Professional Documents
Culture Documents
D155 Ax-5
D155 Ax-5
KOMATSU-iBLADE Specification
MACHINE MODEL
SERIAL No.
D155AX-5
76001 and up
This shop manual may contain attachments and optional equipment that are not available
in your area.
Please consult your local Komatsu distributor for those items you may require.
Materials and specifications are subject to change without notice.
2005
All Rights Reserved
Printed in Japan 03-05 (01)
00-1
GENERAL
CONTENTS
No. of page
01 GENERAL ............................................................................................................................
01-1
10-1
..................................................... 30-1
90 OTHERS ................................................................................................................................
00-2
90-1
D155AX-5
01 GENERAL
SPECIFICATION DRAWING ........................................................................................................................01- 2
D155AX-5
01-1
GENERAL
SPECIFICATION DRAWING
SPECIFICATION DRAWING
Item
Unit
U-tilt dozer
+ Giant ripper
Overall length
mm
8,550
8,155
8,155
8,550
Overall height
mm
4,195
4,195
4,195
4,195
Overall width
mm
4,265
3,955
3,955
4,265
01-2
D155AX-5
D155AX-5
10-1
The drawing shows a pitch dozer and pin puller installed vehicle.
10-2
D155AX-5
1.
2.
3.
4.
Lever positions
A. Blade HOLD
B. Blade LOWER
C. Blade FLOAT
D. Blade RAISE
E. Blade (left tilt)
F. Blade (right tilt)
M. FREE
N. LOCK
O. Blade automatic control selector switch OFF
P. Blade automatic control selector switch ON
Outline
The work equipment control employs a PPC system which uses a PPC valve to move the spools
of the control valve.
Work equipment lock lever (1) is interconnected
with PPC lock valve (4), and when it is at the
LOCK position, the flow of oil in the PPC circuit is
stopped.
D155AX-5
10-3
PPC VALVE
PPC VALVE
For blade lift and tilt
1. PPC valve
2. Shuttle valve
3. EPC valve
10-4
D155AX-5
PPC VALVE
Function
The EPC solenoid valve consists of the proportional solenoid valve portion and the oil pressure
block.
From the control box (TOPCON), an electric signal is sent to the EPC valve according to the
amount that right control lever is moved.
When signal current i is received from the control
box, an EPC output is generated in proportion to
the level of the current to drive the work equipment valve.
The shuttle valve supplies the higher output of
the PPC valve and EPC valve to the work equipment valve to drive the spool.
Operation
1. When signal current is 0 (coil deenergized)
When there is no signal current flowing from the
controller to coil (9), coil (9) is deenergized.
For this reason, spool (6) is pushed to the right in
the direction of the arrow by spring (7).
As a result, port P is closed, and the pressurized
oil passing through the PPC and EPC charge
valve from the charge pump does not flow to the
control valve.
At the same time, pressurized oil from the control
valve flows from port C through port T and is
drained to the tank.
D155AX-5
10-5
PPC VALVE
10-6
D155AX-5
30 DISASSEMBLY AND
ASSEMBLY
REMOVAL AND INSTALLATION OF ROPS GUARD .................................................................................30-2
D155AX-5
30-1
30-2
D155AX-5
90 OTHERS
HYDRAULIC CIRCUIT DIAGRAM (FOR iBLADE SPECIFICATION)........................................................... 90- 3
EELECTRICAL CIRCUIT DIAGRAM (FOR iBLADE SPECIFICATION) ....................................................... 90- 5
D155AX-5
90-1
OTHERS
D155AX-5
90-3
OTHERS
D155AX-5
90-5