Professional Documents
Culture Documents
Manual Gaoke
Manual Gaoke
Users Manual
We are enthusiastic for providing tech support in every way. You can get in touch with
Gaoke bureau contiguously as well as contact to Customer Service Department directly.
Version declaration
Copyright by Guangzhou Gaoke Communications Technology Company Limited.
All rights are reserved.
No Part of this document may be reproduced or transmitted in any form or by any means without
prior written consent of Guangzhou Gaoke Communications Technology Company Limited.
Irresponsible declaration
Guangzhou Gaoke Communications Technology Company Limited reserves the right to change
the document from time to time at its sole discretion, and not to make the notice to anyone in
advance.
Prolegomenon
Version instruction
This Manual is provided for MG6000 series Media Gateway, which are called as IAD.
Products included: MG6002(2)MG6004EMG6008MG6008EMG6016MG6016EMG6032
MG6002ETMG6004ET and MG6008ET. All these products support SIP protocol.
Reader
Network manager.
Network engineer.
Technology expanding people.
Appointment
Table 1 appointment of graphic interface style
Style
\
Meanings
Multi-grade catalogue or menu are segregated by\.For example,
file\new\folder means the menu item of file->new->folder.
Used for identifying function area in the picture.
<>
{ XX | XX }
For instance:
tftp host {get | put} {sys | cfg} filename
hostitalic
THE ACTUALLY METHODS OF USING MAYBE IS:
tftp 138.0.0.102 get sys mg6004.img
Table 2
Operation
Click
Double click
Drag
Meanings
Press and release a mouse button quickly
Quickly press and release a mouse button twice
Press a mouse button and move the mouse
Table 3
Style
Ctrl + C
Meanings
+means press multiple keys in keyboard at the same time to accomplish an
operation. SoCtrl + Cmeans to press Ctrl and C at the same time.
Symbols
The manual uses some symbols refreshing to see:
Attention:
Remind some announcements of operations.
Instruction:
Footnote some operations.
Contents
1 SUMMARY ................................................................................3
1.1 DEFINITIONS AND ABBREVIATION .........................................................3
1.2 CLI NETWORK MANAGEMENT..............................................................3
1.3 WEB NETWORK MANAGEMENT..............................................................4
2 INTRODUCTION OF DEVICE.................................................................5
2.1 MG6002(2) INTRODUCTION .............................................................5
2.1.1 CONTOUR GRAPHIC ..............................................................................................................................5
2.1.2 DEVICE FRONT PANEL ..........................................................................................................................6
2.1.3 DEVICE BACK PANEL ............................................................................................................................6
2.1.4 SETTING ...............................................................................................................................................7
2.2 INTRODUCTION OF MG6004 .............................................................7
2.2.1
APPEARANCE .................................................................................................................................7
- 2 -
1 Summary
This manual will help you learn how to operate and manage your MG6000 media gateway and make the best
use of its many upgraded features including simple and quick installation.
1.1
1.2
CLI Management is one Network management supported by IAD. Users could log in the CLI by Super terminal
or Telnet user terminals to configure and manage equipment remotely by command-line approach.
- 3 -
1.3
Server
Browser
HTTP
Equipment
- 4 -
2 Introduction of Device
MG6000 series media gateway are based on IP networks, which supports PPPoE DHCP protocol and
provides an ideal solution for voice and fax transmission. All products support updating firmware online, and can
be set by iGoViewweb or CLI.
IAD product is an integrated access devices which supports PPPoE, DHCP protocol, based on IP networks.
IP networks can achieve high-quality telephone, fax and other business. IAD product has good interoperability
and is widely used in the network, broadband MAN which formed by Ethernet switches and routers. IAD
product has CND, billing functions and supports TFTP softwares upgrade online, available through iGoView,
WEB, CLI three ways network management, user-friendly, easy to operate.
2.1
MG6002(2) introduction
MG6002 (2) has anti-PING attack function to keep the equipment away from unlawful packet attacks on the
network and the firewall function will also be gradually improved in the follow-up version. The shape and panel
both front and back of MG6002ET are the same with MG6002 (2), the only difference is that MG6002ET has
FXS port, but no FXO port.
2.1.1
Contour graphic
- 5 -
Instruction
Phone interface by matching the FXS mouth or FXO can not be told directly from the appearance, it need to be
read from network management.
2.1.4
Setting
In order to set up equipment more easily, MG6002 (2) has been set up two groups of digital switch: mandatory
follow-switching PSTN calland the system started selection switch. PSTN switch is in the back panel. When the
switch transfers to PSTN, compulsorily, all outbound calls of FXS mouth will be transferred to FXO through
PSTN; when the switch transfers to VoIP, uncompulsorily, all outbound calls of FXS mouth will pass VoIP or
PSTN will be divided by the dail setted by the equipment. System starting the choosing switch is to manage
network if the IP addressof equipments is unknown and cannot been connected. Usually it doesnt need to be set,
the system-choose switch is inside the equipment and its not able to set up directly. The switch is call-switching
with 4 positions.
The digital switch-activated system of choice with the results and equipment port configuration is shown in Fig
2-2:
Position
1
2
Sheet 2-1
Values
Description
ON
OFF
ON
Use default IP
OFF
3,4
configuration settings
2.2
Introduction of MG6004
MG6004 is a single board, the appearance is exquisite and light and the maximum capacity is four lines, the
users interface type can only be FXS; MG6004 also has two 10/100 Base-T Ethernet interface, with two-story
wire-speed switching functions, users can save hubs (switch). In addition, a 10M I is saved for backup.
2.2.1
Appearance
- 7 -
Fig.2-5
2.2.2
Appearance of MG6004 ET
- 8 -
2.3
MG6008 introduction
MG6008 is a single board structure, the maximum capacity is 8 lines. MG6008 have 2 types: MG6008 and
MG6008-ET.
The interface type of MG6008-ET user can only be FXS; MG6008-ET also has two 10/100Base-T Ethernet ports,
supporting auto-negotiation and 2-layer string speed switch function which could save hubs (switch) for users.
Meanwhile it has a 10 Base-T port for billing.
2.3.1 Appearance
Fig.2-10
Appearance of MG6008
- 9 -
Fig.2-11
2.3.2
Appearance of MG6008 ET
- 10 -
Power socket
Power button
Fig.2-15 MG6008 back panel
Fig.2-15 shows MG6008 back panel.
a) Power button: power up the device when press the switch, or power down;
b) Power socket: 2.1mm small AC outlet, +12V DC power supply;
c) Phone: POTS port of 4 lines FXS or FXO, RJ-11,after choosing FXS and FXO interface ,the
configuration will be fixed when leave factory;
d) RS232 interface: interface type RJ-11, used for setting data;
e) 10/100Base-T: two 10/100Base-T Ethernet ports, supporting auto-negotiation. The port type is RJ-45.
2-layer string speed switch function lies in the two ports;
- 11 -
2.4
MG6016 introduction
speed switch function which could save hubs (switch) for users. In addition ,it provides
10M Ethernet for billing and could send CDR to the network management computer with IP address of private network
address and save the public network address.
The user interface type of MG6016E can only be FXS; MG6016E also has two 10/100Base-T Ethernet ports,
supporting auto-negotiation and 2-layer string speed switch function which could save hubs (switch) for users.
Meanwhile it has a 10 Base-T port for billing.
2.4.1 Appearance
Fig.2-18
2.4.2
Appearance of MG6016
2.5
MG6032 introduction
MG6008 is a multiboard structure, the maximum capacity is 32 lines. The user interface (FXS or FXO) could be FXS
32 or 16FXS16FXO; MG6032 also has 4 10/100Base-T Ethernet ports, supporting auto-negotiation and 2-layer
string speed switch function which could save hubs (switch) for users.
2.5.1 Appearance
- 13 -
Appearance of MG6032
The style is the same with MG6016/24 front panel, shown as fig.2-22.
b) RUN: Working status indicator, green. Flashing when its being supply with power. Being on or off means
the device is not working properly;
c) ALM: alarm systems indicator, being on when the system does not operate normally;
d) BUSY: board work indicator, being on when the board is detected and it worked in a normal state;
e) U1 :NO.1-16 pick and hang up indicator;
f) U2 :NO.17-32 pick and hang up indicator;
g) restore the default configuration button, when the device launchs, pressing this button for more than 15 seconds, the
device will recover to the default configuration.
