1. Ensure that the correct pipe type is defined. See section titled "Defining the Pipe
Type" on page 20-14.
2. Ensure that the correct tubular diameter is set. See section titled "Defining the Pipe
Diameter" on page 20-14.
3. Rotating the joystick, move the racker toward each possible destination, ensuring
that the racker is operating properly.
Press Main Page to return to the main Maintenance Mode and Calibration screen.
20-34
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-35 of 48
20
!
A red Low Hydraulic Pressure display indicates that
hydraulic pressure has fallen below an acceptable level.
Correct the situation before continuing calibration
procedures.
The center portion of the screen depicts the current position of the joystick, and related racker
destinations. See section titled "Defining the Operation Mode" on page 20-10 for information about
joystick movement and racker destinations as it relates to the currently-selected operation mode.
Press the rackers Jaw - (Open or Close) button to control the racker jaws. See section titled "Jaw
and Tool Override Controls" on page 20-5 for more information.
The center portion of the screen depicts the current position of the joystick, and related racker
destinations. See section titled "Defining the Operation Mode" on page 20-10 for information about
joystick movement and racker destinations as it relates to the currently-selected operation mode.
Press the rackers Jaw - (Open or Close) button to control the racker jaws. See section titled "Jaw
and Tool Override Controls" on page 20-5 for more information.
Select an axis to begin calibration.
20-35
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-36 of 48
Traverse
At the Guide Arm Calibration screen, press Traverse to display the Traverse Calibration
screen.
The top left portion of the screen displays the current Trolley Position.
The center portion of the screen depicts the current position of the joystick, and related racker
destinations. See section titled "Defining the Operation Mode" on page 20-10 for information about
joystick movement and racker destinations as it relates to the currently-selected axis.
Press the rackers Jaw - (Open or Close) button to control the racker jaws. See section titled "Jaw
and Tool Override Controls" on page 20-5 for more information.
1. Ensure that the correct pipe type is defined. See section titled "Defining the Pipe
Type" on page 20-14.
2. Ensure that the correct tubular diameter is set. See section titled "Defining the Pipe
Diameter" on page 20-14.
3. Using the joystick, move the guide arm toward each possible destination, ensuring
that it is operating properly.
Press Main Page to return to the main Maintenance Mode and Calibration screen.
20-36
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-37 of 48
20
Slew
At the Guide Arm Calibration screen, press Slew to display the Slew Calibration screen.
The top left portion of the screen displays the current Slew Position.
The center portion of the screen depicts the current position of the joystick, and related racker
destinations. See section titled "Defining the Operation Mode" on page 20-10 for information about
joystick movement and racker destinations as it relates to the currently-selected operation mode.
Press the rackers Jaw - (Open or Close) button to control the racker jaws. See section titled "Jaw
and Tool Override Controls" on page 20-5 for more information.
1. Ensure that the correct pipe type is defined. See section titled "Defining the Pipe
Type" on page 20-14.
2. Ensure that the correct tubular diameter is set. See section titled "Defining the Pipe
Diameter" on page 20-14.
3. Rotating the joystick through its full range of motion, move the guide arm toward
each possible destination, ensuring that it is operating properly.
Press Main Page to return to the main Maintenance Mode and Calibration screen.
20-37
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-38 of 48
Shoulder
At the Guide Arm Calibration screen, press Shoulder to display the Shoulder Calibration
screen.
The top left portion of the screen displays the current Shoulder Angle.
The center portion of the screen depicts the current position of the joystick, and related racker
destinations. See section titled "Defining the Operation Mode" on page 20-10 for information about
joystick movement and racker destinations as it relates to the currently-selected operation mode.
Press the rackers Jaw - (Open or Close) button to control the racker jaws. See section titled "Jaw
and Tool Override Controls" on page 20-5 for more information.
1. Ensure that the correct pipe type is defined. See section titled "Defining the Pipe
Type" on page 20-14.
2. Ensure that the correct tubular diameter is set. See section titled "Defining the Pipe
Diameter" on page 20-14.
3. Using the joystick, move the guide arm toward each possible destination, ensuring
that it is operating properly.
Press Main Page to return to the main Maintenance Mode and Calibration screen.
20-38
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-39 of 48
20
Telescope
At the Guide Arm Calibration screen, press Telescope to display the Telescope Calibration
screen.
The top left portion of the screen displays the current Telescope position.
The center portion of the screen depicts the current position of the joystick, and related racker
destinations. See section titled "Defining the Operation Mode" on page 20-10 for information about
joystick movement and racker destinations as it relates to the currently-selected operation mode.
Press the rackers Jaw - (Open or Close) button to control the racker jaws. See section titled "Jaw
and Tool Override Controls" on page 20-5 for more information.
1. Ensure that the correct pipe type is defined. See section titled "Defining the Pipe
Type" on page 20-14.
2. Ensure that the correct tubular diameter is set. See section titled "Defining the Pipe
Diameter" on page 20-14.
3. Using the joystick, move the guide arm toward each possible destination, ensuring
that it is operating properly.
Press Main Page to return to the main Maintenance Mode and Calibration screen.
20-39
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-40 of 48
Wrist
At the Guide Arm Calibration screen, press Wrist to display the Wrist Calibration screen.
The top left portion of the screen displays the current Wrist position.
The center portion of the screen depicts the current position of the joystick, and related racker
destinations. See section titled "Defining the Operation Mode" on page 20-10 for information about
joystick movement and racker destinations as it relates to the currently-selected operation mode.
Press the rackers Jaw - (Open or Close) button to control the racker jaws. See section titled "Jaw
and Tool Override Controls" on page 20-5 for more information.
1. Ensure that the correct pipe type is defined. See section titled "Defining the Pipe
Type" on page 20-14.
2. Ensure that the correct tubular diameter is set. See section titled "Defining the Pipe
Diameter" on page 20-14.
3. Using the joystick, move the guide arm toward each possible destination, ensuring
that it is operating properly.
Press Main Page to return to the main Maintenance Mode and Calibration screen.
20-40
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-41 of 48
20
ATOS Calibration
At the Maintenance Mode and Calibration screen, press ATOS Calibration to display the
Bridge Racker ATOS Calibration screen.
