Professional Documents
Culture Documents
6 - Linetrap - 400kv - 10mH - 3150 - A - R - 0
6 - Linetrap - 400kv - 10mH - 3150 - A - R - 0
2012
TECHNICAL SPECIFICATIONS
FOR
Page 1 of 17
1.
All the drawings, i.e. elevation, side view, plan, cross sectional view etc.,
in AutoCAD format and manuals in PDF format, for offered item shall be
submitted. Also the hard copies as per specification shall be submitted.
2.
The bidder shall submit Quality Assurance Plan for manufacturing process
and Field Quality Plan with the technical bid.
3.
The bidder shall have to submit all the required type test reports for the
offered item. In case of non-submission of the type test reports with the
offer, the bid shall be liable to be rejected.
4.
The bidder must fill up all the point of GTP for offered item/s. Instead of
indicating refer drawing, or as per IS/IEC, the exact value/s must be
filled in.
5.
All the points other than GTP, which are asked to confirm in technical
specifications must be submitted separately with the bid.
6.
7.
Please note that the evaluation will be carried out on the strength of
content of bid only. No further correspondence will be made.
8.
The bidder shall bring out all the technical deviation/s only at the
specified annexure.
9.
Page 2 of 17
Sr.
No
1)
2)
3)
4)
The bidder should clearly indicate the quantity and Single Value
Contract executed during last FIVE (5) years, for the offered
equipment. Bidder should have executed one single contract during
last five years for the quantity equivalent to tender / bid.
The details are to be submitted in following format,
ITEMS
SUPPLIED
TO
5)
ORDER
REFERENCE No.
& DATE
ITEMS
QUANTITY
ORDER
FULLY
EXECUTED
YES/NO
STATUS, IF
ORDER
UNDER
EXECUTION
REMARK
Page 3 of 17
SCOPE:
This specification provides for design, engineering, manufacture, stage
testing, inspection and testing before dispatch, packing and delivery at
destination of Line Trap along with all accessories specified herein. The
line trap to be inserted into high voltage A.C transmission lines to prevent
undue loss of carrier signal power, typical in the range 30KHz to 500KHz,
under all power system conditions and to minimize interference from
carrier signaling systems on adjacent transmission lines.
1.2
It is not the intent to specify completely herein all details of the design
and construction of equipments. However, the equipment shall conform in
all respects to high standards of engineering, design and workmanship and
shall be capable of performing in continuous commercial operation up to
the Bidders guarantee acceptable to the Purchased, who will interpret in a
manner the meanings of drawings and specification and shall have the
power to reject any work or material which in his judgment is not in
accordance therewith. The equipment offered shall be complete with all
components necessary for it effective and trouble free operation. Such
components shall be deemed to be within the scope of Bidders supply,
irrespective of whether these are specifically brought out in this
specification and/or the commercial order or not.
2.0
2.1
STANDARDS:
Unless otherwise specified elsewhere in this specification, the rating as
well as performance and testing of the line trap shall conform but not
limited to the latest revisions and amendments available at the time of
placement of order of all the relevant standards as listed hereunder.
2.1.1: LINE TRAP
Sr.No.
Standard No.
Title
1.
IEC 60353 Second Line Trap for A.C Power System
edition, 1989-10
LINE TRAPS FOR AC POWER SPECIFICATION.
2.
IS: 8792-1978
3.
IS: 8793-1978
4.
5.
6.
IEC 99
IEC 99 1(1970)
7.
10.
Lightning Arresters
Part-1, Non-linear resistor type arresters
for a.c system.
IEC 60099-4/2006 Metal-oxide surge arresters without
gaps for a.c. systems
IS: 5561- 1970
Terminal Clamp/Connector
Page 4 of 17
3.0
3.1
PRINCIPAL PARAMETERS:
4.1
The Line Trap covered in this specification shall meet the technical
requirements listed hereunder.
4.1.1 PRINCIPAL TECHNICAL PARAMETERS OF LINE TRAP
Sr.
