Professional Documents
Culture Documents
Set Advanced Channel Management Parameters of Cell
Set Advanced Channel Management Parameters of Cell
Parameter
Name
IDTYPE
Index Type
Parameter Description
Unit: None
Parameter ID
Parameter
Name
CELLID
Cell Index
Parameter Description
Unit: None
Cell Name
Meaning: Name of a cell,
uniquely identifying a cell in a
BSC
Parameter ID
Parameter
Name
Parameter Description
Unit: None
TCH Traffic
Busy Threshold Meaning: If the current channel
seizure ratio reaches or exceeds
this value, the half-rate TCH is
assigned preferentially;
otherwise, the full-rate TCH is
assigned preferentially.
Recommended Value: 60
INTERFPRIALLOW
Interf. Priority
Allowed
Parameter ID
Parameter
Name
Parameter Description
Unit: None
Active CH
Interf.
Meas.Allowed
Parameter ID
Parameter
Name
Parameter Description
YES(Yes)
Unit: None
Allocation
TRX Priority
Allowed
Parameter ID
Parameter
Name
Parameter Description
Unit: None
History Record
Priority
Meaning: Whether to consider
Allowed
history priority records during
channel assignment.
If this parameter is set to YES,
the history priority records are
considered. If this parameter is
set to NO, the history priority
records are not considered.
Unit: None
Parameter ID
Parameter
Name
Parameter Description
Balance Traffic
Allowed
Meaning: If this parameter is
set to YES, the channel
assignment algorithm II
randomly selects the start range
for channel traversal; otherwise,
the algorithm selects the
channel next to the channel
assigned last time as the start
point of channel traversal.
Unit: None
Interf.of UL
Level
Threshold
Parameter ID
Parameter
Name
Parameter Description
Unit: dB
Recommended Value: 30
UPINTERFQUALLIMIT
Interf.of UL
Qual.
Threshold
Parameter ID
Parameter
Name
Parameter Description
Unit: None
Recommended Value: 40
DLINTERFLEVLIMIT
Interf.of DL
Level
Threshold
Unit: dB
Parameter ID
Parameter
Name
Parameter Description
Recommended Value: 35
DLINTERFQUALLIMIT
Interf.of DL
Qual.Threshold Meaning: Threshold for
determining whether downlink
interference exists. If the
downlink level is equal to or
greater than Interf.of DL Level
Threshold and the downlink
quality level is equal to or
greater than Interf.of DL
Qual.Threshold, downlink
interference exists.
Unit: None
Recommended Value: 40
SSLENSD
Filter Length
for TCH Level
Parameter ID
Parameter
Name
Parameter Description
Unit: ms
Recommended Value: 6
QLENSD
Filter Length
for TCH Qual.
Parameter ID
Parameter
Name
Parameter Description
Unit: ms
Recommended Value: 6
SSLENSI
Filter Length
for SDCCH
Level
Parameter ID
Parameter
Name
Parameter Description
Unit: ms
Recommended Value: 2
QLENSI
Filter Length
for SDCCH
Qual.
Parameter ID
Parameter
Name
Parameter Description
channels.
Unit: ms
Recommended Value: 2
AMRTCHHPRIORALLOW
AMR TCH/H
Prior Allowed
Parameter ID
Parameter
Name
Parameter Description
Unit: None
Recommended Value: ON
AMRTCHHPRIORLOAD
AMR TCH/H
Prior Cell Load Meaning: Load threshold for
Threshold
assigning half rate channels
preferentially. If the current
TCH seizure ratio of the cell is
greater than this threshold,
AMR half rate channels are
assigned preferentially.