20-41
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-42 of 48
20-42
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-43 of 48
20
Thread Comp
At the ATOS Calibration screen, press Thread Comp to display the Thread Comp ATOS
Calibration screen.
20-43
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-44 of 48
20-44
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-45 of 48
20
20-45
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-46 of 48
20-46
www.nov.com
D811001248-MAN-001
Revision 01
Page 20-47 of 48
20
!
Use extreme caution during calibration. This mode adjusts
pressure to the thread compensation hydraulic circuits.
Hoist the carriage while using the controls described in this
section.
Press Setup --> Thread Comp Calibration to display the Thread Compensation Calibration
screen.
Press Bypass Valve Control - Open or Close to open or close the bypass valve.
Perform the following steps for thread compensation calibration:
1. Press Maintenance Mode - On to enable maintenance mode.
2. Press On to enable (Pressure or Position) PID Setup.
3. Press and move each slider control to the desired percentage value.
4. Press Off to disable (Pressure or Position) PID Setup
5. Press Maintenance Mode - Off to disable maintenance mode.
20-47
www.nov.com
20
D811001248-MAN-001
Revision 01
Page 20-48 of 48
This screen displays digital readings and vertical graphs that depict the current position of the
bridge racker and guide arm axes. It also displays pressure readings and setpoint information.
20-48
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.21
Racker (Pipe Racking System PRS)
www.nov.com
D811001248-MAN-001
Revision 01
Page 21-1 of 14
Operator Screen
Press <Driller or AD> Tools --> Racker to display the Pipe Racking System (PRS) operator
screen.
Tool Ownership
Assume ownership of the racker to enable controls. See section titled "Tool Ownership" on page 234.
21-1
www.nov.com
21
D811001248-MAN-001
Revision 01
Page 21-2 of 14
Status Displays
A graphical representation of the racker displays along the left side of the screen, illustrating the
current state of the jaws and the hoist and tail claws (several examples are shown here).
The currently-selected racker and fingerboard modes, tubular options, joystick status, and tubular
lengths display along the top of the screen.
A yellow Pipe Setdown display indicates the racker has reached pipe setdown; grey indicates that
the pipe is not on the floor.
Green communication status displays (Comms Healthy) indicate healthy communications; red
indicates a fault or alarm state.
21-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 21-3 of 14
21
Fingerboards
By default, the center of the Racker screen displays the fingerboards. Press the Fingerboards
button at any time to display them again.
While latches are closed, pipes in the fingerboard display as solid black circles, and contain a
white number assignment. A black number inside a white circle with a black outline signifies an
empty pipe slot.
21-3
www.nov.com
21
D811001248-MAN-001
Revision 01
Page 21-4 of 14
Press anywhere outside of the zoomed in fingerboard area to return to the default Fingerboard/
Racker screen.
21-4
www.nov.com
D811001248-MAN-001
Revision 01
Page 21-5 of 14
21
Fingerboard Options
Press the Fingerboard Options button (located along the right side of the racker screen) to
display the controls shown here.
Fingerboard Mode
Press the Fingerboard Mode - Auto, Manual, or Sequence button to select a fingerboard mode.
R
In Auto mode, the racker carries pipe to and from the fingerboard in pre-defined
sequences. Fingerboard latches open or close automatically as pipe is collected
from or taken to the fingerboard by the racker. (The jaw state dictates whether the
latches are opened or closed.)
In Manual mode, the operator manually selects the fingerboard slots and controls
latch opening and closing. Automatic movement of the racker is prohibited in this
mode.
In Sequence mode, the racker carries pipe to and from the fingerboard in predefined sequences (as in Auto mode), but the operator controls latch opening and
closing. (The jaw state dictates whether the latches are opened or closed.)
21-5
www.nov.com
21
D811001248-MAN-001
Revision 01
Page 21-6 of 14
Racker Options
Press the Racker Options button to display the controls shown here.
Racker Modes
This section contains general information about racker modes. For more detailed information, see
the model-specific document titled Pipe Racking System Service Manual.
Press any of the Racker Mode buttons to select a mode:
R
Parking: Use to park the racker; the operator can also run the racker to jaw change
positions in Park mode.
Foxhole Selection
Press to select Foxhole A or Foxhole B.
A green backlight marks the current selection.
21-6
www.nov.com
D811001248-MAN-001
Revision 01
Page 21-7 of 14
21
Well/Foxhole Teach
Press the Well/Foxhole Teach button when the racker is positioned at well center or the foxhole to
teach the racker its arm rotation and current destination.
Jaw Override
Press and hold the Jaw Override button to override jaw safety interlocks.
When the racker is gripping a pipe, the claw and grip are both closed. The grip will not open unless
either another operator gives permission, or the operator presses the Jaw Override button. The
grip will also remain open when tubular mode is set to Collar or Casing.
When the button is released, the tool returns to normal operating mode.
21-7
www.nov.com
21
D811001248-MAN-001
Revision 01
Page 21-8 of 14
Tubular Options
Press the Tubular Option button to display the controls shown here.
Pipe Selection
Press Tubular Options - Pipe, Collar, or Casing to define the type of tubulars being handled. A
green backlight marks the current selection.
Read from Conveyor: Use this option to allow the pipe transfer conveyor sensors
automatically calculate the pipe length.
Manually Input: Use this option to display the keypad pop-up window and manually
define the pipe length value. Press Set to confirm the value and close the keypad.
21-8
www.nov.com
D811001248-MAN-001
Revision 01
Page 21-9 of 14
21
Lower
Lower
Hoist
Dead man
switch
+Y
+X
-X
-Y
For each joystick operational function (hoist, lower, travel, and arm movement), the degree of
joystick movement determines the speed of racker movement. For example, if you move the
joystick only slightly, the racker operates at a slow speed. If you move the joystick all the way to the
end of an axis, the racker operates at maximum speed.
The destination of the racker depends upon the racker mode selection. See section titled "Racker
Modes" on page 21-6. Any movement of the joystick drives the racker toward the pre-programmed
path of the selected section.
Press the Joystick Help button to display the current destination of the racker through use of the
joystick.
