Professional Documents
Culture Documents
Alabama Engineering University, Invertors, Prof - Dr.eng. Jonathan Taylor - Moon
Alabama Engineering University, Invertors, Prof - Dr.eng. Jonathan Taylor - Moon
2014
These 240 Volts output voltage (DC) photovoltaic system structure is actually the input of a three-phase
inverter and converts alternating current and increase the strain and later to replenish the network.
Lots of inverters are being produced around the clock, by different producers, each trying
to make their one be the best. They vary the specifications, the application and the size to further
accommodate the needs of the client. Some examples of important manufacturers can be found
below:
There are different types and configurations of these inverters and all depends on how the
PV modules are connected to the inverter. The finding that we can determine what is the
appropriate configuration is taken depending on the work and financial environment. If the
modules are not identical or does not operate under the same conditions, the maximum power
point (MPP) for each panel will be different and will result in a voltage-power feature more
maximum, which is considered a problem, since most algorithms for maximum power point
tracking (MPPT - Maximum Power Point Tracking) meet in a single point maximum local start.
If depending only on point MPP operating point is not, then it means that all power is
possible powered network. Therefore, this case must be studied in detail, to optimize power and
maximum performance.
Central inverters are ideal for large PV power plants but are also suitable for
largesized power plants installed in commercial or industrial buildings.
High efficiency, proven components, compact and modular design and a host of life cycle
services ensures ABB central inverters provide a rapid return on investment.
Based on this highly successful platform and the most widely used frequency converters on
the market the inverters are the most efficient and cost-effective way to convert the direct
current (DC) generated by solar modules into high-quality and CO2-free alternating current
(AC) that can be fed into the power distribution network.
Multi-series inverter
In this case, each series is connected to a different DC converter dealing with maximum power
point tracking number, and all converters are connected to a single inverter, as shown in Figure
2.23. Advantages regarding MPPT inverter are the same as in series, each series has its own so
the maximum power point. Some disadvantages of an increase in production costs compared to
central inverter for use in addition and converters for each series.
A power inverter device which produces a multiple step sinusoidal AC waveform is referred to
as a sine wave inverter. To more clearly distinguish the inverters with outputs of much less
distortion than the "modified sine wave" (three step) inverter designs, the manufacturers often
use the phrase pure sine wave inverter. Almost all consumer grade inverters that are sold as a
"pure sine wave inverter" do not produce a smooth sine wave output at all, just a less choppy
output than the square wave (one step) and modified sine wave (three step) inverters. In this
sense, the phrases "Pure sine wave" or "sine wave inverter" are misleading to the consumer.
However, this is not critical for most electronics as they deal with the output quite well.
Where power inverter devices substitute for standard line power, a sine wave output is desirable
because many electrical products are engineered to work best with a sine wave AC power source.
The standard electric utility power attempts to provide a power source that is a good
approximation of a sine wave.
Sine wave inverters with more than three steps in the wave output are more complex and have
significantly higher cost than a modified sine wave, with only three steps, or square wave (one
step) types of the same power handling. Switch-mode power supply (SMPS) devices, such as
personal computers or DVD players, function on quality modified sine wave power. AC motors
directly operated on non-sinusoidal power may produce extra heat, may have different
speedtorque characteristics, or may produce more audible noise than when running on sinusoidal
power.
Output frequency
The AC output frequency of a power inverter device is usually the same as standard power line
frequency, 50 or 60 hertz
If the output of the device or circuit is to be further conditioned (for example stepped up) then the
frequency may be much higher for good transformer efficiency.
Output voltage
The AC output voltage of a power inverter device is often the same as the standard power line
voltage, such as household 120 VAC or 240 VAC. This allows the inverter to power numerous
types of equipment designed to operate off the standard line power.
The designed-for output voltage is often provided as a regulated output. That is, changes in the
load the inverter is driving will not result in an output voltage change from the inverter.
In a sophisticated inverter, the output voltage may be selectable or even continuously variable.
Output power
A power inverter will often have an overall power rating expressed in wats or kilowatts. This
describes the power that will be available to the device the inverter is driving and, indirectly, the
power that will be needed from the DC source. Smaller popular consumer and commercial
devices designed to mimic line power typically range from 150 to 3000 watts.