2.5.3
Considering that the MG6032 can be flexibly configured to 16 IAD, the back
the interface (RJ-45 or RJ-21)is optional, the configuration is scheduled by the user. Shown as Fig 2-23 and 2-24.
- 15 -
MG6008ET is 138.0.60.1. Because if the equipment IP address and network management computer IP address is not in
the same network segment, the network management computer can not access to equipments. Therefore, when the
equipment is used the first time, users must change the IP address of device to adapt to the LAN, just like the network
179.0. Xx.xx need to replace to 179.0. Xx.xx.
The system offers two methods of setting IP addresses, then take MG6004E for an example. After the IP address
of the equipment has been set up could test whether the network management computer and device are connecting
normally by using ping order.
Attention
In order to change the IP address, the new IP address will effect when restore and re-start.
- 16 -
3.1.1
Security configuration
Click tools/internet option/security to enter security configuration in IE browser. Its shown as Fig 3-3.
- 17 -
LAN configuration
When user access equipment network management through LAN please refer to this, or neglect.
Users can click tools/internet options/LAN Settings to enter LAN configuration page as Fig 3-5 and Fig
3-6.
- 18 -
3.1.3
Access configuration
- 19 -
3.2
3.2.1
CLI configuration
The most convenient configuration environment is shown as Fig 3-8. IAD and computer are connected by IP
network directly.
Serial
port/Ethernet
MG6008
3 COM
Li nk swit ch
3 00 0
PC
Fig 3-8 CLI network management simple configuration environment
MG6004E provides three Ethernet, we can use any link network management stations, and the connection to network
management station can use the straight / cross-network lines. MG6016/MG6024 provides two 10/100 Base-T and a 10
Base-T, any port of the two 10/100 Base-T can connect with the network management station and can use the straight /
cross-network lines.
3.2.2
Subscriber can access MG6008 through Hyper Terminal or client of Telnet. The default IP address of IAD is
138.0.60.1.
- 20 -
Connect computer and IAD with RS232 interface, and use Hyper Terminal software as command operation
interface to implement access and configuration. Including IP address parameter, Take MG6008 as the example,
the step is:
a). Connect COM 1 port of computer and IAD RS232 port with serial line (this line is an accessory of IAD);
b). Click start//Hyper terminal to run Hyper terminal program. Input connection name in Name box; as
shown in Fig 3-9 a);
c). Set computer COM port number in connect using box. as shown in Fig 3-9 b;
d). Click Restore Default to use default parameters to communicate with the device. Click Ok button to
enter Hyper terminal. As shown in Fig 3-9c;
e). Press the key Enter, the command prompt MG6008> will be show in workspace. As shown in Fig 3-9
d;
f). Input enable after MG6008>, and input password gaoke (Default password) to enter privilege mode.
The prompt will show as MG6008#.
Login succeeds right now. Users can set and manage the device.
c) Port setting
d) IP address setting
- 21 -
Make sure that IAD and computer are all connecting to the same LAN first. Or connected by cable (Direct/Cross
Connect) directly, and host IP address and device is in the same subnet. For Windows systemits modified in the
cards TCP / IP parameters. Then take MG6008 for example.
a) Input telnet MG6008 IP address in start/run, and the window as Fig 3-10 will be
prompted;
b) Input password. The default password is admin, and user can modified it as explained in the
following chapter;
c) Press the key Enter, the command prompt MG6008>will show in workspace;
d) Input enable after MG6008> and input password to enter privilege mode. The prompt will
become MG6008# now. The default password of privilege mode is gaoke.
Now, users can manage the device.
- 22 -
Level of users
User ID
Passwords
Common
guest
guest
Senior
admin
admin
Super
super
super
User cannot modify the user name but the password. When the user attempts to browse the pages out of their
authorization, system will indicate the invalid operation by returning the page of logging in.
4.1.2 Operation of Logging in Web
Type http://xxx.xxx.xxx.xxx (xxx.xxx.xxx.xxx is the IP address of the IADs port which connect with the PC)
in IE to log in (figure 4-2). User cannot enter the main web management page unless typing the valid user name
and password.
Attention:
a)
b)
c)
4.2
- 24 -
This is the first screen when we log in the web management system. User can view the Current information
in it, includes device nameproduct revisionrevision dateDSP versionSIP versionstatic IP infoPPPoE
client infoDHCP client infoDHCP server infoline status info.
Click the Quit button on the upper right side to log off.
There are 13 menu items on configuration menu column on the left of the screen. They are shown below:
a) Network: Includes device network basic configuration (Static IP, DHCP Client, PPPoE Client) and
device network advanced configuration (DHCP Server, DNS Service, NTP Service, STUN, 802.1X,
802.1X);
b) SIP Protocol: parameter configuration about SIP Protocol.
c) Media Stream: parameter configuration about Audio Codec and DSP.
d) Line Config: parameter configuration about Gateway number prefixport number register Call
Forward incoming number echo and so on.
e) Digit Map: A form of routing configuration. It based on regular expression, and can configure several
routes once.
f) Route Table: previewadddelete and modify the route table.
g) VLAN Configparameter configuration about vlan
Only ET-type devices support this configuration
through WEB management system
h) Value-added: parameter configuration about Call-snatch Call-hold confidence call Three-Way
Calling and so on.
i) System Tools: includes the tools of configuration savingdefault configuration loadingSoftware
upgrade and so on.
j) Accounting: configuration about port permission accounting through the web port.
k) SNMP Config: configuration about SNMP parameter and alarm message.
l) Password: configuration about user password. There are three levels of users: common usersenior user
and super user
m) Device Info: the first screen when we log in the web management system. Its the Main screen.
Attention:
The number of the ports shown on the main screen will be different in types of device. For example,
MG6002 have 2 ports, MG6004 have 4 ports, MG6008 have 8 ports, MG6016 have 16 ports, and MG6032 have
32 ports.
- 25 -
.
Figure 4-4 User manage
After modifying the password, you must saved the current configuration and restart the IAD.
Attention:
a). Upper level users could modify the password of lower level users;
b). User could modify password but not user name;
c). The length of password is 3-30 characters.
- 26 -
All kinds of users could enter this page; All the users have the authorization to configure except common
users.
l Static IP
After modifying IP addresscurrent configuration must be saved, and then reboot the IAD.
Users should prevent network failure from using following addresses as IP: 0.x.x.x, 127.x.x.x, 255.x.x.x and
so on. For the same reason, net mask should avoid 0.0.0.0 and 255.255.255.255.
Connect IAD to the other network segment by setting default gateway. Through the gateway, data packets
will be sent to devices in another network segment. There is no need to use Enable Gateway if IAD do not
communicate with other network segments.
Attention:
Its forbidden to set the IP address of the WAN port and the LAN port in the same network segments.
DHCP Client
After modifying the parameter of DHCP Clientcurrent configuration must be saved, and then reboot
the IAD.
IAD is able to get IP address from DHCP server in the network. The service of DHCP must be started at
the same time of initializing the system; otherwise, the service cant be started again.
In this page, the parameters as following can be configured.
a) Enable DHCP client or not;
b) Use special DHCP server or not. That means the device only receive the message of the specified
server of DHCP;
c) Special DHCP server. Input the IP address of DHCP server that is special.
- 27 -
Attention
a).
If DHCP client get IP address successfully, the static IP of WAN port will be replaced by the dynamic IP
address which the DHCP client get. If user wants to log in web management system, you need to type
the dynamic IP that the DHCP client gets in IE.
b). After users start the DHCP, if the DHCP client is failed to communicate with the DHCP server, the IP
address cant be received so that the device cant be accessed through network. If that happened, users
have to forbid using the DHCP through the serial port, and configure fixed IP address and save the
configuration. You can use the new fixed IP address after reboot the device.
c). DHCP client and PPPoE client cant be enabled at the same time.