Parameter ID
Parameter
Name
Parameter Description
Recommended Value: 55
TCHTRICBUSYOVERLAYTHR
Tch Traffic
Busy Overlay
Threshold
Parameter ID
Parameter
Name
Parameter Description
Recommended Value: 70
TCHTRIBUSYUNDERLAYTHR
Tch Traffic
Busy Underlay
Threshold
Parameter ID
Parameter
Name
Parameter Description
Recommended Value: 60
HRIUOLDRATESELALLOW
Load of UL-OL
Cells Rate
Meaning: Whether to enable the
Select Allowed BSC to assign half or full rate
channels to MSs according to
the channel seizure ratio in the
overlaid and underlaid subcells
Unit: None
Smooth Factor
of Uplink
Meaning: After the existing
Received Level uplink receive level, uplink
receive level after the previous
optimization, and the value of
this parameter are weight-
Parameter ID
Parameter
Name
Parameter Description
Unit: None
Recommended Value: 6
UPRXLEVLASTTIME
Duration of
Uplink
Meaning: If the difference
Received Level between uplink receive levels
Differ
of calls within the same
timeslot is greater than Offset
of the difference between
uplink received levels for P
seconds among N seconds, the
call with weak uplink receive
level within the timeslot will be
handed over to another timeslot.
This parameter corresponds to
Parameter ID
Parameter
Name
Parameter Description
Unit: s
Recommended Value: 4
UPRXLEVSTATICTIME
Observe Time
of UL RX
Level
Difference
Parameter ID
Parameter
Name
Parameter Description
Unit: s
Recommended Value: 5
QTRUPWRSHARE
Multi-Density
TRX Power
Sharing
Unit: None
Parameter ID
Parameter
Name
Parameter Description
MCPA
Optimization
Switch
Unit: None
Qtru Down
Power
Meaning: The P/N criteria is
Inadequate Stat used to determine low downlink
Time
power for multi-density
carriers. If the downlink power
of a multi-density carrier
remains low during a
consecutive P seconds out of N
seconds, the downlink power of
the multi-density carrier is
considered low. This parameter
Parameter ID
Parameter
Name
Parameter Description
Unit: s
Recommended Value: 5
QTRUDNPWRLASTTIME
Qtru Down
Power
Meaning: The P/N criteria is
Inadequate Last used to determine low downlink
Time
power for multi-density
carriers. If the downlink power
of a multi-density carrier
remains low during a
consecutive P seconds out of N
seconds, the downlink power of
the multi-density carrier is
considered low. This parameter
corresponds to the P in the P/N
criteria.
Parameter ID
Parameter
Name
Parameter Description
Unit: s
Recommended Value: 3
PWRPRIORALLOW
Power Priority
Allowed
Unit: None
Parameter ID
Parameter
Name
Parameter Description
Level Thresh
for Assign
BCCH Under
TBCCH
Parameter ID
Parameter
Name
Parameter Description
Unit: dB
Recommended Value: 30
TIGHTBCCHASSMAINBCCHQUAL
Quality Thresh
for Assign
BCCH Under
TBCCH
Parameter ID
Parameter
Name
Parameter Description
of TIGHT BCCH.