The screen shown above depicts possible racker destinations (using the joystick) while in Stands
mode. The illustration below here depicts additional racker modes and possible destinations.
Tripping
Stands
Singles
Parking
Fingerboard
Fingerboard
(N/A)
(N/A)
(N/A)
(N/A)
Well Center
Pick Up
Null
Foxhole
Pick Up
(N/A)
Well Center
Park
(N/A)
(N/A)
21-9
www.nov.com
21
D811001248-MAN-001
Revision 01
Page 21-10 of 14
21-10
www.nov.com
D811001248-MAN-001
Revision 01
Page 21-11 of 14
21
Calibration
Press Racker --> Calibration to display the first Racker Calibration screen.
Press to select an axis to calibrate, then follow screen prompts to calibrate the racker.
21-11
www.nov.com
21
D811001248-MAN-001
Revision 01
Page 21-12 of 14
Press and hold the Racker X/Y Override button (normally located on the operator workstations
left control panel) to override the X/Y interlocks.
OFF
/AUT
O
ON
OPE
CLO
SE
TDS
B
OPE
N
TDS
RAK
E
TDS
FLO
AT
CLO
SE
DRIL
POW
ER S
TILT
OPE
LIPS
CLO
SE
IBOP
TDS
LINK
TDS
OPE
N
ELE
VAT
OR
CLO
SE
RAC
KER
X
OVE /Y
RRID
E
OFF
/AUT
O
PAR
KIN
G BR
RAC
K
TRA ER
OVE VEL
RRID
E
ON
RAC
KE
JAW R
S
AKE
A
OVE DS
RRID
E
RAC
KER
X
OVE /Y
RRID
E
When the button is released, the tool returns to normal operating mode.
21-12
www.nov.com
D811001248-MAN-001
Revision 01
Page 21-13 of 14
21
Press and hold the Racker Travel Override button (normally located on the operator workstations
left control panel) to override the racker travel interlocks.
OFF
/AUT
O
ON
OPE
CLO
SE
TDS
B
OPE
TDS
RAK
E
TDS
FLO
AT
CLO
SE
DRIL
POW
ER S
TILT
OPE
LIPS
CLO
SE
IBOP
TDS
LINK
TDS
OPE
N
ELE
VAT
OR
CLO
SE
RAC
KER
X
OVE /Y
RRID
E
OFF
/AUT
O
PAR
K
ING
BR A
RAC
K
TRA ER
OVE VEL
RRID
E
ON
RAC
KE
JAW R
S
KE
A
OVE DS
RRID
E
RAC
K
TRA ER
OVE VEL
RRID
E
When the button is released, the tool returns to normal operating mode.
21-13
www.nov.com
21
D811001248-MAN-001
Revision 01
Page 21-14 of 14
21-14
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.22
Rotary Table
www.nov.com
D811001248-MAN-001
Revision 01
Page 22-1 of 8
Rotary Table
Operator Screen
Press <Driller or AD> Tools --> Rotary Table to display the Rotary Table operator screen.
Tool Ownership
Assume ownership of the rotary table to enable controls. See section titled "Tool Ownership" on
page 2-34.
22-1
www.nov.com
22
D811001248-MAN-001
Revision 01
Page 22-2 of 8
Rotary Table
Status Displays
The left side of the operator screen contains realtime speed and torque graphs that reflect their
current values. Black markers indicate user-defined setpoint values.
Additional status and alarm information displays to the right of the graphs. (See general
descriptions below.)
Also see section titled "Speed and Torque Controls" on page 22-4.
Red indicates that the grease level has fallen below an acceptable
level.
RST Locked
Maint Mode
22-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 22-3 of 8
Rotary Table
22
Direction Controls
Press CCW (counter-clockwise) or CW (clockwise) to define the rotary table direction.
Lock Controls
Press Unlock or Lock to release or lock the rotary table.
!
Although engaging the lock prevents the RST from turning,
it may move slightly until the lock is secure.
22-3
www.nov.com
22
Rotary Table
D811001248-MAN-001
Revision 01
Page 22-4 of 8
Define the maximum speed value, then press Set to confirm the value and close the keypad.
Use the blue arrow up or down buttons to incrementally adjust the value as needed.
Zero Throttle
Press Zero Throttle to slowly reduce the speed of the rotary table to zero rpm.
Define the maximum torque setpoint value, then press Set to confirm the value and close the
keypad.
Use the blue arrow up or down keys to incrementally adjust the value as needed.
22-4
www.nov.com
D811001248-MAN-001
Revision 01
Page 22-5 of 8
Rotary Table
22
22-5
www.nov.com
22
D811001248-MAN-001
Revision 01
Page 22-6 of 8
Rotary Table
Calibration
Press Rotary Table --> Calibration to display the Rotary Table Calibration screen.
!
Ensure that the power slips are powered off, and remain so
during this procedure, and that the load cell and lever arm
can withstand 45,000 ft.-lbs. of pressure.
22-6
www.nov.com
D811001248-MAN-001
Revision 01
Page 22-7 of 8
Rotary Table
22
5. Press the Torque Arm Length - Change or Number of Points - Change button if
necessary to display their keypad.
22-7
www.nov.com
22
D811001248-MAN-001
Revision 01
Page 22-8 of 8
Rotary Table
6. Define the correct value, then press Set to confirm the value and close the keypad.
7. Press Next Step, then follow the remaining screen prompts to complete the
calibration process for the clockwise (CW) direction.
!
This calibration procedure must be performed in each
direction (clockwise and counter-clockwise).
8. Once the CW calibration is complete, rig the load cell for counter-clockwise (CCW)
calibration.
9. Follow the same procedure to calibrate the CCW direction using the second
calibration screen (shown on page 22-7).
22-8
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.23
Roughneck
www.nov.com
D811001248-MAN-001
Revision 01
Page 23-1 of 28
Roughneck
Operator Screen
Press <Driller or AD> Tools --> Roughneck to display the Automated Roughneck operator
screen.
Tool Ownership
Assume ownership of the roughneck to enable controls. See section titled "Tool Ownership" on
page 2-34.
