Professional Documents
Culture Documents
WinCC S71200 S71500 Channel en
WinCC S71200 S71500 Channel en
WinCC S71200 S71500 Channel en
WinCC Connection to
S7-1200 and S7-1500
WinCC V7.3
http://support.automation.siemens.com/WW/view/en/101908495
The Application Examples are not binding and do not claim to be complete
regarding the circuits shown, equipping and any eventuality. The Application
Examples do not represent customer-specific solutions. They are only intended
to provide support for typical applications. You are responsible for ensuring that
the described products are used correctly. These Application Examples do not
relieve you of the responsibility to use sound practices in application, installation,
operation and maintenance. When using these Application Examples, you
recognize that we cannot be made liable for any damage/claims beyond the
liability clause described. We reserve the right to make changes to these
Application Examples at any time and without prior notice. If there are any
deviations between the recommendations provided in these Application
Examples and other Siemens publications e.g. Catalogs the contents of the
other documents have priority.
We do not accept any liability for the information contained in this document.
Any claims against us based on whatever legal reason resulting from the use of
the examples, information, programs, engineering and performance data etc.,
described in this Application Example shall be excluded. Such an exclusion shall
not apply in the case of mandatory liability, e.g. under the German Product Liability
Act (Produkthaftungsgesetz), in case of intent, gross negligence, or injury of life,
body or health, guarantee for the quality of a product, fraudulent concealment of a
deficiency or breach of a condition which goes to the root of the contract
(wesentliche Vertragspflichten). The damages for a breach of a substantial
contractual obligation are, however, limited to the foreseeable damage, typical for
the type of contract, except in the event of intent or gross negligence or injury to
life, body or health. The above provisions do not imply a change of the burden of
proof to your detriment.
Any form of duplication or distribution of these Application Examples or excerpts
hereof is prohibited without the expressed consent of Siemens Industry Sector.
Security
information
Siemens provides products and solutions with industrial security functions that
support the secure operation of plants, solutions, machines, equipment and/or
networks. They are important components in a holistic industrial security
concept. With this in mind, Siemens products and solutions undergo continuous
development. Siemens recommends strongly that you regularly check for
product updates.
For the secure operation of Siemens products and solutions, it is necessary to
take suitable preventive action (e.g., cell protection concept) and integrate each
component into a holistic, state-of-the-art industrial security concept. Third-party
products that may be in use should also be considered. For more information
about industrial security, visit http://www.siemens.com/industrialsecurity.
To stay informed about product updates as they occur, sign up for a productspecific newsletter. For more information, visit
http://support.automation.siemens.com.
10/2014
Table of Contents
Table of Contents
Warranty and Liability .............................................................................................. 2
1
Task................................................................................................................. 4
Solution........................................................................................................... 5
2.1
2.2
2.2.1
2.2.2
Overview ........................................................................................... 5
Hardware and software components .................................................. 7
Validity .............................................................................................. 7
Components used ............................................................................. 7
References .................................................................................................... 18
History .......................................................................................................... 18
10/2014
1 Task
Task
Figure 1-1
S7-1500
WinCC V7.3
Encrypted
process connection
S7-1200
Process connection
Introduction
The task is to provide process tags and AS messages of S7-1200 and S7-1500 in
WinCC V7.3.
It is to be possible to establish a protected HMI connection to S7-1500.
10/2014
2 Solution
2.1 Overview
Solution
2.1
Overview
Setup
The following scheme shows the most important components of the solution:
Figure 2-1
WinCC V7.3
S7-1500
S7-1200
PROFINET IE
Description
WinCC V7.3 provides the communication channel "SIMATIC S7-1200, S7-1500
Channel" for communication with S7-1200 and S7-1500 CPUs.
Communication to S7-1200 and S7-1500 can be realized with absolute addressing
and since WinCC V7.3 also with symbolic addressing.
Between WinCC V7.3 and S7-1500, a protected communication connection can be
established.
Characteristic features
Note
Access to the symbolic addresses and CPU alarming is effected via the online
connection to the CPU only.
10/2014
2 Solution
2.1 Overview
Features of the communication to S7-1200 and S7-1500
Password protection
Time synchronization
Export/Import function
1) Export of the tags from TIA Portal (only absolute addressing)
2) Import to WinCC via the WinCC Configuration Studio
Loading of AS symbols
Delimitation
Assumed knowledge
Basic knowledge of WinCC V7.3 and SIMATIC TIA Portal is assumed.
10/2014
2 Solution
2.2 Hardware and software components
2.2
2.2.1
Validity
This application is valid for
2.2.2
WinCC V7.3
S7-1500
Components used
The application was created with the following components:
Hardware components
Table 2-1
Siemens AG Copyright- 2014 All rights reserved
Component
No.
S7-1516-3 PN/DP
Development
system
Article number
6AG1516-3AN00-7AB0
Note
Alternatively, any other S71500 or S7-1200 can be used.
PC for configuration of
controller and WinCC.
The hardware requirements
for STEP 7 and WinCC apply.
Software components
Table 2-2
Component
NOTE
No.
Article number
WinCC V7.3
6AV63.1-....7-3...
TIA Portal
STEP 7 V13
Professional
6ES7822-1..03-..
Note
Use the SIMATIC NET V12 installation being enclosed to WinCC V7.3 if no
STEP 7 or TIA Portal is installed on the computer. (With it the communication
drivers are installed.)
10/2014
2 Solution
2.2 Hardware and software components
Table 2-3
Component
Note
Getting Started
S7-1500
101908495_WinCC_S71200_S71500_Chanel_de.pdf
This document.
color_filling_station.zip
10/2014
3.1
Action
Opening a WinCC project
Create a new WinCC project or open an existing one.
10/2014
Action
Right-click and add a "New Connection".
10/2014
10
Action
Optional: Realize a protected connection to S7-1500 by entering a password.
Note
Password protection is only provided by S7-1500 CPUs. Further information is
available in the manual:
"SIMATIC S7-1500 Automation System > Protection > Configuring access
protection for the CPU" \3\
10/2014
11
Action
Reading AS symbols
Right-click on the connection and go to "AS Symbols -> Read from AS" to read
out the symbols of the S7-1500.
10/2014
12
Process
Action
The symbols of the S7-1500 are now listed under "AS Symbols":
10
By checking the "Access" check box, the tags with symbolic addressing are
automatically created.
11
These are now displayed on the "Tags" tab together with their properties.
10/2014
13
12
Action
You can change the tag name on the "Tags" and "AS Symbols" tabs.
Note
Note
10/2014
14
3.2
1.
Action
10/2014
15
Process
Action
2.
3.
10/2014
16
4.
Note
Action
Now the tabs "AS Messages" and "AS Text lists" are available.
10/2014
17
4 References
References
Table 4-1
Subject
Title
\1\
Siemens Industry
Online Support
http://support.automation.siemens.com
\2\
Download page of
the entry
http://support.automation.siemens.com/WW/view/en/101908495
\3\
S7-1500 Manual;
Access Protection
https://www.automation.siemens.com/mdm/default.aspx?DocVersionI
d=63956397195&TopicId=62467847691
History
Table 5-1
Version
Date
V1.0
10/2014
10/2014
Modifications
First version
18