PPPoE Client
After modifying the parameter of PPPoE Clientcurrent configuration must be saved, and then reboot
the IAD.
IAD has built-in PPPoE client. It can dial into network after configuring ADSL user name, password,
server name (optional) and service name (optional) gotten from service providers. If the function of PPPoE
client is started, user cant make a call through IAD until the PPPoE client dial into network successfully.
But user still can connect the IADs Ethernet port and modify the parameter of PPPoE Client through web
management system.
IAD dials to PPPoE during initiation. It will redial until dial successfully. Authorization error wont lead
to redial. If the offline status is caused by line error, IAD will restart to dial again.
User can preview the information of PPPoE client on the page of Device info.
Attention:
a) /, *, $ and space are invalid character and can not be input.
b) DHCP client and PPPoE client cant be used at the same time.
c) MG6032 could not support the function of PPPoE Client.
- 28 -
All kinds of users could enter this page; all the users have the authorization to configure except common
users.
l
DHCP Server
After modifying the parameter of DHCP Servercurrent configuration must be saved, and then reboot
the IAD.
As a DHCP Server, IAD can provide IP address for DHCP clients in LAN.
In this page, the parameters as following can be configured:
a) Enable DHCP server or not: the parameters below can not be configured until enable the DHCP
service;
b) Start IP address: the start IP address that DHCP server provides for DHCP clients.
c) End IP address: the end IP address which DHCP server provides for DHCP clients.
d) Primary DNS Sever: the Primary DNS Sever address which the DHCP server provides for DHCP
clients.
e) Slave DNS Server (optional): the slave DNS Sever address which DHCP server provides for DHCP
clients
f) Default Gateway: the Default Gateway switch DHCP server provides for DHCP clients.
g) Subnet Mask: the Subnet Mask which DHCP server provides for DHCP clients.
Attention
a). IAD provide the function of DHCP server through the LAN port. Users need to connect the DHCP clients
- 29 -
DNS Service
After modifying the parameter of DHCP Servercurrent configuration must be saved, and then reboot the
IAD.
When IAD needs to dynamically map domain name to the IP address, the function of DNS server must be
started.
In this page, the parameters as following can be configured.
a) Enable DNS Service or not: the parameters below can not be configured until enable the DNS service;
b) Primary DNS service: This configuration can not be null or "0.0.0.0";
c) Slave DNS service (optional): "0.0.0.0" means there is no need to configure.
l
NTP Service
After modifying the parameter of NTP Servercurrent configuration must be saved, and then reboot the
IAD.
In this page, the parameters as following can be configured.
a) Enable NTP Service or not: the parameters below can not be configured until enable the NTP service;;
b) Primary DNS service: This configuration can not be null or "0.0.0.0";
c) Slave DNS service (optional): "0.0.0.0" means there is no need to configure;
d) Time Zone: Time zone ranged from -12 to 13.
l
STUN
After modifying the parameter of STUNcurrent configuration must be saved, and then reboot the IAD.
Simple Traversal of User Datagram Protocol (UDP) Through Network Address Translators (NATs) (STUN)
is a lightweight protocol that allows applications to discover the presence and types of NATs and firewalls
between them and the public Internet.
In this page, the parameters as following can be configured.
a) Enable STUN or not: the parameters below can not be configured until enable the STUN service;
b) STUN Server IP: If the STUN Hostname have been configured, STUN Server IP could do not be
configured. "0.0.0.0" means there is no need to configure;
c) STUN Server Port: STUN Server Ports ranged from -12 to 13.
d) STUN HostnameIf the STUN Server IP has been configured, STUN Hostname could do not be
configured. Null means there is no need to configure
l
802.1X
After modifying the parameter of 802.1Xcurrent configuration must be saved, and then reboot the IAD.
802.1X Network Access Control Protocol. The user name and password are provided by ISP. When the
802.X service is start, Access Authentication will be repeat three times if connecting the 802.1X server
failed.(one time at 30s intervals). After authenticated successfully, device start the network function.
- 30 -
NAT Server
After modifying the parameter of NAT Servercurrent configuration must be saved, and then reboot the
IAD.
Starting the NAT Server, other devices can get the resource of IADs WAN port through IADs LAN
port.
In this page, the parameters as following can be configured.
a) Enable NAT Server service or not.
Audio Codec
Set voice as ITU-T codec algorithm standards. IAD support G.711A, G.711U, G.723, G.729, and G.726
(16k, 24k, 32k, and 40k). User could choose one or more audio codec modes and set their NOB. One of the
algorithms must be assigned as default. The grey button means the mode of audio codec is not supported.
Attention
a). MG6002/MG6032 only support G.711A, G.711U, G.723, G.729.
b). MG6004/MG6008 cant support G.723.1 and G.729 at the same time, user could select one of them.
c). G.726 payload type must be different from RFC2833 payload type.
l
a)
b)
c)
d)
e)
f)
g)
Voice
Echo canceller: Check to enable echo cancellation;
SCE: Enable silence compression, the IAD can check the silent voice packages and compress them to
reduce bandwidth of the network. If the SCE is not enabled, the silent voice packages will be produced
and transmitted. Comfort noise will be sent during the period of silence to make user listening
comfortable;
Input gain: set local voice volume. Value range is -31dB to 31 dB and to -1dB by default. Actually user
could only set the value range from -25 to 10, otherwise the device will send the dialing tone all the time,
and the keystrokes will have no reaction.
Output gainSet remote voice volume. Value range is -31dB to 31dB and to -1dB by default.
Voice delay levelIt is divided to five level, they are minimal, less, moderate, greater and maximal.
Delay reduces with the level lowing, at the time ability of preventing time jitter reduces either, this will
make worse voice quantity.
RTP Start Port: During the call, media stream communicate through RTP ports. User just needs to
configure the RTP start port, system will compute the range of the RTP ports according to the device
series and the RTP start port. RTP ports range of MG6000 Series is 12000 to 14000 and 13000 by
default.
Voice Packets TOS: Configure the IP TOS value. There are five IP TOS: Default value, Minimize delay,
Maximize throughput, Maximize reliability, and Minimize monetary cost.
Attention
The default value of input/output gain is -1db. If the voice is too low, you can turn up the input/output gain
l Tone
a) DTMF gain: set volume of keypad tone. Value rage is -31dB to 0dB (maximum) and to -4dB by default,
b) DTMF transport mode: transport mode of keypad tone during calls. It can be set as transmit by voice,
RFC2833, INFO message.
i.
If setting as transmit by voice, keypad tone will transport by voice signal.
ii.
If setting as RFC2833, keypad tone will transport by RFC2833 format.
iii.
If setting as INFO message, keypad tone will transport by INFO format.
c) RFC2833 Payload type: If setting DTMF mode as RFC2833, this indicates the type which codec
- 32 -
l FAX
a) FAX Mode: Select the way fax calls are handled: Transmit by voice or T.38.
b) Use new RTP portThis configuration only can be configured when the fax mode is T.38. It is be used
whether to open a new RTP port for T.38 FAX.
c) Max Fax Rate: set the maximum fax rate. This configuration only can be configured when the fax
mode is T.38. Select from the drop-down list either: 2.4 Kbps, 4.8 Kbps, 7.2 Kbps, 9.6 Kbps, 12 Kbps or
14.4 Kbps (default).
d) FAX code error correct: Check to enable fax error correction mode (ECM). This configuration only
can be configured when the fax mode is T.38. Default is disabled
e) Redundancy for Fax Relay: Adjust redundancy of RTP to adapt worse network environment, this will
bring extra system expenses. This configuration only can be configured when the fax mode is T.38.
Value range is 0 to 4.
f) Use Offer Mode: This configuration only can be configured when the fax mode is T.38. If enable this
mode, it will neednt to negotiate about T.38 arithmetic when the T.38 fax was started.
g) Fax Gain: Select the fax gain. Value range is 9db to 15db.
Attention:
a). Transmit by voice only supports G.711A and G.711Mu, if select transmit by voice mode to send FAX,
G.711A or G.711Mu must be enabled.
b). T.38 FAX mode doesnt need the support of voice arithmetic
c). MG6002/MG6004/MG6008 support transmit by MODEM, but the FAX mode must select transmit by
voice mode, if select T.38, this function will be disabled.
