Professional Documents
Culture Documents
L17,1950S BN
L17,1950S BN
L17,1950S BN
1. Model Description
MODEL L1750S-BNN
L1950S-BNN
BRAND
SUFFIX
FLATRON L1750S
Product Name FLATRON L1950S
2.
ANUKEP
LG
LEE H.J
05.12.30
KIM J.O
05.12.30
Part No.
3828TSL093V
Printing Specification
1. Trim Size (Format) : 215mm x 280 mm
2. Printing Colors
Cover : 2 COLORS (M100%, BLACK)
Inside : 1 COLORS (Black)
3. Stock (Paper)
Cover : 100 g/
Inside : 100 g/
4. Printing Method :
5. Bindery : Saddle stitch
6. Language : English
7. Number of pages : 28 (Including blank 1page)
3.
Special Instructions
(1) Origin Notification
* LGEDI : Printed in Indonesia
* LGESP : Printed in Brazil
* LGENT : Printed in China
4.
Changes
8
7
6
5
4
3
2
1
REV.
NO.
MM/DD/YY
SIGNATURE
CHANGE NO.
CHANGE
CONTENTS
P/NO. 3828TSL093V
Total pages :28pages
Pagination sheet
Cover
Front cover
Inside
English
English
English
English
English
blank
..
English
English
English
English
English
Rear cover
Inside
22
23
24
25
26
Rear
Cover
Website:http://biz.LGservice.com
E-mail:http://www.LGEservice.com/techsup.html
COLOR MONITOR
SERVICE MANUAL
CHASSIS NO. : CL-82
MODEL:
(
L1750S (L1750S-BNN.AN**EP)
L1950S (L1950S-BNN.AN**EP)
) **Same model for Service
CAUTION
BEFORE SERVICING THE UNIT,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
Blank Page1
CONTENTS
SPECIFICATIONS ................................................... 2
PRECAUTIONS ....................................................... 3
TIMING CHART ....................................................... 7
DISASSEMBLY ....................................................... 8
BLOCK DIAGRAM ................................................... 9
DESCRIPTION OF BLOCK DIAGRAM....................10
ADJUSTMENT ...................................................... 12
SPECIFICATIONS
1. LCD CHARACTERISTICS
Type
: TFT Color LCD Module
Active Display Area : 17 inch-L1750S
: 19 inch-L1950S
Size
: 358.5(W) x 296.5(H) x 17.0(D)-L1750S
: 404.2(W) x 330(H) x 22.0(D)-L1950S
Pixel Pitch
: 0.264 (H) x 0.264 (V)-L1750S
: 0.294 (H) x 0.294 (V)-L1950S
Color Depth
: 16.2M colors
Electrical Interface
: LVDS
Surface Treatment
: Hard-coating(3H), Anti-Glare
Operating Mode
: Normally White, Transmissive mode
Backlight Unit
: 4-CCFL
2. OPTICAL CHARACTERISTICS
2-1. Viewing Angle by Contrast Ratio 10
L1750S
Left : -60min., -70(Typ) Right : +60min., +70(Typ)
Top :+45min., +60(Typ) Bottom : -50min., -60(Typ)
L1950S
Left : -70min., -80(Typ) Right : +70min., +80(Typ)
Top :+75min., +85(Typ) Bottom : -75min., -85(Typ)
2-2. Luminance
: 185(min), 250(Typ)
: 300(min), 450(Typ)-L1750S
: 300(min), 500(Typ)-L1950S
4. Max. Resolution
D-sub Analog
5. POWER SUPPLY
5-1. Power : AC 100~240V, 50/60Hz , 1.0A
5-2. Power Consumption
MODE
: R, G, B Analog
: 0~0.71 V
: 0 Vp-p
: 0.467 Vp-p
: 0.714 Vp-p
: 75
POWER ON (NORMAL)
ON/ON
ACTIVE
GREEN
less than 39 W-L1950S
STAND-BY
OFF/ON
OFF
less than 1 W
AMBER
SUSPEND
ON/OFF
OFF
less than 1 W
AMBER
DPMS OFF
OFF/OFF
OFF
less than 1 W
AMBER
6. ENVIRONMENT
6-1. Operating Temperature : 10C~35C
6-2. Relative Humidity
: 10%~80%
6-3. MTBF
: 50,000 HRS with 90%
Confidence level
Lamp Life
: 50,000 Hours(Min)
7. DIMENSIONS (with TILT/SWIVEL)
L1750S
Width
: 368 mm (14.49'')
Depth
: 230.5 mm (9.07'')
Height
: 389.2 mm (15.32'')
: 1280 x 1024@75Hz
L1950S
Width
Depth
Height
: 413 mm (16.26'')
: 230.5 mm (9.07'')
: 421.4 mm (16.59'')
-2-
PRECAUTION
WARNING FOR THE SAFETY-RELATED COMPONENT.