23-1
www.nov.com
23
Roughneck
D811001248-MAN-001
Revision 01
Page 23-2 of 28
Tool On
E-Stop
Hydraulic
Pressure Low
Torque Gauge
and Setpoint
The torque gauge located in the top left corner of the screen displays the
current torque reading. A blue marker on the gauge and a digital reading
located directly below the gauge indicate the user-defined torque
setpoint value. You can change the torque setpoint value incrementally
by pressing the blue arrow up or down buttons. See section titled
"Defining a Torque Setpoint Value" on page 23-12.
Tool Joint
Length
Displays the current user-defined tool joint length value. See section
titled "Defining the Tool Joint Length" on page 23-13 for information about
changing the value.
Maintenance
Mode
Tool Interlock
ZMS Interlock
Slow Mode
Displays green when slow mode is active. See section titled "Slow Mode
Controls" on page 23-13.
Power Slips
Mode
Displays green when power slips mode is active. See section titled
"Power Slip Mode Controls" on page 23-14.
Tool Mode
Well/Foxhole
Selection
23-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 23-3 of 28
Roughneck
23
Press the SW Carriage - Up or Down buttons to control the spin wrench carriage as needed.
The red circle represents the current position of the virtual joystick. Touch and drag horizontally
along the grid to travel the roughneck forward or reverse (toward the well center or toward a park
position). Touch and drag vertically to hoist or lower the main carriage.
Use the blue arrow down or arrow up buttons to incrementally adjust the roughnecks joystick scale
multiplier value. This value determines the virtual joysticks sensitivity.
See section titled "Travel Controls" on page 23-4, and section titled "Torque Wrench Carriage
Controls" on page 23-10.
Press Save to store the joystick settings.
Press Help to display the Joystick Help screen.
23-3
www.nov.com
23
D811001248-MAN-001
Revision 01
Page 23-4 of 28
Roughneck
Travel Controls
Depending on your roughneck model and your rig configuration, you may be able to define the
travel direction by using the AR Travel - Well or Back discrete switch, normally located on the
operator workstations right control panel.
BREA
OUT
E
MAK
IN
N
DOW
UP
RQUE
AR TO
IN
AR SP
CLOS
GE
RRIA
TW CA
CLOS
ACK
WEL
WEL
BACK
OPEN
OPEN
AR TW
AR SW
AR TR
EL
AV
R TR
AVEL
TOOL P
RSHI
OWNE E ALL
AS
RELE
S
SLIP
LE P/
ENAB EVATOR
BX EL
23-4
www.nov.com
D811001248-MAN-001
Revision 01
Page 23-5 of 28
Roughneck
23
OOR
L FL
DRIL IPMENT
EQU TOP
E-S
PUS
H TO
P
STO
TDS
P
RT R
O
AUT
AR - ENCE
U
SEQ
O
AUT
AR - ENCE
U
SEQ
See the product-specific Automated Roughneck Service Manual for more information about
automatic sequence mode.
23-5
www.nov.com
23
Roughneck
D811001248-MAN-001
Revision 01
Page 23-6 of 28
Override Controls
Press and hold the Override button to enable the roughneck override.
Override mode reduces the roughnecks operation speed to 50% of its maximum, and allows it to
travel beyond its normal limits.
See Chapter 27, titled "Zone Management System (ZMS) for more information about tool
overrides.
23-6
www.nov.com
D811001248-MAN-001
Revision 01
Page 23-7 of 28
Roughneck
23
MAK
BREA
OUT
IN
N
DOW
UP
RQUE
AR TO
AR SP
TW
IN
E
CLOS
IAGE
CARR
E
CLOS
CLO
SE
L
WEL
BACK
OPEN
OPEN
AR TW
OPE
AR SW
AR TR
AVEL
TOOL P
RSHI
OWNE E ALL
AS
RELE
AR S
S
SLIP
LE P/
ENAB EVATOR
BX EL
23-7
www.nov.com
23
D811001248-MAN-001
Revision 01
Page 23-8 of 28
Roughneck
BREA
OUT
OUT
MAK
IN
N
DOW
UP
RQUE
AR TO
IN
AR SP
TW CA
IN
E
CLOS
GE
RRIA
E
CLOS
L
WEL
BACK
OPEN
OPEN
AR TW
PIN
AR S
AR SW
AR
EL
TRAV
TOOL P
RSHI
OWNE E ALL
AS
RELE
S
SLIP
LE P/
ENAB EVATOR
BX EL
23-8
www.nov.com
D811001248-MAN-001
Revision 01
Page 23-9 of 28
Roughneck
23
OUT
MAK
BREA
IN
N
DOW
UP
RQUE
AR TO
AR SP
TW
IN
E
CLOS
IAGE
CARR
E
CLOS
SE
CLO
L
WEL
BACK
OPEN
OPEN
AR TW
N
OPE
AR SW
AVEL
AR TR
TOOL P
RSHI
OWNE E ALL
AS
RELE
W
AR T
S
SLIP
LE P/
ENAB EVATOR
BX EL
23-9
www.nov.com
23
D811001248-MAN-001
Revision 01
Page 23-10 of 28
Roughneck
BREA
OUT
N
DOW
E
MAK
IN
N
DOW
UP
UP
RQUE
AR TO
IN
AR SP
CLOS
GE
RRIA
TW CA
WEL
E
CLOS
BACK
AR TW
GE
RRIA
AR SW
TW C
OPEN
OPEN
AR TR
AVEL
TOOL P
RSHI
OWNE E ALL
AS
RELE
S
SLIP
LE P/
ENAB EVATOR
BX EL
23-10
www.nov.com
D811001248-MAN-001
Revision 01
Page 23-11 of 28
23
Roughneck
OUT
E
MAK
AK
MAK
BREA
IN
N
DOW
UP
BRE
RQUE
AR TO
AR SP
TW CA
IN
E
CLOS
GE
RRIA
E
CLOS
L
WEL
BACK
AR TW
AR
OPEN
OPEN
QU
TOR
AR SW
AR TR
AVEL
TOOL P
RSHI
OWNE E ALL
AS
RELE
S
SLIP
LE P/
ENAB EVATOR
BX EL
23-11
www.nov.com
23
Roughneck
D811001248-MAN-001
Revision 01
Page 23-12 of 28
23-12
www.nov.com
D811001248-MAN-001
Revision 01
Page 23-13 of 28
Roughneck
23
Define a new value, then press Set to confirm and close the keypad.