- 33 -
All kinds of users could enter this page; all the users have the authorization to configure except common
users.
After modifying the parameter of Media streamcurrent configuration must be saved, and then reboot the
IAD.
l SIP Server
a) Register Server: User could set less or even no routes by using a register Server. IAD updates
register information on the SIP server periodically, and register interval is the period between one
register message and the next one. User can set register IP or domain name or both of them and IAD
will find the proxy by IP address first.
b) Backup Server: Optional configuration. User can set register IP or domain name or both of them like
register server. Once the register server failed to work, backup server will take over it to ensure the
calls going on normally.
c) Proxy Server: Optional configuration. It works just like a gateway. If the Proxy Server is started, all
the signaling packages will be sent to it first. Like register server, the priority of IP is higher than
domain name. IP will be processed first.
Attention
a). The priority of register server is higher than backup server. All the calls will be set up by the register
server if it works well.
b). If User registers IAD by domain name, the DNS must be configured.
l Advanced Config
a) Inviter Linger Time: Value rage is 100ms to 65535ms and to 32000ms by default.
b) Provision Time: Value rage is 100ms to 3600000ms and to 180000ms by default.
- 34 -
- 36 -
Line config
Figure 4-10
All kinds of users could enter this page; all the users have the authorization to configure except common
users.
The parameter of prefix, Phone Number, Registered, Authentication Name Authentication
Password will take effect immediately after be modified. Other configuration must be saved, and then reboot the
IAD after be modified.
a) Gateway number prefix: Like the PSTN prefix, its the common prefix of all the extensions that connect
with the gateway.
Attention
a). View from the outside line, the number of every port are composed by prefix and Phone Number. The
length prefix + phone number cant be more than 29 digits.
b). Extension number can be composed by prefix and Phone Number, also can be the Phone Number.
c). After modified the parameter of prefix, Phone Number, Registered, Authentication Name
Authentication Password, click modify and the modification will take effect immediately. Other configuration
must be saved, and then reboot the IAD after be modified. To ensure the modification continue to be valid, please
save the configuration after modifying.
- 37 -
Attention
a). /, *, $ and space can not appear in calling name.
d) Registered, Authentication Name, Authentication Password: If register server or proxy server start the
function of authentication, IAD should provide authentication information to them. In this case, the option of
Registered must be set yes, and Authentication Name and Authentication Password must be filled out.
e) Port mode: Port modes are different base on the port type. FXS port has two port modes: default and
hotline. Default mode is the mode that FXS port connects with the phone. This is the largest application of the
model. If the User set the FXS port mode as hotline, the Hot-line number must be set. After the configuration take
effect, the phone which connects with the port will dial the hotline number automatically when you pick up the
receiver.
f) Transfer Port (Incoming): Only can be configured when the port is FXO. For FXS port, transfer port
- 38 -
Attention
a). The function of call forward is effective for both outside line phones and extension phones. The call
forward number could only be set as the number of the other port in the same device.
b). The three numbers of Call Forward on Unconditional, Call Forward on Busy, Call Forward on No
Answer can be configured in every port. If you enable the function of Call Forward on Unconditional, the
function of Call Forward on Busy and Call Forward on No Answer will be no meaning.
k) Call Forward on Unconditional: When selected, incoming calls are forwarded independently of the status
of the endpoint
l) Call Forward on Busy: When selected, incoming calls are forwarded only if the endpoint is busy.
m) Call Forward on No Answer: When selected, incoming calls are forwarded only if the endpoint does not
answer before a pre-configured timeout.
4.2.8
Route table
4.2.8.1
Click the Route Table, and enter the page of route table, user can preview, add, delete, or modify the
number mapping, and the page shown as below:
- 39 -
All kinds of users could enter this page; all the users have the authorization to configure except common
users.
All the digit map parameters which had been modified, will take effect immediately but make sure the
modified parameters can be applied next time, please save the configuraion, if you have modified the parameters.
The parameters of number mapping show as below.
a). There are 100 number mappings at most.
b). It display 10 number mappings in one page, preview other page please click Prev or Next.
c). IAD series products supports 4 kinds of route type: SIP(by IP),TEL connection, FXO connection and
FXO connection, however, The MG6008 just supports SIP(by IP) and TEL connection.
d). The IAD series products support the number with 29 digits at most.
e). The device not only can set fixed number router, but also can cut off the appointed lengths number or
automatically add appointed prefix to call by need. The number route mappings description of Fig. 4-12, shown
as below:
1). According to the first number route mapping, the prefix is 12, number length is 3, so the number 121,
122~129 is match, will sent to the device which IP address is 138.0.0.221.
2). According to the second number route mapping, the IAD will cut off the 3 digit in the front of the
number which prefix is 12395, length of number is arbitrary, and then sent to the device which IP address is
138.0.0.221. So if the user dials the number 12395832, and the number that the IAD sends is 95832.
3). According to the third number route mapping, the IAD will cut off 3 digit in the front of the number
which prefix is 12315,and length is 5, then add 020 in the front, lastly, sent the number to the device which
IP address is 138.0.0.221.So if the user dial the number is 12315, and 02015 will be sent.
f). Generally, the number route mapping should be configured in the case shown as below.
1). Several IAD which havent been registered call each other.
2). Appoint the route by the prefix.
3). When dial the external line, dont want to dial # after the number,
4). The dial-up number using the Tel URI format.
- 40 -
4.2.8.3
Users can delete the items through clicking the delete button after selecting the row that will be deleted.
Multi records can be deleted in series.
Attention
a). When delete several route once, the index which you select must be continuous.
b). After delete the route, please click the Route map to refresh the page.
4.2.8.4
Click the index in the number route map page, and then enter the page, which is used to modify the
parameters of this index.
Attention
After modify the parameters, please click the route map to refresh the page.
4.2.8.5
Route Parameter
Click the Route table-> Route Parameter, and enter the route parameter configuration page shown as
below, Route parameter is about the network call, such as WAN side channels number limit, Network call
timeout, DTMF interval.
- 42 -
4.2.9
automatically
011xxx.T: International rule without prefix
91[2-9]xxxxxxxxx: LD rule with prefix
Fig.
Attention
a). The originally routing map will be deleted, when enable the digit map.
b). After enable the digit map, user also can add number route to the route map.
c). The digit map expression supports 256 characters at most.
4.2.10 Value-added
Click Value-addedand enter the value-added configuration page shown as below. And this page is used to
configure the value-add, such as * key use for special function, # key as dial-out key, transfer and snatch the
call, call hold, conference call, three-way call and etc.
- 45 -
Call snatch
If enable call snatch, when one extension is ringing, but no one answers, another extension can snatch this
call through pressing the snatch function key (the default snatch function key is *.) and dialing the number of
the ringing phone.
For example
Suppose A and B are in the same IAD, and the snatch is enabled, and the snatch function key is *.
- 46 -
Call hold
Suppose A is one using the call hold function, B and C are another, and the call hold function of IAD which
A connected is enabled, and 2 had been configured as the switch key, and 1 had been configured as refuse key.
There are 4 operations describe the call hold function.
Operation1: refuse
When A is communicating with B, C calls A. A will receive the prompt voice, then A taps and presses
button 1 the refuse key to refuse the call from C. And C will receive the busy tone. It is not affected to
the communication between A and B.
Operation 2: accept
When A is communicating with B, C calls A. A will receive the prompt voice, then A taps and
presses button 2, B is hold, and A will communicate with C.
Operation 3: switch
After accept As call, A taps and presses 2, C is hold, then A communicates with B again.
Operation 4: disconnect
1). A disconnect
After switching, A hangs up the phone, then B and C receive the busy tone.
2) B disconnect
After switching, B hangs up the phone, it is not affected to communication between A and C.
3) C disconnect
After switching, C hangs up the phone, A and B communicate again.
l
Call transfer
Call transfer includes: internal transfer, external transfer, blind transfer, consultative transfer, Show as below.