WARNING
CAUTION
Please use only a plastic screwdriver to protect yourself
from shock hazard during service operation.
-3-
To Instrument's
exposed
METALLIC PARTS
1.5 Kohm/10W
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this
service manual and its supplements and addenda, read
and follow the SAFETY PRECAUTIONS on page 3 of this
publication.
NOTE: If unforeseen circumstances create conflict
between the following servicing precautions and any of the
safety precautions on page 3 of this publication, always
follow the safety precautions. Remember: Safety First.
General Servicing Precautions
1. Always unplug the receiver AC power cord from the AC
power source before;
a. Removing or reinstalling any component, circuit
board module or any other receiver assembly.
b. Disconnecting or reconnecting any receiver electrical
plug or other electrical connection.
c. Connecting a test substitute in parallel with an
electrolytic capacitor in the receiver.
CAUTION: A wrong part substitution or incorrect
polarity installation of electrolytic capacitors may
result in an explosion hazard.
d. Discharging the picture tube anode.
2. Test high voltage only by measuring it with an
appropriate high voltage meter or other voltage
measuring device (DVM, FETVOM, etc) equipped with
a suitable high voltage probe.
Do not test high voltage by "drawing an arc".
3. Discharge the picture tube anode only by (a) first
connecting one end of an insulated clip lead to the
degaussing or kine aquadag grounding system shield
at the point where the picture tube socket ground lead
is connected, and then (b) touch the other end of the
insulated clip lead to the picture tube anode button,
using an insulating handle to avoid personal contact
with high voltage.
4. Do not spray chemicals on or near this receiver or any
of its assemblies.
5. Unless specified otherwise in this service manual,
clean electrical contacts only by applying the following
mixture to the contacts with a pipe cleaner, cottontipped stick or comparable non-abrasive applicator;
10% (by volume) Acetone and 90% (by volume)
isopropyl alcohol (90%-99% strength)
CAUTION: This is a flammable mixture.
Unless specified otherwise in this service manual,
lubrication of contacts in not required.
6. Do not defeat any plug/socket B+ voltage interlocks
with which receivers covered by this service manual
might be equipped.
7. Do not apply AC power to this instrument and/or any of
its electrical assemblies unless all solid-state device
heat sinks are correctly installed.
8. Always connect the test receiver ground lead to the
receiver chassis ground before connecting the test
receiver positive lead.
Always remove the test receiver ground lead last.
-4-
Replacement
1. Carefully insert the replacement IC in the circuit board.
2. Carefully bend each IC lead against the circuit foil pad
and solder it.
3. Clean the soldered areas with a small wire-bristle
brush. (It is not necessary to reapply acrylic coating to
the areas).
"Small-Signal" Discrete Transistor
Removal/Replacement
1. Remove the defective transistor by clipping its leads as
close as possible to the component body.
2. Bend into a "U" shape the end of each of three leads
remaining on the circuit board.