Unit: None
Recommended Value: 1
CHPWRINSUFFALLOWED
Channel Assign
Allow for
Meaning: Whether to allow a
Insuff Power
multi-density TRX board, that
uses the dynamic power sharing
algorithm to assign channels, to
assign a channel to an MS when
the remaining power on the
multi-density TRX board is less
than the power required by the
MS. If this parameter is set to
YES, a multi-density TRX
board that uses the dynamic
power sharing algorithm to
assign channels cannot assign a
channel to an MS when the
remaining power on the multidensity TRX board is less than
the power required by the MS.If
this parameter is set to NO, a
Parameter ID
Parameter
Name
Parameter Description
Unit: None
Recommended Value: NO
FREQLOADSHARETRAFFTHRSH
GSM900 Band
Traffic Load
Share
Threshold
Parameter ID
Parameter
Name
Parameter Description
Recommended Value: 25
NAMRLFRMTRXALLOWED
Meaning: Whether to
preferentially allocate loose
multiplexing frequencies to
Parameter ID
Parameter
Name
Parameter Description
non-AMR users
Unit: None
Recommended Value: NO
IBCAALLOWED
IBCA Allowed
Meaning: Whether to enable the
IBCA algorithm
Unit: None
Parameter ID
Parameter
Name
Parameter Description
Recommended Value: NO
IBCAUSRDYNCMEASURENCELL
IBCA User
Dyn Measure
Neighbor Cell
Unit: None
Parameter ID
Parameter
Name
Parameter Description
Recommended Value: NO
IBCAUSEDIUOSUBLAY
IUO IBCA
Allowed
Unit: None
IBCA Soft
Block Switch
Parameter ID
Parameter
Name
Parameter Description
assignment
Unit: None
Recommended Value: NO
IBCAFRSOFTBLKTHRD
IBCA FR/EFR
Soft Block
Threshold
Parameter ID
Parameter
Name
Parameter Description
Unit: dB
Recommended Value: 10
IBCAHRSOFTBLKTHRD
IBCA HR Soft
Block
Threshold
Parameter ID
Parameter
Name
Parameter Description
Unit: dB
Recommended Value: 13
IBCAAFRSOFTBLKTHRD
IBCA AMR FR
Soft Block
Meaning: Minimum C/I ratio
Threshold
that IBCA AMR FR services
allow. An idle channel can be
assigned to such a service only
when the C/I ratio of the idle
channel is greater than this
threshold. In addition, a new
call associated with such a
service can be established only
when the call does not decrease
the C/I ratio of the established
calls to a value less than this
threshold.
Unit: dB
Parameter ID
Parameter
Name
Parameter Description
Recommended Value: 4
IBCAAHRSOFTBLKTHRD
IBCA AMR
HR Soft Block
Threshold
Unit: dB
Recommended Value: 10
IBCAWAFRSOFTBLKTHRD
IBCA WAMR
FR Soft Block
Parameter ID
Parameter
Name
Parameter Description
Threshold
that can be tolerated by IBCA
WAMR FR. The C/I ratio of an
idle channel must be larger than
this parameter. Otherwise, it
cannot be assigned. In addition,
the system does not allow a
newly-established call causing
the C/I ratio of existing calls to
be lower than this parameter.
Unit: dB
Recommended Value: 5
IBCASOFTBLKSAICOFF
IBCA Soft
Block SAIC
Offset
Parameter ID
Parameter
Name
Parameter Description
Unit: dB
Recommended Value: 1
IBCAMAXINTFSRCNUM
IBCA Max.
Interference
Source Num.
Unit: None
Parameter ID
Parameter
Name
Parameter Description
Recommended Value: 20
IBCADLPATHLOSSOFF
IBCA
Downlink Path
Loss Offset
Unit: dB
Parameter ID
Parameter
Name
Parameter Description
Recommended Value: 7
IBCAIUOPATHLOSSOFF
Unit: dB
Parameter ID
Parameter
Name
Parameter Description
Recommended Value: 4
IBCASCELLPATHLOSS
IBCA Service
Cell Pathloss
Unit: dB
IBCA Pathloss
Offset
Parameter ID
Parameter
Name
Parameter Description
Unit: dB
Recommended Value: It is
recommended that you set the
path loss offset of layer 1
neighboring cells of the serving
cell to 15 dB and that of other
neighboring cells to 25 dB.
IBCACALLINFOFILTERLEN
IBCA Call
Information
Filter
Meaning: Number of
measurement reports sampled
for averaging path loss. A single
measurement report may not
reflect the actual network
situations accurately. Therefore,
the BSC needs to average the
measured values in several
successive measurement reports
to reflect the radio environment.
Parameter ID
Parameter
Name
Parameter Description
Unit: ms
Recommended Value: 4
LOOSESDCCHLOADTHRED
IBCA Loose
Trx SDCCH
Meaning: When the load of an
Load Threshold SDCCH on the TRX that is in
loose frequency reuse and is in
the compatible band of the
BCCH is lower than this
threshold, the SDCCH is
preferably allocated.