Use the blue arrow up and down buttons to incrementally adjust the value.
Define a new value, then press Set to confirm and close the keypad.
Use the blue arrow up or down buttons to incrementally adjust the value.
23-13
www.nov.com
23
Roughneck
D811001248-MAN-001
Revision 01
Page 23-14 of 28
Roughneck Modes
Press to select a mode (see general descriptions below).
23-14
www.nov.com
D811001248-MAN-001
Revision 01
Page 23-15 of 28
Roughneck
SW Backup: Select this mode to use the torque wrench as the spinning wrench
backup. This mode is normally used at the foxhole, or when manual slips are used.
TDS Backup: Select this mode to designate the torque wrench as the top drive
backup.
Bit Break: Select this mode to use the bit break wrench instead of the torque
wrench.
Mud Bucket: Use Mud Bucket Mode to communicate whether or not the mud
buckets are present (On = present, Off = not present).
23
The currently-selected tool mode displays along the top of the screen, and also displays on the
main operator screen.
Well/Foxhole Selection
Press to select a well and foxhole option.
23-15
www.nov.com
23
Roughneck
D811001248-MAN-001
Revision 01
Page 23-16 of 28
Roughneck Status
Press the Status button to display the Roughneck Position Status screen.
Green displays indicate an active state or mode for the clamps, torque wrench, spin wrench clamp,
and spin wrench direction.
Digital readings display the current position of the roughneck (traverse), main carriage, spin
wrench carriage, torque, and clamp.
Press Close to return to the Roughneck operator screen.
23-16
www.nov.com
D811001248-MAN-001
Revision 01
Page 23-17 of 28
Roughneck
23
23-17
www.nov.com
23
Roughneck
D811001248-MAN-001
Revision 01
Page 23-18 of 28
Calibration
Press Roughneck --> Calibration to display the default Roughneck Calibration screen.
Press to select an axis, then follow screen prompts to calibrate the roughneck.
23-18
www.nov.com
D811001248-MAN-001
Revision 01
Page 23-19 of 28
23
Roughneck
Positions Setup
!
Calibrate the roughneck prior to performing positions
setup.
Press Roughneck --> Setup to display the Roughneck Positions Setup screen.
Press to select a position from the left side of the screen (see initial screens for each position on
the following pages), then follow screen prompts to complete each position setup.
23-19
www.nov.com
23
Roughneck
D811001248-MAN-001
Revision 01
Page 23-20 of 28
23-20
www.nov.com
D811001248-MAN-001
Revision 01
Page 23-21 of 28
23
Roughneck
All Well Center and Foxhole setup screens offer the option to change the assigned names. Press
Change Name to display the alpha-numeric keypad.
Define the name, then press Enter to close the keypad and return to the previous screen.
Foxhole
23-21
www.nov.com
23
Roughneck
D811001248-MAN-001
Revision 01
Page 23-22 of 28
23-22
www.nov.com
D811001248-MAN-001
Revision 01
Page 23-23 of 28
Roughneck
23
23-23
www.nov.com
23
Roughneck
D811001248-MAN-001
Revision 01
Page 23-24 of 28
23-24
www.nov.com
D811001248-MAN-001
Revision 01
Page 23-25 of 28
Roughneck
23
Duck Height
Mud Bucket
23-25
www.nov.com
23
Roughneck
D811001248-MAN-001
Revision 01
Page 23-26 of 28
Bit Breaker
23-26
www.nov.com
D811001248-MAN-001
Revision 01
Page 23-27 of 28
Roughneck
23
23-27
www.nov.com
23
Roughneck
D811001248-MAN-001
Revision 01
Page 23-28 of 28
23-28
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.24
S-DAQ
www.nov.com
D811001248-MAN-0001
Revision 01
Page 24-1 of 8
S-DAQ
Operator Screen
Press <Driller or AD> Tools --> S-DAQ to display the S-DAQ operator screen.
24-1
www.nov.com
24
D811001248-MAN-0001
Revision 01
Page 24-2 of 8
S-DAQ
Standpipe Pressure
The analog gauge contains a digital and graphical display of the current standpipe pressure (SPP)
reading. The red needle moves along the outer edge of the gauge to point to the current pressure.
24-2
www.nov.com
D811001248-MAN-0001
Revision 01
Page 24-3 of 8
S-DAQ
24
Cumulative stroke counts display along the bottom of the screen (beneath the average SPM
graphs) for all enabled pumps combined and individually.
Alarm Displays
Depending on your rig configuration, you may be able to set up alarms for many gauges, graphs,
or readings displayed on the S-DAQ screens.
The background of the digital readings or graph display red if the preset value reaches the highhigh range or the low-low range.
The background displays yellow if the preset value reaches the high or low range.
Digital Readings
R
A small red rectangle in the bottom right corner of the display indicates that an alarm
trigger for a high-high value has been set.
A small yellow rectangle in the bottom right corner of the display indicates that an
alarm trigger for a high value has been set.
A small yellow rectangle in the bottom left of corner of the display indicates that an
alarm trigger for a low value has been set.
A small red rectangle in the bottom left corner indicates that an alarm trigger for a
low-low value has been set.
Graphs
R
Red markers along the top side of the graphs indicate the preset high-high range
alarm, and where the high-high alarm will be triggered.
24-3
www.nov.com
24
S-DAQ
D811001248-MAN-0001
Revision 01
Page 24-4 of 8
Yellow markers along the top side of the graphs indicate the preset high range
alarm, and where the high alarm will be triggered.
Yellow markers along the bottom side of the graphs indicates the preset low range
alarm, and where the low alarm will be triggered.
Red markers along the bottom side of the graphs indicate the preset low-low range
alarm, and where the low-low alarm will be triggered.
24-4
www.nov.com
D811001248-MAN-0001
Revision 01
Page 24-5 of 8
S-DAQ
24
S-DAQ Menu
Press the S-DAQ button to display its tool menu.