3. Bend into a "U" shape the replacement transistor leads.
4. Connect the replacement transistor leads to the
corresponding leads extending from the circuit board
and crimp the "U" with long nose pliers to insure metal
to metal contact then solder each connection.
Power Output, Transistor Device
Removal/Replacement
1. Heat and remove all solder from around the transistor
leads.
2. Remove the heat sink mounting screw (if so equipped).
3. Carefully remove the transistor from the heat sink of the
circuit board.
4. Insert new transistor in the circuit board.
5. Solder each transistor lead, and clip off excess lead.
6. Replace heat sink.
Diode Removal/Replacement
1. Remove defective diode by clipping its leads as close
as possible to diode body.
2. Bend the two remaining leads perpendicular y to the
circuit board.
3. Observing diode polarity, wrap each lead of the new
diode around the corresponding lead on the circuit
board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder
joints of the two "original" leads. If they are not shiny,
reheat them and if necessary, apply additional solder.
Fuse and Conventional Resistor
Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board
hollow stake.
2. Securely crimp the leads of replacement component
around notch at stake top.
3. Solder the connections.
CAUTION: Maintain original spacing between the
replaced component and adjacent components and the
circuit board to prevent excessive component
temperatures.
-5-
At Other Connections
Use the following technique to repair the defective copper
pattern at connections other than IC Pins. This technique
involves the installation of a jumper wire on the
component side of the circuit board.
1. Remove the defective copper pattern with a sharp
knife.
Remove at least 1/4 inch of copper, to ensure that a
hazardous condition will not exist if the jumper wire
opens.
2. Trace along the copper pattern from both sides of the
pattern break and locate the nearest component that is
directly connected to the affected copper pattern.
3. Connect insulated 20-gauge jumper wire from the lead
of the nearest component on one side of the pattern
break to the lead of the nearest component on the
other side.
Carefully crimp and solder the connections.
CAUTION: Be sure the insulated jumper wire is
dressed so the it does not touch components or sharp
edges.
-6-
TIMING CHART
VIDEO
A
E
D
SYNC
C
<< Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (s), Vertical etc... (ms) >>
Mode
1
Sync
H/V
Sort Polarity
H
+/-
+/-
+/-
+/-
+/-
+/-
10
11
12
13
Back Porch
(B)
Resolution
96
48
640 x 350
37
60
720
18
108
54
449
400
12
35
31.469
800
640
16
96
48
59.94
525
480
10
33
37.5
840
640
16
64
120
75
500
480
16
37.879
1056
800
40
128
88
60.317
628
600
23
46.875
1056
800
16
80
160
75.0
625
600
21
49.725
1152
832
32
64
224
74.55
667
624
39
65.0
48.363
1344
1024
24
136
160
60.0
806
768
29
78.75
60.123
1312
1024
16
96
176
75.029
800
768
28
68.681
1456
1152
32
128
144
75.062
915
870
39
61.805
1504
1152
18
134
200
65.96
937
900
31
63.981
1688
1280
48
112
248
60.02
1066
1024
38
Dot
Clock
Frequency
25.175
31.469
800
640
16
70.09
449
350
31.468
900
70.08
28.321
25.175
31.5
40.0
49.5
57.283
100.0
92.978
108.0
135.0
79.976
1688
1280
16
144
248
75.035
1066
1024
38
-7-
720 X 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1152 x 870
1152 x 900
1280 x 1024
1280 x 1024
DISASSEMBLY
#1
#2
#4
#3
#6
#5
#8
#7
-8-
AC Input
-9-
LIPS
D-SUB
1.8V
3.3V
5V
TSU16AL &
TR(KTA1273)
3.3V Reg.