Firstly, Suppose A is callee, B is caller, and C is the transferred, and call transfer of IAD that connecting A is
enabled, and 4 had been configured as transfer key.
Internal transfer
A and C are in the same IAD, in the process of communication, A taps, and it will receive the dial-up signal
or prompt voice, and presses button 4, then dial number of C, the IAD will complete the transfer, A will receive
the busy tone, and B will receive ringback signal, and C will ring.
1) After A hang up the phone, C picks up the phone, it can communicate with B.
2) C picks up the phone, it can communicate with B, and this time A hang up the phone, It is not affected to
the communication between C and B.
External transfer
A and B are in the same IAD, and C is in another IAD, in the process of communication, A taps, and it will
receive the dial-up signal or prompt voice, and presses button 4, then dial number of C, the IAD will end the
communication between A and B. and B will invite a new call to C, A will receive busy tone, if C is free, C will
ring, and B will receive ringback signal.
1). After A hang up the phone, C pick up the phone, and it can communication with B, and its status is OK,
display rightly the incoming number.
2). C pick up the phone, and it can communication with B, and the C hang up the phone, and status of C is
OK, display rightly the incoming number.
Blind transfer
- 47 -
Conference call
Note: The conference call function need the support of relevant platform.
Conference call function support three-way or above calling at the same time.
Three-way calling
Firstly, Suppose that A invite the three-way calling, and the IAD which A is connecting enable the three-way
calling, 5 button had been configured as three-way calling key.
The description of three-way calling shown as below:
When A communicates with B, and A taps, B is hold, and A presses button 5, After A receive the dial-up
signal, dial the number of C, and A will receive the ringback signal, and C will ring at the same time, if C pick up
the phone, A can communicate with C. If the call hold is enabled, the switching key of call hold can achieve the
switching of call hold.
Attention
a). If register to backup server, it will not support the add-values.
b). Three-way calling do not support the G.726 arithmetic.
c). If enable tap event report, the value-adds that use the tap will be disabled.
- 48 -
- 49 -
AttentionVLAN configuration parameters will take effect immediately. If add tag in the Vlan mode (in
each Vlan mode), it will lead to the Web Network Management cannot be log on to through WAN port. But you
can log on to the Web Manage through the LAN port. Please dont remotely modify the VLAN parameters
through WAN
- 51 -
- 52 -
- 53 -
Attention
a). When reset the IAD to factory default configuration, some parameters will take effect after the device
restarts.
b). Network management needs to connect with the device again after the device restarts.
c). Start TFTP server and select the directory on the PC before TFTP operation, and specify the file name
(The max length is 50 characters) and the address of TFP server at the same time. TFTP server could be
found in accessory CD;
d). The DSP kernel of MG6002 support G.723.1 and G.729 arithmetic at the same time, so it is not need to
update the DSP kernel.
e). The early version of MG6002/MG6004/MG6008 may not support HTTP download (PC->IAD).
- 54 -
Attention
A). The web network management parameters operations of MG6000 series products refer to the chapter 4.2
Operation of Logging in Web
5.1.1
IAD (8)>enable
Password:
The user will log on to the privilege mode, after typing the correct password. The default password of
privilege mode is: admin.
The command prompt of privilege mode is: IAD (8)#
Attention: It is allowed to input three times, if the password is error.
5.1.2
Language
This CLI language supports the Chinese and English. The CLI commands explanation as following in
English.
IAD (8)#set language
Please select the language used in CLI:
0 -- Chinese ()
1 -- English ()
->[0]:1
You have selected [English] as CLI language, please save configurations for last use.
AttentionThe configuration will take effect after setting successfully. But please save configurations for last
use.
5.1.3
5.1.3.1
Version information
Status of POTS
a). Display
IAD (8)#show pots-status
----+------------------------+--------+--------------+------------------------+
Port | Port Number
| Role | Status
| Peer Number
0|82592110
|
| Idle
|
1|82592111
|
| Idle
|
2|82592112
|
| Idle
|
3|82592113
|
| Idle
|
4|82592114
|
| Idle
|
5|82592115
|
| Idle
|
6|82592116
|
| Idle
|
7|82592117
|
| Idle
|
----+------------------------+--------+--------------+------------------------+
5.1.4
Network parameters
5.1.4.1
Static IP Address
a). Configuration
IAD (8)#set ip
-> Device net interface IP address [138.0.60.1]:138.0.221.81
-> Device net interface netmask [255.255.0.0]:255.255.0.0
-> Accounting net interface IP address [192.168.1.1]:
-> Accounting net interface netmask [255.255.255.0]:
-> Use default gatway?'yes'or'no'[no]:yes
-> Please input default gateway IP [138.0.60.2]:192.168.0.221
->IP configuration will take effect by reseting !
Really want to modify ?'yes'or'no' :yes
Attention
The static IP address that had modified will take effect after saving and reseting.
b). Display
IAD(8)#show ip
Device net interface IP configuration
IP address: 138.0.221.81
Netmask: 255.255.0.0
MAC address: 00:06:04:0a:0b:02
Accounting net interface IP configuration
IP address: 192.168.1.1
Netmask: 255.255.255.0
- 56 -
|
|
|
|
|
|
|
|
|
a). Configuration
IAD(8)#set dhcpclient
-> Enable DHCP client ?'yes' or 'no'[no]:yes
-> Use special DHCP server? 'yes' or 'no'[no]:yes
-> Special DHCP server [0.0.0.0]:138.0.0.221
Must reset to take effect
b). Display
IAD(8)#show dhcpclient
DHCP Configuration Enabled
=============================
DHCP client Status:Enabled
Client End IP Address........:138.0.221.18
Client End Net Mask......:255.255.0.0
DHCP Server IP Address....:138.0.0.221
First DNS IP Address........:61.144.56.101
Second DNS IP Address........:0.0.0.0
Default Gateway IP Address......:138.0.0.221
Dhcp sip server......no information
Position of device............no information
5.1.4.3
5.1.4.4
Attention: Only the ET type of IAD can be used as the DHCP server.
a). configuration
IAD(8)#set dhcpserver
-> Enable DHCP server ?'yes' or 'no'[no]:yes
Start IP ...[0.0.0.0]:192.168.1.20
End IP ....[0.0.0.0]:192.168.1.60
Default gateway IP address...[0.0.0.0]:192.168.1.1
Netmask ...[0.0.0.0]:255.255.255.0
Dhcp server configuration will take effect by reseting !
Really want to modify? 'yes' or 'no'[no]:yes
b). Display
IAD(8)#show dhcpserver
DHCP server Enable
=============================
DHCP server status
...Enable
Start IP
...192.168.1.20
End IP
...192.168.1.60
Master DNS IP address ...61.144.56.101
lave DNS IP address
...202.96.128.166
Default gateway IP address
...192.168.1.1
Netmask
...255.255.255.0
5.1.4.5
a). configuration
IAD(8)#set dns
-> Enable DNS server?'yes'or'no'[no] :yes
-> Primary DNS address[0.0.0.0]:61.144.56.101
-> Secondary DNS address(Enter 0 to disable) [61.144.56.101]:
-> Your configuration will apply when restart!
-> Really want to modify?'yes'or'no'[yes]:yes
b)
Display
IAD(8)#show dns
Enable DNS server:YES
Primary DNS address:61.144.56.101
Secondary DNS address: 61.144.56.101
- 58 -
Attention
Master DNS server address and secondary DNS address can be specified to the same or different
address. If enable the DNS server, the master DNS server address must be specified, but the secondary DNS
server could be disable.
5.1.4.6
NTP parameters
a). Configuration
IAD(8)#set ntp
-> Enable NTP?'yes'or'no'[no]:yes
-> Primary NTP server IP address[]:210.72.145.44
-> Secondary NTP server IP address(Enter 0 to diable) [210.72.145.44]:218.21.130.42
-> Time zone(+8 for China)(-12 -- +13)[8]:
-> Your configuration will apply when restart!
-> Really want to modify?'yes'or'no'[yes]:
Attention
Master NTP server address and secondary NTP address can be specified to the same or different address. If
enable the NTP server, the master DNS server address must be specified, but the secondary DNS server address
could be disable. If disable the secondary DNS server, please set its address to 0. And the time zone must be
specified, if input positive number, it is allow not add + in the front of the positive number, for example, if input
the time zone of China,+8 or 8 is OK.
b). Display
IAD (8)#show ntp
NTP: Enable!