Parameter ID
Parameter
Name
Parameter Description
Recommended Value: 80
TIGHTSDCCHRXLEVTHRED
Unit: dB
Recommended Value: 40
Parameter ID
Parameter
Name
WAITSDCCHIDLETIMER
IBCA Wait
SDCCH Idle
Timer
Parameter Description
Unit: s
Recommended Value: 4
IBCAICDMSWITCH
IBCA ICDM
Switch
Parameter ID
Parameter
Name
Parameter Description
IBCA algorithm.
Unit: None
IBCA Path
Lose Filter
Factor
Parameter ID
Parameter
Name
Parameter Description
Unit: None
Recommended Value: 6
IBCANCELLPATHLOSSESTIMATE
IBCA Pathloss
Est of Non. MR Meaning: Estimates the receive
Ncell
level of the unmeasured IBCA
neighboring cells. When a
consecutive IBCA Non
Measurement Ncell Stat. Num
measurement reports cover less
than six neighboring cells (or
the number of the reported
neighboring cells is smaller
than that of the actually
configured neighboring cells),
this parameter is used to
estimate the receive level of the
unmeasured IBCA neighboring
cells. The estimated value is
IBCA Pathloss Est of Non.
MR Ncell. Otherwise, the
signal strength of the
unmeasured IBCA neighboring
cells is the signal strength of the
measured neighboring cells
(including non-IBCA
neighboring cells) subtracted by
IBCA RxLev Offset.
Parameter ID
Parameter
Name
Parameter Description
Unit: dB
Recommended Value: 0
IBCANONMEANCELLSTATNUM
IBCA Non
Measurement
Ncell Stat.
Num
Parameter ID
Parameter
Name
Parameter Description
Unit: None
Recommended Value: 4
IBCAMAIOUSMTD
IBCA MAIO
Using Method
Parameter ID
Parameter
Name
Parameter Description
Unit: None
Recommended Value: 0
IBCATARGETCIRTHRSH
IBCA MAIO
Target C/I
Threshold
Unit: None
Parameter ID
Parameter
Name
Parameter Description
Recommended Value: 20
IBCAINITPCRXLEVDLOFFSET
IBCA Init.
Power Control
RexLevDL
Offset
Unit: dB
Recommended Value: 0
IBCAINITPCRXLEVULOFFSET
IBCA Init.
Power Control
RexLevUL
Offset
Parameter ID
Parameter
Name
Parameter Description
Unit: dB
Recommended Value: 0
IBCAINITPCRXQUALDLOFFSET
Unit: dB
Parameter ID
Parameter
Name
Parameter Description
Recommended Value: 0
IBCAINITPCRXQUALULOFFSET
Unit: dB
Recommended Value: 0
LOWRXLEVOLFORBIDSWITCH
Allocate OL
Channel Based
on RX Level
Parameter ID
Parameter
Name
Parameter Description
conditions
Unit: None
Assign to
Overlayer
RxLev Offset
Parameter ID
Parameter
Name
Parameter Description
Unit: dB
Recommended Value: 35
HOOLRXLEVOFFSET
Handover to
Overlayer
RxLev Offset
Parameter ID
Parameter
Name
Parameter Description
Unit: dB
Recommended Value: 32
IBCASUBCHNHANDOVERALLOWED
IBCA SubChannel
Handover
Allowed
Parameter ID
Parameter
Name
Parameter Description
Unit: None
IBCA Forced
BTS
Synchronizatio
n Allowed
Parameter ID
Parameter
Name
Parameter Description
synchronization.