24-5
www.nov.com
24
S-DAQ
D811001248-MAN-0001
Revision 01
Page 24-6 of 8
Mud Pits
Shaker Tanks
Press S-DAQ --> Mud Pits to display the default Shaker Tanks screen.
24-6
www.nov.com
D811001248-MAN-0001
Revision 01
Page 24-7 of 8
24
S-DAQ
Alarm Displays
Depending on your rig configuration, you may be able to set up alarms for many gauges, graphs,
or readings displayed on the S-DAQ screens. See section titled "Mud Pump Displays and
Controls" on page 24-2.
Also see section titled "Alarm Setup" on page 3-6 for more
information.
Suction Tanks
At the Shaker Tanks screen, press Suction A - D to display the Mud Pit - Suction Tanks screen.
24-7
www.nov.com
24
S-DAQ
D811001248-MAN-0001
Revision 01
Page 24-8 of 8
Alarm Displays
Depending on your rig configuration, you may be able to set up alarms for many gauges, graphs,
or readings displayed on the S-DAQ screens. See section titled "Mud Pump Displays and
Controls" on page 24-2.
Also see section titled "Alarm Setup" on page 3-6 for more
information.
24-8
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.25
Top Drive System (TDS)
www.nov.com
D811001248-MAN-001
Revision 01
Page 25-1 of 20
Operator Screen
Press <Driller or AD> Tools --> Top Drive to display the Top Drive operator screen.
Tool Ownership
Assume ownership of the top drive to enable controls. See section titled "Tool Ownership" on page
2-34.
25-1
www.nov.com
25
D811001248-MAN-001
Revision 01
Page 25-2 of 20
Digital readings are represented by blue or green bars that rise and fall to indicate the current
values. Black markers indicate the current user-defined setpoint values.
Current throttle (speed), drill torque, makeup torque, spin speed, and spin torque values display
along the top of the screen.
25-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 25-3 of 20
25
Status Indicators
Current status indicators display along the right side of the Top Drive operator screen.
IBOP Closed: Yellow indicates that the internal blowout preventer (IBOP) is closed.
See section titled "Elevator, Torque Wrench, and IBOP Controls" on page 25-9.
BX Elev Closed: Green indicates that the BX elevator is closed. See section titled
"Elevator, Torque Wrench, and IBOP Controls" on page 25-9.
RLA Home: Green indicates that the rotating link adapter (RLA) is in the home
position. See section titled "CCW and CW Link Rotation" on page 25-13.
Slips (Open/Closed): Green Slips Open indicates that the power slips are open
and a green Slips Closed indicator means they are closed. See Chapter 18, titled
"Power Slips.
Brake On: Yellow indicates that the brake is engaged. See section titled "Brake
Controls" on page 25-11.
Ramp Failed: Red indicates that the motor ramp-up failed. See section titled
"Auxiliary Motors" on page 25-18.
Drive Fault: Red indicates a variable frequency drive (VFD) fault. See section titled
"Motor/VFD Status" on page 25-16.
25-3
www.nov.com
25
D811001248-MAN-001
Revision 01
Page 25-4 of 20
Hydraulic Alarm: Red indicates hydraulic pressure has fallen below acceptable
limits.
!
If the top drive continues rotating with low hydraulic
pressure, severe equipment damage may occur.
Lube Alarm: Red indicates that the gear box lubrication level has fallen below an
acceptable level (alarm state). See section titled "Auxiliary Motors" on page 25-18.
Blower Alarm: Red indicates a blower fault. See section titled "Auxiliary Motors" on
page 25-18.
Power Limit: Red indicates that the variable frequency drives (VFDs) and motors
have reached a predefined power limit value. See Chapter 19, titled "Power System.
Operator messages display along the bottom of the screen. Messages include operational status
information (such as brief descriptions of interlock conditions that are preventing certain
operations).
Define a maximum throttle value, then press Set to confirm close the keypad.
Press the blue arrow up or down buttons located at the bottom of the graph to incrementally
increase or decrease the Throttle setpoint value.
25-4
www.nov.com
D811001248-MAN-001
Revision 01
Page 25-5 of 20
25
Zero Throttle
Press Zero Throttle to remove throttle from the top drive and reduce its speed to zero.
Define a drill torque limit, then press Set to confirm the value and close the keypad.
Press the blue arrow up or down buttons located at the bottom of the drill torque graph to
incrementally increase or decrease the Drill Torque value.
Define a makeup torque limit, then press Set to confirm the value and close the keypad.
25-5
www.nov.com
25
D811001248-MAN-001
Revision 01
Page 25-6 of 20
Define a spin speed limit, then press Set to confirm the value and close the keypad.
25-6
www.nov.com
D811001248-MAN-001
Revision 01
Page 25-7 of 20
25
Define a spin torque limit, then press Set to confirm the value and close the keypad.
Press Reverse, Off (disable), or Forward to define the top drives spin direction. A green backlight
marks the current selection.
Press Drill, Spin, or Torque to select a top drive mode:
R
Select Drill mode to run the top drive at the speed and Drill Torque setpoints. See
section titled "Speed and Torque Controls" on page 25-4.
Select Spin mode to run the top drive at the user-defined spin speed and spin
torque. See section titled "Speed and Torque Controls" on page 25-4.
25-7
www.nov.com
25
D811001248-MAN-001
Revision 01
Page 25-8 of 20
Press and hold the Torque button to run the top drive using the user-defined Make
Up Torque setpoint. Release the button to return to Spin mode. See section titled
"Speed and Torque Controls" on page 25-4.
Press and hold the Torque button to execute a make up or break out sequence.
The selected direction determines if it is a make up or a break out sequence.
Make Up Sequence
R
With the Top Drive direction set to Forward - When the Torque button is pressed the
Top Drive will verify that the connection is shouldered by first executing a spin in
sequence. When the feedback torque is at or greater than the spin torque setting the
torque limit is then ramped up to the make up torque setting. Once the torque
feedback is equal to or greater than the make up torque setting the connection is
complete and the operator can release the Torque button. At this point the torque
limit will then be ramped down.
With the Top Drive direction set to Reverse - When the Torque button is pressed the
Top Drive will begin to ramp the torque limit to the maximum torque setting. When
the connection breaks and the torque feedback is less than the spin torque setting
the Top Drive will then go into the spin out phase and stay there until the operator
releases the Torque button.