Primary NTP server IP address: 210.72.145.44
Secondary NTP server IP address: 218.21.130.42
Time zone(+8 for China): +8
5.1.4.7
STUN parameters
a). Configuration
IAD(8)#set stun
-> enable stun? 'yes' or 'no'[no]:yes
-> Please input stun server domain name[]:www.localstun.com
->Please input stun server IP address[0.0.0.0]:
-> Please input stun server port [3478]:
-> Your configuration will apply when restart!
-> Really want to modify?'yes'or'no'[yes]:
- 59 -
Attention
a). Simple Traversal of UDP over NATs is a lightweight protocol that allows applications to discover the
presence and types of NATs and firewalls between them and the public Internet.
b). User can specify STUN server or IP address, it is not need to specify both, if enable the STUN server,
please enable the DNS server too.
5.1.5
802.1x parameters
a)
b)
Configuration
MG6008#set 802.1x
->Enable 802.1x?'yes'or'no'[no]:y
->802.1x user name[]:cyndi
->802.1x user password[]:cyndi
Display
MG6008#show 802.1x
Enable 802.1x: YES
802.1x user name: cyndi
802.1x user password: Cyndi
Attention
a). 802.1X providing compatible authentication and authorization mechanisms for devices. 802.1X specifies
a general method for the provision of port-based network access control.
b). Users should input the user name and password that the ISP will provide. If link the server failed or the
user name or the password is wrong, the IAD will retry three times, the interval will be 30 seconds, the phone will
start DHCP if the link remain failed; If the IAD link the server successfully and pass the authentication, the phone
will start the DHCP too.
5.1.5.1
NAT parameters
a). Configuration
IAD(8)#set nat-server
-> Is Enable NAT Server? 'yes' or 'no'[no]: yes
***This Configuration work after reset!***
Really want to modify?'yes' or 'no'[no]:yes
- 60 -
Attention
a). For this function, two IP addresses was needed by IAD: one (WAN IP) used in public networks,
connecting Internet; the other (LAN IP) used in private networks, connecting with PC and other network devices.
If MG6008 is as the NAT server, the other device which connecting it by LAN port can access the Internet.
b). It is suggest to disable NAT server, because more system resource will be occupied, if enable the NAT
server.
b). Display
IAD(8)#show nat-server
NAT Server: Disable
Output Data debug information: NO
Output Trace debug information: No
Output Error debug information: No
Account parameters
a). Configuration
IAD(8)#set account
->Startup network interface accounting service'yes' or 'no' [no]:
-> Generate phone receipt within gateway'yes' or 'no' [no]:
-> While the connect to the Billing-N(S) was broken, setting right of channel toCLOSED
or not'yes' or 'no' [no]::
-> Use default power'yes' or 'no' [yes]:no
-> Domestic prefix is [0]:0
-> International prefix is [00]:00
-> Hongkong prefix [00852]:00852
->Macap [00853]:00853
->Taiwan prefix [00886]:00886
Domestic prefix is:0,International prefix is:00,Hongkong/Macap/Taiwan prefix is:00852,00853,00886
->Restriction on number exclude prefix'yes' or 'no' [no]:yes
->Prefix Number(',' could be used for separation character,supported five maximally)
[]:8259,8331,12186,1126,190
->Port 0 need phone receipt 'yes' or 'no' [yes]:
->Port 0 permission(0-Closed,1-Limited,2-City,3-Domestic,4-Macao/HK/Taiwan,5-International) [5]:1
-> Port 1 need phone receipt 'yes' or 'no' [yes]:no
->Port 1 permission(0-Closed,1-Limited,2-City,3-Domestic,4-Macao/HK/Taiwan,5-International) [5]:2
-> Port 2 need phone receipt 'yes' or 'no' [yes]:
-> Port 2 permission(0-Closed,1-Limited,2-City,3-Domestic,4-Macao/HK/Taiwan,5-International) [5]:3
-> Port 3 need phone receipt 'yes' or 'no' [yes]:no
-> Port 3 permission(0-Closed,1-Limited,2-City,3-Domestic,4-Macao/HK/Taiwan,5-International) [5]:4
-> Port 4 need phone receipt 'yes' or 'no' [yes]:no
- 61 -
5.1.6
Generate CDR
YES
NO
YES
NO
NO
YES
YES
YES
Permission
Limited
City
Domestic
Macao/HK/Taiwan
International
Closed
Limited
City
Media parameters
5.1.6.1
a). Configuration
IAD(8)#set codec
->Default codec:G.711Ulaw
->0----G711Ulaw:Enable!
->1----G711Alaw:Enable!
->2----G7231:Not support!
->3----G729:Enable!
->4----G726_16k:Enable!
->5----G726_24k:Enable!
->6----G726_32k:Enable!
->7----G726_40k:Enable!
->Please choose default codec[0]:
->Please enter parameters for default codec(G.711Ulaw )
->NOB (10 or 20):[20]:
- 62 -
|
|
|
|
|
|
|
|
Attention
a). Audio codec algorithm set the voice as ITU-T codec algorithm standards. Application will find which
audio codec algorithm that the DSP kernel do not support and display it.
- 63 -
5.1.6.2
a). Configuration
IAD(8)#set dsp
-> Startup echo canceller?'yes' or 'no'[yes]:yes
-> Startup SCE?'yes' or 'no'[no]:no
-> Input mask?'yes' or 'no'[no]no
-> Input gain(-31 to 31dB)[-1]:-1
-> Output closed?'yes' or 'no'[no]:no
-> Output gain(-31 to 31dB)[-1]:-1
-> DTMF gain(-31 to 0dB)[-4]:-4
Fax Mode::
0 --- Transmit by Voice
1 --- T38
-> Please Select Configuration(0 - 1)[0]:1
MAX FAX rate(bps):
0 --- 2400bps
1 --- 4800bps
2 --- 7200bps
3 --- 9600bps
4 --- 12000bps
5 --- 14400bps
-> Please input MAX FAX rate(0~5):3
-> Redundancy for fax relay (0-4)[0]:0
-> Startup FAX code error correct?'yes' or 'no'[no]:no
-> DTMF transport mode:
0 --- Transmit by Voice
1 --- RFC2833
2 --- INFO message
-> DTMF transport mode[1,RFC2833]:0
Voice delay level:
0 --- Minimal
1 --- Less
2 --- Middle
3 --- Greater
4 --- Maximal
->Select voice delay level[2,Middle]:2
-> Select the signal tone(0:standard 1:Chile)[0]:0
Ring Frequency:
0 --- 25Hz
1 --- 20Hz
->Please Select Configuration(0 - 1)[0]
- 64 -
a). Configuration
IAD(8)#set rtpstartport
-> Input RTP starting port(4000 - 13000)[13000]:13000
Attention
a). The Modified parameters of RTP will take effect after saving and reseting.
b). The RTP parameters is mainly used in the situation sensitive to the bandwidth, recommends using the
default parameters.
b). Display
IAD(8)#show rtpstartport
RTP starting port 13000
5.1.6.4
RTP parameters Frame counts, Max RTP packets in buffer, Configure Redundancy and
Correct remote RTP port
a). Configuration
IAD(8)#set frame-buff
-> Frame counts in each TRP packet(1-5)[1]:1
-> Max RTP packets in buffer(1-300)[5]:5
-> Config Redundancy for RTP (0-5)[0]:0
- 65 -
5.1.6.5
a). Configuration
IAD(8)#set qos
Voice&FAX QoS configure(0.Tos--1.DSCP):0
TOS Default value(0)-Minimize delay(16)-Maximize throughput(8)-Maximize reliabil
ity(4)-Minimize monetary cost(2)
->Please choose TOS value(0-31)[0]:0
SIP signal QoS configure(0.Tos--1.DSCP):0
TOS Default value(0)-Minimize delay(16)-Maximize throughput(8)-Maximize reliabil
ity(4)-Minimize monetary cost(2)
->Please choose TOS value(0-31)[0]:0
->Your configuration will apply when restart!
b). Display
IAD(8)#show qos
-------------------QoS:
ToS DSCP
Voice&FAX |0
|0
SIP signal|0
|0
-------------------5.1.7
SIP Protocol
5.1.7.1
SIP Server
a). Configuration
IAD(8)#set sip
->Enable register server'yes'or'no'[no]:yes
->Register server address(Enter 0 to disable)[138.0.0.176]:138.0.0.221
->Hostname of register server(Enter 0 to disable)[]:
->Register server port(0-65535)[5060]:5060
->Register interval(30-65535)[3600 s]:300
->Enable backup register server'yes'or'no'[no]:no
->Local chat over register server'yes'or'no'[no]:no
->SIP local udp port(0-65535)[5060]:5060
->Enable proxy server?'yes'or'no'[no]:no
->Your configuration will apply when restart!