No.
1.
2.
3.
ITEM
Type of Line Trap Installation
Type of mounting
Suitable for system Frequency
SPECIFICATION
To be inserted into high
voltage A.C transmission
line phase in series
Pedestal
50 Hz
Page 5 of 17
9.
10.
11.
12.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21
ITEM
SPECIFICATION
Page 6 of 17
Page 7 of 17
6.0
Accessories :
Page 8 of 17
Page 9 of 17
Page 10 of 17
9. G E N E R A L R EQUIREMENTS F O R B I D D E R S :
1. The bidder shall furnish the full technical details, O&M manual, QAP &
drawings for the Line Trap offered.
2. The bidder shall have the experience of at least 10 years of manufacture
& supply of similar type of Line Trap.
3. The bidder shall furnish the full details of the orders executed.
4. Any deviation shall be clearly indicated separately.
5. The GETCO reserves right to increase or decrease the quantity at the
time of placing the order.
6. The GETCO reserve right either to accept or reject any of the offers
Without assigning the reason.
10. DRAWINGS:
The following drawings indicating all the dimensions and weight etc.
with complete technical details shall be enclosed together with technical bid:
(i)
General arrangement for Line Trap indicating dimensions,
technical parameters, weight etc.
(ii) Mounting pedestal for 1.0 mH/3150A Line trap
(iii) Name plate for line trap
(iv) Name plate for tuning pot
(v) Name plate for protective device
(vi) Special Name plate
(vii) Tuning pot ckt arrangement
(viii) Details of terminal clamp/connectors suitable for quad ACSR
Moose conductor.
(ix) Corona ring fixing arrangement for 1.0 mH/3150A Line trap
(x) Mounting alignment of line trap pedestal & post insulator
(xi) Steel structure for 1.0mH/3150A Line Trap
(xii) Mounting arrangement for 1.0mH/3150A Line trap
(xiii) Drawing for rigid/sliding clamp on bus support to suit 4 IPS AL.Tube
(xiv) Drawing for T-connector suitable for 4 IPS AL. Tube and Quad ACSR
Moose conductor.
(xv) 400KV Solid core post insulator
(xvi) Lightning Arrestor as protective device for Tuning Pot.
(xvii) Bird barriers
Page 11 of 17
Page 12 of 17
Page 13 of 17
The bidder shall have to supply the wave trap offered with
Tuning pot
Lightning arrestors
Mounting pedestal, Steel Structure and Solid core post insulator
Clamps & Connectors suitable for 4 IPS AL. Tube and Quad ACSR
Moose conductor
Bird barriers
Hardware & accessories
O&M manual
Any other accessories necessary for installation of wave trap.
Page 14 of 17
To be furnished by bidder
a) Centre Frequency
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Page 15 of 17
To be furnished by bidder
Sr.No. Particulars
Annexure A2 : Technical data for Tuning device
1
Power frequency withstand voltage for 5 sec
2
Tuning band arrangement
a) Band I
b) Band II
To be furnished by bidder
Sr.No. Particulars
Annexure A3 : Line trap construction data
1
Material of main coil
2
Material of terminal connector
3
Material of Pedestal
4
Material of mounting hard wares
5
Net weight
6
Whether corona rings are provided?
7
Whether Bird barriers are provided?
8
Overall diameter
9
Total height
10
No. of turns in Line trap main coil
11
Type of conductor whether solid or stranded
12
Cross sectional area of conductor
13
Overall conductor size
Type of construction i.e. No. of coils and
14
whether open type or covered with insulating
material
Type and material of spacers between turn to
15
turn
16
No. of tie rods in tie rod Assembly
17
No. of insulator column required
To be furnished by bidder
Page 16 of 17
Sr.No.
Particulars
Annexure A4 : Deviation if any from technical requirement
SCHEDULE OF REQUIREMENTS
Sr.No.
Description
400KV,
1.0
mH,
3150
Amp
Wave Trap with pedestal mounting
1.
Quantity
Page 17 of 17