Professional Documents
Culture Documents
Black Box PC Setup Guide R1
Black Box PC Setup Guide R1
Parts In Box
Black Box PC (Set up, RAM Installed, CPU Installed)
Computer Power Supply & Power Lead
Kingston 2GB USB Pen Drive (Ghosted With DOS, Touch and V1.19 Mk3 Software)
Mounting Plate (A-030255)
3n9 Capacitor (EE00227)
Serial Cable (Pin To Pin)
M4 Bolt (4 Off)
Page 1 of 7
Monitor Modification
Before fitting the new PC, it is necessary to replace the capacitor C216 in the Microvitec monitor, the
original is 3600pf (3N6 J1600) should be replaced with 3900pf (3N9) This will prevent the EHT from
becoming too high when the picture width is adjusted and damaging the line output transistor.
Software Install
Remove the original computer hard drive and copy contents to laptop.
*Note that some older Hard Drives are not able to be read using a IDE To USB Adapter. You will need
to use a computer with motherboard IDE.
Copy the following directories / folders (replacing current ones) to the USB Pen Drive.
C:\Bender
C:\V3
Install the computer. Usually mounted to Mounting Bracket or right hand side of panel.
The software, Part Programs etc will all be correct.
*Back-up the Machine Config from the CPU to the computer*
Known Issues
It has been found that there are issues with older software versions. Software versions prior to about
V1.11 will not function correctly with the new PC as you cannot run them in medium resolution(-m). In
this case you will have to upgrade the software on the CPU also. Unfortunately this can cause other
issues, specially on special machines/options. If newer software is installed it is vital that you fully test
the machine.
Newer version of software also look for I/O Board C and ReactionSlide Interlock Input (C8) to be high
(24V)
BIOS Settings
The Bios Settings are mostly DEFAULT settings, with only a few changes, see list below.
Page 3 of 7
Page 4 of 7
Intergrated Peripherals
OnChip IDE Device Press Enter
IDE HDD Block Mode Enabled
IDE DMA transfer Access Enabled
IDE Primary Master PIO Auto
IDE Primary Slave PIO Auto
IDE Primary Master UDMA Auto
IDE Primary Slave UDMA Auto
On-Ship Secondary PCI IDE Enabled
IDE Secondary Master PIO Auto
IDE Secondary Slave PIO Auto
IDE Secondary Master UDAM Auto
IDE Secondary Slave UDMA Auto
SATA Mode IDE
Legacy Mode Support - Disabled
SuperIO Device - Press Enter
POWER ON Function BUTTON ONLY
* XB Power ON Password Enter
* Hot Key Power ON Ctrl-F1
OnBoard Serial Port 1 3F8/IRQ4
OnBoard Serial Port 2 2F8/IRQ3
UART Mode Select - Normal
* RxD, TxD Active Hi, Lo
* IR Transmission Delay Enabled
* VR2 Duplex Mode Half
* Use IR Pins IR-Rx2Tx2
OnBoard Parallel Port - 378/IRQ7
Parallel Port Mode ECP+EPP
EPP Mode Select EPP1.7
EPC Mode Use DMA 3
PWRON After PWR-Fail On
OnBoard Serial Port 3 2E8
Serial Port 3 Use IRQ IRQ4
OnBoard Serial Port 4 Disabled
*Serial Port 4 Use IRQ IRQ10
OnBoard lan Boot ROM Disabled
USB Device Settings Press Enter
USB 1.0 Controller Enabled
USB 2.0 Controller Enabled
USB Operation Mode High Speed
USB KeyBoard Function Enabled
USB Mouse Funtion Enabled
USB Storage Function Enabled
*** USB Mass Storage Device Boot Setting ***
KingtonDataTravler C100. Auto Mode
Page 5 of 7
Power Management
PCI Express PM Funtion Press Enter
PEG Port ASPM Disabled
Root Port ASPM Disabled
DMI Port ASPM - Disabled
ACPI Funtion Enabled
ACPI Suspend Type S3(STR)
Soft-Off By PWR-BTTN Instant Off
Wake-Up By PCI card Disabled
Power On By Ring Disabled
USB KB Wake-Up From S3 Disabled
Resume Alarm Disabled
* Date (Of Month) Alarm 0
* Time (hh:mm:ss) Alarm 0 : 0 : 0
** Reload Global Timer Events **
Primary IDE 0 Disabled
Primary IDE 1 Disabled
Secondary IDE 0 Disabled
Secondary IDE 1 Disabled
FDD,COM,LPT Port Disabled
PCI PIR(A-D)# - Disabled
HPET Support - Enabled
HPET Mode 32-Bit Mode
Intel DTS Feature Press Enter
Intel DTS Function - Disabled
* DTS Active Temperature - 55C
* Passive Cooling Trip point - 95C
* Passive TC1 Value 2
* Passive TC2 Value 8
* Passive TSP Value 10
* Critical Trip Point - 103C
Page 6 of 7
PnP/PCI Configuration
Init Display First PCI Slot
Reset Configuration Data Disabled
Resources Controlled By Manual
IRQ Resources Press Enter
IRQ-3 assigned to PCI Device
IRQ-4 assigned to Reserved
IRQ-5 assigned to PCI Device
IRQ-7 assigned to PCI Device
IRQ-9 assigned to PCI Device
IRQ-10 assigned to PCI Device
IRQ-11 assigned to - Reserved
IRQ-12 assigned to PCI Device
IRQ-14 assigned to - PCI Device
IRQ-15 assigned to PCI Device
PCI/VGA Palette Snoop Disabled
** PCI Express Relative Items **
Maximum Payload Size - 128
Page 7 of 7