- 66 -
Attention
a).One or both of the two parameters(register server address and hostname of register server) is needed. They
cannot be NULL together, enter 0 to clear them. The suggested value of the Register server port is 5060. The
register interval is the time interval of the device register to the server.
b). Proxy server just like a gateway, if there is not a proxy, it can be cleared.
c). SIP protocol parameters will take effect after saving and reseting.
b). Display
IAD(8)#show sip
Enable register server:YES
Register server address:138.0.0.221
Hostname of register server:
Register server port:5060
Register interval:300 s
Enable backup register server:NO
Local chat over register server:NO
SIP local udp port:5060
Enable proxy server:NO
5.1.7.2
a). Configuration
IAD(8)#set sipadvanced
->Config all timer with default value?'yes'or'no'[yes]:yes
->Keep alive NAT?'yes'or'no'[no]no
->Register-interval update auto?'yes'or'no'[yes]yes
->Support PRACK?'yes'or'no'[yes]:no
->Support TIMER?'yes'or'no'[no]:
->Reject unsupported extension?'yes'or'no'[no]:
->Use customized parameter in SIP URI coding?'yes'or'no'[no]:
->Enable global number support?'yes'or'no'[no]:
->NO audio when start faxing?'yes'or'no'[no]:
->Use c=0.0.0.0(RFC 2543) in SDP when callhold?'yes'or'no'[no]:
->Use c=0.0.0.0(RFC 2543) in SDP when callhold?'yes'or'no'[no]:
->Register with Full information ?'yes'or'no'[yes]:yes
->Support next nonce ?'yes'or'no'[no]:no
->Support Service-route ?'yes'or'no'[no]:
->Support auth info with first reg request ?'yes'or'no'[no]:
->Support 3GPP header?'yes'or'no'[no]:
->Support Reg-subscribe ?'yes'or'no'[no]:
Privacy type:
0 -- Disabled
- 67 -
Attention
a). Each timer can be set as the default value. The users can also change the settings to satisfy their own
requirement.
b). Keep alive NAT is used to keep the contact with NAT server and IAD with the same IP address. It can
- 68 -
5.1.7.3
Forking parameters
a). Configuration
IAD(8)#set forking
->Is forking INVITE supported? 'yes' or 'no'[no]:yes
->Is forking preference supported? 'yes' or 'no'[no]:yes
Forking Preference:
0 --- disabled
1 --- no-fork
2 --- fork
3 --- parallel
4 --- sequential
->Select forking preference[0,disabled]:0
->1xx timeout(100-3600000 ms)[180000]:180000
->ACK timeout(100-65535 ms)[32000]:32000
***This Configuration work after reset!***
Really want to modify?'yes' or 'no'[yes]:yes
Attention
a). Forking parameters is used to help the platform to send the INVITE request to a number of terminals, and
the device will establish a session with the terminal which return the response 200 OK first.
b). Display
IAD(8)#show forking
Is forking INVITE supported:YES
Is forking preference supported:NO
1xx timeout:180000s
ACK timeout:32000s
5.1.8
SNMP parameters
5.1.8.1
a). Configuration
IAD(8)#set snmp
->Enable register SNMP server'yes'or'no'[no]:yes
->SNMP server address[138.0.0.102]:138.0.0.221
- 69 -
5.1.8.2
Alarm parameters
a). Configuration
IAD(8)#set alarm-config
->Alarm Configuration will apply when Enable SNMP!
->Enable Alarm Message Upload'yes'or'no'[yes]:yes
->Interval of Alarm Message Upload(10-1000)[20*10ms]:20
->Enable Alarm Message Store'yes'or'no'[no]:no
->Your configuration will apply when restart!
->Really want to modify?'yes'or'no'[yes]:yes
b). Display
IAD(8)#show alarm-config
Enable Alarm Message Upload:YES
Interval of Alarm Message Upload:20*10ms
The Index of Alarm Message:0
5.1.9
Line Configuration
5.1.9.1
Local phonebook setting - prefix, port number, Registered or no, Forbid displaying
- 70 -
|
|
|
|
|
|
|
|
5.1.9.2
Call Forward
a). Configuration
IAD(8)#set callforward
->Please choose port:(0-7)[0]:
->Enable callforward function?'yes'or'no'[no]:yes
->Enable unconditional callforward function?'yes'or'no'[no]:no
->Enable when busy callforward function?'yes'or'no'[no]:yes
->Please enter when busy callforward number:[]:82598321
->Enable no answer callforward function?'yes'or'no'[no]:
->Really want to modify?'yes'or'no'[yes]:yes
IAD(8)#set callforward
->Please choose port:(0-7)[0]:6
->Enable callforward function?'yes'or'no'[no]:yes
->Enable unconditional callforward function?'yes'or'no'[no]:
->Enable when busy callforward function?'yes'or'no'[no]:
->Enable no answer callforward function?'yes'or'no'[no]:yes
->Please enter no answer callforward number:[]:82598625
->Timer for no answer callforward: (500-9000)[2000*10ms]:2000
->Really want to modify?'yes'or'no'[yes]
IAD(8)#set callforward
->Please choose port:(0-7)[0]:7
->Enable callforward function?'yes'or'no'[no]:yes
->Enable unconditional callforward function?'yes'or'no'[no]:yes
->Please enter unconditional callforward number:[]:82597654
->Enable when busy callforward function?'yes'or'no'[no]:
->Enable no answer callforward function?'yes'or'no'[no]:
->Really want to modify?'yes'or'no'[yes]:yes
b). Display
IAD(8)#show callforward
0 port's callforward function: Enable!
Unconditional callforward function: Disable!
When busy callforward function:
Enable!
When busy callforward number:
82598321
When no answer callforward function: Disable!
1 port's callforward function: Disable!
2 port's callforward function: Disable!
3 port's callforward function: Disable!
4 port's callforward function: Disable!
5 port's callforward function: Disable!
6 port's callforward function: Enable!