Not all inverter applications are primarily concerned with brute power delivery; in some cases
the frequency and or waveform properties are used by the follow-on circuit or device.
Batteries
The runtime of an inverter is dependent on the battery power and the amount of power being
drawn from the inverter at a given time. As the amount of equipment using the inverter increases,
the runtime will decrease. In order to prolong the runtime of an inverter, additional batteries can
be added to the inverter.
When attempting to add more batteries to an inverter, there are two basic options for installation:
Series Configuration and Parallel Configuration.
Series configuration
If the goal is to increase the overall voltage of the inverter, one can daisy chain batteries in a
Series Configuration. In a Series Configuration, if a single battery dies, the other batteries will
not be able to power the load.
Parallel configuration
If the goal is to increase capacity and prolong the runtime of the inverter, batteries can be
connected in parallel. This increases the overall Ampere-hour(Ah) rating of the battery set.
If a single battery is discharged though, the other batteries will then discharge through it. This
can lead to rapid discharge of the entire pack, or even an over-current and possible fire. To avoid
this, large paralleled batteries may be connected via diodes or intelligent monitoring with
automatic switching to isolate an under-voltage battery from the others.
Inverter designed to provide 115 VAC from the 12 VDC source provided in an automobile. The unit shown
provides up to 1.2 amperes of alternating current, or enough to power two sixty watt light bulbs.
An inverter converts the DC electricity from sources such as batteries or fuel cells to AC
electricity. The electricity can be at any required voltage; in particular it can operate AC
equipment designed for mains operation, or rectified to produce DC at any desired voltage.
Power grid
Grid-tied inverters are designed to feed into the electric power distribution system. They transfer
synchronously with the line and have as little harmonic content as possible. They also need a
means of detecting the presence of utility power for safety reasons, so as not to continue to
dangerously feed power to the grid during a power outage.
Solar
Main article: Solar inverter
A solar inverter is a balance of system (BOS) component of a photovoltaic system and can be
used for both, grid-connected and off-grid systems. Solar inverters have special functions
adapted for use with photovoltaic arrays, including maximum power point tracking and
antiislanding protection. Solar micro-inverters differ from conventional converters, as an
individual micro-converter is attached to each solar panel. This can improve the overall
efficiency of the system. The output from several microinverters is then combined and often fed
to the electrical grid.
Induction heating
Inverters convert low frequency main AC power to higher frequency for use in induction heating.
To do this, AC power is first rectified to provide DC power. The inverter then changes the DC
power to high frequency AC power. Due to the reduction in the number of DC Sources
employed, the structure becomes more reliable and the output voltage has higher resolution due
to an increase in the number of steps so that the reference sinusoidal voltage can be better
achieved. This configuration has recently become very popular in AC power supply and
adjustable speed drive applications. This new inverter can avoid extra clamping diodes or voltage
balancing capacitors. There are three kinds of level shifted modulation techniques, namely:
Phase Opposition Disposition (POD)
Alternative Phase Opposition Disposition (APOD)
Phase Disposition (PD)
Electroshock weapons
Electroshock weapons and tasers have a DC/AC inverter to generate several tens of thousands of
V AC out of a small 9 V DC battery. First the 9 V DC is converted to 4002000 V AC with a
compact high frequency transformer, which is then rectified and temporarily stored in a high
voltage capacitor until a pre-set threshold voltage is reached. When the threshold (set by way of
an airgap or TRIAC) is reached, the capacitor dumps its entire load into a pulse transformer
which then steps it up to its final output voltage of 2060 kV. A variant of the principle is also
used in electronic flash and bug zappers, though they rely on a capacitor-based voltage multiplier
to achieve their high voltage.
Miscellaneous
Typical applications for power inverters include:
Portable consumer devices that allow the user to connect a battery, or set of batteries, to
the device to produce AC power to run various electrical items such as lights, televisions,
kitchen appliances, and power tools.
Use in power generation systems such as electric utility companies or solar generating
systems to convert DC power to AC power.
Use within any larger electronic system where an engineering need exists for deriving an
AC source from a DC source.
\\\