Professional Documents
Culture Documents
No. 120 Series Series Dial Calipers 120Z-9
No. 120 Series Series Dial Calipers 120Z-9
No. 120 Series Series Dial Calipers 120Z-9
120Z-9 9”
The Only American Made Dial Caliper … This is one of the handiest measuring tools available, used by
mechanics and toolmakers everywhere. It is direct reading, reliable and accurate.
Comes with Finished Wooden Case.
Readability Features
◆ Sharp, clear dial graduations of .001” – .100” in one revolution
◆ Sharp, black graduations on the satin finished bar, every .100”
◆ White inch dials
Ease-of-Handling Features
◆ Knife-edge contacts for both inside and outside measurements
◆ One hand use with the thumb-operated, fine adjustment roll
◆ Lock screw for dial bezel
◆ Lock screw for holding the sliding jaw in position
◆ 9” model have a covered rack depth rod
◆ Parallel lines can be scribed on workpiece by setting caliper jaw to the required dimensions, locking the
movable jaw with the lock screw and then using the front edge of the fixed jaw as the scribing surface
Moderately priced levels for all-around use; machinists, maintenance and set-up mechanics.
• The base of the levels has an involute groove running the full length, which provides a reliable seat for
round work
• All sizes have a main vial and double plumb vials. Each vial has two graduated lines
• The main vials have approximately 19-minute sensitivity, meaning if the bubble moves 1/8" off the
graduated lines, the out-of-level is approximately .080" per foot. If the bubble is off 2mm, then the out-of-
level is approximately 4.4mm per meter
• Small but powerful magnetic base, with 70 lbs. (320 N) holding force
• Positive On/Off switch
• Base Dimensions: 1³⁄₁₆" x1⁹₁₆" x1³⁄₈" (9.5mm) stem or standard dovetail mount
• Articulating arm, powerful central locking knob, full 360° horizontal positioning, 180° vertical positioning
• Maximum Horizontal Reach: 4.750" (120mm) - - Maximum Vertical Reach: 7.500" (190mm)
• Very sensitive fine-adjustment thumb screw
These Electronic height Gages provide a versatile and economic solution for most height measurement
applications. All measuring information from these tools can be entered directly into Starrett Data Collection
Systems for analysis, data collection, and hard copy documentation.
Specifications:
LCD Readout Resolution 0.0005" (.005mm), Bar Graduations 0.100" and 5mm increments.
Instant inch-millimetre conversion.
Carrier and scriber designed to read from zero.
Hold control feature retains a reading at any position.
Plus or minus direction selector for reading correct measurements.
Hardened and ground scriber.
Fine adjustment for precise positioning accuracy. Lock screw.
Powered by two 3V lithium coin-cell batteries with a life of over 1 year.
Automatic shut-off to conserve battery life after 30 minutes of non-use.
No. 20-3 Hardened Steel Square 3”
No. 384A Series, Steel Parallels, 6" (150mm) Length, Pair: 1/8" (3mm) Thick, 1" (25mm)
Width
No. 1202-12
No. 1202-8
No. 1202-6
N/A
No. 1202-4
N/A
With the ability to provide quick, accurate measurement of O.D., I.D. and depth, the dial caliper is the most
versatile precision hand tool on the market.
No. 1202 Dial Calipers are based on the caliper that has been the first choice of metal working professionals for
decades. No. 1202 Dial Calipers are available in 4, 6, 8 and 12 versions.
Readability Features
◆ Sharp, clear dial graduations of .001” with .100” per revolution
◆ Sharp, black graduation so n the satin finished bar, every .100”
Ease-of-Handling Features
◆ Knife-edge contacts
◆ Thumb-operated fine adjustment roll
◆ Adjustable bezel
◆ Lock screws for sliding jaw and dial bezel
This vernier caliper is the ultimate example of slide caliper design. It is more accurate, has the easiest reading
vernier style, is stronger and is offered in much longer lengths than other slide calipers.
Readability Features
◆ Long 50-division vernier scales, made popular by Starrett. This feature permits just half as many bar
graduations as conventional single-vernier tools. These widely-spaced graduations make possible easy reading
to .001” or 0.02mm without requiring a magnifying glass
◆ Flush fitting of the vernier scales to the main scale means that these are in the same plane, which eliminates
parallax. Vernier scales are adjustable
◆ The open-face design of the slide allows both the inside and outside vernier scale on the same side, thus
allowing both verniers to be read without turning the tool over
◆ Black lines and figures against the Starrett satin chrome finish make reading a pleasure, not an effort
◆ Screw-type adjusting nut allows for fine measuring adjustments
◆ Lock nut to hold measurements
This versatile gage was specifically designed for gage makers, inspectors, tool and die makers and
machinists. There is no other similar gage available that combines the design, accuracy and
usefulness of this tool for fine height setting and transfer within its range.