25-8
www.nov.com
D811001248-MAN-001
Revision 01
Page 25-9 of 20
25
Press the Elevator Rotation - Down or Up button to define the elevator rotation.
Press the Elevator - Arm button to arm the pipe trigger, located at the back of the
elevator. The elevator closes when the pipe presses the trigger.
DRIL
L
TDS
LINK
OPE
TILT
FLO
AT
TDS
CLO
SE
LINK
OPE
N
CLO
SE
OPE
N
TDS
ELEV
ATO
R
RACK
CLO
SE
ER JA
W
OFF
/AUT
O
CLO
SE
DRAW
OVERWORKS
RIDE
PARK
IN
G BR
AKE
DOLL
Y EN
TDS
ELE
VAT
OR
ABLE
SLIP
S EN
OPE
N
ABLE
CLO
SE
IBOP
Torque Wrench
R
Press and hold the Torque Wrench - Clamp button to manually clamp the torque
wrench onto the drill pipe. A blue outline surrounds the button when active.
25-9
www.nov.com
25
D811001248-MAN-001
Revision 01
Page 25-10 of 20
Press the Torque Wrench - Auto toggle button to use automatic torque wrench
mode during makeup operations.
IBOP
Press the IBOP - Open or Close button to open or close the internal blowout preventer (IBOP). A
green backlight marks the current selection.
You can also control the IBOP using the IBOP - Open or Close discrete switch located on the
operator workstations left control panel.
DRIL
TDS
LINK
FLO
AT
OPE
TILT
TDS
CLO
SE
LINK
OPE
N
CLO
SE
TDS
ELE
VATO
R
RAC
KER
OFF
/AUTO
JAW
CLO
S
DRAW
OVE WORKS
RRID
E
PAR
KIN
G BR
AKE
DOLL
Y EN
OPE
N
ABLE
SLIP
OPE
N
S EN
ABLE
CLO
SE
CLO
SE
IBOP
IBOP
25-10
www.nov.com
D811001248-MAN-001
Revision 01
Page 25-11 of 20
25
Brake Controls
Press Brake to display the top drives brake controls.
Press the Brake - Off, Auto, or On buttons to set the top drive brake mode:
R
Select Brake - Auto to automatically disengage the brake when the operator
demands throttle, and automatically engage the brake when the operator returns the
speed to zero throttle position. The brake will not engage until the drive stops, and is
not holding torque.
25-11
www.nov.com
25
D811001248-MAN-001
Revision 01
Page 25-12 of 20
Dolly Controls
Press Dolly to display the dolly controls.
Select Dolly - Auto to allow the dolly to automatically extend and retract.
Press and hold the Dolly - Manual button to manually control the dolly. The dolly
will stop in mid tavel if button is released.
Press and hold the Dolly - Extend or Retract buttons as needed while in manual
mode.
25-12
www.nov.com
D811001248-MAN-001
Revision 01
Page 25-13 of 20
25
Link Controls
Press Links to display the top drives link controls.
Press the CCW or CW - Home button to move the rotating link adapter to the next
preset home position in the selected direction.
The RLA Home status indicator displays green when the rotating link adapter (RLA) is in the home
position. See section titled "Status Indicators" on page 25-3.
The Link Tilt must be in Float to enable RLA or Link Tilt rotation (see section titled "Link Tilt
below).
A green backlight marks the current selection.
Link Tilt
Press the Link Tilt - Drill, Float, or Tilt buttons to control the elevator links:
R
Select Drill to tilt the elevator links backward into a position that allows drilling
operations to proceed.
Select Float to allow the elevator links to float into a neutral position.
Select Tilt to tilt the elevator links forward to the preset derrickman and mousehole
positions. Press once to tilt forward to the preset derrickman position. After
unlocking the link tilt assembly mousehole position (see below), press this button
again to tilt forward to the mousehole.
Mousehole
Press the Mousehole - Unlock button to allow the links to tilt forward to the preset mousehole
position.
After unlocking, press the Link Tilt - Tilt button to tilt forward to the mousehole.
25-13
www.nov.com
25
D811001248-MAN-001
Revision 01
Page 25-14 of 20
25-14
www.nov.com
D811001248-MAN-001
Revision 01
Page 25-15 of 20
25
Assignments
Press Top Drive --> Assignments to display the Drawworks/Top Drive Assignments screen.
This screen provides a way for the operator to assign VFD motors to the drawworks and the top
drive. It also displays the current status of all VFDs.
See Chapter 4, titled "Assignments for more information.
25-15
www.nov.com
25
D811001248-MAN-001
Revision 01
Page 25-16 of 20
Motor/VFD Status
Press Top Drive --> Status to display the Motor/VFD Status screen.
This screen displays the chopper module drawworks brake resistor (DBR) status, as well as the
status of the top drive motor and assigned VFD.
On Line Capacity: Displays the kilowatt (kW) capacity (continuous current) for the
parallel chopper modules.
Health: Displays green to indicate that the chopper is online and operating normally;
red to indicate a fault or alarm state; black to indicate that the chopper is offline.
DBR Air Flow: Displays green to indicate that the drawworks brake resistor air flow
fan is on and operating normally; black to indicate it is off.
Speed Command: Displays the current speed command value received by the
motor.
Torque Limit: Displays the user-defined torque limit value. See section titled
"Speed and Torque Controls" on page 25-4.
Status: Displays the status of the assigned VFD motor; see section titled "Status
Displays" on page 25-18.
25-16
www.nov.com
D811001248-MAN-001
Revision 01
Page 25-17 of 20
25
Fault Reset
The Fault Reset button is located in the top right corner of the Motor/VFD Status screen.
Press the Fault Reset button to clear fault displays after the condition is corrected.
!
Resetting the faults does not clear active faults or alarms.
25-17
www.nov.com
25
D811001248-MAN-001
Revision 01
Page 25-18 of 20
Auxiliary Motors
Press Top Drive --> Auxiliary Motors to display the Auxiliary Motors screen.
This screen displays the status for the lube and blower motors. You can also assume manual
control of lube and blower motors using this screen.