78D33
12V
3.3V
5V
3.3V
1.8V
5V
LVDS
(Low Voltage
Differential
Signaling)
(ADC/LVDS/SCALER
/INPUT SWITCHING
/TMDS)
TSU16AL
including
R,G,B
differential
LCD Module
MTV312
MICOM
BLOCK DIAGRAM
- 10 -
12V
50 ~ 60Hz
EMI
COMPONENTS
INPUT RECTIFIER
AND FILTER
HVDC
ENERGY
TRANSFER
100KHz
OUTPUT RECTIFIER
AND FILTER
LINE
100 ~ 240V
5V
GND
PWM
COMTROL
CIRCUIT
SIGNAL
COLLENTION
PHOTOCOUPLER
ISOLATI ON
PRIMARY
SECONDARY
Operation description_LIPS
1. EMI components.
This part contains of EMI components to comply with global marketing EMI standards like FCC, VCCI CISPR, the
circuit included a line-filter, across line capacitor and of course the primary protection fuse.
2. Input rectifier and filter.
This part function is for transfer the input AC voltage to a DC voltage through a bridge rectifier and a bulk capacitor.
3. Energy Transfer.
This part function is transfer the primary energy to secondary through a power transformer.
4. Output rectifier and filter.
This part function is to make a pulse width modulation control and to provide the driver signal to power switch, to
adjust the duty cycle during different AC input and output loading condition to achive the dc output stablize, and also
the over power protection is also monitor by this part.
5. Photo-Coupler isolation.
This part function is to feed back the DC output changing status through a photo transistor to primary controller to
achieve the stabilized DC output voltage.
6. Signal collection.
This part function is to collect the any change from the DC output and feed back to the primary through photo
transistor.
- 11 -
ADJUSTMENT
Windows EDID V1.0 User Manual
- 12 -
SERVICE OSD
1) Turn off the power switch at the front side of the display.
2) Wait for about 5 seconds and press MENU, POWER switch with 1 second interval.
3) The SVC OSD menu contains additional menus that the User OSD menu as described below.
a) Auto Color : W/B balance and Automatically sets the gain and offset value.
b) NVRAM INIT : EEPROM initialize.(24C08)
c) CLEAR ETI : To initialize using time.
d) AGING : Select Aging mode(on/off).
e) R/G/B-9300K : Allows you to set the R/G/B-9300K value manually.
f) R/G/B-6500K : Allows you to set the R/G/B-6500K value manually.
g) R/G/B-Offset : Allows you to set the R/G/B-Offset value manually.(Analog Only)
h) R/G/B-Gain : Allows you to set the R/G/B-Gain value manually.(Analog Only)
i) MODULE : To select applied module.
A
9
IBM
Compatible PC
Video Signal
Generator
15
10
5
11
6
1
6
1
C
13
se
PARALLEL PORT
2C
tu
23
No
RS
5V
OFF
14
ON
LL
EL
RA
PA
5V
220
WE
VG
CS
T
PO
S
MO
NI
TO
E
4.7K
74LS06
E ST Switch
- 13 -
4.7K
4.7K
5V
OFF
YN
V-S
Control Line
25
74LS06
TROUBLESHOOTING GUIDE
1. NO POWER
NO POWER
(POWER INDICATOR OFF)
CHECK J705
VOLTAGE
PIN5, PIN6 (5V)?
NO
YES
CHECK
U501 PIN 8 VOLTAGE
(5V) ?
NO
YES
NO PROBLEM
IS U201
PIN90 (3.3V)
VOLTAGE ?
NO
YES
NO
YES
CHECK U201
Waveforms
1
U201-#96
- 14 -
CHECK X-TAL
NO RASTER
(OSD IS NOT DISPLAYED)
J705
PIN5, PIN6
5V?
NO
YES
J705 PIN9
2.5V?
NO
YES
J705 PIN10
5V?
NO
1. CONFIRM BRIGHTNESS
OSD CONTRL STATE.
2. CHECK MICOM DIM-ADJ
PORT
YES
CHECK
PULSE AS
CONTACTING SCOPE
PROBE TO CAUTION LABEL.
(CONTACT PROBE TO
CAUTION LABEL.
CAN YOU SEE PULSE
AT YOUR
SCOPE?