Unit: None
IBCA Flexible
TSC Allowed
Parameter ID
Parameter
Name
Parameter Description
Unit: None
IBCA Assign
Waiting Mr
Time
Unit: s
Parameter ID
Parameter
Name
Parameter Description
Recommended Value: 4
IBCANHOASSWAITMEASURERPTTIM
E
IBCA Natural
HO Waiting Mr Meaning: Length of the timer
Time
for a call to measure the path
loss in the neighboring cell with
strong interference of the target
cell. The call to be handed over
needs to measure the path loss
before initiating the handover to
the target cell when dynamic
measurement of the BA2 list is
enabled during the normal
handover. When this parameter
is set to 0, dynamic
measurement of the BA2 list is
not enabled in the normal
handover, and the parameter
"Wait Time for Valid MRs in
IBCA HO" is invalid.
Unit: s
Parameter ID
Parameter
Name
Parameter Description
Recommended Value: 5
IBCAEHOASSWAITMEASURERPTTIM
E
IBCA Urgent
HO Waiting Mr Meaning: Length of the timer
Time
for a call to measure the path
loss in the neighboring cell with
strong interference of the target
cell. The call to be handed over
needs to measure the path loss
before initiating the handover to
the target cell when dynamic
measurement of the BA2 list is
enabled during the emergency
handover. When this parameter
is set to 0, dynamic
measurement of the BA2 list is
not enabled in the emergency
handover, and the parameter
"Wait Time for Valid MRs in
IBCA HO" is invalid.
Unit: s
Parameter ID
Parameter
Name
Parameter Description
Recommended Value: 0
IBCAHOASSWAITMEASURERPTTIME
IBCA HO
Waiting
Effective Mr
Time
Unit: s
Recommended Value: 2
Parameter ID
Parameter
Name
CIRESTVALUE
C/I Estimate
Value
Parameter Description
Unit: dB
Recommended Value: 22
IBCANEWCALLCIROFFSET
Target CIR
Offset of IBCA Meaning: When the IBCA
New Call
algorithm is enabled, this
parameter is used to calculate
the target CIR of a new call.
The formula is as follows:
Target CIR of a new call =
Target CIR in use + Target CIR
Offset of IBCA New Call
Parameter ID
Parameter
Name
Parameter Description
Unit: dB
Recommended Value: 7
IBCAOPRREVISEFACTOR
Corrected
Factor of IBCA Meaning: When the IBCA
Priority
algorithm is enabled and the
HSN is not 0, the IBCA priority
and the SDCCH/PDCH priority
are divided by this corrected
factor respectively to reduce the
weight of IBCA priority. In
addition, the priority of the
interference band is considered.
Unit: None
Parameter ID
Parameter
Name
Parameter Description
Recommended Value: 0
IBCACALLTARGETCIROFFSET
Target CIR
Offset of IBCA Meaning: When the IBCA
Set-up Call
algorithm is enabled, this
parameter is used to calculate
the target CIR of an existing
call. The formula is as follows:
Target CIR of an existing call =
Target CIR in use + Target CIR
Offset of IBCA Set-Up Call.
Unit: dB
Recommended Value: 4
IBCACALLSOFTBLOCKTHOFFSET
IBCA Set-up
Call Soft Block Meaning: When the IBCA
Threshold
algorithm is enabled, this
Offset
parameter is used to calculate
Parameter ID
Parameter
Name
Parameter Description
Unit: dB
Recommended Value: 0
IBCAICDMRELEVOFFSET
IBCA ICDM
Initial Level
Offset
Parameter ID
Parameter
Name
Parameter Description
Unit: dB
Recommended Value: 10
CELLOPPWRGRP
Cell Operator
Power Group
Parameter ID
Parameter
Name
Parameter Description
Unit: None
Type of Cell
Load
Calculation
Unit: None
Parameter ID
Parameter
Name
Parameter Description
Recommended Value:
DYNPDCHASIDLE
Example
To set the advanced channel management parameters of the cell (Index Type =
BYID;
Cell Index = 0; TCH Traffic Busy Threshold = 100), run the following command:
SET GCELLCHMGAD: IDTYPE=BYID, CELLID=0, TCHBUSYTHRES=100;