• Features and attachments that make this a truly universal gage are – Scriber Attachment that
can be used as a height gage for comparison measuring with test indicators, or as a surface
gage for scribing – an offset attachment or "foot" that permits setting in narrow areas or
working 1/8" (3.2 mm) below the base line – and 1" (25.4 mm) and 3" (76.2 mm) extensions to
increase the measuring range
• Gage has a stable width-to-length ratio of 3/4" (19 mm) wide and 5 1/4" (130 mm) length
• Base and slide forgings are hardened and all working surfaces are accurately ground
• The exclusive combination flat and "V" ways on the slide and base provides extreme
accuracy, and the three-point contact provides longitudinal movement without side play
• A fine adjustment for closer accuracy and faster settings eliminates slow, tedious
tapping to set the gage. There is no other similar gage with this important feature
• Applications – Can be used as a height gage, scriber, planer and shaper gage, for gap
measurement, as an adjustable parallel, for transferring settings with indicators, for checking
and layout work on surface plates, and with gage blocks or sine bars
• Works as a precision level for use in machine set ups and gage work
• In all these applications flush surfaces permit use on the base, the end, the top of the slide and
either side
Starrett Electronic Indicators have simple, powerful, easy-to-use function. Versions are available for
inch/metric and metric only.
Features
◆ Large, easy-to-read LCD
◆ AGD group 2 size
◆ Range: .500" or 12.7mm
◆ Resolution: .0005" or .01mm
◆ Power On / Off button
◆ Reverse travel (± control indicates direction)
◆ Zero setting at any position
◆ Long battery life
◆ 3/8" diameter stem for inch/mm model (8mm on metric-only model)
◆ 4-48 spindle thread on inch/mm model (M2.5 X .45 thread on metric-only model)
◆ Lug-on-center back + additional flat back
◆ Dust cap
◆ Plastic storage case with clear cover
Simply move the spindle and the indicator turns ON, keeping true spindle position. Instant inch/millimetre
conversion. Automatic OFF after 5 minutes of non use. 3/8” diameter stem. Zero at any position. Large,
easy to read LCD display.
These tools are used to measure the thickness of work sections such as ribs, lands, fins, cutting edges on
form tools, and chordal thickness of gear teeth. Because of their large anvil and spindle faces.
Readability Features
◆ Starrett satin chrome finish – no glare – resists rust
◆ Advanced sleeve design with staggered lines and distinct figures for precise and easy readability
Ease-of-Handling Features
◆ Balanced frame and thimble design insure easy handling and better readability
◆ Ring-type knurled lock nut for quick and sure locking lock nut with Ratchet Stop
◆ The combination ratchet and speeder for uniform pressure and quicker adjustment on all sizes
◆ Anvil and spindle discs are 1/2” (12.7mm) diameter tapering to .015” (0.4mm) edge thickness making it
possible to enter narrow grooves and recesses
These calipers feature a joint that can be quickly and firmly locked by a partial turn of the large knurled
disc. A spring washer under the disc maintains proper tension of the legs when the joint is unlocked.
These calipers are also provided with an adjusting screw to permit fine adjustments for close
measurements. After the legs have been set to approximate size and the joint locked, the final
adjustment is made by a few turns of the knurled adjusting nut.
The legs are made of a high-grade steel and well shaped. They are ruggedly constructed and nicely
finished.
The sizes listed are leg lengths. Their actual measuring capacity is about one-third greater than the
given size of the legs.
38-6
73B-6
Starrett “Yankee” Calipers and Dividers are made from a high-grade steel and well finished.
The legs are made of flat stock and are very durable. The fulcrum stud is hardened and has a smooth
bearing
surface. The bow spring, although flexible, is exceedingly strong to assure reliability.
All sizes are available with either spring nut or solid nut. The Starrett quick-adjusting automatic-closing
spring nut is designed for making fast, positive adjustments. The threads of the nut firmly engage the
screw at the slightest pressure from the leg. When the pressure is withdrawn, the nut automatically
releases itself, sliding freely over the screw. This feature saves time in opening and closing.
83B-12
12”
42-6
These calipers have an adjustable point, locking joint and fine-adjustment feature for close
measurements. After the legs have been set to approximate size and the joint locked, the final
adjustment is made by a few turns of the knurled adjusting nut.
Manufacturer Moore & Wright. A large headed nut screw assembly provides a firm and rigid friction
joint, with no play. Upper Jaw & Lower Jaw Length 6”.