Status Displays
R
Oil Temp: Red indicates that the motors oil temperature has exceeded acceptable
limits.
Oil Pressure: Red indicates that pressure has exceeded or fallen below acceptable
limits.
Motor Overtemp: Red indicates that the motor temperature has exceeded
acceptable limits.
Air Pressure: Red indicates that pressure has exceeded or fallen below acceptable
limits.
Manual Controls
Press the Manual Controls - Stop or Start button to manually control a lube or blower motor.
A green or red backlight indicates the current selection.
25-18
www.nov.com
D811001248-MAN-001
Revision 01
Page 25-19 of 20
25
Data Trends
Press Top Drive --> Data Trends to display the Top Drive Data Trends screen.
The Data Trends screen displays the top drives drilling speed and torque values graphically:
R
Press Speed (Day) to display drilling speed data for the past 24 hours.
Press Speed (Hour) to display drilling speed data for the past hour.
Press Torque (Day) to display torque speed data for the past 24 hours.
Torque (Hour) to display torque speed data for the past hour.
25-19
www.nov.com
25
D811001248-MAN-001
Revision 01
Page 25-20 of 20
25-20
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.26
V-DAQ
www.nov.com
D811001248-MAN-001
Revision 01
Page 26-1 of 2
V-DAQ
Operator Screen
Press <Driller or AD> Tools --> V-DAQ to display the V-DAQ operator screen.
26-1
www.nov.com
26
V-DAQ
D811001248-MAN-001
Revision 01
Page 26-2 of 2
Navigation
Press Screens located on the VDAQ operator screen to display the screen selection menu.
26-2
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.27
Zone Management System (ZMS)
www.nov.com
D811001248-MAN-001
Revision 01
Page 27-1 of 8
27-1
www.nov.com
27
D811001248-MAN-001
Revision 01
Page 27-2 of 8
Status Displays
R
A red Zone Management System Locked Out display (located in the top left
corner of the screen) indicates that ZMS is shut off.
A red Lock Out display indicates that the tool has been locked out of the ZMS
system. See section titled "Equipment Lockout" on page 27-6.
A red Override display indicates that the tool override is engaged. See section titled
"Equipment Override" on page 27-4.
A red Interlock display indicates that further tool movement is prevented by a ZMS
interlock.
27-2
www.nov.com
D811001248-MAN-001
Revision 01
Page 27-3 of 8
27
Release ownership of the tools from either the tool screen, or push the button normally located on
the operator workstations right control panel (see illustration below).
L
TOO IP
H
ERS LL
N
W
A
O
ASE
E
L
E
R
DEC
SE
INCR
EASE
L
TOO IP
H
ERS
OWN SE ALL
A
RELE
SE/
CLO K
LOC
N/
OPE
O
T
AU
REA
LOW
LIC F
RAU ALVE
HYD
V
CMC UT OFF
SH
AIR
KING E
WOR
R
CMC PRESSU
APV
SE
CLO
N
OPE
MAIN
CMC E
VALV
PULL
PAY
EAD
CATH
27-3
www.nov.com
27
D811001248-MAN-001
Revision 01
Page 27-4 of 8
Equipment Override
Press the Override button located at the top of the screen to display the ZMS Equipment
Override screen. Return to this screen at any time by pressing Override.
A red Zone Management System Locked Out display (located in the top left corner of the
screen) indicates that ZMS is shut off.
27-4
www.nov.com
D811001248-MAN-001
Revision 01
Page 27-5 of 8
27
Equipment overrides can be used to move equipment into zones where ZMS would normally
prevent movement.
Engage the override by releasing ownership of the tool, then pressing and holding its Override
button on the ZMS Equipment Override screen.
27-5
www.nov.com
27
D811001248-MAN-001
Revision 01
Page 27-6 of 8
Equipment Lockout
Press the Lock Out button located at the top of the screen to display the ZMS Equipment
Lockout screen.
A red Zone Management System Locked Out display (located in the top left corner of the
screen) indicates that ZMS is shut off.
27-6
www.nov.com
D811001248-MAN-001
Revision 01
Page 27-7 of 8
27
Use equipment lockouts (not ZMS lockout) to remove a tool from ZMS calculations (to perform
maintenance, for example). Tools locked out cannot receive enable signals from ZMS, and
therefore cannot be moved (except in maintenance mode). The tool becomes invisible to all other
ZMS participants; other tools can enter zones occupied by locked out equipment and collide with
them.
Press the appropriate tools Lock Out toggle button to engage equipment lockout. Press again to
disengage.
27-7
www.nov.com
27
D811001248-MAN-001
Revision 01
Page 27-8 of 8
ZMS Menu
Press the ZMS button located on the main menu bar to display its tool menu.
27-8
www.nov.com
FINAL DOCUMENTATION
Amphion Operators Guide
Section 1.28
Appendix
www.nov.com
D811001248-MAN-001
Revision 01
Page A-1 of 6
Appendix
Network Commands
Opening a Command Prompt
1. Press <Ctrl+Escape> to display the Windows Start menu.
2. Click Run, then type cmd into the field provided.
A-1
www.nov.com
Appendix
D811001248-MAN-001
Revision 01
Page A-2 of 6
A-2
www.nov.com
D811001248-MAN-001
Revision 01
Page A-3 of 6
Appendix
-t 123.45.67.8
IP Config
Use the ipconfig command to determine the domain name server (DNS), IP address, subnet
mask, and default gateway assigned to the current computer.
Use the ipconfig /all command to list the IP address, subnet mask address, and other information
for each network card to which the current computer is connected.
Tracert
Use the tracert command and either the url or IP address to display hop information (all network
devices between the your computer and the destination address).
Syntax example: tracert
A-3
www.nov.com
Appendix
D811001248-MAN-001
Revision 01
Page A-4 of 6
Nslookup
Use the nslookup command and a url address to troubleshoot name resolution issues. Displays
server name and IP address information.
Syntax example: nslookup
www.varco.com
A-4
www.nov.com
D811001248-MAN-001
Revision 01
Page A-5 of 6
Appendix
A-5
www.nov.com
Appendix
D811001248-MAN-001
Revision 01
Page A-6 of 6
A-6
www.nov.com