NO
YES
REPLACE CCFL LAMP
IN THE LCD MODULE
- 15 -
LIPS
NO RASTER
(OSD IS NOT DISPLAYED)
U201
PIN 18, 90
3.3V?
NO
YES
U201
PIN96, 97
OSCILLATE AS
12MHZ?
NO
YES
U501
PIN43 IS 48KHz H-SYNC?
PIN44 IS 60Hz V-SYNC?
IS PULSE APPEARED
AT SIGNAL PINS?
AT MODE 12?
NO
YES
TROUBLE IN CABLE
OR LCD MODULE
Waveforms
1
U201-#96, 97
U501-#43 H-SYNC
- 16 -
U501-#44 V-SYNC
4. TROUBLE IN DPM
TROUBLE IN DPM
CHECK
R216, R217
R778, R781
NO
CHECK PC
PC IS NOT GOING
INTO DPM OFF MODE
YES
CHECK
U501 PIN 43.44
SYNC PULSE ?
NO
YES
TROUBLE IN U501
Waveforms
3
- 17 -
WIRING DIAGRAM
6631T11012W
or 6631T11020W
6631T20034M
or 6631T20023A
6631T11017X-L1750S
6631T11017Y-L1950S
- 18 -
060
010
020
080
040
070
050
090
120
100
030
110
EXPLODED VIEW
- 19 -
Part No.
Description
010
3091TKL143E
3091TKL176R
3091TKL144E
3091TKL144L
6304FLP274A
or 6304FLP330A
or 6304FLP331A
or 6304FLP248A
or 6304FLP256A
or 6304FLP257A
or 6304FLP258A
or 6304FLP298A
or 6304FLP299A
or 6304FLP300A
or 6304FLP301A
or 6304FLP275A
or 6304FLP279A
or 6304FLP280A
or 6304FLP317A
6304FLP210A
or 6304FLP264A
or 6304FLP142A
or 6304FLP184A
3809TKL100A
3809TKL101A
3809TKL101C
3043TKK227A
3043TKK227M
3043TKK227B
3043TKK227F
3043TKK228A
3043TKK228G
6871TST798A
6871TST798D
6871TST911A
6871TST911B
4951TKS199A
4951TKS199B
4951TKS200A
4951TKS200C
6871TPT282C
or 6871TPT312A
3313TL7100A
3313TL7100F
3313TL9079A
3313TL9079C
4951TKS203A
4951TKS203B
3550TKK740A
3550TKK741A
3550TKK741B
6410TBW004A
6410TEW010A
6410TPW003A
020
030
040
050
060
070
080
090
100
110
120
- 20 -
PART NO.
0CK104CK56A
0CK104CK56A
0CK104CK56A
0CK104CK56A
0CK103CK51A
0CK103CK51A
0CK103CK51A
0CK103CK51A
0CK103CK51A
0CK103CK51A
0CK103CK51A
0CK103CK51A
0CK103CK51A
0CK103CK51A
0CK103CK51A
0CK103CK51A
0CK103CK51A
0CK103CK51A
0CK103CK51A
0CK104CK56A
0CK104CK56A
0CK104CK56A
0CK104CK56A
0CK104CK56A
0CK103CK51A
0CK103CK51A
0CH8106F611
0CC030CK01A
0CC180CK41A
0CK103CK51A
0CK105CD56A
0CC680CK41A
0CK103CK51A
0CK103CK51A
0CC101CK41A
0CC101CK41A
0CK105CD56A
0CK103CK51A
0CK104CK56A
0CK104CK56A
0CK104CK56A
0CC680CK41A
0CE107EF610
0CK104CK56A
0CK103CK51A
0CE107EF610
0CE107EF610
0CK105CD56A
0CC102CK41A
0CK105CD56A
DIODEs
MAIN BOARD
CAPACITORS
C204
C205
C206
C207
C211
C213
C214
C215
C216
C217
C218
C219
C220
C221
C222
C223
C224
C225
C226
C230
C231
C232
C233
C240
C251
C503
C504
C506
C507
C508
C701
C707
C708
C709
C717
C718
C727
C732
C733
C734
C735
C744
C803
C805
C809
C812
C814
C817
C818
C819
PART NO.