- 73 -
5.1.9.3
a). Configuration
IAD(8)#set call-group
->Use grouping retransfer incoming call'yes'or'no'[no]:yes
->Please input port number (0-7)[0]:
->Assigned grouping number (0-7)[0]:
Continue ?'yes' or 'no' [yes]:
->Please input port number (0-7)[1]:
->Assigned grouping number (0-7)[1]:0
Continue ?'yes' or 'no' [yes]:
->Please input port number (0-7)[2]:
->Assigned grouping number (0-7)[2]:0
Continue ?'yes' or 'no' [yes]:
->Please input port number (0-7)[3]:
->Assigned grouping number (0-7)[3]:1
Continue ?'yes' or 'no' [yes]:
->Please input port number (0-7)[4]:
->Assigned grouping number (0-7)[4]:1
Continue ?'yes' or 'no' [yes]:
->Please input port number (0-7)[5]:
->Assigned grouping number (0-7)[5]:1
Continue ?'yes' or 'no' [yes]:
->Please input port number (0-7)[6]:
->Assigned grouping number (0-7)[6]:2
Continue ?'yes' or 'no' [yes]:
->Please input port number (0-7)[7]:
->Assigned grouping number (0-7)[7]:2
Continue ?'yes' or 'no' [yes]:NO
b). Display
IAD(8)#show call-group
Grouping retransfer incoming call status:Enable
- 74 -
5.1.9.4
Port Type
210
211
212
213
214
215
216
217
Grouping-nu
0
0
0
1
1
1
2
2
a). Configuration
IAD(8)#set sipuser
->Enter port index(0-7)[0]:0
->0 Port number:82598110
->Caller name(Enter 0 to disable)[]:
->User name(Enter 0 to disable)[]:81108259
->Password(Enter 0 to disable)[]:81108259
->Config other ports ?'yes'or'no'[yes]:yes
->Enter port index(0-7)[1]:1
->1 Port number:82598111
->Caller name(Enter 0 to disable)[]:
->User name(Enter 0 to disable)[]:81118259
->Password(Enter 0 to disable)[]:81118259
->Config other ports ?'yes'or'no'[yes]:yes
->Enter port index(0-7)[2]:
->2 Port number: 82599210
->Caller name(Enter 0 to disable)[]:
->User name(Enter 0 to disable)[]: 92108259
->Password(Enter 0 to disable)[]:92108259
->Config other ports ?'yes'or'no'[yes]:no
b). Display
IAD(8)#show sipuser
----+--------+-----------------------+--------------------------------+
Port |Type
|SIP Status
|Prefix and Portnumber
|CallerName
|UserName
----+--------+-----------------------+--------------------------------+
0|FXS
|success
|8259+8110
|
|81108259
----+--------+-----------------------+--------------------------------/
1|FXS
|success
|8259+8111
|
|81118259
----+--------+-----------------------+--------------------------------/
2|FXS
|success
|8259+9210
- 75 -
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Attention
a). Caller name, user name and password may not specify, they are optional. And if they are specified, they
also can be canceled by configuring as 0, however, when the register or proxy servers require authentication, user
name and password must be configured;
b).when preview ityou will see the registration status, including waiting, registering, success and failed,
when the state is failed, it will display the reasons.
5.1.9.5
a). Enable
IAD(8)#refresh portnum
->take effect new port number[y/n]y
port 0: num-0, regchange-0, reg-1
port 1: num-0, regchange-0, reg-1
port 2: num-0, regchange-0, reg-1
port 3: num-0, regchange-0, reg-1
port 4: num-0, regchange-0, reg-1
port 5: num-0, regchange-0, reg-1
port 6: num-0, regchange-0, reg-1
port 7: num-0, regchange-0, reg-1
->the numbers have not taken effect!
Attention
a). refresh portnum is used to make some parameters which had be modified take effect immediately, these
parameters are include the prefix, port number, register or not and user name and password of
authentication and registration, but in order to ensure it will remain take effect after restart, please save the current
- 76 -
5.1.9.6
Incoming number display parameters The Interval between incoming numbers and first ring,
incoming numbers gain and enable calling number restrict or not
a). Configuration
IAD(8)#set innumshow
->The Interval between incoming numbers and first ring(50-150)[100]*10ms:100
->Incoming numbers gain(0-15dB)[9]:9
->Enable Calling Number Restrict(Hint if Enable Calling Number show --P--) 'yes' or'no'[no]:no
Modified configuration anyway ?'yes' or 'no'[yes]:yes
b). Display
IAD(8)#show innumshow
The Interval between incoming numbers and first ring: 100*10ms
Incoming numbers gain: 9dB
Enable Calling Number Restrict(Hint if Enable Calling Number show --P--): No
5.1.9.7
a). Configuration
IAD(8)#set calling-number
->Please input port number(0-7)[0]
->Modify calling number flag(0-No change;1-Appointed number;2-Modify Number)[0]:0
->Continue'yes'or'no'[yes]:
->Please input port number(0-7)[1]
->Modify calling number flag(0-No change;1-Appointed number;2-Modify Number)[0]:1
->Appointed number[]82598555
->Continue'yes'or'no'[yes]:yes
->Please input port number(0-7)[2]:7
->Modify calling number flag(0-No change;1-Appointed number;2-Modify Number)[0]:2
->Calling number interception length [0]:1
->Calling number need extra prefix 'yes'or'no'[no]:yes
->Extra prefix []:020
->Continue'yes'or'no'[yes]:no
b). Display
IAD(8)#show calling-number
Port Type
Modify calling num flag
0 FXS
Unchanged
1 FXS
Appointed
82598555
2 FXS
Unchanged
3 FXS
Unchanged
4 FXS
Unchanged
Appointed num
- 77 -
FXS
FXS
FXS
Unchanged
Unchanged
Modified
020
- 78 -
Attention
If active DSP Channel after collecting phone number end, you will receive the prompt voice immediately.
This case is usually not appearing. The default configuration is disabled; please do not arbitrarily change this
configuration item.
b). Display
IAD(8)#show pbx-para
DTMF interval: 1000*10 ms
Network call timeout: 2000*10 ms
WAN side channels number limit: 8
Whether Active DSP Channel after collecting phone number end: NO
5.1.11 Digitmap Configuration
Digit map is a form of routing configuration. It based on regular expression, and can configure several routes
once.
a). Configuration
IAD(8)#set digitmap
->Enable Digit Map(enable will delete all gw-table info) 'yes'or'no'[no]:yes
->Digit Map[[2-9]11|0T|011xxx.T|91[2-9]xxxxxxxxx|[1-8]xx]:
->T Timer[10s]:10
->Routing IP Address[0.0.0.0]:138.0.0.221
->Routing Port(0-65535)[5060]:
Attention
If enable the digit map function, originally routing map will be deleted.
- 80 -
b). Display
IAD(8)#show extended-service
Use '#' key as dial out(0-no, 1-yes): 1
use '*' key for special function (0-no, 1-yes): 0
If Tap key need to send up(0-no, 1-yes): 0
If special key use Escape Sequence(0-no, 1-yes): 0
Snatch Function: Enabled
Snatch key:*
Transfer Function: Enabled
Transfer key: Tap+4
Callhold function: Enabled
Callhold answer incoming call key: Tap+2
Cancel Callhold call key: Tap+1
Threeway calling function: Enabled
Threeway calling function key: Tap+5
Conference Function: Enabled
URL of conference: localconference@gaoke.com.cn
conference dial number: 200
conference start key: Tap+3
conference dialling Function key: ^
conference dialling cancel key: ^
If Enable Mailbox Function: NO
->Tap+Digit means to pat the spring first then press digit, ^(Shift+6) means topat the spring!
5.1.12.2 MWI Server Address
a). Configuration
IAD(8)#set mwiserveraddr
->Please input MWI server address[]:localmwiserver@gaoke.com.cn
Modified configuration anyway ?'yes' or 'no'[no]:yes
b). Display
IAD(8)#show mwiserveraddr
MWI server address:localmwiserver@gaoke.com.cn
5.1.13 VLAN Configuration
1. route type don't add tag
a). Configuration
IAD(8)#set vlan
VLAN mode:
0------route mode
1------bridge mode
2------custom mode
3:vlan disable
Please choose VLAN mode[0]: 0
- 82 -
AttentionVLAN configuration parameters will take effect immediately. If add tag in the Vlan mode (in
each Vlan mode), it will lead to the Web Management cannot be log on to through WAN port. But
you can log on to the Web Manage through the LAN port.
Usage
- 85 -
Attention
the command that is tftp host put sys filename is forbidden.
l
operation
a). User should open a TFTP server in the workstation, and configure the parameters.
b). Make sure the workstation and the IADs network connect well, and ping each other to check it.
c). User needs to specify the TFTP server address, operational file name (system file, configuration file,
telephone book, DSP kernel).
Attention
a). First, make sure the HTTP server is enable.
b). Secondly, make sure the HTTP client and the HTTP server connect well, ping each other to check it.
c). Lastlybefore input the command <set httpdownload-start>, user need to specify the address and the
port of HTTP server and the type of the file which can be application software, binary configuration file, text
configuration file, kernel file, DSP kernel file, and the update file name.
Attention
a). The password of common user will be use when access by telnet.
b). The new password will take effect immediately.
Attention
The new password will take effect immediately.
- 88 -
- 89 -
- 90 -
- 91 -