D701
D702
D706
ZD701
ZD702
ZD703
ZD704
ZD711
ZD712
0DSIH00018A
0DSIH00018A
0DSIH00018A
0DZ560009GB
0DZ560009GB
0DZ560009GB
0DZ560009GB
0DZ560009GB
0DZ560009GB
0IKE704200H
0IPRPM3017A
0IZZTSZ595A
0IZZTSZ597A
0ICS240813B
0IPMGKE011A
ICs
Q502
U201
U501
U501
U502
U801
TRANSISTOR
U802
Q503
Q504
Q505
Q703
Q704
Q801
Q802
Q803
0TFVI80067A
0TRIH80001A
0TRIH80001A
0TRIH80001A
0TR390609FA
0TR390609FA
0TR127309AA
0TRIH80001A
0TR127309AA
RESISTORs
R201
R202
R203
R207
R208
R209
R210
R216
R217
R220
R240
R501
R503
R506
R508
R520
R521
R522
R523
R530
- 21 -
0RJ0682D677
0RJ0682D677
0RJ0682D677
0RJ3900D677
0RJ0682D677
0RJ0682D677
0RJ0682D677
0RJ0000D677
0RJ0000D677
0RJ4701D677
0RJ1001D677
0RJ4701D677
0RJ4701D677
0RJ4701D677
0RJ4701D677
0RJ4701D677
0RJ4701D677
0RJ4701D677
0RJ4701D677
0RJ1002D677
PART NO.
0RJ0000D677
0RJ3301D677
0RJ3301D677
0RJ4701D677
0RJ4701D677
0RJ4700D677
0RJ4700D677
0RJ0332D677
0RJ0332D677
0RJ1000D677
0RJ1000D677
0RJ1501D677
0RJ4702D677
0RJ0752D677
0RJ2001D677
0RJ0752D677
0RJ2001D677
0RJ0752D677
0RJ4700D677
0RJ4700D677
0RJ0102D677
0RJ4701D677
0RJ4701D677
0RJ0000D677
0RJ1000D677
0RJ0332D677
0RJ0332D677
0RJ1002D677
0RJ1002D677
0RJ0000D677
0RJ4701D677
0RJ4701D677
0RJ4700D677
0RJ1000D677
0RJ1000D677
0RJ1000D677
0RJ1000D677
0RJ0000D677
0RJ0682D677
0RJ0682D677
0RH0000D622
0RJ1002D677
0RH2000D622
0RH2000D622
0RJ0000D677
0RJ2202D677
0RJ5600D677
0RJ1002D677
0RJ0000D677
0RH0000D622
0RJ0272D677
0RJ2000D677
6212AA2004A
OTHERs
X501
CONTROL BOARD
C1
C2
LED1
0CK104CK56A
0CK104CK56A
0DLLT0208AA
- 22 -
PART NO.
0RJ4701D677
0RJ4701D677
0RJ2001D677
0RJ2001D677
0RJ4701D677
6600TR1002A
6600TR1002A
6600TR1002A
6600TR1002A
6600TR1002A
0DZ560009GB
0DZ560009GB
SCHEMATIC DIAGRAM
1. TSU56AL / TSU16AL
#1
Waveforms
U201-#96, 97
L1750S / L1950S
TSU56AL / TSU16AL
- 23 -
2. MICOM
2
#2
U501-#44 V-SYNC
L1750S / L1950S
MICOM
Waveforms
U501-#43 H-SYNC
- 24 -
3.POWER
#3
L1750S / L1950S
POWER
- 25 -
#4
Waveforms
R216, R778 H-Sync
L1750S / L1950S
CONNECTOR & JACKS
- 26 -
P/NO : 3828TSL093V
Nov. 2005
Printed in Korea